Beam Load Calculator

Updated

Beam Load Calculator that turns point, uniform and partial loads into reactions, shear and moment, then checks bending stress, deflection and the safe load for wood or steel beams.

Quick Setup

Measure every position from support A at the left end. Enter a negative load for uplift.

More LoadsNone added

Optional. Blank fields are ignored. A partial load can taper from start to end.

Section DimensionsI 356 in⁴ · S 63.3 in³

Bending about the strong axis. Fillets and corner radii are left out, which is slightly conservative.

Material and Deflection LimitDF-L No.2 · L/360

Wood Fb is adjusted by NDS factors C_D, C_F and C_V; steel uses 0.66 Fy for a compact, braced beam.

Maximum Bending Moment
4,033 lb·ft Sagging
At x = 4.667 ft, bottom of beam in tension · Simply Supported
1,300 lbf Reaction at A
Reaction at B1,100 lbf
Share Carried by A54.2%
Upward support forces that hold all the loads in balance. The larger end reaction is also the largest shear force the beam carries.
764.8 psi Bending Stress
Stress Ratio σ / Fb′85.0%
Section Modulus Needed53.78 in³
Peak bending stress, M divided by S, compared with the allowable stress Fb′ of the chosen material and the section modulus needed.
2,824 lbf Max Safe Total Load
Governed ByBending Stress
Deflection L/360 Allows5,367 lbf
Largest load this beam carries with every load scaled up together, limited by the bending stress or by the deflection limit chosen.
0.1789 in Max Deflection
Span to DeflectionL/805
Allowed at L/3600.4 in
Largest sag found along the span by integrating M over EI, compared with the deflection limit you picked for this kind of member.
Shear, Moment and Deflection DiagramsV, M, Δ
P₁ABShear V1,300 lbf-1,100 lbfMoment M4,033 lb·ftDeflection0.179 in
Values Along the BeamEvery L/10
Position xShear VMoment MDeflection ↓
0 ft1,300 lbf0 lb·ft0 in
1.2 ft1,120 lbf1,452 lb·ft0.05764 in
2.4 ft940 lbf2,688 lb·ft0.109 in
3.6 ft760 lbf3,708 lb·ft0.1487 in
4.667 ft0 lbf4,033 lb·ft0.1707 in
4.8 ft-20 lbf4,032 lb·ft0.1725 in
6 ft-200 lbf3,900 lb·ft0.1787 in
7.2 ft-380 lbf3,552 lb·ft0.168 in
8.4 ft-560 lbf2,988 lb·ft0.1418 in
9.6 ft-740 lbf2,208 lb·ft0.1027 in
10.8 ft-920 lbf1,212 lb·ft0.05393 in
12 ft-1,100 lbf0 lb·ft0 in
Safe Uniform Load by SpanSame section
SpanSafe Uniform LoadGoverns
4 ft2,373 lbf/ftBending
6 ft1,055 lbf/ftBending
8 ft593.3 lbf/ftBending
10 ft379.7 lbf/ftBending
12 ft263.7 lbf/ftBending
14 ft193.7 lbf/ftBending
16 ft148.3 lbf/ftBending
18 ft117.2 lbf/ftBending
20 ft94.92 lbf/ftBending
24 ft61.04 lbf/ftL/360
30 ft31.25 lbf/ftL/360
Beam Formulas for Standard CasesMax M, V, Δ
CaseMax MMax VMax Δ
Simply supported, uniform wwL²/8wL/25wL⁴/384EI
Simply supported, center PPL/4P/2PL³/48EI
Cantilever, uniform wwL²/2wLwL⁴/8EI
Cantilever, end PPLPPL³/3EI
Fixed both ends, uniform wwL²/12wL/2wL⁴/384EI
Fixed both ends, center PPL/8P/2PL³/192EI
Fixed-pinned, uniform wwL²/85wL/8wL⁴/185EI
Fixed-pinned, center P3PL/1611P/16PL³/107.3EI
Step-by-Step SolutionΣF = 0, ΣM = 0
  1. Loads: 600 lbf at 4 ft; 150 lbf/ft from 0 ft to 12 ft
  2. Total load W = 2,400 lbf, moment of loads about A = 13,200 lb·ft
  3. ΣM about A = 0: R_B = 13,200 lb·ft ÷ 12 ft = 1,100 lbf
  4. ΣF = 0: R_A = W - R_B = 1,300 lbf
  5. Section: (2) 2x12, I = 356 in⁴, S = 63.28 in³
  6. Deflection by integrating M ÷ EI twice: 0.1789 in against 0.4 in allowed at L/360
  7. σ = M ÷ S = 48,400 lb·in ÷ 63.28 in³ = 764.8 psi
  8. S needed = M ÷ Fb′ = 48,400 lb·in ÷ 900 psi = 53.78 in³
  9. Maximum bending moment at x = 4.667 ft: 4,033 lb·ft Sagging
Passes Bending and Deflection
Checks bending stress and deflection only. Shear, bearing at the supports, and lateral bracing of steel or deep wood beams still need their own checks.

How the Beam Load Calculator Works

Choose a support type, enter the span, then add the loads with every position measured from support A at the left end. The beam load calculator accepts a full-span uniform load, up to three point loads, one partial load that can taper from start to end, and one applied moment.

A negative load is treated as uplift, so wind suction or a hold-down force can be modeled on the same beam. Four supports are built in: simply supported, cantilever fixed at A, fixed at both ends, and fixed at A with a pin at B.

The section list covers single and built-up 2x lumber, 4x lumber, any rectangle, an I-beam or H-beam from its flange and web sizes, round pipe or bar, rectangular HSS tube, or any shape whose I and S you already know.

Materials include Douglas Fir-Larch No.2, Glulam 24F-V4, A36 and A992 steel, or your own E and Fb. For wood, a load duration setting adjusts the allowable stress for dead, floor, snow, construction or wind loads.

Results go well past support reactions. You get the maximum bending moment with its location and whether it sags or hogs, the bending stress against the allowable value, the section modulus needed, the maximum safe load, and the deflection checked against L/180 to L/480. Shear, moment and deflection diagrams, a table of values every L/10, a safe uniform load chart for the chosen section, and a step-by-step solution sit below the cards.

Turning Floor Loads Into Beam Load

Most beam loads start as pressure on a floor or roof in pounds per square foot. A beam carries the strip of floor halfway to the next support on each side, called its tributary width. Multiply that width by the psf load to get the uniform load in pounds per foot for the beam load calculator.

A beam under joists that span 8 ft on each side has a tributary width of 8 ft. With a 40 psf live load and a 10 psf dead load, the beam takes 8 × (40 + 10) = 400 lb/ft. The table shows common loads on that same 8 ft strip.

Load SourceArea LoadLine Load, 8 ft Tributary
Living areas, live load (IRC)40 psf320 lb/ft
Sleeping rooms, live load (IRC)30 psf240 lb/ft
Decks, live load (IRC)40 psf320 lb/ft
Wood floor framing, common dead load10 psf80 lb/ft
6 in concrete slab at 150 lb/ft³75 psf600 lb/ft

Residential live loads come from IRC Table R301.5. A concrete slab is pure dead load, which is why a slab bearing on a beam usually outweighs the people on it. Point loads such as a post from the floor above go in as P₁ to P₃ at their real positions.

Support Reactions From Equilibrium

For a simply supported beam, two equations give both reactions. Moments about A must sum to zero, and vertical forces must sum to zero. Each load F at distance x from A adds F × x to the moment sum.

The default beam spans 12 ft with 150 lb/ft along its full length and a 600 lb point load 4 ft from A. The uniform load totals 1,800 lb acting at 6 ft, so the moment of all loads about A is 1,800 × 6 + 600 × 4 = 13,200 lb·ft.

That gives R_B = 13,200 / 12 = 1,100 lb and R_A = 2,400 - 1,100 = 1,300 lb. Shear drops to zero at 4.667 ft from A, where the maximum moment is 4,033 lb·ft. The larger reaction, 1,300 lb, is also the largest shear the beam carries and the load the post at A must take down.

Those reactions feed the next checks down the load path. The Bearing Pressure Calculator checks a footing under the post against soil capacity, and the Ground Pressure Calculator converts a load and contact area into pressure.

Bending Stress and Safe Load

Bending stress is the moment divided by the section modulus S. In the default (2) 2x12 beam, S is 63.3 in³ and the moment is 4,033 lb·ft, or 48,400 lb·in.

Douglas Fir-Larch No.2 has a reference Fb of 900 psi in the NDS Supplement, so the beam runs at 85.0% of its allowable stress. The section modulus needed is 48,400 / 900 = 53.8 in³. The Bending Stress Calculator handles this check alone if you already know the moment.

The Max Safe Total Load card scales every load up together until the beam reaches its limit. Here bending stops it at 2,824 lb total, while L/360 deflection would allow 5,367 lb. That one number answers how much load a beam can carry in the same layout you entered.

Wood allowable stress is adjusted from the reference value. The tool works out Fb′ as Fb × C_D × C_F × C_V and shows each factor in the step-by-step solution. Beam stability stays at 1.0, which fits a beam braced along its top by the floor or roof above.

Sawn lumber gets a size factor C_F that rewards narrower boards. The beam load calculator applies these NDS Table 4A values to its lumber presets and to any rectangle up to 3.5 in wide, so a 2x14 entered as a rectangle gets 0.9. A member 5 in or wider is a timber, and the tool asks you to enter the Beams and Stringers values from Table 4D instead.

DF-L No.2 SizeSize Factor CFAllowable Fb′
2x61.31,170 psi
2x81.21,080 psi
2x101.1990 psi
2x121.0900 psi
4x81.31,170 psi
4x101.21,080 psi
2x140.9810 psi
4x121.1990 psi

The load duration factor C_D rises for loads that act briefly, since wood carries a short load better than a permanent one. Pick the shortest-duration load in the combination you are checking. The values below come from the NDS, with Fb′ shown for the default (2) 2x12.

Load DurationC_DFb′, (2) 2x12 DF-L No.2
Permanent, dead load only0.9810 psi
Floor live load1.0900 psi
Snow load1.151,035 psi
Construction load1.251,125 psi
Wind or earthquake1.61,440 psi

Set the default beam to snow load and its safe total load rises from 2,824 lb to 3,248 lb, since the stress ratio drops from 85.0% to 73.9%. Deflection does not change with C_D, because the factor applies to strength and not to stiffness.

Glulam 24F-V4 uses Fb = 2,400 psi and E = 1,800,000 psi, with a volume factor C_V for large members. Deep or long glulam beams lose some bending strength, and C_V follows NDS 5.3.6 with L in feet and b and d in inches.

A 5-1/8 x 24 in glulam over 30 ft gets C_V = 0.965 × 0.933 × 1.0 = 0.900, so its Fb′ drops to 2,161 psi. The safe uniform load chart in the tool works out C_V again for each span it lists.

Steel presets use an allowable stress of 0.66 Fy, which is 23,760 psi for A36 and 33,000 psi for A992. That value fits a compact section braced against sideways buckling, and the load duration setting is hidden for steel since it applies to wood only.

Wood Beam Load Capacity Chart

This chart shows the safe uniform load for common DF-L No.2 lumber beams on a simple span. Each value is the lesser of the bending limit and the L/360 deflection limit, and the beam's own weight is part of the load shown. Bending governs every value here, at a load duration factor of 1.0 for floor live load. Under snow load most values rise by 15%, but 2x10 sections at 16 ft become deflection-limited and gain less.

Section8 ft10 ft12 ft14 ft16 ft
2x10221 lb/ft141 lb/ft98 lb/ft72 lb/ft55 lb/ft
2x12297 lb/ft190 lb/ft132 lb/ft97 lb/ft74 lb/ft
(2) 2x10441 lb/ft282 lb/ft196 lb/ft144 lb/ft110 lb/ft
(2) 2x12593 lb/ft380 lb/ft264 lb/ft194 lb/ft148 lb/ft
(3) 2x12890 lb/ft570 lb/ft396 lb/ft291 lb/ft222 lb/ft
4x12761 lb/ft487 lb/ft338 lb/ft249 lb/ft190 lb/ft

Compare these with the floor loads above. A (2) 2x12 on 12 ft holds 264 lb/ft, but a 6 ft tributary strip at 40 psf live plus 10 psf dead puts 300 lb/ft on it, so it needs a third ply or a shorter span. Pick your section in the beam load calculator and open Safe Uniform Load by Span for the same chart at 4 to 30 ft.

For lumber spans checked against joist span tables, the Wood Beam Span Calculator and Floor Joist Calculator give the framing side of the same question.

Steel I-Beam Load Capacity Chart

Steel W-shapes are the usual answer for 20 to 40 ft spans. The chart lists the safe uniform load on a simple span for A992 steel at 0.66 Fy, with deflection held to L/360 under the full load. Ix and Sx come from the AISC shapes database.

W-ShapeIx / Sx20 ft Span30 ft Span40 ft Span
W8x1861.9 in⁴ / 15.2 in³332 lb/ft98 lb/ft42 lb/ft
W10x26144 in⁴ / 27.9 in³773 lb/ft229 lb/ft97 lb/ft
W12x26204 in⁴ / 33.4 in³1,096 lb/ft325 lb/ft137 lb/ft
W14x30291 in⁴ / 42.0 in³1,563 lb/ft463 lb/ft195 lb/ft
W16x31375 in⁴ / 47.2 in³2,014 lb/ft597 lb/ft252 lb/ft
W18x35510 in⁴ / 57.6 in³2,739 lb/ft812 lb/ft342 lb/ft
W21x44843 in⁴ / 81.6 in³4,488 lb/ft1,341 lb/ft566 lb/ft
W24x551,350 in⁴ / 114 in³6,270 lb/ft2,148 lb/ft906 lb/ft

Deflection governs almost every steel value, so stiffness rather than strength sizes long spans. A beam that spans 40 ft under a 400 lb/ft floor load needs a W21x44 or larger, while the same load over 20 ft fits a W10x26. Since IBC floors use L/360 under live load only, these charts are on the safe side when dead load is large.

For an H-beam or any I-shape not listed, pick I-Beam or H-Beam and enter the depth, flange width, flange thickness and web thickness. Or choose I and S Known and type the values from a steel table, which works for any steel beam load calculator check.

Support Type and Beam Formulas

The same load can produce very different moments depending on how the ends are held. A cantilever under uniform load sees wL²/2, four times the wL²/8 of a simple beam, and all of it at the wall. Fixing both ends cuts the peak to wL²/12, but that moment sits at the supports and puts the top of the beam in tension.

CaseMax MomentMax ShearMax Deflection
Simply supported, uniform wwL²/8wL/25wL⁴/384EI
Simply supported, center PPL/4P/2PL³/48EI
Cantilever, uniform wwL²/2wLwL⁴/8EI
Cantilever, end PPLPPL³/3EI
Fixed both ends, uniform wwL²/12wL/2wL⁴/384EI
Fixed both ends, center PPL/8P/2PL³/192EI
Fixed-pinned, uniform wwL²/85wL/8wL⁴/185EI
Fixed-pinned, center P3PL/1611P/16PL³/107.3EI

These closed forms cover single loads only. With mixed loads, the simple beam load calculator mode and the other three modes solve the full beam instead, so off-center point loads and partial loads land at their true peak. Deflection is found by integrating M / EI along the span, and the Beam Deflection Calculator adds limit tables, minimum I and lightest-section sizing for the same beam.

Hoist Beams and Uplift

An I-beam used for a hoist or trolley carries a moving point load. Run the beam load calculator twice, once with the hoist load at midspan for peak moment and once next to a support for the peak reaction. Include the hoist and trolley weight with the rated load.

Hoist beams also need checks the tool does not run, such as local bending of the bottom flange under the trolley wheels and an impact allowance for lifting. Treat the result as a first sizing step and confirm it with the hoist maker's beam requirements.

Uplift works the same way in reverse. Enter wind suction or a tie-down force as a negative load, and the tool shows a negative reaction when a support must hold the beam down. The alert flags it, so that connection can be designed to resist uplift.

Beam Self-Weight

Self-weight is the cross-section area times the material density. Steel at 490 lb/ft³ weighs about 3.4 lb/ft for every square inch of area, and a W-shape name already gives its weight, so a W8x18 is 18 lb/ft. A 10 ft W8x18 weighs 180 lb and a 20 ft W8x18 weighs 360 lb.

In metric units, steel at 7,850 kg/m³ weighs 0.785 kg/m for each cm² of area. The tool uses 35 lb/ft³ for Douglas fir and glulam, so a (2) 2x12 adds about 8.2 lb/ft. Turn Beam Self-Weight on and the tool adds it to every check. Full steel weights by shape and length are in the Steel Weight Calculator.

Beam Load FAQs

These answers cover the beam load questions people ask most, with numbers you can reproduce in the calculator.

How do I calculate what size beam I need?

Find the maximum moment, divide it by the allowable stress to get the section modulus needed, then check deflection. For a 12 ft simple span carrying 300 lb/ft, M = 300 × 12² / 8 = 5,400 lb·ft, or 64,800 lb·in. At Fb = 900 psi, the beam needs S = 72 in³.

A (2) 2x12 has S = 63.3 in³ and fails, while a (3) 2x12 has 94.9 in³ and passes. Its deflection is about 0.16 in, well inside the 0.40 in allowed at L/360. The beam load calculator shows Section Modulus Needed on the stress card so you can compare sizes quickly.

How much load can a beam carry?

It depends on span, section, material and support type, and span matters most. Safe uniform load from bending falls with the square of the span, so doubling the span cuts it to one quarter. A (2) 2x12 in DF-L No.2 carries 593 lb/ft over 8 ft but only 148 lb/ft over 16 ft.

Steel works the same way, though deflection usually governs before stress. Enter your loads and read the Max Safe Total Load card, which reports both limits and names the one that controls.

What is the formula for beam calculation?

The core formulas are equilibrium for reactions, M = wL²/8 or PL/4 for the peak moment on a simple span, σ = M/S for stress, and 5wL⁴/384EI or PL³/48EI for deflection. Each support type has its own set, listed in the table above.

For a 10 ft simple span under 200 lb/ft, R = 200 × 10 / 2 = 1,000 lb at each end and M = 200 × 10² / 8 = 2,500 lb·ft. Keep units consistent when you combine them, and convert lb/ft to lb/in before using inches for deflection.

How much weight can a 4 inch I-beam hold?

A 4 in I-beam is a small section, and its capacity drops fast with span. Look up its Ix and Sx in the AISC tables, choose I and S Known, and enter your span and load. For a quick check, use w = 8 × 0.66 Fy × S / L² for strength and the L/360 deflection formula for stiffness.

Light 3 in and 4 in I-beams are usually stiffness-limited past a few feet of span. If the Max Safe Total Load card names deflection as the limit, a deeper section helps far more than a heavier one of the same depth.

How do you calculate the weight of a 200x100 I-beam per meter?

Multiply the cross-section area in cm² by 0.785 to get kg per meter for steel. The area depends on the flange and web thicknesses, not only the 200 x 100 mm outline, so take it from the maker's section table for the exact shape, such as an ISMB or UB section.

For Indian sections, ISMB tables list the mass per meter directly. Enter that mass as a uniform load, or turn on self-weight with the I-Beam option and the tool works it out from the dimensions you enter.

How do you calculate load in kg?

Divide pounds by 2.2046 to get kilograms of mass, or multiply kilonewtons by 101.97. A 1,300 lb reaction equals about 590 kg, and a 10 kN load equals about 1,020 kg. The beam load calculator accepts loads in lbf, kips, N and kN, so you can enter metric loads directly.

Forces in N or kN are what the calculator expects for metric work. To enter a mass in kg as a load, multiply it by 9.81 to get newtons first.