Deck joist span calculator for 2x6 to 2x12 joists by species, spacing and snow load, with the 2021 IRC cantilever limit by backspan, the smallest joist size and the stock to order.
Pick the lumber stamped on your joists; spans assume No. 2 grade, wet service.
Decking & Deck Width
Deck Joist Side View
Deck Joist Span Chart
| Joist Size | 12 in | 16 in | 24 in |
|---|---|---|---|
| 2×6 | 9 ft 11 in | 9 ft | 7 ft 7 in |
| 2×8 | 13 ft 1 in | 11 ft 10 in | 9 ft 8 in |
| 2×10 | 16 ft 2 in | 14 ft | 11 ft 5 in |
| 2×12 | 18 ft | 16 ft 6 in | 13 ft 6 in |
Maximum Cantilever Chart
| Joist Size | 4 ft | 6 ft | 8 ft | 10 ft | 12 ft | 14 ft | 16 ft | 18 ft |
|---|---|---|---|---|---|---|---|---|
| 2×6 | 1 ft | 1 ft 6 in | 1 ft 5 in | NP | NP | NP | NP | NP |
| 2×8 | 1 ft | 1 ft 6 in | 2 ft | 2 ft 6 in | 2 ft 3 in | NP | NP | NP |
| 2×10 | 1 ft | 1 ft 6 in | 2 ft | 2 ft 6 in | 3 ft | 3 ft 4 in | 3 ft 4 in | NP |
| 2×12 | 1 ft | 1 ft 6 in | 2 ft | 2 ft 6 in | 3 ft | 3 ft 6 in | 4 ft | 4 ft 1 in |
Joist Spacing for Decking
| Decking | Square, 2 Joists | Square, 3+ Joists | Diagonal, 2 Joists | Diagonal, 3+ Joists |
|---|---|---|---|---|
| 5/4 wood | 12 in | 16 in | 8 in | 12 in |
| 2× wood | 24 in | 24 in | 18 in | 24 in |
| Composite or PVC | Board maker's span chart | |||
Step-by-Step Joist Span Check
Species and Size in a Deck Joist Span Calculator
A 2×8 Southern Pine deck joist at 16 in on center spans 11 ft 10 in (3.61 m) under the 2021 IRC deck table, for a 40 psf live load and 10 psf dead load. The same 2×8 reaches 11 ft 1 in in Douglas fir and 10 ft 7 in in cedar.
| Joist at 16 in O.C. | Southern Pine | Douglas Fir-Larch, Hem-Fir, SPF | Redwood, Cedars, Ponderosa, Red Pine |
|---|---|---|---|
| 2×6 | 9 ft 0 in (2.74 m) | 8 ft 4 in | 8 ft 0 in |
| 2×8 | 11 ft 10 in (3.61 m) | 11 ft 1 in | 10 ft 7 in |
| 2×10 | 14 ft 0 in (4.27 m) | 13 ft 7 in | 13 ft 0 in |
| 2×12 | 16 ft 6 in (5.03 m) | 15 ft 9 in | 15 ft 1 in |
These deck joist span chart IRC values come from Table R507.6 for No. 2 lumber with wet service and incising reductions built in, as builder Mike Guertin explains in JLC. The Denton, Maryland 2021 deck guide prints the same Southern Pine row.
The rule of thumb that a joist at 16 in spans 1.5 times its depth in feet says 12 ft for a 2×8 and 15 ft for a 2×10. Both overshoot every species, by up to 2 ft for 2×10 cedar.
That is why a deck joist span calculator result should come from the code table rather than a depth ratio. The ratio only lands on the table at 2×6 Southern Pine, 9 ft 0 in.
Can I always use a bigger joist to increase span?
Only up to the 2×12, the deepest size in any deck joist span calculator table. It tops out at 16 ft 6 in at 16 in on center in Southern Pine and 18 ft 0 in at 12 in.
Past that the deck joist span calculator table ends, and the answer is a second beam that shortens the span rather than a deeper joist.
A bigger joist also stops helping the overhang at short backspans. With 12 ft behind the beam, a 2×10 and a 2×12 both allow exactly 3 ft of cantilever, so stepping up a size buys span, not overhang.
Snow Loads Cut Spans by Up to 17%
A 70 psf ground snow load drops the 2×8 Southern Pine joist at 16 in from 11 ft 10 in to 9 ft 10 in, a 17% loss. The 2021 code added rows for 50, 60 and 70 psf ground snow that an older 40 psf deck joist span calculator chart lacks, per JLC.
| Southern Pine at 16 in O.C. | 40 psf Live | 50 psf Snow | 60 psf Snow | 70 psf Snow |
|---|---|---|---|---|
| 2×6 | 9 ft 0 in | 8 ft 4 in | 7 ft 10 in | 7 ft 6 in |
| 2×8 | 11 ft 10 in | 11 ft 0 in | 10 ft 4 in | 9 ft 10 in |
| 2×10 | 14 ft 0 in | 13 ft 9 in | 12 ft 9 in | 11 ft 11 in |
| 2×12 | 16 ft 6 in | 16 ft 2 in | 15 ft 0 in | 14 ft 0 in |
At 50 psf the 2×10 and 2×12 lose only about 2%, while the 2×6 and 2×8 lose 7%. By 70 psf every size loses 15 to 17%, so a deck joist span calculator run at 40 psf in snow country leaves a 2×10 about 2 ft too long.
The kPa values for metric work are 1.92 kPa for the 40 psf live load and 2.39, 2.87 and 3.35 kPa for the three snow rows. Use the snow row whenever the site's ground snow load passes 40 psf.
Twelve-Foot Spans Need a 2×10 at 16 Inches
A 12 ft span is 101% of the 2×8 deck joist span calculator limit at 16 in, so the 2×8 fails by 2 in and a 2×10 is the smallest joist that works. The 2×10 carries it with 2 ft to spare in Southern Pine, or 1 ft in cedar.
| Span, Ledger to Beam | Southern Pine 12 in | Southern Pine 16 in | Southern Pine 24 in | Douglas Fir 16 in | Cedar 16 in |
|---|---|---|---|---|---|
| 8 ft | 2×6 | 2×6 | 2×8 | 2×6 | 2×6 |
| 10 ft | 2×8 | 2×8 | 2×10 | 2×8 | 2×8 |
| 12 ft | 2×8 | 2×10 | 2×12 | 2×10 | 2×10 |
| 14 ft | 2×10 | 2×10 | Add a beam | 2×12 | 2×12 |
| 16 ft | 2×10 | 2×12 | Add a beam | Add a beam | Add a beam |
| 18 ft | 2×12 | Add a beam | Add a beam | Add a beam | Add a beam |
Step up from a 2×8 to a 2×10 once the span passes 11 ft 10 in in Southern Pine, 11 ft 1 in in the fir group or 10 ft 7 in in cedar, at 16 in on center and 40 psf. Tighter 12 in spacing lets the 2×8 reach 13 ft 1 in instead.
Can I use 2×6 joists for a deck?
Yes, for short spans of up to 9 ft in Southern Pine at 16 in, or 8 ft in cedar, the 2×6 deck joist span limits.
A 2×6 at its full 9 ft span gets no cantilever at all, though, since the deck joist span calculator table lists none past an 8 ft backspan, and even at 8 ft it allows only 1 ft 5 in.
Spacing Trades Span for Joists and Decking Limits
Moving a 2×8 Southern Pine joist from 16 in to 12 in on center adds 1 ft 3 in to its deck joist span calculator limit, and 24 in spacing cuts it to 9 ft 8 in. Across a 16 ft wide deck, that is 17 joists at 12 in, 13 at 16 in and 9 at 24 in.
| Southern Pine | 12 in O.C. (17 joists) | 16 in O.C. (13 joists) | 24 in O.C. (9 joists) |
|---|---|---|---|
| 2×6 | 9 ft 11 in | 9 ft 0 in | 7 ft 7 in |
| 2×8 | 13 ft 1 in | 11 ft 10 in | 9 ft 8 in |
| 2×10 | 16 ft 2 in | 14 ft 0 in | 11 ft 5 in |
| 2×12 | 18 ft 0 in | 16 ft 6 in | 13 ft 6 in |
The decking, not the joist, often sets the spacing in a deck joist span calculator plan. A 2×10 that spans 11 ft 5 in at 24 in still needs joists at 16 in under 5/4 boards.
IRC Table R507.7 caps 5/4 wood boards laid square at 16 in when they cross three or more joists, so a 24 in deck joist spacing chart value only works under 2× boards.
| Decking | Square, 2 Joists | Square, 3+ Joists | Diagonal, 2 Joists | Diagonal, 3+ Joists |
|---|---|---|---|---|
| 5/4 wood | 12 in | 16 in | 8 in | 12 in |
| 2× wood | 24 in | 24 in | 18 in | 24 in |
| Composite or PVC | Board maker's span chart | |||
Diagonal boards need tighter joists because each board crosses them at an angle and spans farther between supports. Guertin notes that some synthetic decking makers ask for 12 in spacing when their boards run diagonally.
How many deck joists do I need?
Divide the deck width along the ledger by the spacing, round up and add one. A 16 ft wide deck at 16 in needs 13 joists, a 12 ft deck needs 10 and a 20 ft deck needs 16, with the end joists counted.
N is the number of joists, W is the deck width along the ledger in inches, s is the on-center spacing in inches, and the brackets mean round up to the next whole number.
Spacing changes fasteners more than boards. The 2021 code calls for two nails or two No. 8 screws per board at each joist, so a 16 ft board takes 26 screws at 16 in and 34 at 12 in. The Decking Calculator counts the boards themselves.
Cantilever Limits Shrink Before the Span Runs Out
A 2×8 Southern Pine joist can overhang its beam by 2 ft 6 in at a 10 ft backspan, then only 2 ft 3 in at 12 ft, and not at all past 12 ft. The old quarter-of-the-backspan rule would allow 3 ft at 12 ft, or 9 in more than the 2021 table.
| Backspan | 2×6 | 2×8 | 2×10 | 2×12 | Quarter Rule |
|---|---|---|---|---|---|
| 4 ft | 1 ft 0 in | 1 ft 0 in | 1 ft 0 in | 1 ft 0 in | 1 ft 0 in |
| 6 ft | 1 ft 6 in | 1 ft 6 in | 1 ft 6 in | 1 ft 6 in | 1 ft 6 in |
| 8 ft | 1 ft 5 in | 2 ft 0 in | 2 ft 0 in | 2 ft 0 in | 2 ft 0 in |
| 10 ft | Not permitted | 2 ft 6 in | 2 ft 6 in | 2 ft 6 in | 2 ft 6 in |
| 12 ft | Not permitted | 2 ft 3 in | 3 ft 0 in | 3 ft 0 in | 3 ft 0 in |
| 14 ft | Not permitted | Not permitted | 3 ft 4 in | 3 ft 6 in | 3 ft 6 in |
| 16 ft | Not permitted | Not permitted | 3 ft 4 in | 4 ft 0 in | 4 ft 0 in |
| 18 ft | Not permitted | Not permitted | Not permitted | 4 ft 1 in | 4 ft 6 in |
Values are Southern Pine at 40 psf. The 2018 code checked a quarter of the span against its table and took the lesser, while the 2021 code reads the cantilever straight from the table and allows interpolation between rows, per Guertin.
His interpolation example checks out here. A 2×10 with an 11 ft 5 in backspan sits between 2 ft 6 in and 3 ft 0 in, giving 2 ft 10 1/4 in of overhang, the same figure any deck joist span calculator should land on.
Spacing can open up a span the overhang cannot follow. A 2×8 at 12 in on center may span 13 ft 1 in, but the table lists no 2×8 cantilever past a 12 ft backspan, so a 13 ft 2×8 joist has to stop at the beam.
Do cantilevers count toward the span calculation?
No. The span runs from the ledger to the beam and is checked against the span table, while the overhang past the beam is checked separately against the cantilever row for that backspan.
In a deck joist span calculator check, a 12 ft span of 2×10 at 16 in with an 18 in overhang uses 86% of its 14 ft span and half of its 3 ft cantilever. The joist is still 13 ft 6 in long, which matters for the lumber order, not the span check.
Measuring Span and Ordering Joist Stock
Order the next even length that covers the deck joist span calculator span plus overhang. The 12 ft span with an 18 in cantilever needs 13 ft 6 in, so 14 ft stock, or 182 lineal feet for 13 joists across a 16 ft deck.
| Joist at 16 in, Southern Pine | Max Span | Max Cantilever at That Span | Joist Length | Stock to Order |
|---|---|---|---|---|
| 2×6 | 9 ft 0 in | Not permitted | 9 ft 0 in | 10 ft |
| 2×8 | 11 ft 10 in | 2 ft 3 1/4 in | 14 ft 1 1/4 in | 16 ft |
| 2×10 | 14 ft 0 in | 3 ft 4 in | 17 ft 4 in | 18 ft |
| 2×12 | 16 ft 6 in | 4 ft 0 1/4 in | 20 ft 6 1/4 in | Over 20 ft, splice over a beam |
A 2×8 at full span with no overhang fits 12 ft stock with 2 in to spare, which leaves no room for a bad end. With its full overhang it needs 16 ft stock, 208 lineal feet for 13 joists.
Buying one length up from the deck joist span calculator cut length leaves room to square the ends.
Is joist span measured center to center?
Guertin measures the span from hanger center to hanger center and the cantilever from the center of the beam. He suggests carrying the overhang out to the outer edge of the decking to stay conservative.
Joist spacing, by contrast, is measured center to center of the joists. A 16 in deck joist spacing chart value means 16 in from the middle of one joist to the middle of the next.
What joist spans should I consider before ordering deck lumber?
Check the longest span on the plan against the deck joist span calculator table for your species and load, then add the overhang. Spans just under a limit, like 11 ft 9 in on a 2×8, leave no margin if the beam lands 2 in farther out than drawn.
Hangers, Cedar, Hot Tubs and Floor Spans
Several common deck questions sit around the deck joist span calculator table rather than in it. Each answer below ties back to the same 2021 code tables and the Southern Pine 2×8 and 2×10 examples above.
Why are deck joist spans shorter than floor joist spans?
Floor joist tables leave out the wet service and incising factors, so they do not apply to decks, as Guertin points out. A 2×10 deck joist at 16 in spans 14 ft 0 in in Southern Pine.
A floor table value for the same 2×10 is not a valid deck span, even under a covered porch roof, since the deck joist span calculator tables assume the wood can get wet in service.
Is cedar structurally weaker than pressure treated pine?
For span, yes. Cedar and redwood sit in the lowest group, so a 2×8 at 16 in reaches 10 ft 7 in against 11 ft 10 in for treated Southern Pine, and a 2×12 falls 1 ft 5 in short.
Treatment itself is not a table input, so pressure-treated and untreated boards of the same species and grade share one row. In any deck joist span calculator lookup, the species group and No. 2 grade set the span.
What are joist hangers and do I need them?
Hangers are steel seats that carry a joist end at a ledger or flush beam. Joist ends need restraint against rolling, and Fine Homebuilding notes hangers and blocking must be at least 60% of the joist depth.
Rounded up to the next 1/8 in, that is 3 3/8 in for a 2×6, 4 3/8 in for a 2×8, 5 5/8 in for a 2×10 and 6 3/4 in for a 2×12. Joists sitting on top of a beam get blocking or a fastened rim instead of hangers at that end.
Does a hot tub change the joist span?
Yes. A hot tub is a concentrated load the 40 psf deck tables were not built for, and Fine Homebuilding notes the span tables do not cover it, so the framing under one needs an engineer rather than a deck joist span calculator lookup.
Do I need bearers under deck joists?
Every joist needs a support at each end, a ledger on the house or a beam, also called a bearer, at the far end of each deck joist span calculator span.
The beam is sized from its own IRC Table R507.5, and the Deck Post Spacing Calculator and Deck Footing Calculator carry the load down to the ground.