Dipole Antenna Length Calculator

Updated

Dipole antenna length calculator for half-wave wire and rod dipoles: total and per-leg cut lengths from frequency, adjusted for wire diameter, end wraps, mount height and retuning.

Dipole Antenna Setup

Enter the operating frequency to get the half-wave dipole length, each leg and the cut length.

Show Results In
× λ/2
Wire Wrap & Height+6 in per Leg · 50 ft High
65.92 ft Half-Wave Dipole
Exact 65.9155 ft · 20.09 m · 65 ft 11.0 in Tip to Tip
32.96 ft Each Leg
Cut per Leg (+6 in Wrap)33 ft 5.5 in
Trim Rate (1 in off Each Leg)+18.0 kHz
Each leg is L/2, the same length as a ¼-wave vertical; trim both legs equally to tune.
138.5 ft Wavelength (λ)
Length Factor (k)0.9516 × λ/2
End-Effect Shortening3 ft 4.2 in (4.84%)
Wavelength is c ÷ f; end effect makes a real wire resonate a few percent under λ/2.
0.361 λ Above Ground
Main-Lobe Take-Off Angle43.8°
Height for ½λ (30° Lobe)69.27 ft
Height in wavelengths sets the main-lobe angle over flat ground: ½λ gives about 30°.
21.3 MHz 3rd Harmonic (15m)
2nd Harmonic · High Z14.2 MHz (20m)
5th Harmonic · Low Z35.5 MHz
Odd multiples (3f, 5f) present a low feed Z, resonating slightly high; even ones do not.
Dipole Layout & Current DiagramL 65.92 ft · Leg 32.96 ft
Total L = 65.92 ftCurrent Peak at the Feed1:1Leg 32.96 ftLeg 32.96 ftCoax to RadioGround · Feed 50.00 ft High (0.361 λ)
Dipole Length Chart by BandARRL Rule (468 / f) · 18 Rows
BandDesign FrequencyTotal LengthEach LegTotal (m)
160m1.9 MHz246.3 ft123.2 ft75.08 m
80m3.75 MHz124.8 ft62.40 ft38.04 m
60m5.359 MHz87.33 ft43.66 ft26.62 m
Yours · 40m7.1 MHz65.92 ft32.96 ft20.09 m
40m7.15 MHz65.45 ft32.73 ft19.95 m
30m10.125 MHz46.22 ft23.11 ft14.09 m
20m14.175 MHz33.02 ft16.51 ft10.06 m
17m18.118 MHz25.83 ft12.92 ft7.873 m
15m21.225 MHz22.05 ft11.02 ft6.721 m
12m24.94 MHz18.77 ft9.383 ft5.720 m
CB 11m27.185 MHz17.22 ft8.608 ft5.247 m
10m28.4 MHz16.48 ft8.239 ft5.023 m
6m50.125 MHz9.337 ft4.668 ft2.846 m
FM Radio98 MHz4.776 ft28.65 in1.456 m
2m146 MHz3.205 ft19.23 in97.70 cm
1.25m223.5 MHz25.13 in12.56 in63.82 cm
70cm435 MHz12.91 in6.455 in32.79 cm
33cm915 MHz6.138 in3.069 in15.59 cm
Length Formula ComparisonAt 7.1 MHz
Formulak (× λ/2)Total LengthEach Legvs ARRL
ARRL Rule (468 / f)0.951665.92 ft32.96 ftSame
Diameter: ½ in Tubing0.967867.03 ft33.52 ft+1.7%
Diameter: 10 AWG Wire0.973867.45 ft33.72 ft+2.3%
Diameter: 12 AWG Wire0.974567.50 ft33.75 ft+2.4%
Diameter: 14 AWG Wire0.975167.54 ft33.77 ft+2.5%
Free Space (491.8 / f)1.000069.27 ft34.63 ft+5.1%
Step-by-Step Math7 Steps
1. Wavelengthλ = 299.792458 / 7.1 MHz = 42.2243 m = 138.531 ft
2. Length Factork = 468 / 491.7855 = 0.95163
3. Total LengthL = 468 / 7.1 = 65.91549 ft
4. Each Leg65.91549 / 2 = 32.95775 ft
5. Cut per Leg32.95775 + 0.5 = 33.45775 ft
6. Height in λ50 / 138.5311 = 0.36093 λ; θ = asin(1 / (4 × 0.36093)) = 43.84°
7. Result65.92 ft Half-Wave Dipole
Cut Each Leg to 33 ft 5.5 in, Then Trim to the Dip
Fit a 1:1 current balun at the center feed and trim both ends equally: each 1 in off each leg raises resonance about 18.0 kHz. In free space a flat dipole feeds near 73 Ω, about 1.46:1 on 50 Ω coax; height and nearby objects shift it.

468 Divided by Frequency: The Dipole Antenna Length Calculator Formula

A half-wave dipole cut for 7.1 MHz is 65.92 ft (20.09 m) from tip to tip, which is 468 divided by the frequency in MHz. Each leg is half that, 32.96 ft, fed at the center.

Here L is the total length of both legs in feet and f is the operating frequency in MHz. The metric version is 142.65 / f for meters, and the common 143 / f shortcut runs only 5 cm long at 7.1 MHz.

A true half wavelength in free space is 491.8 / f feet, from the speed of light published by NIST. At 7.1 MHz that is 69.27 ft, so the 468 rule cuts the wire 40.2 in shorter than a full half wave.

That shortening is a factor of 0.9516, or 4.84%. It covers the end effect, where charge bunches at each tip and the wire acts longer than it measures.

Every dipole antenna length calculator result built on 468 carries this same factor, whatever the band or wire.

The 468 constant is an average of real installs, not physics. In KB6NU's write-up of N0AX's QST modeling, resonant constants ran from 466.4 to 483.4 for heights between 1/8 and 2 wavelengths.

Since most of that range sits above 468, a 468 cut usually lands at or slightly above the target frequency. Leaving about 6 in of spare wire folded back at each end insulator gives room to lengthen without splicing.

Band-by-Band Dipole Lengths From 160 m to 70 cm

The table gives a 468-rule length at a mid-band frequency for each amateur band plus CB. The last column adds 6 in per leg for the wrap around each end insulator, so it is the wire to unroll before you cut.

BandFrequency (MHz)Total lengthEach legCut per leg with 6 in wrap
160 m1.9246.32 ft (75.08 m)123.16 ft (37.54 m)123 ft 7.9 in
80 m3.75124.80 ft (38.04 m)62.40 ft (19.02 m)62 ft 10.8 in
60 m5.35987.33 ft (26.62 m)43.66 ft (13.31 m)44 ft 2.0 in
40 m7.1565.45 ft (19.95 m)32.73 ft (9.98 m)33 ft 2.7 in
30 m10.12546.22 ft (14.09 m)23.11 ft (7.04 m)23 ft 7.3 in
20 m14.17533.02 ft (10.06 m)16.51 ft (5.03 m)17 ft 0.1 in
17 m18.11825.83 ft (7.87 m)12.92 ft (3.94 m)13 ft 5.0 in
15 m21.22522.05 ft (6.72 m)11.02 ft (3.36 m)11 ft 6.3 in
12 m24.9418.77 ft (5.72 m)9.38 ft (2.86 m)9 ft 10.6 in
11 m (CB)27.18517.22 ft (5.25 m)8.61 ft (2.62 m)9 ft 1.3 in
10 m28.416.48 ft (5.02 m)8.24 ft (2.51 m)8 ft 8.9 in
6 m50.1259.34 ft (2.85 m)4.67 ft (1.42 m)5 ft 2.0 in
2 m14638.47 in (0.977 m)19.23 in (0.489 m)No wrap, solder the ends
70 cm43512.91 in (0.328 m)6.46 in (0.164 m)No wrap, solder the ends

Band plans differ by ITU region, so take the mid-band frequency from your own allocation rather than the US picks used in the table.

Region 1 stations on 40 m (7.0 to 7.2 MHz) get a 65.92 ft dipole antenna length calculator figure at 7.1 MHz, and 80 m at 3.65 MHz needs 128.22 ft (39.08 m).

The 2 m row uses 146 MHz, which sits above the 144 to 146 MHz Region 1 allocation. A European 2 m dipole cut for 145 MHz is 38.73 in (0.984 m), about a quarter inch longer than the table figure.

Low bands punish a wrong center frequency most, because the same percentage error adds up to many more feet of wire.

Across all of 80 m (3.5 to 4.0 MHz) the right length swings 16.71 ft, while the whole 20 m band spans only 0.82 ft, so 80 m builders should settle on CW or phone before making a dipole antenna length calculator cut.

Wire Thickness Moves the Cut Length

Thicker elements resonate shorter, but on HF wire the effect on a dipole antenna length calculator result is small.

The ARRL Antenna Book (24th edition) formula, as quoted by W1VT of the ARRL Lab, sets the length factor K from the ratio of half wavelength to conductor diameter.

In this formula, lambda is the free-space wavelength, d is the conductor diameter in the same units, and ln is the natural log. The resonant length is K times the free-space half wave of 491.8 / f feet.

FrequencyElementLambda / 2dARRL KResonant lengthvs 468 rule
7.1 MHz14 AWG wire12,9700.975167.54 ft+2.5%
7.1 MHz10 AWG wire8,1570.973867.45 ft+2.3%
7.1 MHz1/2 in tube1,6620.967867.03 ft+1.7%
28.4 MHz14 AWG wire3,2430.970616.81 ft+2.0%
28.4 MHz1/2 in tube4160.959816.62 ft+0.9%
146 MHz14 AWG wire6310.962638.91 in+1.2%
146 MHz1/4 in rod1620.951738.47 in0.0%
146 MHz1/2 in tube810.943238.13 in-0.9%
435 MHz1/4 in rod540.936912.71 in-1.6%
435 MHz1/2 in tube270.921612.50 in-3.2%

Going from 14 AWG to 10 AWG on 40 m changes the length by about 1 in, so wire gauge is not worth chasing on HF. The ARRL K is a free-space value, which is why thin HF wire comes out 2% to 2.5% longer than a 468 cut.

The gap between the two is the extra shortening that height above ground and wire insulation add in a real backyard.

A 468 dipole antenna length calculator figure already folds in an average of those effects, so it is the safer starting cut for a wire antenna.

On VHF and UHF the picture flips. A 1/2 in tube on 70 cm resonates 3.2% shorter than the 468 rule, because lambda / 2d drops to 27. For rod and tube elements above 50 MHz, the ARRL K gives the better dipole antenna length calculator starting point.

Here d is the bare conductor diameter in mm and n is the AWG number, so 14 AWG is 1.628 mm and 10 AWG is 2.588 mm. Use that copper diameter, not the outside of the insulation.

Mounting Height and Take-Off Angle

Height matters as much as the dipole antenna length calculator cut. A horizontal dipole works best about half a wavelength up, with its main lobe 30 degrees above the horizon.

For 40 m that is 68.8 ft (21.0 m), for 20 m it is 34.7 ft (10.6 m), and for 10 m it is 17.3 ft (5.3 m).

Theta is the elevation angle of the lowest main lobe, lambda is the wavelength, and h is the height above ground in the same units.

The relation comes from the ground reflection adding in phase with the direct wave, and it holds while h is at least a quarter wavelength.

Height (wavelengths)Take-off angle40 m height20 m height10 m height
0.2590 degrees34.4 ft (10.5 m)17.3 ft (5.3 m)8.7 ft (2.6 m)
0.356.4 degrees41.3 ft20.8 ft10.4 ft
0.530.0 degrees68.8 ft (21.0 m)34.7 ft (10.6 m)17.3 ft (5.3 m)
0.7519.5 degrees103.2 ft52.0 ft26.0 ft
1.014.5 degrees137.6 ft (41.9 m)69.4 ft (21.1 m)34.6 ft (10.6 m)
1.59.6 degrees206.4 ft104.1 ft51.9 ft

A 40 m dipole at a typical 50 ft sits at 0.361 wavelength, which gives a 43.8 degree take-off angle. That lobe is 13.8 degrees higher than at half a wavelength, trading some long-haul reach for stronger signals at medium range.

Below a quarter wavelength the lobe points straight up, a pattern called NVIS (near vertical incidence skywave). On 80 m and 40 m that is a deliberate choice for regional coverage, so a low dipole there is not a failed install.

Height also changes the resonant frequency and the feed impedance, which is why the N0AX constants spread from 466.4 to 483.4. Cut to the dipole antenna length calculator figure, raise the antenna to its final height, and only then trim.

Quarter-Wave Legs, Monopoles and the 73 Ω Feed

One leg is half of any dipole antenna length calculator total: a quarter wave times the same 0.9516 factor, or 234 / f feet. On 2 m at 146 MHz that is 19.23 in (0.489 m), which is also the length of a quarter-wave ground plane whip.

A quarter-wave monopole over a good ground plane or radials is half a dipole, with the ground standing in for the missing leg. Its feed resistance is about half the dipole value, close to 36 Ω, so it runs a 1.39:1 SWR on 50 Ω coax.

A thin half-wave dipole in free space has a feed resistance of about 73 Ω. On 50 Ω coax that is a 1.46:1 SWR, a reflection coefficient of 0.187 and a mismatch loss of 0.15 dB.

That 0.15 dB rarely matters, but it belongs in a link budget calculator tally on VHF paths. The dipole's 2.15 dBi gain is the reference figure for an EIRP calculator.

Resonance at the dipole antenna length calculator frequency does not promise a perfect match, because the feed impedance depends on height and layout as well as length.

Over real ground the 73 Ω drifts with height, and an inverted-V with drooping legs usually drops toward 50 Ω, so a 1.3:1 to 1.5:1 SWR at resonance is normal. A 1:1 current balun at the feed keeps RF off the coax shield.

Common Dipole Builds and Multiband Use

The questions below come up most when cutting and tuning a wire dipole for 40 m, 20 m and 10 m. Each answer applies the same dipole antenna length calculator math and wrap allowance as the band table.

How long is a 20 meter dipole antenna?

A 20 meter dipole is 33.02 ft (10.06 m) long at 14.175 MHz, with two legs of 16.51 ft. Cut each leg to 17 ft 0.1 in to leave 6 in for the wrap at each end insulator.

Band edges move the dipole antenna length calculator figure by less than a foot: 33.43 ft at 14.0 MHz and 32.61 ft at 14.35 MHz. CW operators near the bottom can add about 2.5 in per leg, and phone operators near the top can trim the same amount.

How to make a 40 meter dipole antenna?

Cut two legs of 33 ft 2.7 in from 14 AWG copper or copper-clad steel, fold 6 in back through each end insulator, and join the inner ends at a center insulator or a 1:1 current balun. That gives a 65.45 ft dipole for 7.15 MHz.

Raise it to working height and find the SWR dip, since a dipole antenna length calculator cut is a starting point, not a final length.

On 40 m, shortening each leg by 1 in moves resonance up about 18 kHz, against 5 kHz on 80 m, 72 kHz on 20 m and 290 kHz on 10 m, so trim in small steps.

L old is the present total length, f dip is where the SWR now bottoms out, and f target is the frequency you want. A 67 ft dipole dipping at 6.95 MHz needs 65 ft 1.5 in for 7.15 MHz, so cut 11.24 in from each leg.

The same steps apply on other bands with the dipole antenna length calculator lengths from the table. A 20 m build uses two 17 ft 0.1 in legs and a 10 m build uses two 8 ft 8.9 in legs, each including the 6 in wrap.

Will a 40 meter dipole work on 20 meters?

Not on coax alone, even with a perfect dipole antenna length calculator cut, because the second harmonic puts the feed point in the wrong place.

At 14.2 MHz, twice its 7.1 MHz resonance, a 40 m dipole is a full wavelength long, the center feed point lands on a current minimum, and the impedance climbs into the thousands of ohms.

A 20 m dipole on 10 m has the same even-harmonic problem. Odd harmonics behave, so a 40 m dipole resonant at 7.1 MHz also shows a low-impedance dip near 21.3 MHz on 15 m, its third harmonic.

To cover 20 m with one 40 m wire, feed it with ladder line and a tuner, or add a second pair of 20 m legs to the same feed point as a fan dipole. Any dipole antenna length calculator figure still sets each element's starting cut.

Above 1 GHz, a dipole antenna length calculator result shrinks to a few inches, and board antennas take over. For those bands a microstrip patch antenna calculator fits the job better than wire math.