Wall Square Footage Calculator

Updated

Wall square footage calculator for single walls, whole rooms, L-shaped and vaulted rooms: gross and net wall area after doors and windows, paint gallons, drywall sheets and rolls.

Quick Setup

Measure wall to wall at floor level; L-shaped rooms use overall size.

Doors, Windows and Openings1 Door · 2 Windows
Paint, Materials and Prices350 sq ft/gal · 2 Coats
Net Wall Area
372 sq ft Net Wall Area
4 walls, 52 ft around
416 sq ft Gross Wall Area
Doors, Windows, Openings44 sq ft
Openings Share of Wall10.6%
Every wall at full size before anything is taken out, then the area of the doors, windows and other openings you entered, and their share of it.
2.13 gal of Paint
Buy in Cans2.25 gal: 2 gal + 1 qt
One Coat Takes1.06 gal
Wall area times wall coats, plus any ceiling at its own coats, over can coverage. Bob Vila puts most paint at 250 to 400 sq ft a gallon.
13 Sheets of 4 × 8 Drywall
4 × 12 Sheets Instead9 Sheets
Order Area With Waste409 sq ft
Area to cover plus your waste allowance, divided by 32 sq ft for each 4 × 8 sheet or 48 sq ft for each 4 × 12 sheet, rounded up to whole sheets.
34.56 m² Net Wall Area
Square Yards41.33 sq yd
Square Inches53,568 sq in
The same net area in metric, in square yards, and in square inches for walls measured in inches, where 144 sq in make up 1 sq ft.
Materials and Cost9 Wallpaper Rolls

Sheets, tile and baseboard include your 10% waste. Wallpaper counts whole strips cut to the tallest wall, and paint and primer use no waste.

MaterialArea UsedQuantityPriceCost
Paint, 2 Coats372 sq ft2.25 gal: 2 gal + 1 qtNot Priced--
Drywall or Paneling, 4 × 8 ft409 sq ft13 Sheets----
Drywall, 4 × 12 ft409 sq ft9 Sheets----
Primer, 1 Coat372 sq ft2 gal in Gallon Cans----
Wallpaper, Walls Only43 ft of Strips9 Rolls (26 Strips)----
Baseboard49 ft53.9 ft With Waste----
Wall Tile, Walls Only409 sq ftAdd a Tile Size----
Wall Material by Area409 sq ft--Not Priced--
Total Priced--------
Wall by Wall540 sq ft With Ceiling
SurfaceWidthHeightArea
Wall 1, Length14 ft8 ft112 sq ft
Wall 2, Width12 ft8 ft96 sq ft
Wall 3, Length14 ft8 ft112 sq ft
Wall 4, Width12 ft8 ft96 sq ft
Less 1 door3 ft6 ft 8 in-20 sq ft
Less 2 windows3 ft4 ft-24 sq ft
Net Wall Area52 ft--372 sq ft
Ceiling----168 sq ft
Walls Plus Ceiling----540 sq ft
Floor Area----168 sq ft
Room Volume----1,344 cu ft
Common Wall Sizes24 Sizes

Width × height of one plain wall, before doors and windows.

Wall Width8 ft High9 ft High10 ft High12 ft High
8 ft Wide64 sq ft72 sq ft80 sq ft96 sq ft
10 ft Wide80 sq ft90 sq ft100 sq ft120 sq ft
12 ft Wide96 sq ft108 sq ft120 sq ft144 sq ft
14 ft Wide112 sq ft126 sq ft140 sq ft168 sq ft
16 ft Wide128 sq ft144 sq ft160 sq ft192 sq ft
20 ft Wide160 sq ft180 sq ft200 sq ft240 sq ft
Walls Laid Out Flat4 Walls
14 ft12 ft14 ft12 ft8 ftEach Wall Unfolded, Drawn to Scale
Step-by-Step MathGross - Openings
  1. Perimeter = 2 × (14 ft + 12 ft) = 52 ft; wall area = 52 ft × 8 ft = 416 sq ft.
  2. Openings = 1 × 3 ft × 6.667 ft + 2 × 3 ft × 4 ft = 44 sq ft.
  3. Net wall area = 416 sq ft - 44 sq ft = 372 sq ft.
  4. Paint = (372 sq ft × 2 coats) ÷ 350 sq ft/gal = 2.126 gal, which is 9 qt; buy 2 gal + 1 qt.
  5. Wallpaper = (52 ft - 9 ft of openings) × 12 ÷ 20.5 in = 26 strips of 100 in; 3 per 33 ft roll = 9 rolls.
  6. Drywall = 372 sq ft × (1 + 10%) ÷ 32 sq ft = 12.79, rounded up to 13 sheets.
  7. Result: 372 sq ft Net Wall Area.
Buy 2 Gal + 1 Qt
Your 2.13 gal is just past 2 gallons, so a single quart covers the rest, the same split This Old House uses in its example of 2 gallons plus a quart.

Wall Square Footage Calculator Formula: Width Times Height

In any wall square footage calculator estimate, the square footage of one wall is its width times its height, both in feet. A 12 ft wide wall that is 8 ft tall covers 96 sq ft, and a 12 by 12 ft wall covers 144 sq ft.

A is the wall area in square feet, W the width measured along the floor and H the height from floor to ceiling. Measure the width at the floor and again at the ceiling and use the larger number, since older walls are rarely square.

Measurements in inches convert by dividing by 144, because 12 in × 12 in makes one square foot. A wall measured as 150 in by 96 in is 14,400 sq in, and 14,400 ÷ 144 = 100 sq ft.

Wall SizeSquare FeetSquare Meters
8 × 8 ft64 sq ft5.95 m²
10 × 8 ft80 sq ft7.43 m²
10 × 10 ft100 sq ft9.29 m²
10 × 12 ft120 sq ft11.15 m²
12 × 8 ft96 sq ft8.92 m²
12 × 12 ft144 sq ft13.38 m²
16 × 9 ft144 sq ft13.38 m²
20 × 10 ft200 sq ft18.58 m²
40 × 40 ft1,600 sq ft148.64 m²

One square meter equals 10.764 sq ft, so divide square feet by 10.764 for a wall square footage calculator square meters result. Builders in India and the US both quote wall and floor areas in square feet, while most tile and paint sold in metric countries is labeled per square meter.

A length alone has no square footage. A request to turn feet into square feet, such as an ft to sq ft calculator, always needs a second dimension, which for a wall is its height.

Room Walls From Length, Width and Ceiling Height

Add the room length and width, double it to get the perimeter, then multiply by the ceiling height. A 12 by 14 ft room with 8 ft ceilings has a 52 ft perimeter and 416 sq ft of wall before any openings come out.

L and W are the room's length and width at floor level and H is the ceiling height. The table uses the same wall square footage calculator for home math, with one 36 × 80 in door and two 36 × 48 in windows taken out of each room.

RoomPerimeterGross Walls, 8 ftNet WallsCeiling
10 × 10 ft40 ft320 sq ft276 sq ft100 sq ft
10 × 12 ft44 ft352 sq ft308 sq ft120 sq ft
12 × 12 ft48 ft384 sq ft340 sq ft144 sq ft
12 × 14 ft52 ft416 sq ft372 sq ft168 sq ft
14 × 16 ft60 ft480 sq ft436 sq ft224 sq ft
16 × 20 ft72 ft576 sq ft532 sq ft320 sq ft
20 × 20 ft80 ft640 sq ft596 sq ft400 sq ft

Ceiling height moves a wall square footage calculator total faster than most people expect. The same 12 by 12 ft room has 384 sq ft of wall at 8 ft, 432 sq ft at 9 ft, 480 sq ft at 10 ft and 576 sq ft at 12 ft, a 50% jump from the lowest to the highest.

Floor area alone does not fix a wall square footage calculator result, because the room’s shape changes its perimeter. A 200 sq ft floor laid out as a 14.1 ft square has 452.5 sq ft of 8 ft wall, but as a 10 by 20 ft room it has 480 sq ft and as an 8.2 by 24.5 ft room it has 522.6 sq ft.

When only the floor area is known, as on a listing or plan, a square room gives the lowest wall figure. Any wall square footage calculator from square footage of the floor should be treated as a minimum unless you also know the length-to-width ratio.

Should you include the ceiling? Only when the ceiling gets the same material. Paint and drywall jobs often cover it, which adds the floor area of a flat-ceiling room, while wallpaper, tile and wainscot stay on the walls.

Doors, Windows and Garage Doors to Subtract

Subtract each opening’s width times height from the gross wall area before ordering from any wall square footage calculator for painting. A standard 36 × 80 in interior door removes 20 sq ft, and a 36 × 48 in window removes 12 sq ft.

“Standard” opening sizes vary from source to source, which is why measured openings beat default ones in a wall square footage calculator.

This Old House takes off 20 sq ft per door and 10 sq ft per window, while Bob Vila uses an 18 sq ft door and a 24 sq ft window. On a room with two windows, that spread alone is 28 sq ft.

OpeningCommon SizeAreaShare of a 12 × 8 ft Wall
Interior door30 × 80 in16.7 sq ft17%
Interior or entry door36 × 80 in20 sq ft21%
Double-hung window36 × 48 in12 sq ft13%
Patio slider72 × 80 in40 sq ft42%
Single garage door9 × 7 ft63 sq ft--
Double garage door16 × 7 ft112 sq ft--

Measure openings to the outside of the casing for paint and wallpaper, since trim is painted separately. For drywall and siding, measure the rough opening instead, because that is the hole the sheets stop at.

Garage doors are the one opening that always comes off. A wall square footage calculator with garage door entries matters most on exterior walls, where a single 16 × 7 ft door removes more than a full square of siding.

On the 12 by 14 ft room above, one door and two windows take 44 sq ft, or 10.6% of the gross wall. Add a 72 in patio slider to that room and the openings reach 84 sq ft, or 20% of the wall, which is real paint and drywall money.

Windows alone are 24 sq ft of that room’s 416 sq ft, a 5.8% share that a Window To Wall Ratio Calculator checks against energy code limits. Baseboard follows the perimeter less each door width, so the same room takes 49 ft, and a Baseboard Trim Calculator turns that into pieces.

Vaulted, Cathedral and Sloped Ceiling Walls

A gable end wall is a rectangle up to the eave height plus a triangle up to the peak. On a 12 ft wide wall with 8 ft side walls and a 12 ft peak, that is 96 sq ft plus 24 sq ft, or 120 sq ft.

W is the wall width, H the height where the ceiling meets the side walls and P the height at the peak. A wall that is only the triangle, such as an exterior gable above a ceiling, uses just the second term.

14 × 12 ft RoomWall AreaCeiling AreaWalls Plus Ceiling
Flat, 8 ft416 sq ft168 sq ft584 sq ft
Cathedral, 8 ft walls, 12 ft peak464 sq ft201.9 sq ft665.9 sq ft
Shed, 8 ft low wall, 12 ft high wall520 sq ft177.1 sq ft697.1 sq ft

When the ceiling joins a wall square footage calculator total, remember that a sloped ceiling is larger than the floor below it.

In the cathedral room each ceiling plane runs 7.2 ft from wall to ridge, not 6 ft, so the ceiling is 201.9 sq ft over a 168 sq ft floor. Painting it at the floor area would leave you 20% short.

The shed room has the most wall of the three, because its 12 ft high side is a full rectangle. Its two end walls are trapezoids, each 12 ft wide and averaging 10 ft tall, or 120 sq ft apiece.

For an exterior gable, find the peak from the roof pitch. A 30 ft wide gable at 6/12 rises 7.5 ft, so the triangle is ½ × 30 × 7.5 = 112.5 sq ft.

A wall square footage calculator exterior gable figure like that feeds straight into a Vinyl Siding Calculator or Siding Calculator estimate.

A 40 by 60 ft metal building with 14 ft eaves and a 4/12 roof has 1,680 sq ft of sidewall and 1,386.7 sq ft of endwall, gables included. Its roof is 2,529.8 sq ft, because a 4/12 slope makes the roof 5.4% larger than the 2,400 sq ft footprint.

L-Shaped and Odd-Shaped Rooms

An L-shaped room has the same wall area as the rectangle that encloses it. Its perimeter is still 2 × (length + width), so a 14 by 12 ft L with a 6 by 4 ft corner missing has 416 sq ft of 8 ft wall, exactly like the full rectangle.

The floor and ceiling are what shrink. That L has 144 sq ft of floor instead of 168, because the 24 sq ft notch is gone. Mixing the two up is the most common error in an L-shaped estimate, where people subtract the notch from the walls too.

Rooms with bump-outs, bay windows or angled walls are easier to total wall by wall in a wall square footage calculator. Measure each straight run along the floor, multiply by its height and add the results, which also handles one wall at a different height, such as a knee wall under a stair.

A wall along a staircase is a parallelogram when its top and bottom both follow the stair. Its area is the horizontal run of the stair times the wall height measured plumb, so a 10 ft run with a 3 ft high painted band above the treads is 30 sq ft.

Rooms that are not made of straight lines, such as a curved wall, can be measured by running a flexible tape along the floor at the base of the wall. That length times the height gives the wall area to within a few square feet.

Paint, Drywall and Wallpaper From Net Wall Area

Divide the net wall area by the coverage per gallon and multiply by the coats. Paint covers 250 to 400 sq ft per gallon, according to Bob Vila, with the low end for bare, textured or rough walls and the high end for smooth, previously painted drywall.

The table uses 350 sq ft per gallon and two coats on the walls only, the same math as a wall square footage calculator for paint. A quart covers about 100 sq ft, so the cans column adds a single quart only when one quart closes the gap.

Room, 8 ft WallsNet WallsPaint, 2 CoatsCans to Buy4 × 8 Drywall4 × 12 Drywall
10 × 10 ft276 sq ft1.58 gal2 gal107
10 × 12 ft308 sq ft1.76 gal2 gal118
12 × 12 ft340 sq ft1.94 gal2 gal128
12 × 14 ft372 sq ft2.13 gal2 gal + 1 qt139
14 × 16 ft436 sq ft2.49 gal3 gal1510
16 × 20 ft532 sq ft3.04 gal3 gal + 1 qt1913
20 × 20 ft596 sq ft3.41 gal4 gal2114

The cans column buys a whole gallon whenever 2 or 3 quarts would be left over. Bob Vila notes that two quarts usually cost about the same as a gallon, so 2.49 gal in the 14 by 16 ft room is cheaper as 3 gallons, and the spare covers touch-ups later.

Primer goes on as one coat at a lower coverage, 200 to 300 sq ft per gallon according to This Old House. At 250 sq ft per gallon the 372 sq ft of wall in a 12 by 14 ft room takes 1.49 gallons, which makes 2 gallons the sensible buy.

For a 10 by 12 ft room, that means 2 gallons of wall paint for two coats. With the 120 sq ft ceiling at one coat, This Old House’s 400 sq ft per gallon figure adds 0.3 gallon, just over a quart, so a gallon of ceiling white is the practical buy.

Drywall counts above come from the net area plus 10% waste, the usual wall square footage calculator for drywall approach.

Leaving small openings in the count is a fair way to cover cutoffs. On the 12 by 14 ft room, counting the gross 416 sq ft gives 15 sheets of 4 × 8 instead of 13, and a Drywall Calculator adds the screws and mud.

Wallpaper is where wall square footage calculator area math falls short. A typical double roll, such as a York Wallcoverings roll 20 1/2 in wide by 33 ft long, holds about 56 sq ft, but each strip has to be cut to the wall height plus the pattern repeat.

With a 21 in repeat on an 8 ft wall, each strip is cut 105 in long, so a 396 in roll yields only three strips. The 12 by 14 ft room needs 26 strips after the door and windows, or 9 rolls, while dividing 409 sq ft by 56 suggests 8. A Wallpaper Calculator counts by strips for that reason.

Tile follows the wall square footage calculator for tile area, usually just the backsplash or wet wall. A 30 in tall backsplash along 12 ft of counter is 30 sq ft, and a Tile Calculator converts that into tiles and boxes with cuts.

Insulation and vapor barrier use the gross wall area minus large openings only. Batts are sold by the square foot of wall they fill, and a Vapor Barrier Cost Calculator turns the same area into rolls.

Exterior and Retaining Wall Square Footage

For exterior siding, measure walls around the outside of the house, then add every gable triangle. A 48 by 30 ft one-story house with 9 ft walls has a 156 ft perimeter and 1,404 sq ft of wall before the gables and openings.

An exterior wall square footage calculator result is usually headed for siding, which is sold by the square of 100 sq ft. Garage doors, entry doors and large windows come off, while small windows are often left in to cover waste on cut-heavy walls.

A retaining wall is measured on its exposed face only. A 40 ft long wall that stands 3 ft above grade has a 120 sq ft face, and the buried courses below grade add block but not face area.

Concrete masonry units with a nominal 16 by 8 in face cover 0.89 sq ft each, or 1.125 blocks per sq ft. That 120 sq ft face takes 135 blocks before the buried course and spares, so a retaining wall square footage calculator total is the starting point for the block order, not the order itself.

Common Wall Size and Square Feet Answers

The answers below use the same wall square footage calculator assumptions as the tables above, with 8 ft ceilings, 36 × 80 in doors and 36 × 48 in windows , unless a different size is named.

What is wall square footage?

Wall square footage is the flat surface area of a wall in square feet, its width times its height. Net wall square footage is that figure after doors, windows and other openings are subtracted, and it is the number paint, wallpaper and tile are bought against.

How do you calculate net square feet?

Start any net wall square footage calculator figure with the gross area of every wall, then subtract the area of each opening. A 12 by 14 ft room has 416 sq ft gross, less 20 sq ft for one door and 24 sq ft for two windows, which leaves 372 sq ft net.

What is the standard size of a wall?

Most US homes have 8 ft ceilings, with 9 ft common in newer houses and 10 ft or more in great rooms. The International Residential Code sets a 7 ft minimum ceiling height for habitable rooms under section R305.1.

Wall width has no standard and simply follows the room. Bedroom walls usually run 10 to 14 ft, so a typical bedroom wall is 80 to 112 sq ft at 8 ft tall.

How many square feet are the walls of a 12 × 12 room?

The four walls of a 12 by 12 ft room with 8 ft ceilings total 384 sq ft, or 340 sq ft after one door and two windows. At 9 ft ceilings the gross rises to 432 sq ft and at 10 ft to 480 sq ft.

How is roof square footage different from floor square footage?

Roof area is the footprint times a pitch factor, plus overhangs. The factor is the square root of 1 plus the pitch squared, which is 1.054 for a 4/12 roof, 1.118 for 6/12 and 1.202 for 8/12. A 1,600 sq ft footprint under a 6/12 roof has about 1,789 sq ft of roof before overhangs.

Does it matter how old the house is before sanding the walls?

Homes built before 1978 may have lead-based paint, and sanding it releases lead dust. The EPA Renovation, Repair and Painting rule requires lead-safe practices for paid work in those homes, so test the paint before sanding any wall you are measuring for a repaint.

Can you frame from a wall square footage calculator total?

Studs follow wall length, not area. At 16 in on center, a 12 ft wall takes 10 studs on the layout plus extras at corners, doors and windows, so frame from the linear feet and use the square footage only for sheathing, insulation and drywall.