Feet and Inches Calculator

Updated

Feet and inches calculator math for tape lengths with fractions as fine as 1/64 in, covering sums, differences, area, equal parts, stud counts, decimal feet and metric conversions.

Feet & Inches Math

Type whole numbers, decimals or fractions like 6 3/8 or 6-3/8. Leave feet or inches empty if you only have one.

ft
in
ft
in
mm
mm
Spacing, Studs & Stock16 in OC, 8 ft stock
in
in
Sum of Lengths (A + B)
15 ft 9 7/8 in
Exact 189.8750 in, rounded to the nearest 1/16 in
15.8229 Decimal Feet
Total Inches189 7/8 in
Yards5.2743 yd
Decimal feet divide the total inches by 12. Use them in plans, laser levels and any math that needs a single number.
482.28 cm Metric Length
Millimeters4,822.8 mm
Meters4.8228 m
Metric values use the exact international inch of 25.4 mm, so these conversions carry no rounding beyond the digits shown.
7 ft 10 15/16 in Halfway Mark
One Third5 ft 3 5/16 in
One Quarter3 ft 11 1/2 in
Half, third and quarter marks are the usual layout points for centering, spacing shelves and splitting a run evenly.
13 Studs at 16 in on Center
8 ft Stock Pieces2, 2 1/8 in offcut
Last Bay1 ft 1 7/8 in
Studs land at each spacing mark plus one at the start. Stock pieces show how many full-length boards cover the run end to end.
Tape Diagram15 ft 9 7/8 in
A 11 ft 2 1/4 inB 4 ft 7 5/8 inA + B = 15 ft 9 7/8 in
Layout Marks From Start
Inches to Decimal Feet Chart9 7/8 in highlighted
InchesDecimal FeetFraction of a FootMillimeters
0 in0 ft00.0 mm
1 in0.0833 ft1/1225.4 mm
2 in0.1667 ft1/650.8 mm
3 in0.25 ft1/476.2 mm
4 in0.3333 ft1/3101.6 mm
5 in0.4167 ft5/12127.0 mm
6 in0.5 ft1/2152.4 mm
7 in0.5833 ft7/12177.8 mm
8 in0.6667 ft2/3203.2 mm
9 in0.75 ft3/4228.6 mm
10 in0.8333 ft5/6254.0 mm
11 in0.9167 ft11/12279.4 mm
12 in1 ft1304.8 mm
9 7/8 in (yours)0.8229 ft0.8229250.8 mm
Step-by-Step Feet and Inches Math4 steps
A in inches11 ft × 12 + 2.25 in = 134.25 in
B in inches4 ft × 12 + 7.625 in = 55.625 in
Add134.25 + 55.625 = 189.875 in
Feet and inches189.875 ÷ 12 = 15 ft, remainder 9.875 in → 15 ft 9 7/8 in to the nearest 1/16 in
Exact at the Nearest 1/16 in
The answer lands exactly on a 1/16 in mark, so the tape reading needs no rounding at all.

Feet and Inches Calculator Addition, Subtraction and Carry

Convert every length to inches, add or subtract, then split the total back into feet at 12 in per foot, by hand or in a feet and inches calculator. 11 ft 2 1/4 in plus 4 ft 7 5/8 in is 134.25 + 55.625 = 189.875 in, which is 15 ft 9 7/8 in.

L is the length in total inches, F is the feet and I is the inches, fraction included. A length of 4 ft 7 in is 12 × 4 + 7 = 55 in, and 2 ft 6 1/2 in is 30.5 in.

Going back, the feet are the whole number of times 12 fits into L, and the inches are what is left. 189.875 ÷ 12 is 15 with 9.875 in left over, and 0.875 in is 7/8 in on the tape.

Feet and inches calculator subtraction borrows a foot as 12 in. For 8 ft minus 2 ft 7 13/16 in, work 96 - 31.8125 = 64.1875 in, which is 5 ft 4 3/16 in.

A negative answer, such as 4 ft 7 5/8 in - 11 ft 2 1/4 in = -6 ft 6 5/8 in, means the lengths were taken in the wrong order.

Inches above 12 in a single entry carry on their own. A note that reads 3 ft 30 in is 66 in, or 5 ft 6 in, so a feet and inches calculator sum written that way is still correct.

The trap is rounding. Round the total inches to the tape fraction first, then split into feet. Splitting first and rounding the inches column alone turns a length just under a foot mark into "12 in".

Exact TotalRound Total, Then Split (1/16 in)Split, Then Round Inches
23 31/32 in2 ft1 ft 12 in
71.97 in6 ft5 ft 12 in
119.99 in10 ft9 ft 12 in
47.95 in3 ft 11 15/16 in3 ft 11 15/16 in

The last row shows why the error hides. It only appears when the inches round up to a full foot, so most adding feet and inches calculator results look fine until one lands near a foot mark.

Multiplying Feet and Inches: Area or Scaling

Two lengths multiplied give an area, so a feet and inches calculator product of two sides is in square units. 11 ft 2 1/4 in × 4 ft 7 5/8 in is 134.25 × 55.625 = 7,467.66 sq in, or 51.86 sq ft.

A is the area in square feet, and L1 and L2 are the two sides in inches. Divide by 1,296 instead for square yards, the unit carpet is sold in.

Typing feet and inches as a decimal is a common multiply feet and inches calculator error. A room of 11 ft 11 in by 13 ft 11 in is not 11.11 × 13.11 ft, and the gap grows as the inches grow.

RoomCorrect AreaTyped as DecimalsErrorDiagonal
8 ft 6 in × 9 ft 8 in82.17 sq ft84.28 sq ft+2.11 sq ft12 ft 10 7/16 in
10 ft 9 in × 12 ft 10 in137.96 sq ft131.89 sq ft-6.07 sq ft16 ft 8 7/8 in
11 ft 11 in × 13 ft 11 in165.84 sq ft145.65 sq ft-20.19 sq ft18 ft 3 7/8 in
14 ft 3 in × 16 ft 7 in236.31 sq ft238.81 sq ft+2.50 sq ft21 ft 10 3/8 in

The diagonal is the squaring check for a frame, slab or room. When both diagonals of the 10 ft 9 in × 12 ft 10 in rectangle measure 16 ft 8 7/8 in, the corners are square. Room totals carry on in the Square Footage Calculator.

Area divided by 32 sq ft gives a minimum count of 4 × 8 sheets, five for the 137.96 sq ft room, before any cut layout. The Square Yard Calculator takes the same sides for flooring sold by the yard.

A length times a plain number stays a length. 3 ft 6 in times 2.5 is 42 × 2.5 = 105 in, or 8 ft 9 in, with no square units involved.

Dividing a Length Into Equal Parts

Divide the total inches by the number of parts, then measure every mark from the start of the run. 10 ft 5 in split into 7 parts is 125 ÷ 7 = 17.857 in, or 1 ft 5 7/8 in at the nearest 1/16 in.

Stepping off the rounded part of a feet and inches calculator split instead stacks its rounding at every step. Each 1 ft 5 7/8 in step is 1/56 in too long, and by the sixth mark the stepped line sits 1/8 in past the true mark.

MarkMeasured From StartStepped OffMillimeters From Start
11 ft 5 7/8 in1 ft 5 7/8 in453.6 mm
22 ft 11 11/16 in2 ft 11 3/4 in907.1 mm
34 ft 5 9/16 in4 ft 5 5/8 in1,360.7 mm
45 ft 11 7/16 in5 ft 11 1/2 in1,814.3 mm
57 ft 5 5/16 in7 ft 5 3/8 in2,267.9 mm
68 ft 11 1/8 in8 ft 11 1/4 in2,721.4 mm

The drift changes with the split. Over a full run, 8 ft in 5 parts ends 1/16 in short, 10 ft in 7 parts ends 1/8 in short and 12 ft in 9 parts lands exactly, because 16 in is a whole tape mark.

Spacing items with a width, such as balusters or pickets, leaves equal gaps at both ends and between every item.

g is the gap, L is the space between posts, n is the item count and w is the item width. Fourteen 1 1/2 in balusters in 72 in leave (72 - 21) ÷ 15 = 3.4 in gaps, which is 3 3/8 in on a 1/16 in tape.

Nudging the baluster count in a feet and inches calculator estimate can land on a clean number. Fifteen of the same balusters in 70 1/2 in give exactly 3 in gaps, with the first baluster center 3 3/4 in from the post.

A length divided by a length gives a count, and every cut also removes one blade width. A board yields a whole piece only when each piece plus one kerf between cuts still fits inside it.

n is the count of whole pieces, A is the board, B is the piece and k is the kerf. Freud's catalog lists 1/8 in for its full-kerf blades, and its thin-kerf blades such as the LU87R010 cut 0.094 in, about 3/32 in.

CutPlain RatioWhole Pieces, 1/8 in KerfOffcut After Last Cut
10 ft ÷ 2 ft541 ft 11 1/2 in
8 ft ÷ 16 in651 ft 3 3/8 in
12 ft ÷ 3 ft432 ft 11 5/8 in
8 ft ÷ 23 15/16 in4.0131 ft 11 13/16 in
8 ft ÷ 14 1/2 in6.6268 1/4 in
15 ft 9 7/8 in ÷ 2 ft 8 1/4 in5.8952 ft 4 in

Any piece that divides the board evenly loses one piece to the kerf in a feet and inches calculator cut count. The 8 ft ÷ 23 15/16 in row hides it best, since four pieces leave 1/4 in spare but three 1/8 in kerfs need 3/8 in.

A thin-kerf blade at 3/32 in adds 1/32 in to each offcut per cut but changes none of the piece counts above, so the blade choice matters for offcut length, not for how many pieces come out.

Decimal Feet, Centimeters and Meters

Decimal feet are total inches divided by 12, and centimeters are inches times 2.54. NIST fixes the foot at exactly 0.3048 m, so one inch is exactly 25.4 mm and 189.875 in is 15.8229 ft, 482.28 cm or 4.8228 m.

A decimal point is not a feet-and-inches separator. The decimal part of a foot times 12 gives inches, so a decimal to feet and inches calculator result for 5.10 ft is not 5 ft 10 in.

Written AsActual Length
5.10 ft5 ft 1 3/16 in
6.6 ft6 ft 7 3/16 in
8.3 ft8 ft 3 5/8 in
12.11 ft12 ft 1 5/16 in

Tape fractions convert to tiny decimals of a foot, which is why plans and feet and inches calculator decimal results carry four places. Each value below is exact to the digits shown, using 25.4 mm per inch.

Fraction of an InchDecimal FeetMillimeters
1/16 in0.0052 ft1.6 mm
1/8 in0.0104 ft3.2 mm
1/4 in0.0208 ft6.3 mm
3/8 in0.0312 ft9.5 mm
1/2 in0.0417 ft12.7 mm
5/8 in0.0521 ft15.9 mm
3/4 in0.0625 ft19.0 mm
7/8 in0.0729 ft22.2 mm

Metric lengths come back to the tape the same way. In a feet and inches calculator to meters or to cm check, 1 m is 3 ft 3 3/8 in, 2.4 m is 7 ft 10 1/2 in, 2.5 m is 8 ft 2 7/16 in and 3 m is 9 ft 10 1/8 in.

The old US survey foot was retired on January 1, 2023. It differed from the 0.3048 m foot by 2 parts per million, about 0.024 in over 1,000 ft, so it only matters on legacy land survey records, never on a feet and inches calculator tape reading.

Stud Layout From a Measured Run

A wall needs the run divided by the stud spacing, rounded up, plus one stud. A 15 ft 9 7/8 in wall at 16 in on center is 189.875 ÷ 16 = 11.87, so 12 bays and 13 studs, with a last bay of 1 ft 1 7/8 in.

N is the stud count, L is the wall length in inches, s is the spacing and the brackets mean round up. Corners, door and window openings and doubled studs are added on top of N in any feet and inches calculator stud count.

Wall RunStuds at 16 in OCLast Bay at 16 inStuds at 19.2 in OCStuds at 24 in OCLast Bay at 24 in
8 ft71 ft 4 in652 ft
10 ft98 in862 ft
12 ft101 ft 4 in972 ft
15 ft 9 7/8 in131 ft 1 7/8 in1191 ft 9 7/8 in
20 ft161 ft 4 in14112 ft
24 ft191 ft 4 in16132 ft

The one-stud-per-foot rule of thumb gives 16 studs for the 15 ft 9 7/8 in wall. The three extra over the straight-run count of 13 are the usual allowance for corners and openings, not part of the layout.

Maximum spacing is set by code, not habit. IRC Table R602.3(5) allows 2×4 bearing studs at 24 in on center when they carry only a roof, but caps them at 16 in when they carry one floor.

Metric framing runs at 400 mm and 600 mm centers. BRANZ works the NZS 3604 top plate tables in both spacings, and the stud count follows the same round-up-plus-one rule as any feet and inches calculator layout.

Wall RunStuds at 400 mmLast Bay at 400 mmStuds at 600 mmLast Bay at 600 mm
2.4 m7400 mm5600 mm
3.0 m9200 mm6600 mm
3.6 m10400 mm7600 mm
4.8 m13400 mm9600 mm
6.0 m16400 mm11600 mm

A 400 mm layout on an imperial wall can leave a sliver bay. The 15 ft 9 7/8 in wall at 400 mm needs 14 studs with a last bay of only 7/8 in, and 600 mm gives 10 studs with the same 7/8 in bay, so drop that stud or shift the layout.

Plates take stock by length, not by studs, in a feet and inches calculator stock count. The same 15 ft 9 7/8 in wall needs two 8 ft boards per plate with 2 1/8 in left over, so a bottom plate plus a double top plate takes six boards.

Adding a List of Measurements

Add every measurement in inches and round once at the end. Four lengths of 5 ft 2 1/2 in, 3 ft 7 in, 28 3/4 in and 4 ft 5/8 in total 182.875 in, or 15 ft 2 7/8 in, with an average of 3 ft 9 3/4 in per piece.

In a list of lengths, a number with no foot or inch mark counts as inches, so 28 3/4 reads as 28 3/4 in. Write 2' 4 3/4" when the note means feet.

Rounding each piece before adding stacks the error. A feet and inches calculator multiple values total should carry the exact pieces, as the two cut lists below show.

Cut ListExact TotalEach Piece Rounded FirstOverrun
7 × 10 3/16 in, tape at 1/8 in5 ft 11 5/16 in5 ft 11 3/4 in7/16 in
12 × 2 ft 3 1/32 in, tape at 1/16 in27 ft 3/8 in27 ft 3/4 in3/8 in

The longest and shortest pieces flag a mismeasured opening when a set should match. On the four-piece list they are 5 ft 2 1/2 in and 2 ft 4 3/4 in, a spread of 2 ft 9 3/4 in.

Spreadsheet Formulas for Feet and Inches (Excel)

Keep total inches in one cell, round it with MROUND, then split it with INT and MOD. Splitting before rounding gives the same "5 ft 12 in" fault as the carry table near the top.

CellFormulaResult for 5 ft 11.97 in
C2 total inches=A2*12+B271.97
D2 rounded to 1/16 in=MROUND(C2,1/16)72
E2 feet and inches=TRIM(INT(D2/12)&" ft "&TEXT(MOD(D2,12),"# ??/??")&" in")6 ft 0 in
F2 decimal feet=C2/125.9975
G2 centimeters=C2*2.54182.8038

The "# ??/??" format reduces the fraction, so 15 ft 9.875 in reads as 15 ft 9 7/8 in. A fixed "# ?/16" format prints 9 14/16 in, and skipping MROUND sends 71.97 in to 5 ft 12 in.

For a feet and inches calculator Excel sheet with a column of cuts, keep column C in inches and sum it before the MROUND step, which applies the round-once rule from the list section.

Reading Tapes, Symbols and Quick Conversions

Each answer below runs on the 12 in foot and the exact 25.4 mm inch, the two constants behind every feet and inches calculator conversion.

How many inches are in a foot?

A foot has 12 inches, so 12 inches is exactly 1 foot. One inch is 1/12 ft, or 0.0833 ft, and 1 ft is 304.8 mm.

How can I write 62 inches in feet and inches?

62 inches is 5 ft 2 in, written 5′ 2″. Divide 62 by 12 to get 5 with 2 left over, the same split as any feet and inches calculator answer. As a decimal, 62 in is 5.1667 ft.

What is 4.5 feet in feet and inches?

4.5 feet is 4 ft 6 in. Multiply the decimal part by 12, so 0.5 × 12 = 6 in, and keep the 4 whole feet as they are.

What is 5 feet 10 inches in decimal feet?

5 feet 10 inches is 5.8333 ft. Convert to 70 total inches, then divide by 12. In metric it is 177.8 cm, from 70 × 2.54.

What are the symbols for feet and inches?

The prime ′ marks feet and the double prime ″ marks inches, as in 5′ 10″. Keyboards use the straight ' and " marks instead, and drawings often add a hyphen, as in 5'-10", so the inches cannot be misread.

How do you read a tape measure in construction?

Count the lines between inch marks. On a 1/16 in tape the longest line is the inch, then 1/2, 1/4, 1/8 and the shortest 1/16, so the 14th line past 9 in reads 9 14/16, or 9 7/8 in.

Many tapes also highlight every 16 in for stud layout. Read the inch number first, then the fraction lines past it, and convert the reading to total inches before any feet and inches calculator math.