Asphalt Compaction Calculator

Asphalt Compaction Calculator math links loose and rolled lift depth through roll-down, checks the lift depth against stone size and turns core Gmb and Gmm into percent compaction.

Quick Setup

Hot mix usually rolls down about 20% of its loose thickness.

% Gmm
%
Area, Density and Mix Size24 × 20 ft, 9.5 mm mix
%
Compacted Asphalt Thickness
2 in Compacted Thickness
Exact 2.000 in · from 2 1/2 in loose after 20% roll-down
1/2 in Roll-Down
Weight per Sq Yd218 lb
Sq Ft per Ton82.8 sq ft
How far the mat drops under the roller, the rolled weight per unit of area, and the area one ton covers.
Thick Enough for This Mix
Fine Mix Minimum1 1/8 in
Coarse Mix Minimum1 1/2 in
Compacted lift thickness checked against the mix’s nominal stone size. Fine mixes need at least three times it, coarse mixes four.
6.09 Tons of Hot Mix
Compacted Volume3.11 cu yd
Loose Volume Laid3.89 cu yd
Hot mix tonnage for the area and density in the options. Weight stays the same from loose mat to rolled pavement.
13.79 cu ft per Ton
Cu Yd per Ton0.511
20-Ton Load Covers1,655 sq ft
The space one ton of rolled asphalt fills, and how much area a full 20-ton truckload covers at this compacted thickness.
Loose vs Compacted Mat DiagramRolls down 1/2 in
Loose vs Compacted Asphalt ChartAt 20% reduction
CompactedLoose to LayRoll-DownAsphalt
1 in1 1/4 in1/4 in3.05 tons
1 1/2 in1 7/8 in3/8 in4.57 tons
2 in2 1/2 in1/2 in6.09 tons
2 1/2 in3 1/8 in5/8 in7.61 tons
3 in3 3/4 in3/4 in9.14 tons
4 in5 in1 in12.18 tons
5 in6 1/4 in1 1/4 in15.23 tons
6 in7 1/2 in1 1/2 in18.27 tons
Step-by-Step Asphalt Compaction MathYour numbers
  1. Reduction = 20% ÷ 100 = 0.2
  2. Area = 24 ft × 20 ft = 480.000 sq ft
  3. Tonnage = 480.000 sq ft × 0.166667 ft × 1.05 × 145 lb/ft³ = 12,180 lb ÷ 2,000 = 6.09 tons
  4. Compacted thickness = 2.5 in × (1 - 0.2) = 2 in (2 in)
Lift and Roll-Down Look Normal
Set the screed for 2 1/2 in loose to finish near 2 in. Confirm on a test strip, since roll-down changes with mix, temperature and rollers.

Roll-Down Math Behind an Asphalt Compaction Calculator

Dense-graded hot mix loses about 20% of its loose thickness under the rollers. A mat laid 2 1/2 in thick behind the paver finishes near 2 in, and 3 3/4 in loose finishes near 3 in.

That 20% comes from a screed rule published by Asphalt Institute engineers Danny Gierhart and Jason Wielinski. They set the screed at 1.25 times the final compacted thickness, and open-graded or gap-graded mixes use 15% instead.

C is compacted thickness, L is loose thickness and R is the roll-down as a decimal (0.20 for 20%). Run the other way, the asphalt compaction calculator formula solves for loose thickness.

The roll-down factor in any asphalt compaction calculator estimate comes from a test strip, measured before and after rolling. R equals loose minus compacted, divided by loose, so a strip that goes from 2.5 in to 2.0 in rolled down 0.5 ÷ 2.5, or 20%.

How do you calculate asphalt compacted thickness?

Multiply the loose thickness by one minus the roll-down. At the usual 20%, 3 in laid loose gives 3 × 0.80 = 2.4 in compacted, which a tape reads as 2 3/8 in.

Every asphalt compaction calculator answer rests on that single relationship. Loose depth, finished depth and roll-down are tied together, so any two of them fix the third, and the table shows how much the roll-down choice moves the result.

Loose depth laidCompacted at 15% roll-downCompacted at 20% roll-downCompacted at 25% roll-down
1 1/2 in1 1/4 in (1.275)1 1/4 in (1.200)1 1/8 in (1.125)
2 in1 3/4 in (1.700)1 5/8 in (1.600)1 1/2 in (1.500)
2 1/2 in2 1/8 in (2.125)2 in (2.000)1 7/8 in (1.875)
3 in2 1/2 in (2.550)2 3/8 in (2.400)2 1/4 in (2.250)
3 3/4 in3 1/4 in (3.188)3 in (3.000)2 7/8 in (2.813)
4 in3 3/8 in (3.400)3 1/4 in (3.200)3 in (3.000)
5 in4 1/4 in (4.250)4 in (4.000)3 3/4 in (3.750)

Two quick rules in circulation fail an asphalt compaction calculator check. One search summary puts roll-down near 10%, which means laying 3.33 in for a 3 in mat. At the real 20%, that mat finishes at 2.67 in, about 1/3 in thin.

The other rule says asphalt loses 25% of its thickness. Taken as 25% of the loose depth, a 3 in mat needs 4 in loose. Taken as 25% added to the finished depth, it needs 3 3/4 in, which matches the Asphalt Institute screed rule.

Screed Height for Common Driveway and Lot Lifts

Lay about 1/4 in of extra loose mix for every inch of finished pavement. A 2 in surface goes down at 2 1/2 in, a 3 in drive at 3 3/4 in, and a 6 in truck section at 7 1/2 in in total.

The table runs common finished depths through the 20% rule. Its asphalt compaction calculator square feet figures use a 24 by 20 ft driveway with 5% waste, and the tons follow finished depth only.

Compacted thicknessLoose depth to layRoll-downTons for 480 sq ft (5% waste)
1 in1 1/4 in1/4 in3.05
1 1/2 in1 7/8 in3/8 in4.57
2 in2 1/2 in1/2 in6.09
2 1/2 in3 1/8 in5/8 in7.61
3 in3 3/4 in3/4 in9.14
4 in5 in1 in12.18
5 in6 1/4 in1 1/4 in15.23
6 in7 1/2 in1 1/2 in18.27

Deep sections go down in more than one lift, each with its own asphalt compaction calculator lay depth. The Asphalt Institute caps lifts at 3 in under static steel-wheel rollers, while pneumatic and vibratory rollers can compact much thicker lifts.

Driveway crews work thinner. The Ontario Hot Mix Producers Association driveway guide limits each driveway lift to 2 in compacted, so a 3 in drive goes down as two 1 1/2 in lifts, each laid about 1 7/8 in loose.

What is a good thickness for asphalt?

A driveway needs 3 in of compacted asphalt over 4 in of gravel base, or 4 in full-depth on firm subgrade. Light-duty parking lots use 3 in over 6 in of base, and truck lots use 6 in over 3 in.

Those designs come from Tim Murphy's paving designs in Asphalt magazine, where full-depth versions run 4, 4 1/2 and 7 1/2 in. Each finished depth then becomes a lay depth in any asphalt compaction calculator for driveway work.

UseCompacted asphaltTotal loose to layTons per 1,000 sq ft (5% waste)
Driveway over 4 in base3 in3 3/4 in19.03
Driveway, full-depth4 in5 in25.38
Light-duty lot, full-depth4 1/2 in5 5/8 in28.55
Truck lot over 3 in base6 in7 1/2 in38.06
Truck lot, full-depth7 1/2 in9 3/8 in47.58

For the stone layer under those sections, the Gravel Driveway Calculator sizes base tons. The Asphalt Calculator adds gravel base and material cost to the same job.

Minimum Lift Thickness by Stone Size

A compacted lift must be at least three times the mix's nominal maximum aggregate size (NMAS) for fine-graded mixes and four times for coarse-graded ones. Thinner lifts leave stones bridging each other, and the mat won't reach density.

The same Asphalt Institute engineers give that 3× and 4× rule. The mix design names its NMAS, so check it against the finished depth before an asphalt compaction calculator result goes on the job sheet.

Mix NMASTypical useMinimum lift, fine-graded (3×)Minimum lift, coarse-graded (4×)
4.75 mm (No. 4)Fine surface1/2 in (0.561)3/4 in (0.748)
9.5 mm (3/8 in)Surface1 1/8 in (1.122)1 1/2 in (1.496)
12.5 mm (1/2 in)Surface1 1/2 in (1.476)2 in (1.969)
19 mm (3/4 in)Binder2 1/4 in (2.244)3 in (2.992)
25 mm (1 in)Base3 in (2.953)3 7/8 in (3.937)
37.5 mm (1 1/2 in)Base4 3/8 in (4.429)5 7/8 in (5.906)

An asphalt compaction calculator check on a 1 1/2 in overlay points to a 9.5 mm mix, or a fine-graded 12.5 mm mix at the very least. A coarse 12.5 mm surface laid at 1 1/2 in sits under its 2 in minimum and tends to stay open and permeable.

Lift depth also controls how long the mat stays hot enough to roll. Thin lifts lose heat fast, and the Asphalt Temperature Calculator estimates that rolling window from lift depth and air temperature.

Percent Compaction From Gmb and Gmm

Percent compaction is the core's bulk specific gravity (Gmb) divided by the mix's maximum theoretical specific gravity (Gmm), times 100. Air voids are what is left below 100%.

This density side of an asphalt compaction calculator is a separate job from roll-down. Roll-down sets the lay depth, while percent compaction tells whether the rollers did their work.

P is percent compaction, Gmb is the bulk specific gravity of a core or gauge reading, and Gmm is the specific gravity of the same mix with every air void removed, also called the Rice value.

How to calculate compaction of asphalt?

Divide the core Gmb by the Gmm from the same lot. A core at 2.36 over a Gmm of 2.50 is 2.36 ÷ 2.50 × 100 = 94.4% compaction, which leaves 5.6% air voids in the mat.

Some specs compare against lab density instead of Gmm. Divide percent of Gmm by 100 minus the design air voids, so that 94.4% core is 94.4 ÷ 96 = 98.3% of lab density at 4% design voids.

Design voids vary by mix. The FHWA demonstration mixes were designed at 3.5 to 4.1% voids, which moves the same core to 97.8 to 98.4% of lab density.

Specific gravity times 62.4 gives density in lb per cubic foot, so that core weighs about 147.3 lb per cubic foot. The table holds percent compaction for a 2.50 Gmm mix, the range an asphalt compaction calculator metric or US result usually falls in.

Percent compaction (of Gmm)Air voidsCore density (lb/ft³)Core density (kg/m³)
90%10%140.42,250
91%9%142.02,275
92%8%143.52,300
93%7%145.12,325
94%6%146.62,350
95%5%148.22,375
96%4%149.82,400
97%3%151.32,425
98%2%152.92,450

What is 95% compaction?

95% compaction means the rolled mat has reached 95% of the mix's maximum density and holds 5% air voids. On a 2.50 Gmm mix, a core needs a density of about 148.2 lb per cubic foot to hit it.

In soil work, 95% usually refers to a Proctor test, but asphalt density is measured against Gmm. Push much past 97% and trouble starts, since the Asphalt Institute warns that mixes below 3% air voids lack room for the binder to expand in hot weather.

Density Targets, Cores and Pavement Life

Each extra point of in-place density adds about 10% to pavement service life. That makes the jump from a 92% minimum to a 94% average worth roughly 20% more life on the same tons of mix.

How much compaction does asphalt pavement need?

Asphalt pavement needs at least 92% of Gmm, with 93 to 94% preferred after construction. The FHWA density report HIF-21-020 found DOT minimums of 92.0 to 93.0% across nine agencies.

The same report found 12 DOTs averaging 94.3% density. One state that raised its minimum from 91.0 to 92.0% cut its low results from 20.0% of tests to 5.7%.

The payoff comes from fewer air voids. NCAT research ties a 1% drop in air voids to 8.2 to 43.8% better fatigue life and 7.3 to 66.3% better rutting resistance, depending on mix.

In-place densityAir voidsService life vs 92%Low end of fatigue gain vs 92%
92%8%BaselineBaseline
93%7%+10%+8.2%
94%6%+20%+16.4%
95%5%+30%+24.6%

Those gains stack in a straight line only as a planning figure for asphalt compaction calculator results. NCAT calls the 10% per point conservative, and the fatigue column uses the low end of its 8.2 to 43.8% range.

How do you measure asphalt compaction?

Asphalt compaction is measured with cores cut from the finished mat, compared against Gmm from plant mix sampled in the same lot. FHWA found most DOTs cut 6 in cores and test every 250 to 500 tons.

Nuclear and non-nuclear gauges give faster readings but need a core correlation. In the FHWA demonstration report HIF-19-052, one state ran its gauge correlated to five cores.

Roll-down is checked separately, with a depth probe in the loose mat and again after the last roller pass. Any asphalt compaction calculator formula for lay depth depends on that test strip number, not on a printed average.

Tons and Coverage per Ton of Rolled Asphalt

One ton of compacted hot mix fills 13.79 cu ft, or 0.511 cubic yards, at 145 lb per cubic foot. At 2 in compacted that ton covers 82.8 sq ft, and the loose mix laid for it is 25% deeper but weighs the same.

How much volume is 1 ton of asphalt?

A US ton of rolled hot mix takes up 13.79 cu ft, or 0.511 cubic yards. A metric tonne at the matching 2,323 kg per cubic meter takes up 0.431 cubic meters.

That tonne covers 8.61 square meters at 50 mm compacted, or 5.74 square meters at 75 mm. Those are the figures behind an asphalt compaction calculator square meters result and any 1 ton asphalt m2 check.

How to calculate asphalt per ton?

Multiply area by compacted thickness in feet and by 145 lb per cubic foot, then divide by 2,000. A 24 by 20 ft drive at 2 in is 480 × 0.1667 × 145 ÷ 2,000 = 5.80 tons, or 6.09 tons with 5% waste.

T is US tons, A is area in square feet, C is compacted thickness in inches, D is density in lb per cubic foot and w is the waste allowance as a decimal. Asphalt compaction calculator tonnage always uses the compacted depth, never the loose depth.

Using loose depth by mistake over-orders by exactly the roll-down ratio. A 3 in drive figured at its 3 3/4 in lay depth comes out 25% heavy, or 2.28 extra tons on a 480 sq ft job with 5% waste.

How much is a 20 ton load of asphalt?

A 20-ton load of hot mix covers about 1,655 sq ft at 2 in compacted, or 1,103 sq ft at 3 in. That is 0.511 cubic yards per ton, or about 10.2 cubic yards of rolled pavement per load.

Compacted thicknessWeight per sq ydSq ft per tonSq yd per ton20-ton load covers
1 in109 lb165.518.43,310 sq ft
1 1/2 in163 lb110.312.32,207 sq ft
2 in218 lb82.89.21,655 sq ft
2 1/2 in272 lb66.27.41,324 sq ft
3 in326 lb55.26.11,103 sq ft
4 in435 lb41.44.6828 sq ft
6 in653 lb27.63.1552 sq ft

The weight per square yard column lines up with the 110 lb per square yard per inch spread rate those Asphalt Institute engineers plan with. Asphalt compaction calculator coverage figures leave out waste, so trim each by about 5% for edges and spill.

Metric loads work the same way. A 20-tonne load covers about 172 square meters at 50 mm compacted, and 115 square meters at 75 mm, which squares an asphalt compaction calculator for driveways in metric with a plant ticket.