Linear feet to square feet calculator math depends on true width: 100 LF of a 1×8 covers 60.42 sq ft, not 66.67, while deck gaps, room rows, carpet drops and waste change it again.
Use the face width each board covers, not its nominal size.
Gap, Waste, Boards and Price
Coverage Diagram
Linear Feet to Square Feet Chart
| Linear Feet | Square Feet | Square Yards |
|---|---|---|
| 1 LF | 0.5000 sq ft | 0.05556 sq yd |
| 10 LF | 5.000 sq ft | 0.5556 sq yd |
| 12 LF | 6.000 sq ft | 0.6667 sq yd |
| 20 LF | 10.00 sq ft | 1.111 sq yd |
| 25 LF | 12.50 sq ft | 1.389 sq yd |
| 40 LF | 20.00 sq ft | 2.222 sq yd |
| 50 LF | 25.00 sq ft | 2.778 sq yd |
| 100 LF | 50.00 sq ft | 5.556 sq yd |
| 200 LF | 100.0 sq ft | 11.11 sq yd |
| 500 LF | 250.0 sq ft | 27.78 sq yd |
| 1,000 LF | 500.0 sq ft | 55.56 sq yd |
By Material Width
| Material | Width | sq ft per LF | Your Area |
|---|---|---|---|
| 1×4 or 2×4 | 3.5 in | 0.2917 | 29.17 sq ft |
| 1×6, 2×6 or Deck | 5.5 in | 0.4583 | 45.83 sq ft |
| 1×8 or 2×8 | 7.25 in | 0.6042 | 60.42 sq ft |
| 1×10 or 2×10 | 9.25 in | 0.7708 | 77.08 sq ft |
| 1×12 or 2×12 | 11.25 in | 0.9375 | 93.75 sq ft |
| T&G 1×4 Face | 3.125 in | 0.2604 | 26.04 sq ft |
| T&G 1×6 Face | 5.125 in | 0.4271 | 42.71 sq ft |
| Shiplap 1×6 Face | 5 in | 0.4167 | 41.67 sq ft |
| Shiplap 1×8 Face | 6.75 in | 0.5625 | 56.25 sq ft |
| Carpet Roll, 12 ft | 12 ft | 12.00 | 1,200 sq ft |
| Carpet Roll, 15 ft | 15 ft | 15.00 | 1,500 sq ft |
| Your Width | 6 in | 0.5000 | 50.00 sq ft |
Step-by-Step Math
Linear Feet to Square Feet Calculator Formula and Width Factors
Square feet equal linear feet times the covered width in feet. A linear foot is one foot of length at any width, so it matches one square foot only when the material is exactly 12 in wide.
A is the area in square feet, L is the run in linear feet and W is the covered width in inches. Dividing by 12 turns inches into feet, so a width already in feet skips that step.
Take 100 LF of 6 in material: 100 × 0.5 = 50 sq ft. The same 100 LF of a 1×6 board, which is 5½ in wide, covers 45.83 sq ft, so for 100 linear feet to square feet the board name alone overstates the area by 4.17 sq ft.
| Linear Feet | 3½ in (1×4) | 5½ in (1×6) | 6 in | 12 in |
|---|---|---|---|---|
| 1 LF | 0.2917 sq ft | 0.4583 sq ft | 0.5000 sq ft | 1.000 sq ft |
| 10 LF | 2.917 sq ft | 4.583 sq ft | 5.000 sq ft | 10.00 sq ft |
| 12 LF | 3.500 sq ft | 5.500 sq ft | 6.000 sq ft | 12.00 sq ft |
| 20 LF | 5.833 sq ft | 9.167 sq ft | 10.00 sq ft | 20.00 sq ft |
| 25 LF | 7.292 sq ft | 11.46 sq ft | 12.50 sq ft | 25.00 sq ft |
| 40 LF | 11.67 sq ft | 18.33 sq ft | 20.00 sq ft | 40.00 sq ft |
| 100 LF | 29.17 sq ft | 45.83 sq ft | 50.00 sq ft | 100.0 sq ft |
| 200 LF | 58.33 sq ft | 91.67 sq ft | 100.0 sq ft | 200.0 sq ft |
| 1,000 LF | 291.7 sq ft | 458.3 sq ft | 500.0 sq ft | 1,000 sq ft |
Every row scales in a straight line, so 20 linear feet to square feet at 5½ in is 9.167 sq ft and 1000 linear feet to square feet is fifty times that. Any linear feet to square feet calculator estimate is only as good as the width behind it.
Metric runs follow the same rule. 100 m of a 140 mm board covers 100 × 0.14 = 14 m², or 150.7 sq ft, once converted, the width works in any linear feet to square feet calculator, and a Square Meter Calculator covers rooms measured in meters.
Dressed, Tongue-and-Groove and Shiplap Widths
Nominal size overstates coverage. Under the American Softwood Lumber Standard PS 20-20, Table 3, a dry 1×6 or 2×6 is dressed to 5½ in, a 1×8 to 7¼ in and a 1×12 to 11¼ in.
Matched boards lose more width. PS 20-20 Table 1 lists nominal 6 in flooring at a 5-1/8 in face, and Tables 2 and 4 put nominal 6 in shiplap at a 5 in face, because the tongue or lap hides under the next board.
| Board | Covered Width | sq ft per LF | LF per 100 sq ft |
|---|---|---|---|
| 4 in tongue-and-groove flooring | 3-1/8 in | 0.2604 | 384.0 |
| 1×4 or 2×4 | 3½ in | 0.2917 | 342.9 |
| 6 in shiplap | 5 in | 0.4167 | 240.0 |
| 6 in tongue-and-groove flooring | 5-1/8 in | 0.4271 | 234.1 |
| 1×6, 2×6 or deck board | 5½ in | 0.4583 | 218.2 |
| 8 in shiplap | 6-3/4 in | 0.5625 | 177.8 |
| 1×8 or 2×8 | 7¼ in | 0.6042 | 165.5 |
| 1×10 or 2×10 | 9¼ in | 0.7708 | 129.7 |
| 1×12 or 2×12 | 11¼ in | 0.9375 | 106.7 |
Take 200 linear feet of 6-inch boards. At the nominal 6 in they read 100 sq ft, at the dressed 5½ in they cover 91.67 sq ft, and as 5-1/8 in tongue-and-groove they cover 85.42 sq ft.
Buying 200 LF for a 100 sq ft wall on the nominal figure leaves 8.33 sq ft bare with square-edge 1×6 and 14.58 sq ft bare with tongue-and-groove, before a single cut is lost.
Measure the face on a laid board, joint to joint, rather than the loose board edge to edge. An Inch Fraction Calculator turns 5-1/8 in into 5.125 for the linear feet to square feet calculator math.
Area to Length: 100, 200 and 400 sq ft
Linear feet equal square feet divided by the covered width in feet. 200 sq ft of 1×6 board takes 200 ÷ 0.4583 = 436.4 LF, and 400 sq ft takes 872.7 LF before any waste.
L is the run in linear feet, A is the area in square feet and W is the covered width in inches. For sq ft to linear ft, a 10% waste allowance multiplies L by 1.1, so 436.4 LF becomes 480.0 LF to order.
| Area | 3½ in | 5-1/8 in | 5½ in | 7¼ in | 12 in |
|---|---|---|---|---|---|
| 100 sq ft | 342.9 / 377.1 LF | 234.1 / 257.6 LF | 218.2 / 240.0 LF | 165.5 / 182.1 LF | 100.0 / 110.0 LF |
| 200 sq ft | 685.7 / 754.3 LF | 468.3 / 515.1 LF | 436.4 / 480.0 LF | 331.0 / 364.1 LF | 200.0 / 220.0 LF |
| 400 sq ft | 1,371 / 1,509 LF | 936.6 / 1,030 LF | 872.7 / 960.0 LF | 662.1 / 728.3 LF | 400.0 / 440.0 LF |
| 1,000 sq ft | 3,429 / 3,771 LF | 2,341 / 2,576 LF | 2,182 / 2,400 LF | 1,655 / 1,821 LF | 1,000 / 1,100 LF |
Each cell's first figure is the net linear feet to square feet calculator run, and the second includes 10% waste. Square feet to linear feet has no single answer: 200 sq ft is 685.7 LF of 1×4, 331.0 LF of 1×8, or 200 LF of anything a full foot wide.
For flooring, the linear feet to square feet calculator result runs both ways, so a box labeled in square feet and a price quoted per linear foot can be compared on the same width.
Rooms From 10×10 to 20×20, Trim and Floor
Trim takes the perimeter and flooring takes the area. A 12×12 room needs 48 LF of baseboard, 2 × (12 + 12), but 324 LF of 5½ in boards laid in 27 full rows to cover its 144 sq ft.
Door openings come off the trim figure only. A 36 in door removes 3 LF of baseboard, while the floor still runs under it, and a Square Footage Calculator handles L-shaped or angled rooms.
| Room | Area | Perimeter | Area ÷ Width | Rows | Last Row | LF in Full Rows |
|---|---|---|---|---|---|---|
| 10 × 10 ft | 100 sq ft | 40 LF | 218.2 LF | 22 | 4.5 in | 220 LF |
| 10 × 12 ft | 120 sq ft | 44 LF | 261.8 LF | 27 | 1 in | 270 LF |
| 12 × 12 ft | 144 sq ft | 48 LF | 314.2 LF | 27 | 1 in | 324 LF |
| 12 × 14 ft | 168 sq ft | 52 LF | 366.5 LF | 31 | 3 in | 372 LF |
| 12 × 15 ft | 180 sq ft | 54 LF | 392.7 LF | 33 | 4 in | 396 LF |
| 14 × 16 ft | 224 sq ft | 60 LF | 488.7 LF | 35 | 5 in | 490 LF |
| 15 × 20 ft | 300 sq ft | 70 LF | 654.5 LF | 44 | 3.5 in | 660 LF |
| 20 × 20 ft | 400 sq ft | 80 LF | 872.7 LF | 44 | 3.5 in | 880 LF |
Boards run along the first dimension and rows stack across the second in every linear feet to square feet calculator room count. A 10×10 room therefore needs 40 LF of trim and 220 LF of 1×6 floor in 22 rows, and a 12×14 room needs 52 LF of baseboard.
Area ÷ width undercounts because the last row is bought whole. A 12 ft width holds 26.18 board widths, so row 27 is a 1 in rip, and a linear feet to square feet calculator area figure of 314.2 LF falls 9.8 LF short.
A 1 in strip splits when nailed. Ripping the first and last rows to (5.5 + 1) ÷ 2 = 3.25 in each keeps the same 27 rows and puts a sturdier piece against both walls.
Deck Gaps Add Coverage per Board
A gap widens what each deck board covers. The Trex installation guide calls for at least 3/16 in width-to-width, so a 5½ in board covers 5-11/16 in of deck instead of 5½ in.
Trex customer care states its Hideaway hidden fasteners set a 1/4 in gap, which brings the covered width to 5¾ in. Either gap trims the linear feet needed for the same deck area.
| Gap | Covered Width | LF for 200 sq ft | With 10% Waste | 12 ft Boards | 16 ft Boards | 20 ft Boards |
|---|---|---|---|---|---|---|
| None | 5.500 in | 436.4 LF | 480.0 LF | 40 | 30 | 24 |
| 3/16 in | 5.688 in | 422.0 LF | 464.2 LF | 39 | 30 | 24 |
| 1/4 in | 5.750 in | 417.4 LF | 459.1 LF | 39 | 29 | 23 |
A 200 sq ft deck in 5½ in boards takes 480.0 LF with waste and no gap, or 464.2 LF at 3/16 in. The gap saves 15.8 LF, about one 16 ft board, so the board count barely moves.
Row count is where the gap matters most in a linear feet to square feet calculator plan for decks. On a 16 × 12 ft deck with boards running the 16 ft way, 3/16 in gaps drop the rows from 27 to 26 and grow the last row from a 1 in rip to 1.81 in.
That gap-adjusted width belongs in every linear feet to square feet calculator figure for decking, since a tight-board estimate overbuys by the 3.4% to 4.5% that the gaps add to each row.
Carpet Drops on 12 ft and 15 ft Rolls
Carpet is bought by roll length, and each strip, called a drop, spans the room length. CRI 105, Section 5.3, adds at least 3 in along each wall for trimming.
That trim sets both directions of a linear feet to square feet calculator carpet count. Each drop is cut 6 in longer than the room, and a 12 ft roll covers a room only up to 11.5 ft wide in one piece, or 14.5 ft for a 15 ft roll.
N is the number of drops, B is the room width across the roll in feet and R is the roll width in feet. The carpet length is N × (room length + 0.5), and each extra drop adds a seam as long as the room.
| Room, Length × Width | Roll Width | Drops | LF Bought | sq yd Bought | Room sq yd |
|---|---|---|---|---|---|
| 15 × 12 ft | 12 ft | 2 | 31 LF | 41.33 | 20.00 |
| 15 × 12 ft | 15 ft | 1 | 15.5 LF | 25.83 | 20.00 |
| 15 × 14 ft | 12 ft | 2 | 31 LF | 41.33 | 23.33 |
| 15 × 14 ft | 15 ft | 1 | 15.5 LF | 25.83 | 23.33 |
| 14 × 15 ft | 15 ft | 2 | 29 LF | 48.33 | 23.33 |
| 15 × 11.5 ft | 12 ft | 1 | 15.5 LF | 20.67 | 19.17 |
| 12 × 12 ft | 12 ft | 2 | 25 LF | 33.33 | 16.00 |
| 12 × 12 ft | 15 ft | 1 | 12.5 LF | 20.83 | 16.00 |
| 12 × 14 ft | 15 ft | 1 | 12.5 LF | 20.83 | 18.67 |
| 20 × 16 ft | 12 ft | 2 | 41 LF | 54.67 | 35.56 |
| 20 × 16 ft | 15 ft | 2 | 41 LF | 68.33 | 35.56 |
A 12 × 15 room takes one 15.5 ft drop of 15 ft goods, 25.83 sq yd, or two drops of 12 ft goods, 41.33 sq yd with a 15 ft seam. Area alone reads 20 sq yd for both, which plain linear feet to square feet calculator division misses.
The second drop cannot be trimmed to a fill strip cut across the roll, because CRI 105 Section 5.2 requires adjacent pieces to share one pile direction. A 15 × 14 ft room on 12 ft goods reads 17.5 LF by area but buys 31 LF.
Roll direction matters too. Run the 15 × 14 ft room's drops along the 15 ft wall and one piece covers it; turn them the other way and the 15 ft width plus trim needs two drops, 48.33 sq yd.
The 6 in of trim per drop already covers wall cuts, so carpet takes no extra 10% waste unless a pattern needs matching. Carpet prices run per square yard, which a Square Yard Calculator converts from any room.
Stock Lengths, Offcuts and Price per Linear Foot
Rows shorter than the stock are counted row by row. A 12 × 12 ft floor in 1×6 has 27 rows of 12 ft, and each 16 ft board yields one row plus a 4 ft offcut too short to start the next row, so it takes 27 boards.
By length, the linear feet to square feet calculator total for the same floor is 324 LF × 1.1 = 356.4 LF, or 23 boards of 16 ft. The larger of the two counts is the buy.
| Stock Length | Boards by Length, 10% Waste | Boards Row by Row | Boards to Buy | LF Bought |
|---|---|---|---|---|
| 12 ft | 30 | 27 | 30 | 360 LF |
| 16 ft | 23 | 27 | 27 | 432 LF |
| 20 ft | 18 | 27 | 27 | 540 LF |
Stock that matches the run is the cheaper buy on a deck, where each butt joint must land on a joist and a 4 ft offcut rarely fits. Thirty 12 ft boards buy 360 LF with waste, against 432 LF of 16 ft stock.
Rows half the stock length or shorter pair up. A 10 × 10 ft room cut from 20 ft stock gets two 10 ft rows per board, so its 22 rows need 11 boards, and by length with 10% waste the buy is 13.
Price per linear foot converts to price per square foot by dividing by the covered width in feet. At $2.25 per LF, a 1×6 costs 2.25 ÷ 0.4583 = $4.91 per sq ft and a 1×8 costs $3.72 per sq ft.
| Price per LF | 3½ in, per sq ft | 5½ in, per sq ft | 7¼ in, per sq ft |
|---|---|---|---|
| $1.00 | $3.43 | $2.18 | $1.66 |
| $2.25 | $7.71 | $4.91 | $3.72 |
| $3.00 | $10.29 | $6.55 | $4.97 |
| $5.00 | $17.14 | $10.91 | $8.28 |
Wider boards cost less per square foot at the same linear foot price, which is why one linear feet to square feet calculator conversion settles a quote. A Cost Per Square Foot Calculator then compares it with labor.
Lineal Foot, Regular Foot and Board Foot
A linear foot is a length, a square foot an area and a board foot a volume, so one foot of 1×6 is 1 LF, 0.4583 sq ft and 0.5 board foot at the same time.
How many feet is 1 linear foot?
One linear foot is one foot, 12 in, measured along the material. Lineal and linear mean the same, so 12 linear feet is 12 ft and 40 ft of trim is 40 LF, whatever the width, which enters only at the linear feet to square feet calculator step.
Inches convert by dividing by 12, so 20 LF is 240 in and 66 in of trim is 5.5 LF. For mixed feet and inches, a Feet and Inches Calculator adds runs such as 11 ft 7-3/4 in.
What is the symbol for linear feet?
LF is the usual symbol on quotes, lumber tickets and linear feet to square feet calculator results, with lin. ft and the prime mark, as in 25′, also in use. A ticket line such as 25 LF 1×6 means 25 ft of board covering 11.46 sq ft at 5½ in.
How big is 100 linear feet?
100 linear feet is 100 ft of length, about 30.48 m. As area it depends on the width in the linear feet to square feet calculator math: 100 LF of 1×6 covers 45.83 sq ft, roughly a 6.77 ft square, while 10 LF of the same board covers 4.583 sq ft.
How do I calculate square feet from linear feet of fence?
Multiply the fence run by its height, which takes the place of width in a linear feet to square feet calculator. 100 LF of 6 ft fence is 600 sq ft per face, so staining both sides covers 1,200 sq ft, and gates count at their own height and width.
What's the difference between linear feet and board feet?
A board foot is 144 cubic inches, 1 in × 12 in × 12 in, figured on nominal size rather than the dressed width. So 100 LF of 2×6 is 100 board feet and 100 LF of 2×12 is 200, while each covers a different area.