Gutter Slope Calculator

Updated

Gutter Slope Calculator finds the drop from the high end to the downspout, marks each hanger along the run, and checks an existing gutter against the 1/4 in per 10 ft fall minimum.

Quick Setup

Enter the full gutter length and the fall you want. A split layout slopes each side to its own downspout.

Hangers and Downspout SpotHangers 24 in apart
High End to Downspout
1.00 in Total Drop
25.4 mm · about 1 in on a tape
0.119° Gutter Angle
Percent Grade0.208%
Slope Ratio1 in 480
Your fall written as an angle, a percent grade and a slope ratio, so it matches any level or plan you check.
21 Hangers Needed
Drop per Hanger0.050 in
Drop per Foot0.0250 in
Hangers needed at your spacing over the full length, and how much lower each one sits than the one before it.
100% of Minimum Pitch
Drop at 1 in per 16 ft2.50 in
Short of the Ideal1.50 in
Englert asks for at least 1/4 in per 10 ft. Fine Homebuilding calls 1 in per 16 ft ideal for good flow.
0.50 in if Split in Half
Run per Side if Split20.0 ft
Downspouts if SplitOne at each end
What changes if the high point moves to the middle and each half drains to a downspout at its own end.
Gutter Layout DiagramAt one end
Fascia / drip edge (level)1.00 in drop40.0 ft runHigh point

Slope drawn exaggerated so the fall is visible.

Hanger Mark-Out Table21 hangers, full length
HangerFrom Left EndDrop Below High PointTape Mark
1, high point0 in0 in0 in
22 ft 0 in0.050 in1/16 in
34 ft 0 in0.100 in1/8 in
46 ft 0 in0.150 in1/8 in
58 ft 0 in0.200 in3/16 in
610 ft 0 in0.250 in1/4 in
712 ft 0 in0.300 in5/16 in
814 ft 0 in0.350 in3/8 in
916 ft 0 in0.400 in3/8 in
1018 ft 0 in0.450 in7/16 in
1120 ft 0 in0.500 in1/2 in
1222 ft 0 in0.550 in9/16 in
1324 ft 0 in0.600 in5/8 in
1426 ft 0 in0.650 in5/8 in
1528 ft 0 in0.700 in11/16 in
1630 ft 0 in0.750 in3/4 in
1732 ft 0 in0.800 in13/16 in
1834 ft 0 in0.850 in7/8 in
1936 ft 0 in0.900 in7/8 in
2038 ft 0 in0.950 in15/16 in
21, downspout40 ft 0 in1.000 in1 in
Drop at Common PitchesOver 40.0 ft
PitchGradeAngleDrop Over 40.0 ft
1/8 in per 10 ft0.104%0.060°0.50 in
1/4 in per 10 ft, Englert min.0.208%0.119°1.00 in
1/2 in per 10 ft0.417%0.239°2.00 in
1/16 in per ft (1 in per 16 ft), FHB ideal0.521%0.298°2.50 in
1/8 in per ft1.042%0.597°5.00 in
Step-by-Step MathDrop = run × pitch
  1. Run to the downspout = 40 ft, the full length
  2. Pitch as a ratio = 0.25 in ÷ 120 in = 0.00208333
  3. Gutter angle = atan(0.00208333) = 0.119°
  4. Drop = 40 ft × 12 in/ft × 0.00208333 = 1.00 in
Pitch Within the Usual Range
Snap a chalk line from the high end, tight under the drip edge, to a mark 1 in lower at the downspout, then set each hanger on that line.

What the Gutter Slope Calculator Works Out

The gutter slope calculator has two modes. Plan the Drop takes the run length, the pitch you want and the downspout layout, then gives the total drop from the high end to the downspout. Check mode works the other way. You enter the drop measured on a gutter that is already up, and it tells you the pitch that gutter really has.

Both modes show the pitch as an angle, a percent grade, a slope ratio and a fall per foot or meter. A level, a laser and a set of plans rarely use the same unit, so each one has its number ready. The hanger count and a mark-out table for every hanger come from the same entries.

Gutter Calculation Formula

Gutter drop is the run length times the pitch. The run is the distance from the high point to the downspout, not the full gutter length when water drains both ways. With the pitch entered in inches per 10 ft, the calculator first turns it into a plain ratio. Every other output is built from that ratio.

Here p is the pitch in inches per 10 ft, and 120 is the number of inches in 10 ft. A pitch of 1/4 in per 10 ft gives r = 0.25 / 120 = 0.00208. The grade, angle and slope ratio outputs all start from this one ratio.

D is the drop in inches and L is the run in feet. A 40 ft run at 1/4 in per 10 ft needs 40 x 12 x 0.00208 = 1.00 in of drop. That is the hero result the tool shows on load with its default 40 ft run and 1/4 in pitch.

For 1/4 in per 10 ft, the angle is 0.119 degrees. The same pitch is a 0.208% grade and a slope ratio of 1 in 480. For a gutter calculation spreadsheet, put the run in feet in column A and the pitch in inches per 10 ft in column B. Then =A2*B2/10 returns the drop in inches.

The angle comes from =DEGREES(ATAN(B2/120)) in the next column. The gutter slope calculator runs the same math and adds the hanger table, split layouts and the minimum check, which a spreadsheet would need extra columns to match.

Correct Slope for a Gutter

Englert, a gutter system maker, calls for at least 1/4 in of slope for every 10 ft of gutter. That is the minimum the calculator checks against. Fine Homebuilding says gutters should ideally fall 1 in per 16 ft. That equals 1/16 in per foot, or 5/8 in per 10 ft.

Fine Homebuilding also says 1/2 in over 20 ft will drain if there are no low spots. That is the same rate as the Englert minimum. Steeper is not always better. Englert warns a very steep gutter can rush water past the downspout in heavy rain, and Fine Homebuilding notes it looks crooked against a level fascia.

The gutter slope calculator flags anything under 1/4 in per 10 ft as too flat. Anything past 1 in per 16 ft is flagged as steeper than the usual range, and the table below shows where common pitches fall between the two.

PitchFall per FootGradeAngleSlope Ratio
1/4 in per 10 ft (Englert minimum)0.025 in0.208%0.119°1 in 480
1/2 in per 10 ft0.050 in0.417%0.239°1 in 240
1 in per 16 ft, or 1/16 in per ft (FHB ideal)0.0625 in0.521%0.298°1 in 192
1/8 in per ft0.125 in1.042%0.597°1 in 96

The slope ratio column answers the ideal slope ratio question. At the minimum, a gutter drops 1 unit for every 480 units of run, and at the ideal it drops 1 for every 192. A smaller second number means a steeper gutter.

Gutter Drop by Run Length

This table gives the drop for common runs at three pitches, rounded to the nearest 1/16 in. The last column counts hangers at 24 in spacing. Use the run to the downspout, not the full gutter. A 40 ft gutter split at the center uses the 20 ft row for each side.

Run to DownspoutDrop at 1/4 in per 10 ftDrop at 1/2 in per 10 ftDrop at 1 in per 16 ftHangers at 24 in
10 ft1/4 in1/2 in5/8 in6
16 ft3/8 in13/16 in1 in9
20 ft1/2 in1 in1 1/4 in11
25 ft5/8 in1 1/4 in1 9/16 in14
30 ft3/4 in1 1/2 in1 7/8 in16
40 ft1 in2 in2 1/2 in21
50 ft1 1/4 in2 1/2 in3 1/8 in26
100 ft2 1/2 in5 in6 1/4 in51

A 100 ft run to one downspout needs 2 1/2 in of drop at the minimum and 6 1/4 in at the ideal. That much tilt shows clearly against a level fascia. This is why long walls are usually split into shorter runs, each with its own downspout. Splitting the run cuts the drop each section needs.

In metric, the minimum is about 2.08 mm per meter and the ideal about 5.21 mm per meter. A 6 m gutter needs roughly 12.5 mm of fall at the minimum and 31 mm at the ideal. Switch the length unit to meters in the gutter slope calculator. Every card and table then shows meters and millimeters.

Downspout Layout and Long Runs

The downspout layout sets how long the sloped run really is. With one end downspout, the whole gutter slopes one way toward it. With downspouts at both ends, the high point sits in the middle and each half slopes outward. A center downspout does the reverse, with both ends high and water meeting in the middle.

A center split halves the run, so it halves the drop. A 40 ft gutter at 1/4 in per 10 ft needs 1.00 in to one end, but only 0.50 in per side when split. The fourth result card shows this saving. For split layouts, it reports the percent of drop saved compared with running everything to one end.

The custom spot option covers a downspout that can't sit at the center, such as one beside a door. The tool sets the drop from the longer side and gives the steeper pitch the short side needs. How many downspouts a roof needs is a sizing question, not a slope one. Englert ties gutter size to roof square footage and local rainfall.

The Roof Drainage Calculator takes the roof footprint, pitch and rainfall and gives peak runoff and downspout drain area. Once the downspout spots are set, this tool gives the fall to each one, run by run.

Hanger Marks and the Chalk Line

Englert says hangers should be no more than 18 to 24 in apart. Wider spacing lets the gutter sag and hold water between supports. The calculator defaults to 24 in and counts one hanger at each end. A 40 ft gutter at that spacing takes 21 hangers.

The Hanger Mark-Out Table lists each hanger's distance from the left end and its drop below the high point. It also gives the nearest 1/16 in tape mark. At 1/4 in per 10 ft and 24 in spacing, each hanger sits only 0.05 in lower than the one before. That is too small to measure one hanger at a time.

So snap a chalk line instead. Mark the high end tight under the drip edge, mark the full drop at the downspout end, and set every hanger on the line between them. Fine Homebuilding adds one more detail. The front lip of the gutter should sit about 1 in lower than the back, so overflow spills out the front and not onto the fascia.

Checking an Existing Gutter

Use Check an Existing Gutter mode when water stands in a gutter that is already up. Pull a level string line or laser from the high end and measure down at the downspout end. Enter that drop with the run length and your target pitch. The tool shows the real pitch and how far the low end needs to move.

Take a 32 ft gutter that measures only 1/2 in of drop. The hero shows 0.156 in per 10 ft, and the pitch card reads it as 62% of the minimum. At 1/4 in per 10 ft, that run needs 0.80 in. The second card says to lower the low end by 0.30 in, and the hanger card lists 17 hangers to re-set.

The high end stays fixed under the drip edge, and only the downspout end moves. The hanger at mid-run moves half as far, 0.15 in in this example. That is the simple way to adjust or increase gutter slope. You re-set the hangers in proportion instead of taking the whole run down.

Gutters do not need to be perfectly level, and Check mode flags a level run in red. Englert notes standing water makes gutters sag and can freeze into ice dams, so a level gutter gets the exact drop it needs at the downspout end.

Percent Grade and Degrees

Many slope searches are really unit conversions. Grade is the drop divided by the run, times 100, and the angle is the arctangent of drop over run. To work out any slope by hand, keep the drop and run in the same units.

G is the grade in percent. A 1% slope is 0.573 degrees, a 2% slope is 1.146 degrees and a 5% slope is 2.862 degrees. Even a 1% grade is almost five times the gutter minimum. The pitch box takes degrees, percent, inches per foot, inches per 10 ft and mm per meter.

GradeDegreesInches per FootInches per 10 ftmm per Meter
0.208%0.119°0.0250.252.08
0.5%0.286°0.060.65
1%0.573°0.121.210
2%1.146°0.242.420
5%2.862°0.6650
70%34.992°8.484700

A 2% slope is 0.24 in of fall per foot, so over 4 ft it drops 0.96 in. In meters, the same 2% grade is 20 mm per meter. A 0.5% slope is 0.6 in per 10 ft. That sits between the Englert minimum and the Fine Homebuilding ideal, so it suits a gutter well.

A 70% slope is about 35 degrees, which is roof or hillside territory. The pitch box stops at 25% because no gutter runs that steep. For ditches and swales, the Channel Slope Calculator finds slope from an elevation drop and length. It handles open channels that a gutter tool does not.

Gutter Size Comes First

Slope keeps water moving toward the outlet, but it cannot make up for a gutter that is too small. Englert lists the wrong gutter size as a common installation error. Englert says size should come from roof square footage and local rainfall. That is what a gutter slope calculator square feet search usually means, since size is set before slope.

For whole sites rather than one roof, the Storm Water Runoff Calculator estimates peak runoff. It uses the rational method with area, rainfall and a runoff coefficient. For residential K-style systems, Englert stocks parts in 5 in and 6 in sizes. Its downspouts come in 2x3 and 3x4 in.

Whether a house needs 4, 5 or 6 in gutters depends on roof area and rainfall, not a fixed rule. Once size and downspout spots are settled, run the gutter slope calculator for each section between a high point and its downspout.

When Water Still Sits in the Gutter

A gutter with the right pitch on paper can still hold water. Englert names wide hanger spacing, sagging from debris or ice, and a run never pitched toward the downspout. Each of these leaves low spots that one end-to-end measurement will miss. After re-setting the slope, run a hose at the high end and watch for pooling.

Englert also says downspouts should discharge at least 5 to 10 ft from the house. A buried drain line that carries water farther away works too. That buried line needs its own fall. The Drainage Fall Calculator and Pipe Slope Calculator handle the underground run.

The French Drain Calculator sizes a gravel trench to spread the water on site. For a rain barrel or cistern, the Tank Volume Calculator gives capacity in gallons for common tank shapes.

Gutter Slope Calculator FAQs

These answers use the same math as the gutter slope calculator above, worked out for the runs and slopes people ask about most. Each recommended pitch is tied to the source it comes from.

What is the correct slope for a gutter?

Aim for at least 1/4 in of fall per 10 ft, the Englert minimum. Treat 1 in per 16 ft as the upper end, which Fine Homebuilding calls ideal. In inches per foot that range is 0.025 to 0.0625 in.

As a grade it is about 0.21% to 0.52%, or 0.12 to 0.30 degrees. On a long run, lean toward the flatter end or add a second downspout. Either way, the gutter must fall steadily with no low spots between hangers.

How much fall does 100 ft of gutter need?

Run to one downspout, 100 ft needs 2 1/2 in of fall at 1/4 in per 10 ft. At 1 in per 16 ft it needs 6 1/4 in, which shows clearly against the fascia. With downspouts at both ends, each 50 ft half needs 1 1/4 in at the minimum. A 20 ft gutter needs just 1/2 in at the minimum and 1 1/4 in at the ideal.

How much gutter fall over 6 m?

A 6 m gutter needs about 12.5 mm of fall at the minimum, or 2.08 mm per meter. At the 1 in per 16 ft ideal, it needs about 31 mm. Enter 6 with the length unit set to meters. The calculator gives the drop in millimeters and lists each hanger position in meters.

Do gutters need to be perfectly level?

No. A level gutter has no fall to move water, so it sits in the trough after every rain. Englert links that standing water to sagging and ice dams. Some installers run short near-level stretches to stay under the drip edge. The gutter as a whole must still fall toward the outlet.

How do I test gutter slope?

Stretch a level string line or laser from the high end and measure down at the downspout end. Enter that drop and the run in Check mode to get the real pitch. Then run a hose at the high end. Water that stops partway shows a low spot between hangers that an end measurement can't reveal.

Is it normal for gutters to drip in heavy rain?

Some spill over the front in a downpour is expected. Fine Homebuilding sets the front lip about 1 in lower than the back so overflow goes out the front. Overflow in normal rain is a warning sign. It usually means a clog, an undersized gutter, or a pitch too flat or too steep for water to reach the downspout.

Can I enter the gutter pitch in degrees or percent?

Yes. The pitch box takes inches per 10 ft, inches per foot, percent grade, degrees or mm per meter, and every card converts back to the other units. A 0.3 degree entry works out to a 0.524% grade and 0.63 in per 10 ft. The pitch card flags it as just past the 1 in per 16 ft ideal.