Electricity Cost Calculator

Updated

Electricity cost calculator for appliance running cost per hour, day, month and year from watts and hours, or a monthly bill from units used, with slab rates, fixed charge and tax.

Electricity Cost Setup

Use the watts on the appliance label; 1 unit on a bill is 1 kWh.

BTU/h per W
% capacity
units
kWh
Standby Power0 W when off
W
Slab Rates100 / 300 kWh bands
kWh
kWh
$/kWh
$/kWh
Fixed Charge & Tax$10/month · 5% tax
%
Electricity Cost for Heater (portable), 1,500 W, 4 h/day
$32.85 per Month
Typical 750-2,000 W models: $16.43-$43.80 a month
$0.270 per Hour of Use
Energy per Hour1.50 kWh
Hours Running per $13.7 h
Cost of one hour of running at the power you entered, the energy that hour uses, and how many hours one unit of money buys.
6.00 kWh (Units) per Day
Cost per Day$1.08
Units per Month183 kWh
Units the appliance uses each day including standby, what a day of use costs, and the units it adds to a monthly bill.
$394.20 per Year
Units per Year2,190 kWh
Cost per Week$7.56
Full year of use at this pattern, the units a year adds up to, and the average cost of a single week of running.
Save $8.21/Month Running 1 h Less
Yearly Saving$98.55
Running 24 h a Day$197.10/month
Money saved by running one hour less a day, or half as long for short uses, and what running it around the clock would cost.
Monthly Cost Breakdown$32.85 a month
Monthly total $32.85Running: $32.85 (100.0%)
Hourly to Yearly Cost Tablehour to year
PeriodEnergyCost
1 hour of use1.50 kWh$0.270
Day6.00 kWh$1.08
Week42.00 kWh$7.56
Month183 kWh$32.85
Year2,190 kWh$394.20
Cost by Wattage Chart4 h/day
PowerPer HourPer DayPer Month
40 W$0.0072$0.029$0.876
60 W$0.011$0.043$1.31
100 W$0.018$0.072$2.19
200 W$0.036$0.144$4.38
300 W$0.054$0.216$6.57
500 W$0.090$0.360$10.95
1,000 W$0.180$0.720$21.90
1,500 W$0.270$1.08$32.85
2,000 W$0.360$1.44$43.80
3,000 W$0.540$2.16$65.70
Step-by-Step Electricity Cost Math6 steps
Power1,500 W
Hours per day4 h running
Units per day(1,500.0 W × 4.000 h) ÷ 1,000 = 6.0000 kWh
Cost per day6.0000 kWh × $0.1800/kWh = $1.08
Cost per month$1.08 × 30.42 days (365 ÷ 12) = $32.85
Result$32.85 per Month
$32.85 a Month to Run
Label watts are the most the appliance can draw; fridges, A/C units and heaters cycle on and off, so set Use/Run At Capacity to their real share, such as 40% for an A/C on a saving mode.

Electricity Cost Calculator Math: Watts to kWh to Money

Electricity cost is watts times hours, divided by 1,000, times the price per kWh. A 1,500 W heater run 4 hours a day uses 6 kWh, which costs $1.08 a day and $32.85 a month at $0.18 per kWh.

C is the cost, P is the power in watts, t is the hours of use and r is the price per kWh. Dividing by 1,000 turns watt-hours into kilowatt-hours, the unit every bill charges for.

A month here is 365 ÷ 12 = 30.42 days, so the monthly figure is the daily cost times 30.42 and a year is the daily cost times 365. Using a flat 30 days trims about 1.4% off every monthly result.

On a yearly electricity cost calculator basis, the same heater costs $394.20 a year and $7.56 a week. Cutting one hour a day saves $8.21 a month, or $98.55 a year, because each hour of a 1,500 W load is 1.5 kWh.

The price behind each electricity cost calculator result is the rate on the bill, not the total divided by units, since bills also carry fixed charges and tax.

EIA's Short-Term Energy Outlook puts the 2026 US residential average at 18.2 cents per kWh, up from 17.3 cents in 2025.

Any electricity cost calculator per kWh answer scales in a straight line with the rate. At $0.36 per kWh every dollar cost in the tables here doubles, and at $0.09 every one halves.

Running Costs for 30 W to 2,000 W

A 100 W device costs 1.8 cents an hour at $0.18 per kWh and ₹0.80 an hour at ₹8 per unit. Run nonstop for a month, the same 100 W uses 73 kWh and costs $13.14.

PowerkWh per hourPer hour at $0.18Per hour at ₹8Month at 8 h/dayMonth at 24 h/day
30 W0.03$0.0054₹0.24$1.31$3.94
40 W0.04$0.0072₹0.32$1.75$5.26
100 W0.1$0.018₹0.80$4.38$13.14
200 W0.2$0.036₹1.60$8.76$26.28
300 W0.3$0.054₹2.40$13.14$39.42
500 W0.5$0.090₹4.00$21.90$65.70
1,000 W1.0$0.180₹8.00$43.80$131.40
1,500 W1.5$0.270₹12.00$65.70$197.10
2,000 W2.0$0.360₹16.00$87.60$262.80

"Watts per hour" is not a real unit, but the question behind it is the cost of one hour. A 40 W bulb uses 0.04 kWh in an hour, so it takes 25 hours to use one unit and costs under a cent an hour at US rates.

A 300 W load costs $39.42 a month only if it runs around the clock. At 8 hours a day the same 300 W costs $13.14, so the hours matter as much as the watts in any electricity cost calculator monthly figure.

A 1,000 W appliance running one hour uses exactly 1 kWh, so its hourly cost equals the price per unit. That makes 1,000 W the quickest check on any appliance electricity cost calculator result.

A 150 W desktop PC on for 8 hours a day costs $6.57 a month, against $2.19 for a 50 W laptop on the same schedule. A gaming PC under load draws more, so its own measured watts belong in a pc electricity cost calculator run.

Labels sometimes list amps and volts instead of the watts an electricity cost calculator starts from. The Electrical Power Calculator converts amps and volts to watts, and the Current Calculator works the other way.

Units on the Bill, 40 to 1,000 kWh

One unit on a bill is one kWh. At a single rate of $0.18 plus a $10 fixed charge and 5% tax on the whole bill, 200 units cost $48.30 and 500 units cost $105.00.

Units (kWh)Energy only at $0.18Single rate + $10 + 5%Slab rates + $10 + 5%Example ₹ slabs + ₹100 + 5% duty₹ average per unit
40$7.20$18.06$18.06₹268₹6.70
100$18.00$29.40$29.40₹520₹5.20
200$36.00$48.30$50.40₹1,150₹5.75
250$45.00$57.75$60.90₹1,465₹5.86
300$54.00$67.20$71.40₹1,780₹5.93
500$90.00$105.00$123.90₹3,460₹6.92
1,000$180.00$199.50$255.15₹7,660₹7.66

The dollar slabs charge the first 100 units at $0.18, units 101 to 300 at $0.20 and the rest at $0.25.

The rupee column uses ₹4, ₹6 and ₹8 for the same bands as an example tariff, not any state's actual rates, with the 5% duty on the energy charge only.

Small bills cost the most per unit. At 40 units the fixed charge pushes the average to ₹6.70 against ₹5.20 at 100 units, so the energy rate alone understates a low-use bill.

A 500-unit month is the same as a 685 W load running nonstop, since 500 kWh spread over 730 hours is 0.685 kW. That steady-load view, set beside an electricity cost calculator run for each appliance, points to the one behind a high bill.

An electricity cost calculator india estimate needs the state board's slab table, which changes with each tariff order. The Energy Consumption Calculator adds up units for a whole house before pricing them.

AC Tonnage Is Cooling, Not Power Drawn

A 1.5 ton AC draws about 1.5 to 1.8 kWh in an hour of full running, not the 5.3 kWh a straight ton-to-watt conversion gives. At ₹8 per unit that is ₹12 to ₹14.40 an hour.

P is the electrical input in watts, Q is the cooling capacity in BTU per hour and EER is the energy efficiency ratio. One ton is 12,000 BTU/h, so 1.5 tons is 18,000 BTU/h.

The US Department of Energy defines EER as cooling capacity in BTU per hour divided by power input in watts, as its room air conditioner guide explains. Higher EER means fewer watts for the same cooling.

1.5 ton AC, EERInput powerPer hour at ₹810 hours at ₹812 hours at ₹8Month, 8 h/day at 60%
92,000 W₹16.00₹160.00₹192.00₹2,336
101,800 W₹14.40₹144.00₹172.80₹2,102
111,636 W₹13.09₹130.90₹157.10₹1,911
121,500 W₹12.00₹120.00₹144.00₹1,752

The 10- and 12-hour columns assume the compressor never stops, which is the worst case. The monthly column assumes the compressor works 60% of the time once the room is cool; a mild set point can bring that share lower.

Treating 1.5 tons as 5,275 W, the thermal equivalent of 18,000 BTU/h, triples the estimate. Use the input watts on the AC's label or its BTU/h divided by EER in any electricity cost calculator kWh estimate.

For an electricity cost calculator per hour figure, a 1 ton unit at EER 10 draws 1,200 W and a 2 ton unit 2,400 W. At $0.18 per kWh, the EER 10 unit at 1.5 tons costs $0.324 an hour of full running.

Fridges and Other Cycling Loads

A fridge rated 725 W runs at that power only about a third of the time. At 33% it uses 5.74 kWh a day and $31.44 a month at $0.18, against $95.27 if the label watts ran all 24 hours.

The one-third rule is a US Department of Energy figure, repeated in Virginia Tech Extension's appliance energy guide. Divide the plugged-in hours by three to get the hours at full wattage, the share any electricity cost calculator needs for a fridge.

The 725 W figure describes an older full-size fridge, and 2,096 kWh a year is high for a new one. The yellow EnergyGuide label lists a model's own kWh per year, which beats any rule of thumb for an appliance electricity cost calculator check.

Heaters with thermostats, water heaters and AC units also cycle. If a 1,500 W portable heater holding a warm room runs half the time, its 8 hours a day cost $32.85 a month instead of the $65.70 a full run gives.

Washers, dishwashers and dryers swing between heating and motor-only phases. Their rated watts mark the heating peak, so a full-run electricity cost calculator estimate for them reads high unless the run share is cut to match.

Standby Draw Over a Year

A device that draws 10 W while switched off uses 87.6 kWh a year, which costs $15.77 at $0.18 or ₹701 at ₹8, all of it for an appliance doing nothing.

Standby drawkWh per yearCost at $0.18Cost at ₹8
1 W8.8$1.58₹70
5 W43.8$7.88₹350
10 W87.6$15.77₹701
20 W175.2$31.54₹1,402
50 W438.0$78.84₹3,504

Standby counts only for the hours the device is off in an electricity cost calculator total. A 120 W TV watched 5 hours a day with 10 W standby uses 0.79 kWh a day, and $1.04 of its $4.33 monthly cost is the 19 idle hours.

That 24% share is why an electricity cost calculator with standby included reads higher than one without. A switched power strip cuts the idle draw to zero for devices that do not need to stay on.

A 9 W LED on 5 hours a day costs $2.96 a year against $19.71 for a 60 W incandescent bulb. The Electrical Energy Calculator converts the same watts and hours to joules or BTU when kWh is not the unit needed.

Slab Rates, Standing Charges and Tax

With slab rates, only the units inside each band pay that band's price. At 250 units, the next 100 cost $23.63 on the dollar slabs above, while the same 100 added at 300 units cost $26.25.

A bill just over a slab boundary gains the most from a small cut, since its last units carry the higher price. At 320 units, cutting 20 removes $5.25 including tax, all at the $0.25 band.

UK and many European bills add a standing charge per day instead of per month. A 50p daily charge comes to £15.21 a month on a 365 ÷ 12 basis, which belongs in any electricity cost calculator uk bill total.

India adds electricity duty as a percentage of the energy charge, and many bills add a fuel adjustment charge per unit. So 1 kWh electricity cost in India runs above the slab rate alone.

Add the fuel charge to the unit rate, since it moves with each unit used, and apply the duty to the energy charge before any fixed charge.

In the example rupee bill, 5% duty on the energy charge plus a ₹100 fixed charge raises 200 units from ₹1,000 of energy to ₹1,150.

Charged on the whole bill instead, the way UK VAT works, the same 5% gives ₹1,155. An electricity bill unit rate calculator check on a real bill works the same way from the printed charges.

For electricity cost calculator near me searches, the local rate sits on the utility's tariff sheet or the latest bill.

EIA's July 2026 state averages ran from about 12.7 cents in Louisiana to 48 cents in Hawaii, so the national figure can miss a local bill by half.

Fans, Units and Running the AC All Day

These answers use the rates in the tables above, $0.18 or ₹8 per unit, with no fixed charge or tax unless they say otherwise.

Is 1 unit 1kW?

One unit is 1 kWh, not 1 kW. A kW is a rate of power, and a kWh is that power used for an hour, so a 1 kW heater uses 1 unit each hour and a 100 W bulb takes 10 hours to use one.

The cost of 1 unit is the price per kWh on the bill, such as ₹8 or $0.18. With fixed charges and tax spread in, the true average per unit runs higher, as the ₹6.70 average on a 40-unit bill shows.

Can we run AC for 12 hours?

An AC is built to run for long stretches, and 12 hours a day is normal in hot climates. A 1.5 ton unit at EER 10 costs up to ₹172.80 for 12 hours of full running, and less once the compressor starts cycling.

The first stretch, while the room cools down, runs at full power; after that the compressor cycles. A higher night set point shortens each run and lowers the cost of every hour.

Does keeping AC on 24 save electricity?

Running an AC around the clock uses more units than switching it off when nobody is home. A 1,800 W unit at 60% uses 1.08 kWh an hour, so 12 idle hours a day add about 13 units a day.

Switching off for a long absence saves those hours outright. The restart only adds one cool-down run at full power, which costs far less than the idle hours it replaces.

Is 2 fan equal to 1 AC?

Two 75 W fans draw 150 W, a twelfth of a 1,800 W AC. One hour of both fans costs ₹1.20 at ₹8 per unit, against ₹14.40 for the AC running flat out.

A fan only moves air and does not lower the room temperature, so it cannot replace an AC in heavy heat. Using fans with the AC set about 2 °C warmer keeps the room comfortable while the compressor runs less.

How can I reduce my electricity bill?

Cut hours on the largest loads first. One hour less a day on a 1,500 W heater saves $8.21 a month, more than the $5.58 a month saved by swapping four 60 W bulbs for 9 W LEDs on 5 hours a day.

Next, stop standby draw, raise the AC set point and keep monthly use under the next slab boundary. A 20 W standby total alone costs $31.54 a year, and 50 units moved below a slab line save that band's higher price.

What is a monthly electric bill estimate?

It is the units for the month times the rate, plus fixed charges and tax. At $0.18 per unit, $10 fixed and 5% tax, 500 units come to $105.00, and the same bill on the slab rates above comes to $123.90.

An electricity cost calculator monthly estimate can add units appliance by appliance, or take them from the meter by subtracting last month's reading from this month's.

The difference is the units used, and multiplying by the rates, then adding fixed charges and tax, gives the bill before any late fees.