Clapboard siding calculator for fiber cement, engineered wood and cedar lap boards, with wall and gable courses, an even story-pole reveal, the boards to order, trim, nails, costs.
Add up the width of every wall to be sided. Height runs from the bottom course to the soffit or frieze board.
Gables, Openings & Corners
Board Size, Waste & Price
Lap Profile & Coursing Diagram
Trim, Starter & Nail Takeoff
| Item | Amount | Order |
|---|---|---|
| Starter strip, wall bottoms | 140 lin ft | 12 pieces of 12 ft |
| Outside corner boards, 2 faces | 72 lin ft | 8 pieces of 12 ft |
| Door casing, sides and head | 33 lin ft | 3 pieces of 12 ft |
| Window casing, 4 sides | 150 lin ft | 13 pieces of 12 ft |
| Siding nails, 1 per stud per course | 1,767 nails | studs at 16 in OC |
Clapboard Size Chart for This House
| Siding Product | Exposure | Wall Courses | Boards per Square | Boards (12 ft) |
|---|---|---|---|---|
| Fiber Cement 5.25 in | 4 in | 27 | 25.0 | 380 |
| Fiber Cement 6.25 in | 5 in | 22 | 20.0 | 310 |
| Fiber Cement 7.25 in | 6 in | 18 | 16.7 | 254 |
| Fiber Cement 8.25 in | 7 in | 16 | 14.3 | 226 |
| Fiber Cement 9.25 in | 8 in | 14 | 12.5 | 198 |
| Fiber Cement 12 in | 10 3/4 in | 11 | 9.3 | 156 |
| Engineered Wood 8 in | 6.844 in | 16 | 14.6 | 226 |
| Cedar Bevel 4 in | 2 1/2 in | 44 | 40.0 | 617 |
| Cedar Bevel 6 in | 4 1/2 in | 24 | 22.2 | 338 |
| Cedar Bevel 8 in | 6 1/4 in | 18 | 16.0 | 254 |
| Cedar Bevel 10 in | 8 1/4 in | 14 | 12.1 | 198 |
Step-by-Step Siding Math
Clapboard Siding Calculator Counts by Board Width
A 140 ft run of 9 ft walls with two 30 ft gables, two doors and ten windows needs 226 boards of 8.25 in HardiePlank at 12 ft, with 15% waste. That is 16 wall courses at a 7 in exposure and 1,310 sq ft of net wall.
Board width changes the clapboard siding calculator count more than anything else. Every row below is for that same house, with 1 1/4 in lap on fiber cement, 1 in lap on LP SmartSide and cedar, and 15% waste.
| Board | Exposure | Wall Courses | Boards per Square | 12 ft Boards |
|---|---|---|---|---|
| HardiePlank 5.25 in | 4 in | 27 | 25.0 | 380 |
| HardiePlank 6.25 in | 5 in | 22 | 20.0 | 310 |
| HardiePlank 7.25 in | 6 in | 18 | 16.7 | 254 |
| HardiePlank 8.25 in | 7 in | 16 | 14.3 | 226 |
| HardiePlank 9.25 in | 8 in | 14 | 12.5 | 198 |
| HardiePlank 12 in | 10 3/4 in | 11 | 9.3 | 156 |
| LP SmartSide 8 in | 6.844 in | 16 | 14.6 | 226 (170 at 16 ft) |
| Cedar bevel 4 in | 2 1/2 in | 44 | 40.0 | 617 |
| Cedar bevel 6 in | 4 1/2 in | 24 | 22.2 | 338 |
| Cedar bevel 8 in | 6 1/4 in | 18 | 16.0 | 254 |
| Cedar bevel 10 in | 8 1/4 in | 14 | 12.1 | 198 |
Cedar is sold by nominal width, so a 6 in cedar board is really 5 1/2 in wide and covers 4 1/2 in after a 1 in lap. That narrow cover pushes the 6 in cedar count to 338 boards, against 310 for a 6.25 in fiber cement plank.
LP SmartSide 8 in lap is 7.844 in wide and comes in 16 ft lengths, so match the clapboard siding calculator board length to the product.
Ordered at its own length, the same house takes 170 boards instead of 226 at 12 ft, with fewer butt joints to flash and caulk.
Cedar board feet follow nominal size, not cover width, so check both figures in any wood clapboard siding calculator estimate.
The 6 in profile uses 1.33 bd ft per sq ft of wall, or 2,026 bd ft for the house, while the 10 in profile uses 1.21 bd ft per sq ft and 1,977 bd ft in total.
Exposure, Overlap and the Story Pole
Exposure, the first number in any clapboard siding calculator, is the board width minus the overlap. An 8.25 in HardiePlank with the 1 1/4 in minimum lap shows 7 in, and a nominal 6 in cedar bevel board with a 1 in lap shows 4 1/2 in.
E is the exposure, Wb the actual board width and L the overlap, all in inches. James Hardie's HardiePlank instructions set a minimum 1 1/4 in overlap for both face and blind nailing.
LP's own lap siding guide calls for at least 1 in of overlap on SmartSide. For cedar, Real Cedar lists 1 in for 4 and 6 in boards, 1 to 1 1/8 in for 8 in, 1 to 1 1/2 in for 10 in and 1 to 2 in for 12 in.
A wall height rarely divides evenly by the exposure, a detail that changes every clapboard siding calculator layout. A 9 ft wall at 7 in works out to 15.43 courses, so the top course would show only 3 in, a thin sliver under the soffit trim.
The fix is a story pole laid out from the clapboard siding calculator course count. Round the courses up to 16 and divide the wall evenly, which gives a 6 3/4 in reveal on every course and raises the lap to 1 1/2 in, still above the 1 1/4 in minimum.
| Wall Height | Courses at 7 in | Top Course at 7 in | Rounded Courses | Story-Pole Reveal | Resulting Lap |
|---|---|---|---|---|---|
| 8 ft | 13.71 | 5 in | 14 | 6.857 in | 1.393 in |
| 8.5 ft | 14.57 | 4 in | 15 | 6.8 in | 1.45 in |
| 9 ft | 15.43 | 3 in | 16 | 6.75 in | 1.5 in |
| 10 ft | 17.14 | 1 in | 18 | 6.667 in | 1.583 in |
| 12 ft | 20.57 | 4 in | 21 | 6.857 in | 1.393 in |
| 18 ft | 30.86 | 6 in | 31 | 6.968 in | 1.282 in |
The table uses 8.25 in fiber cement, the most common Hardie lap siding calculator case. A 10 ft wall is the worst case, since 7 in leaves a 1 in strip at the top, while an 18 ft two-story wall needs only a 1/32 in trim per course.
Cedar works the same way. A 9 ft wall in 6 in cedar fits exactly 24 courses at 4 1/2 in, but a 10 ft wall needs 27 courses at about 4.444 in, which lifts the lap to about 1 1/16 in.
Courses vs Square Feet on a Real Wall
Counting full courses orders more siding than dividing the wall area by board coverage, the shortcut behind many basic estimates.
In this clapboard siding calculator example, courses give 2,356 lin ft before waste, while area divided by exposure gives 2,246 lin ft, about 5% less.
N is the number of wall courses, H the wall height in feet and E the exposure in inches, rounded up because a partial top course still takes a full board ripped to width. The wall siding is then N times the wall width.
The clapboard siding calculation for the 140 ft of 9 ft walls is 16 × 140 = 2,240 lin ft. An area method would give 140 × 9 × 12 ÷ 7 = 2,160 lin ft, missing the ripped top course on every wall.
Openings come out of the clapboard siding calculator total at the exposure rate. The two 36 × 80 in doors and ten 36 × 54 in windows cover 175 sq ft, which equals 300 lin ft of siding at a 7 in exposure.
That deduction is only fair on large openings. Siding still runs past short windows in full boards that are then cut out, so a clapboard siding calculator estimate for many small windows still needs its waste allowance.
For a single wall, the clapboard siding calculator square feet answer and the board count go together. A 20 × 8 ft wall in 7 in exposure has 14 courses, 280 lin ft and 24 boards at 12 ft, covering 160 sq ft, or 1.6 squares.
The Wall Square Footage Calculator breaks a house into walls with doors and windows removed. The Siding Calculator covers panel and shake siding where courses do not apply.
Gable Ends and the Half-Area Rule
A gable takes more siding than half its rectangle, because every course is cut from a board as long as its widest edge.
In clapboard siding calculator terms, a 30 ft gable 7.5 ft high takes 208 lin ft of 7 in siding, against 193 lin ft by the half-area rule.
G is the gable siding in linear feet, Wg the gable base width in feet, Hg the peak height in feet and n the gable course count, 12 × Hg ÷ E rounded up. Each course is charged at the length of its lower edge.
| Gable Height (30 ft Base) | Roof Pitch | Courses at 7 in | Siding by Course | Half-Area Rule | Extra |
|---|---|---|---|---|---|
| 5 ft | 4/12 | 9 | 144.0 lin ft | 128.6 lin ft | 12.0% |
| 7.5 ft | 6/12 | 13 | 208.0 lin ft | 192.9 lin ft | 7.9% |
| 10 ft | 8/12 | 18 | 272.2 lin ft | 257.1 lin ft | 5.9% |
| 15 ft | 12/12 | 26 | 400.8 lin ft | 385.7 lin ft | 3.9% |
Low-pitch gables lose the most to the half-area rule, 12% on a 4/12 roof, in this clapboard siding calculator comparison. A lap siding calculator for gable ends that halves the rectangle comes up short on exactly the gables that look simplest.
Both ends of every gable course are cut at the roof angle, and those offcuts seldom fit the next course up. Set waste at 15 to 20% in a clapboard siding calculator estimate whenever gables are part of the job.
Trim, Starter Strip and Nails
Beyond the boards, the sample house needs 140 lin ft of starter strip, 72 lin ft of outside corner board, 32.7 lin ft of door casing and 150 lin ft of window casing.
Siding nails for the same clapboard siding calculator example come to 2,033 at studs 16 in on center, one per stud on every course.
Corner boards count both faces of each outside corner over the wall height, so four corners on 9 ft walls take 8 pieces of 12 ft trim. Door casing runs both sides and the head, and window casing runs all four sides.
Nailing follows the studs. LP calls for a nail at every stud on SmartSide, and Hardie allows studs up to 24 in on center, so one nail per stud per course is the count to plan for.
| Stud Spacing | Siding Nails for the Sample House | Nails per Board |
|---|---|---|
| 16 in on center | 2,033 | 9 |
| 24 in on center | 1,355 | 6 |
The nail count runs on the linear feet including waste, so it slightly over-orders, which suits a box sold by the pound.
Cedar is nailed differently, with Real Cedar calling for one nail per piece at each stud, set just above the lap so it never pins two boards together.
Butt joints need their own space. LP calls for a 3/16 in gap at each butt joint and at trim, filled later with sealant, and the Sealant Calculator sizes the tubes from joint length.
Price per Board, Foot or Square
At $14.50 per 12 ft board, the sample house costs $3,277 for 226 boards. That equals $1.21 per linear foot and $250.15 per square of net wall, because the waste boards are paid for but cover nothing.
Suppliers quote clapboard per board, per linear foot or per square, and each converts through board coverage.
In a clapboard siding calculator comparison, a 12 ft board at a 7 in exposure covers 7 sq ft, so $14.50 per board equals $207.14 per square of coverage before waste.
| Waste Allowance | Boards | Linear Feet | Squares Ordered | Cost at $14.50 |
|---|---|---|---|---|
| 5% | 207 | 2,474 | 13.76 | $3,001.50 |
| 10% | 216 | 2,592 | 14.41 | $3,132.00 |
| 15% | 226 | 2,709 | 15.06 | $3,277.00 |
| 20% | 236 | 2,827 | 15.72 | $3,422.00 |
Each 5% step adds about 10 boards and $145 on this house. Going from 10% to 15% costs $145 more and covers the angled rake cuts on both gables.
Any clapboard siding cost calculator figure needs the price basis the yard quotes. A per-square price for cedar usually assumes a set exposure, so check it matches the lap planned on the story pole before comparing it with fiber cement.
Primed fiber cement and engineered wood still need finish coats. The Paint Calculator works from the same 1,310 sq ft net wall area.
Finding Count, Coverage and Overlap
Each answer below uses the clapboard siding calculator sample house of 140 ft of 9 ft walls, two 30 × 7.5 ft gables and 12 openings, in 8.25 in HardiePlank, unless a single wall is named.
How do I find the number of clapboards needed?
Divide the wall height in inches by the exposure, round up to whole courses, and multiply by the wall width for linear feet. Add gable courses, subtract openings, add waste, then divide by the board length and round up.
For the sample house that is 16 courses × 140 ft = 2,240 lin ft, plus 416 lin ft of gables, minus 300 lin ft of openings. The 2,356 lin ft becomes 2,709 lin ft with 15% waste, or 226 boards at 12 ft.
Siding length comes from the same clapboard siding calculator steps. A 20 ft wall 12 ft high at a 7 in exposure has 21 courses and 420 lin ft, or 35 boards at 12 ft before waste.
How do you calculate siding coverage?
Siding coverage per board, the base of every clapboard siding calculator, is the board length times the exposure. A 12 ft board at 7 in covers 12 × 7 ÷ 12 = 7 sq ft, so 14.3 boards cover one square of 100 sq ft.
Coverage uses exposure, never the full board width. Counting 8.25 in of width instead of 7 in would claim 8.25 sq ft per board and under-order by about 15%, the same amount as a full waste allowance.
How much overlap does a lap board have?
A lap board overlaps the course below by at least 1 1/4 in on HardiePlank and at least 1 in on LP SmartSide and cedar bevel siding. Wider cedar boards take more, up to 1 1/2 in on 10 in boards and 2 in on 12 in boards.
Overlap can grow above the minimum but never shrink below it. Story-pole layout on a 9 ft wall raises the HardiePlank lap from 1 1/4 to 1 1/2 in, and that extra lap is what keeps the top course from ending as a 3 in strip.