Ramp Slope Calculator for wheelchair and access ramps: run from rise, slope from rise and run, or rise from run, with grade, angle, landings and handrails under US, AU or UK rules.
Rise is the height from the ground to the top step or landing.
Ramp Width
Used for the surface area to buy decking, plywood or concrete.
Ramp Side View
Ramp Slope Chart
| Slope | Grade | Angle | Run for 24 in Rise | Use |
|---|---|---|---|---|
| 1:4 | 25.00% | 14.04° | 8 ft | Too Steep |
| 1:6 | 16.67% | 9.46° | 12 ft | Too Steep |
| 1:8 | 12.50% | 7.13° | 16 ft | Too Steep |
| 1:10 | 10.00% | 5.71° | 20 ft | Too Steep |
| 1:12 | 8.33% | 4.76° | 24 ft | Ramp |
| 1:14 | 7.14% | 4.09° | 28 ft | Ramp |
| 1:16 | 6.25% | 3.58° | 32 ft | Ramp |
| 1:20 | 5.00% | 2.86° | 40 ft | Walkway |
Step-by-Step Ramp Math
- Run = rise × slope number = 24 in × 12 = 288 in
- Grade = rise ÷ run × 100 = 24 ÷ 288 × 100 = 8.33%
- Angle = arctan(rise ÷ run) = arctan(0.0833333) = 4.76°
- Sloped surface = √(rise² + run²) = √(24² + 288²) = 288.9983 in
- Result = 24 ft Ramp Run
Ramp Slope Calculator Runs for Common Rises
A wheelchair ramp at the 1:12 limit needs 1 ft of level run for every inch of rise, so a 24 in rise needs 24 ft. Gentler slopes stretch that run, and above 30 in the ramp must split into two runs with a level landing between.
In ramp slope calculator math, L is the horizontal run, R is the vertical rise and n is the second number in the 1:n slope ratio. Rise is measured from the ground to the top landing or doorway threshold, not to the first step.
| Rise | Run at 1:12 | Run at 1:16 | Run at 1:20 | Runs at 1:12 | Straight length with landings | Handrails |
|---|---|---|---|---|---|---|
| 6 in | 6 ft | 8 ft | 10 ft | 1 | 6 ft | Not required |
| 12 in | 12 ft | 16 ft | 20 ft | 1 | 12 ft | Both sides |
| 18 in | 18 ft | 24 ft | 30 ft | 1 | 18 ft | Both sides |
| 24 in | 24 ft | 32 ft | 40 ft | 1 | 24 ft | Both sides |
| 30 in | 30 ft | 40 ft | 50 ft | 1 | 30 ft | Both sides |
| 36 in | 36 ft | 48 ft | 60 ft | 2 | 41 ft | Both sides |
| 48 in | 48 ft | 64 ft | 80 ft | 2 | 53 ft | Both sides |
| 60 in | 60 ft | 80 ft | 100 ft | 2 | 65 ft | Both sides |
The straight length adds one 60 in level landing between runs, which most ramp slope calculator answers leave out. A 36 in rise is 36 ft of sloped run but 41 ft of ground, before the top and bottom landings are added.
A switchback or L-shaped layout folds those runs back on themselves when the yard is short. Each turn needs a landing at least 60 in by 60 in, so a ramp slope calculator run total is only part of the space the ramp takes up.
Landings, Handrails and the 30 Inch Rise Cap
Under the 2010 ADA Standards, which set US ramp slope calculator limits, one ramp run may climb no more than 30 in, and handrails are needed on both sides once the rise passes 6 in. The US Access Board guide to ramps sets out each limit by section.
| Rule | US limit | Section |
|---|---|---|
| Running slope | 1:12 (8.33%) maximum | 405.2 |
| Cross slope | 1:48 (2.08%) maximum | 405.3 |
| Clear width | 36 in minimum between handrails | 405.5 |
| Rise per run | 30 in maximum, no limit on runs | 405.6 |
| Landings | Top and bottom of each run; 60 in long | 405.7 |
| Handrails | Both sides when rise is over 6 in | 405.8 |
Altered buildings with no room for 1:12 get two short exceptions. A slope up to 1:10 may climb 6 in, which takes 5 ft of run instead of 6 ft, and a slope up to 1:8 may climb 3 in over 2 ft instead of 3 ft.
Those exceptions save at most 12 in of length, so they suit a single step at an old doorway and nothing larger. New work runs every ramp slope calculator figure at 1:12 or gentler.
A route flatter than 1:20, or 5%, is a walking surface rather than a ramp, so ramp handrail rules stop applying. The approach walk still needs a gentle cross slope, which the Sidewalk Slope Calculator works out.
Australia and UK Ramp Gradient Rules
Australia caps a wheelchair ramp at 1:14, not 1:12, so the same rise needs about 17% more run in a ramp slope calculator in meters than at the US limit. A 450 mm rise takes 6.3 m at 1:14 against 5.4 m at the US 1:12 limit.
| Rise | Run at 1:14 | Runs at 1:14 (landing every 9 m) | Run at 1:20 | Runs at 1:20 (landing every 15 m) |
|---|---|---|---|---|
| 150 mm | 2,100 mm | 1 | 3,000 mm | 1 |
| 300 mm | 4,200 mm | 1 | 6,000 mm | 1 |
| 450 mm | 6,300 mm | 1 | 9,000 mm | 1 |
| 600 mm | 8,400 mm | 1 | 12,000 mm | 1 |
| 900 mm | 12,600 mm | 2 | 18,000 mm | 2 |
Landing spacing, 1000 mm clear between handrails, and handrails with kerbs on both sides follow the Australian Network on Disability Design for Dignity guidelines, the basis of a ramp slope calculator australia check.
A step ramp may be as steep as 1:10 when it rises no more than 190 mm over no more than 1900 mm. That suits a single threshold; anything higher drops back to the 1:14 rule and its 2,660 mm run for the same 190 mm.
The Department of Veterans' Affairs ramp guidance for home modifications adds a 1200 mm overall ramp width and handrails 865 to 1000 mm above the surface, with a 300 mm extension past each end.
In the UK, Approved Document M ties the allowed gradient to the length of each going, so a UK ramp slope calculator answer depends on both. Building control body LABC cites a shop floor 500 mm up needing a 1:20 ramp about 10 m long, 1.5 m wide.
Steeper UK gradients are allowed only over shorter goings, from 1:20 over 10 m down to 1:12 over 2 m. The Approved Document M table on Designing Buildings steps one ratio number per metre of going.
| Longest going | Steepest gradient | Most rise |
|---|---|---|
| 10 m | 1:20 | 500 mm |
| 8 m | 1:18 | 444 mm |
| 6 m | 1:16 | 375 mm |
| 5 m | 1:15 | 333 mm |
| 4 m | 1:14 | 285 mm |
| 3 m | 1:13 | 230 mm |
| 2 m | 1:12 | 166 mm |
A 500 mm rise fits one 1:20 flight, but at 1:12 it needs three 2 m flights with landings between. UK ramps also need level landings at least 1.2 m long at the foot and head, clear of any door swing.
One to 30 Percent Ramp Slopes as Ratios
An 8.33% grade is 1:12, and every slope steeper than that fails the US wheelchair limit. The table converts 1 to 30 percent ramp slope figures into ratios, angles and rise per foot of run.
| Grade | Ratio | Angle | Rise per foot | US use |
|---|---|---|---|---|
| 1% | 1:100 | 0.57° | 0.12 in | Walkway |
| 2% | 1:50 | 1.15° | 0.24 in | Walkway |
| 5% | 1:20 | 2.86° | 0.60 in | Walkway limit |
| 6.25% | 1:16 | 3.58° | 0.75 in | Ramp |
| 7.14% | 1:14 | 4.09° | 0.86 in | Ramp (Australian limit) |
| 8.33% | 1:12 | 4.76° | 1.00 in | US ramp limit |
| 10% | 1:10 | 5.71° | 1.20 in | Altered sites, 6 in rise |
| 12.5% | 1:8 | 7.13° | 1.50 in | Altered sites, 3 in rise |
| 16.67% | 1:6 | 9.46° | 2.00 in | Too steep |
| 20% | 1:5 | 11.31° | 2.40 in | Too steep |
| 25% | 1:4 | 14.04° | 3.00 in | Too steep |
| 30% | 1:3.33 | 16.70° | 3.60 in | Too steep |
A ramp slope calculator in percentage and a ratio carry the same number. Divide 100 by the grade to get the second ratio number, so 6.25% gives 1:16 and 4% gives 1:25.
The Access Board recommends using the least slope possible below 1:12 for easier use. In ramp slope calculator terms, going from 1:12 to 1:16 on a 24 in rise costs 8 ft more run, which is the trade the table above prices out.
Surface Length and Area to Order
The sloped surface in a ramp slope calculator result is only slightly longer than the run, about 1 in per 24 ft at 1:12. Decking, plywood, non-slip coating and concrete forms are bought by that surface length times the clear width.
S is the sloped surface length, R is the rise and L is the level run, all in the same unit. Multiply S by the ramp width for the surface area, then add each landing on top.
| Rise and slope | Width | Run | Sloped surface | Surface area |
|---|---|---|---|---|
| 24 in at 1:12 | 36 in | 24 ft | 24 ft 1 in | 72.2 sq ft |
| 30 in at 1:12 | 48 in | 30 ft | 30 ft 1¼ in | 120.4 sq ft |
| 18 in at 1:16 | 42 in | 24 ft | 24 ft ½ in | 84.2 sq ft |
| 12 in at 1:20 | 36 in | 20 ft | 20 ft ¼ in | 60.1 sq ft |
| 500 mm at 1:14 | 1.2 m | 7.0 m | 7.02 m | 8.42 m² |
The width in a ramp slope calculator area figure is the clear space between handrails, so the deck itself runs wider by the rail posts. For a concrete ramp slope calculator estimate, the same surface area times slab thickness gives the pour volume.
Measure the real rise before ordering, since a threshold read as 24 in that turns out to be 27 in adds 3 ft of run at 1:12, and the Elevation Grade Calculator works out the grade of the ground the ramp sits on.
Steeper Slopes for Loading and Short Rises
Slopes steeper than 1:12 are not for a person driving or pushing their own chair. Ramp maker EZ-ACCESS lists 1:8 and 1:6 for equipment loading, and 1:6 suits a chair only with a helper pushing.
| Slope | Run for a 36 in rise | Angle | Typical use |
|---|---|---|---|
| 1:4 | 12 ft | 14.04° | Empty chair or cargo loading |
| 1:6 | 18 ft | 9.46° | Helper pushing the chair, or loading |
| 1:8 | 24 ft | 7.13° | Loading, or 3 in max rise at altered sites |
| 1:12 | 36 ft in two runs | 4.76° | US wheelchair ramp |
A 36 in van or truck bed shows how far apart loading and ramp slope calculator figures sit. At 1:4 the ramp is 12 ft, while a person in a chair needs 36 ft of run at 1:12, split into two runs with a landing.
A ramp slope calculator for car or garage use falls outside these wheelchair rules entirely. Check the vehicle's ground clearance and the driveway rules of the local building department instead.
Common Ramp Ratio Answers
Each answer below uses the same three numbers, the rise, the level run and the ratio between them, kept in one unit before dividing.
How do I calculate the slope of a ramp?
Divide the level run by the rise to get the ratio, or divide the rise by the run and multiply by 100 for a percent. A 20 in rise over 20 ft (240 in) of run is 240 ÷ 20 = 12, so 1:12, which is 8.33% or 4.76°.
Measure the run level, not along the sloped surface, and measure the rise from the ground at the bottom to the finished top landing. The ratio comes first, then the percent, then the angle, which is the order of any ramp slope calculator with steps.
What is the slope ratio for a wheelchair ramp?
The US maximum is 1:12, Australia's is 1:14, and the UK allows 1:20 over a 10 m going, up to 1:12 over a 2 m going. Any slope gentler than the limit is allowed, and it costs only extra run length.
For a 30 in rise, those choices mean 30 ft at 1:12, 35 ft at 1:14 and 50 ft at 1:20. For a ramp slope calculator for wheelchair planning, choose the slope first and let the run follow.
What is the 1/12 rule for ramps?
The 1/12 rule means 1 unit of rise for every 12 units of level run, so 1 in of drop every 12 in. That equals 1 in per foot, an 8.33% grade and a 4.76° angle.
A 27 in porch needs 27 ft of run under the rule, and the sloped deck is 27 ft 1⅛ in long. In metric the same 1:12 rule turns a 450 mm rise into 5,400 mm of run.
Which is steeper, 1 12 or 1 20?
A 1:12 slope is steeper. It rises 1 unit in 12, an 8.33% grade, while 1:20 rises 1 unit in 20, a 5% grade, so for a 24 in rise the run grows from 24 ft at 1:12 to 40 ft at 1:20.
A 1 in 20 slope also marks the line where a path stops being a ramp under US rules. At 5% or flatter the route is a walking surface, so ramp handrails and the 30 in rise cap no longer apply.
How to calculate 12% slope?
A 12% slope rises 12 units for every 100 units of level run, which is 1:8.33 and 6.84°. Rise equals run times 0.12, so 10 ft of run climbs 14.4 in, and run equals rise divided by 0.12.
An 18 in rise at 12% needs 150 in, or 12 ft 6 in, of run. That is steeper than the 1:12 wheelchair limit, so a ramp slope calculator check puts the same rise at 18 ft of run to pass.
How do you calculate ramp length?
Multiply the rise by the ratio number for the level run, then use the square root of rise squared plus run squared for the sloped length. A 450 mm rise at 1:12 gives 5,400 mm of run and 5,419 mm of sloped surface.
Calculate length of a ramp in the same unit throughout, and add every landing to the total footprint. A 48 in rise at 1:12 is 48 ft of run but needs 53 ft in a straight line once its middle landing is in.