Gravel Driveway Calculator

Updated

Gravel Driveway Calculator for the tons and cubic yards a drive needs from its length, width, depth and stone type, with layers, turnarounds, truck trips and a full delivered cost.

Quick Setup

Measure the driveway length and width, then pick the finished gravel depth.

%
Layer Build-Up
Price, Trucks and Slope10 cu yd trucks, $90.00 per load
per load
%
Gravel to Order
14.0 tons of Gravel
Covers 500 sq ft at 6 in deep, plus 12% for compaction
10.37 cu yd Loose Gravel
Yards per Ton0.74 cu yd
Rolled Volume in Place9.26 cu yd
Loose gravel the supplier delivers, how much of it makes up one ton or tonne, and the finished gravel once it is rolled.
2 Truck Loads
Yards per Load5.19 cu yd
Tons per Load7.00 tons
Dump truck trips to haul the order, using whichever runs out first: the bed volume or the legal payload.
$740.00 Gravel Driveway Cost
Gravel Only$560.00
Cost per sq ft$1.48
Gravel at your price plus a delivery fee for every truck load, and what the finished driveway costs per unit of area.
35.7 sq ft Covered per Ton
Tons per 100 ft of Length28.00 tons
Each Extra Inch Adds2.33 tons
Driveway area one ton or tonne of this gravel covers at your depth, and the weight needed for a set length of driveway.
Driveway Cross-Section Diagram1 layer
6 in, 14.0 tonsCrown 2 3/8 in at center6 in totalFirm, compacted subgrade
Gravel by Depth ChartCrushed Stone, 500 sq ft
DepthLoose VolumeWeightSq Ft per TonGravel Cost
2 in3.46 cu yd4.67 tons107.1$186.67
3 in5.19 cu yd7.00 tons71.4$280.00
4 in6.91 cu yd9.33 tons53.6$373.33
6 in10.37 cu yd14.0 tons35.7$560.00
8 in13.83 cu yd18.7 tons26.8$746.67
12 in20.74 cu yd28.0 tons17.9$1,120
Step-by-Step Gravel Driveway MathYour numbers
  1. Area = 50 ft × 10 ft = 500 sq ft
  2. Gravel: 500 sq ft × 6 in × 1.12 = 10.37 cu yd × 2,700 lb/cu yd = 14.0 tons
  3. Loads = larger of 10.37 cu yd ÷ 10.00 cu yd and 14.0 tons ÷ 15 tons, rounded up = 2
  4. Crown = 10 ft ÷ 2 × 4% = 2 3/8 in higher at the center
  5. Cost = $560.00 gravel + 2 × $90.00 delivery = $740.00
Gravel Order Ready
Crown the center 2 3/8 in above the edges so rain runs off, and roll the gravel firm before driving on it. Ask whether the supplier sells by the ton or the yard.

Gravel Driveway Calculator Math, From Square Feet to Tons

A 50 by 10 ft driveway 6 inches deep holds 9.26 cubic yards of stone in place. With a 12% allowance that becomes 10.37 cubic yards to order, or 14.0 tons of crushed stone at 2,700 lb per loose cubic yard.

V is the cubic yards to order, L and W are length and width in feet, D is depth in inches, and a is the compaction allowance in percent. Dividing by 27 turns cubic feet into cubic yards, the unit truck beds and gravel driveway calculator orders use.

T is short tons and ρ is the loose weight of the stone in pounds per cubic yard. Quarries usually bill by the ton, so the weight step sets the bill, not the volume.

The 12% allowance sits close to the gap between loose and bank weights for gravel in the Caterpillar tables, the volume lost when loose stone is rolled back to a dense state. A 10% figure would leave the 6 inch drive about 0.19 cubic yards short.

The 1.4 to 1.5 tons per yard figure in many quick answers fits pit run or sand and gravel better than crushed stone. On a 4 inch drive of the same size it gives 8.64 to 9.26 tons with no allowance, against 9.33 tons once 12% is added.

Trucks set the last line of the gravel driveway calculator math. The 10.37 yards overfill a 10 cu yd bed, so it takes 2 loads of 5.19 yards and 7.0 tons. A $90 fee per load lifts $560 of stone at $40 per ton to $740, or $1.48 per sq ft.

Tons per Cubic Yard for Five Driveway Stones

Crushed stone weighs 1.35 tons per loose cubic yard and pit run weighs 1.63, a 20% spread on the same hole. The gravel driveway calculator weights here follow the Caterpillar earthwork reference tables.

Stonelb per cu ydkg per m³Tons per cu ydCu yd per tonTons, 500 sq ft at 6 inSq ft per ton at 6 in
Crushed stone2,7001,6021.350.7414.0035.7
Gravel, 1/4 to 2 in2,8501,6911.430.7014.7833.8
Gravel, dry2,5501,5131.280.7813.2237.8
Gravel, pit run3,2501,9281.630.6216.8529.7
Sand and gravel2,9001,7211.450.6915.0433.3

Ten cubic yards of pit run weighs 16.25 tons, so a full 10-yard bed is over a 15-ton payload. The same bed of crushed stone weighs 13.5 tons and stays legal, which is why pit run orders often need more trips than their volume suggests.

A 3/4 inch crushed stone order uses the crushed stone row. For any gravel driveway calculator figure you plan to pay on, ask the quarry for its scale weight per yard, since moisture and gradation move the real number.

Depth From 2 to 12 Inches, and the 6 to 8 Inch Lift

Six inches is the default depth because it fills one proper lift. The Penn State Driving Surface Aggregate specification places the surface course in a single 6 to 8 inch loose lift.

That same spec compacts the lift to 95% of ASTM D698 with a vibratory roller of at least 10 tons, at optimum moisture or up to 2% below. The final compacted depth is left to the contract, because soft subgrade needs more base below it.

Loose depth is the finished depth times 1.12, so a 6 inch finish spreads 6.72 inches loose. Under 5.36 inches finished, the lift drops below 6 inches loose; over 7.14 inches it passes 8 and needs two lifts.

Gravel driveway calculator results for 500 sq ft of crushed stone at a 12% allowance, $40 per ton, $90 per load, a 10 cu yd bed and a 15-ton payload run as follows.

Finished depthLoose depthCu yd to orderTonsSq ft per tonLoadsDelivered cost
2 in2.24 in3.464.67107.11$276.67
3 in3.36 in5.197.0071.41$370.00
4 in4.48 in6.919.3353.61$463.33
6 in6.72 in10.3714.0035.72$740.00
8 in8.96 in13.8318.6726.82$926.67
12 in13.44 in20.7428.0017.93$1,390.00

The 2 to 4 inch rows suit a top-up over a sound, crowned base, not a new surface. At 8 inches finished the stone spreads 8.96 inches loose, past the lift, so it is spread and rolled in two passes.

One full 10-yard load over 500 sq ft reaches 5.79 inches finished at the 12% allowance, a 6.48 inch loose lift. That still meets the spec and saves the second $90 trip that a full 6 inches needs.

Each added inch over 500 sq ft costs 2.33 tons of crushed stone. That is the quick gravel driveway calculator check when one quote says 5 inches and another says 6.

Base, Middle and Top Courses in a Three-Layer Drive

In gravel driveway calculator terms, a 13 inch build over 500 sq ft, with 6 in of pit run, 4 in of 1/4 to 2 in gravel and 3 in of crushed stone, takes 22.47 cubic yards and 33.70 tons, more than twice the single 6 inch layer.

LayerStoneDepthCu ydTonsPrice per tonStone costLoads
BasePit run6 in10.3716.85$22$370.742
MiddleGravel, 1/4 to 2 in4 in6.919.85$35$344.811
TopCrushed stone3 in5.197.00$42$294.001
TotalThree stones13 in22.4733.70$29.95 average$1,009.564

Each stone comes from its own pile, so the trips add up per layer: two for the base and one each for the middle and top. Four trips at $90 bring the job to $1,369.56, or $2.74 per square foot.

Lumped into one order, 22.47 yards and 33.70 tons would suggest three trucks, so a layered gravel driveway calculator count runs one trip higher here. The base needs two trucks either way, by volume and by its 16.85 tons.

Coarse 1/4 to 2 in gravel belongs in the middle or base, not on top, since the surface stone should all pass a 1.5 inch screen. The 3 inch crushed stone top is a finish course over a rolled base, not a stand-alone lift.

Coverage for 1 Ton and 2 Tons of Gravel

One ton of crushed stone covers 53.6 sq ft at 4 inches once the 12% allowance is taken out, or 60 sq ft spread loose with no allowance. Two tons cover 107.1 sq ft at that depth.

C is square feet covered per ton, ρ is loose weight in lb per cubic yard, D is depth in inches and a is the allowance. Run backward, it is the gravel driveway calculator step for how far a delivered pile will spread.

Depth1 ton, with 12%2 tons, with 12%1 ton, no allowance
2 in107.1 sq ft214.3 sq ft120.0 sq ft
3 in71.4 sq ft142.9 sq ft80.0 sq ft
4 in53.6 sq ft107.1 sq ft60.0 sq ft
6 in35.7 sq ft71.4 sq ft40.0 sq ft

Two tons of crushed stone is about 1.48 cubic yards, or 40 cubic feet loose. That is a heap close to 4 by 4 ft and 2.5 ft high, and well past what a half-ton pickup should carry.

Heavier stone covers less per ton. At 6 inches with the 12% allowance, pit run covers 29.7 sq ft per ton and dry gravel covers 37.8, so the stone type changes a per-ton gravel driveway calculator answer by more than 25%.

Common Driveway Sizes: 500 sq ft, 1,000 sq ft and 100 ft Long

A 500 sq ft drive needs 14.0 tons of crushed stone at 6 inches, and a 1,000 sq ft drive needs 28.0 tons. All gravel driveway calculator prices below use $40 per ton, $90 per load and the 12% allowance.

DrivewayDepthCu yd to orderTonsLoadsDelivered cost
500 sq ft4 in6.919.331$463.33
500 sq ft6 in10.3714.002$740.00
1,000 sq ft (100 x 10 ft)4 in13.8318.672$926.67
1,000 sq ft (100 x 10 ft)6 in20.7428.003$1,390.00
100 x 12 ft4 in16.5922.402$1,076.00
100 x 12 ft6 in24.8933.603$1,614.00

For a 100 ft driveway, 10 ft wide, every inch of depth adds 4.67 tons. Widening the same drive from 10 to 12 ft adds 20% to the stone, 5.6 tons at 6 inches, but no extra truck.

The 1,000 sq ft drive at 6 inches is set by volume, not weight. Its 28 tons fit two 15-ton payloads, but 20.74 yards need three 10-yard beds, so a gravel driveway calculator for tons alone would miss a trip.

L-Shaped Drives, Turnarounds and Sloped Runs

An L-shaped drive is two rectangles added together in any gravel driveway calculator total. A 50 by 10 ft run with a 20 by 10 ft leg covers 700 sq ft and takes 14.52 cubic yards, or 19.6 tons at 6 inches, two trucks and $964 delivered.

A is the area of a round turnaround in square feet and D is its diameter in feet. A 40 ft circle is 1,256.6 sq ft, more than twice the 500 sq ft drive leading to it.

Adding that circle lifts the order to 36.43 cubic yards and 49.19 tons, four trucks and $2,327.43. Here the turnaround, not the lane, is the biggest line in the gravel driveway calculator total.

Ls is the length along the surface, L is the level plan length and R is the rise, all in feet. Plan measurements from a site map or survey are level lengths, so slope adds stone on top of them.

On a gravel driveway calculator for slope, the amount is small. A 50 ft drive that climbs 5 ft, a 10% grade, is 50.25 ft along the surface, 0.5% longer and only 0.07 tons more at 6 inches.

A 10 ft climb, a 20% grade, adds 1.98% to the length. Grade limits for a climb that steep sit in the Driveway Slope Calculator.

Stone Size That Locks Into a Driving Surface

A well-graded stone with a 1.5 inch top size and enough fines to bind is the better driving surface. The Penn State spec calls for 100% passing the 1.5 inch sieve, which sets that as the largest stone in the mix.

Clean, single-size stone has no fines to fill the gaps, so it stays loose and shifts under tires. It belongs below the surface as a base course, the slot 1/4 to 2 in gravel and pit run fill in a gravel driveway calculator layer plan.

For a metric gravel driveway calculator order, 20 mm gravel is close to 3/4 inch stone, and the 1.5 inch limit is about 38 mm. Moisture matters at placement too: the spec places stone at optimum moisture or up to 2% below so it compacts to 95%.

Cheapest Gravel by the Ton and by the Yard

At an equal price per ton, dry gravel is the cheapest driveway stone because it is the lightest. Over 500 sq ft at 6 inches it costs $528.89 at $40 per ton, while pit run at the same price costs $674.07.

Cyd is the cost per cubic yard placed, Pton is the quoted price per ton and ρ is the loose weight in pounds per cubic yard. It puts per-ton and per-yard quotes on one scale before any gravel driveway calculator cost is compared.

StoneCost per cu yd at $40 per ton500 sq ft at 6 in, $40 per ton500 sq ft at 6 in, $40 per cu yd
Gravel, dry$51.00$528.89$414.81
Crushed stone$54.00$560.00$414.81
Gravel, 1/4 to 2 in$57.00$591.11$414.81
Sand and gravel$58.00$601.48$414.81
Gravel, pit run$65.00$674.07$414.81

Priced by the yard, all five cost the same because the hole holds the same volume. A low ton price on heavy stone can still lose: pit run at $22 per ton is $35.75 per yard, against $54.00 for crushed stone at $40.

Layering cuts the blended price too. With pit run at $22, middle gravel at $35 and a 3 inch crushed stone top at $42, the three-layer build averages $29.95 per ton across all 33.70 tons.

Crown Height on a 10 or 12 ft Drive

A crown of 1/2 to 3/4 inch per foot, a 4% to 6% cross slope, sheds water off a gravel driveway in the Penn State spec. Below 4% puddles sit in the wheel tracks, and above 6% the drive gets hard to drive on.

In gravel driveway calculator math, the center rise is half the width times the cross slope. On the default 10 ft drive at 4%, the center sits 2 3/8 inches above the edges.

Drive widthCenter rise at 4%Center rise at 5%Center rise at 6%
10 ft2 3/8 in3 in3 5/8 in
12 ft2 7/8 in3 5/8 in4 3/8 in

Shaping the crown into the subgrade first keeps the stone depth even. Building it from stone alone on a flat base adds about 2.07 cubic yards to the gravel driveway calculator total for a 50 by 10 ft drive at 4%, or 2.80 tons of crushed stone.

Low spots and missing subgrade height are cheaper to fix with soil than with stone; the Fill Dirt Calculator and Cut and Fill Calculator size that grading before any stone arrives.

Metric Orders in Cubic Meters and Tonnes

A 15 by 3 m driveway at 15 cm holds 6.75 m³ in place, 7.56 m³ with a 12% allowance, and needs 12.11 tonnes of crushed stone at about 1,602 kg/m³.

M is tonnes, L and W are length and width in meters, D is depth in centimeters, a is the allowance in percent and ρ is loose density in kg/m³, taken from the gravel driveway calculator weight table above.

The 15 cm finish spreads 16.8 cm loose, inside the 15 to 20 cm lift. One tonne of crushed stone covers 3.72 m² at that depth, and the same metric steps apply to 20 mm stone, which sits in the crushed stone row.

Short Answers on Gravel Driveway Orders

Every answer below uses crushed stone at 2,700 lb per loose cubic yard and a 12% allowance, the same basis as the tables above.

What is a gravel driveway calculator?

A gravel driveway calculator is the area times depth math for stone, carried through to weight, truckloads and cost. The weight step matters because quarries bill by the ton and trucks are capped by payload.

Layers, turnarounds and slope all add to the same total, and a Concrete Driveway Cost Calculator estimate or an Asphalt Calculator Tons figure compares a paved option on the same drive.

How much gravel do I need for my driveway?

Multiply length by width by depth in feet, divide by 27, add 12% and multiply by the stone's tons per yard. A 12 by 40 ft drive at 6 inches needs 8.89 cubic yards in place, 9.96 to order and 13.44 tons of crushed stone.

That gravel driveway calculator order just fits one truck, at 9.96 yards in a 10-yard bed and 13.44 tons under a 15-ton payload. One more inch of depth would take it to 11.61 yards and a second truck.

How do you calculate cubic yards of gravel?

Find the cubic feet and divide by 27. A 30 by 12 ft parking pad at 6 inches is 180 cubic feet, or 6.67 cubic yards, then 7.47 cubic yards to order and 10.08 tons of crushed stone.