Gravel Calculator

Updated

Gravel calculator for tons, cubic yards, bags and truck loads from area, depth and stone density, with an allowance for compaction and the delivered cost per square foot of ground.

Gravel Area and Depth

Measure the area to cover, then enter the finished gravel depth.

lb/ft³
%
Gravel Price and Delivery$45.00/ton, $100.00 delivery
$ flat
Gravel Bags and Truck Loads0.5 cu ft bags at $5.00, 13 tons per truck
$/bag
Gravel Needed
2.89 Tons to Order
5,775 lb, or 2.63 tons before the 10% extra
2.04 cu yd of Gravel
Cubic Feet55.00 cu ft
Cubic Meters1.56 m³
Area × depth gives the volume to fill. The 10% extra on top covers settling, compaction and spills.
0.71 cu yd per Ton
1 Ton Covers at 4 in57.1 sq ft
1 cu yd Weighs2,835 lb
Density sets how much space a ton fills. Ask your supplier for theirs, since wet or washed stone runs heavier.
$229.94 Delivered Cost
Gravel Only$129.94
Per sq ft$1.53
Order amount × your bulk price, plus the delivery fee. Labor, edging and landscape fabric are extra.
110 Bags of 0.5 cu ft
Bags Cost$550.00
Truck Loads (13 tons)1 Load, 22% Full
Each bag holds about 52.5 lb of this gravel. Bulk delivery saves $320.06 compared with buying the bags.
Gravel Area Diagram150.0 sq ft, 4 in deep
10 ft150.0 sq ft15 ft4.00 in deep: 2.89 tons / 2.04 cu yd
Gravel Needed by DepthFor 150.0 sq ft, 10% extra
Gravel Depth (Use)VolumeWeightBagsDelivered Cost
2 in (Decorative Beds)1.02 cu yd1.44 tons55$164.97
3 in (Walkways and Paths)1.53 cu yd2.17 tons83$197.45
4 in (Driveway Base Layer)2.04 cu yd2.89 tons110$229.94
6 in (Base + Thin Surface)3.06 cu yd4.33 tons165$294.91
Step-by-Step Gravel Math8 steps

Area15 ft × 10 ft = 150.00 sq ft

Volume before extra150.00 sq ft × (4 in ÷ 12) = 50.00 cu ft

Volume to order50.0000 cu ft × 1.1 = 55.00 cu ft ÷ 27 = 2.04 cu yd

Weight to order55.0000 cu ft × 105 lb/ft³ = 5,775 lb ÷ 2,000 = 2.89 tons

Coverage per ton2,000 lb ÷ 105 lb/ft³ = 19.05 cu ft ÷ (4 in ÷ 12) = 57.1 sq ft

Delivered cost2.8875 tons × $45 + $100.00 delivery = $229.94

Bags55.0000 cu ft ÷ 0.5 cu ft = 110.00, rounded up to 110 × $5 = $550.00

Truck loads2.8875 tons ÷ 13 tons = 0.22, rounded up to 1 load

Driveway Depth
A new driveway takes a 4 in (10 cm) base plus 2 to 4 in (5 to 10 cm) of surface stone. Spread and compact each layer before adding the next.

Gravel Calculator Formula and the Unit Traps

Gravel volume is area times depth, plus an allowance for settling and spills. Weight is that volume times the bulk density of the stone. Most gravel calculator errors come from mixing inches with feet, or US tons with metric tonnes.

V is the volume to order in cubic feet, A is the area in square feet, d is the depth in inches and e is the extra percent. Divide V by 27 to get cubic yards, the unit most bulk yards quote.

W is the weight in US short tons, and ρ is the bulk density in lb/ft³. Dry ¼ to 2 in gravel runs 105 lb/ft³, which is 1,682 kg/m³ in metric.

Take a 20 × 24 ft parking pad at 4 in deep. It covers 480 sq ft and holds 160 cu ft of stone. With 10% extra the order is 176 cu ft, or 6.52 cu yd, and it weighs 18,480 lb, which is 9.24 tons.

A metric supplier bills that same pile as 8.38 tonnes. A tonne is 2,204.6 lb and a US ton is 2,000 lb, so a tonne figure reads about 9% lower for identical stone. Divide gravel calculator tons by 1.1023 before comparing a price per tonne.

Weight per Cubic Yard by Stone Type

A cubic yard of dry ¼ to 2 in gravel weighs 2,835 lb, or 1.42 tons, in the Rockland Weights of Materials chart. The same gravel wet weighs 3,375 lb, which is 19% heavier for the same space.

Bulk figures like these drive every gravel calculator in tons, since loose stone includes the air between pieces.

Materiallb/ft³lb per cu ydTons per cu ydCu yd per tonTonnes per m³
Gravel, loose, dry952,5651.280.781.52
Limestone, broken96.52,6051.300.771.55
Crushed stone1002,7001.350.741.60
Granite, broken1032,7811.390.721.65
Gravel, dry, ¼-2 in1052,8351.420.711.68
Gravel with sand, natural1203,2401.620.621.92
Gravel, wet, ¼-2 in1253,3751.690.592.00

Pea gravel and ¾ in clean stone both fall inside the ¼ to 2 in size class, so 105 lb/ft³ fits a dry load of either. The Pea Gravel Calculator covers bag counts for rounded stone, and the Crushed Stone Calculator handles angular quarry stone.

The common 1.4 to 1.7 tons per yard range spans dry to wet ¼ to 2 in gravel only. Loose dry gravel at 1.28 and crushed stone at 1.35 sit below it, so a 1.5 figure in a gravel calculator by weight over-orders those by 17% and 11%.

Broken limestone at 1.30 tons per yard is lighter than most people guess for a dense rock. Voids between angular pieces take up space, so the Limestone Calculator uses bulk density, never the solid rock figure.

How Much Area Does One Ton of Gravel Cover?

One ton of dry ¼ to 2 in gravel covers 114.3 sq ft at 2 in deep and 57.1 sq ft at 4 in. Coverage halves each time depth doubles. It is the gravel calculator tons figure turned around, with area equal to 2,000 lb divided by density and depth.

DepthLoose dry gravel (95 lb/ft³)Crushed stone (100 lb/ft³)Dry ¼-2 in gravel (105 lb/ft³)Gravel with sand (120 lb/ft³)Wet gravel (125 lb/ft³)
1 in252.6 sq ft240.0 sq ft228.6 sq ft200.0 sq ft192.0 sq ft
2 in126.3 sq ft120.0 sq ft114.3 sq ft100.0 sq ft96.0 sq ft
3 in84.2 sq ft80.0 sq ft76.2 sq ft66.7 sq ft64.0 sq ft
4 in63.2 sq ft60.0 sq ft57.1 sq ft50.0 sq ft48.0 sq ft
6 in42.1 sq ft40.0 sq ft38.1 sq ft33.3 sq ft32.0 sq ft

The popular rule that a ton covers 100 sq ft at 2 in is exact only for gravel mixed with sand at 120 lb/ft³. It understates dry ¼ to 2 in gravel by 14% and overstates wet stone by 4%.

Those numbers are spread area with no allowance. A ton of dry gravel ordered with 10% extra finishes about 103.9 sq ft at 2 in, which is why the 100 sq ft rule still works as a rough gravel calculator by square foot check.

Driveway Depth Comes in Layers

A new gravel driveway takes a 4 in compacted base plus 2 to 4 in of surface stone, 6 to 8 in in total, per the Hello Gravel driveway depth guide. A single 4 in layer suits topping up an existing base, not building on bare soil.

The Stone Center driveway build guide runs 8 to 12 in across base, middle and surface layers for heavier traffic. On a 12 × 60 ft driveway, each extra inch of dry gravel adds about 3.47 tons.

Job (size, depth)AreaCubic yardsTons0.5 cu ft bags13-ton loads
Garden bed, 8 × 20 ft, 2 in160 sq ft1.091.54591
Walkway, 3 × 40 ft, 3 in120 sq ft1.221.73661
Patio pad, 12 × 12 ft, 4 in144 sq ft1.962.771061
Driveway base, 12 × 60 ft, 4 in720 sq ft9.7813.865282
Driveway surface, 12 × 60 ft, 2 in720 sq ft4.896.932641
Driveway total, 12 × 60 ft, 6 in720 sq ft14.6720.797922

All rows run gravel calculator math on dry ¼ to 2 in gravel at 105 lb/ft³ with 10% extra. Garden and pathway totals stay under 2 tons, so bags or one small delivery cover them.

The 13.86-ton driveway base lands just past one 13-ton truck and bills as two loads. Trimming the base to 3.75 in brings it to 12.99 tons and one load, but it thins the layer that carries the car.

A gravel calculator for driveway work fits the clean-stone surface layer best. A dense base course with fines is sized with the Road Base Calculator, and the layer under pavers with the Paver Base Calculator.

Round Beds, Triangles and Odd Shapes

A circle's area is pi times the diameter squared, divided by 4. A triangle's area is half its base times its height. After the area step, the depth, allowance and density math run exactly as for a rectangle.

D is the circle's diameter, b is the triangle's base and h is its height measured square to that base, all in feet. The triangle formula holds for any triangle as long as h is the perpendicular height.

A 10 ft tree ring at 3 in deep covers 78.5 sq ft. With 10% extra it needs 0.80 cu yd, or 1.13 tons, of dry gravel. A gravel calculator circle check matters here, since squaring the ring as 10 × 10 ft over-orders by 27%.

A 12 × 8 ft triangular corner bed at 2 in covers 48 sq ft. As a gravel calculator triangle job it needs 0.33 cu yd, or 924 lb with the allowance, about 18 of the 0.5 cu ft bags.

Split an L-shaped area into rectangles and add them. A 20 × 12 ft section plus a 10 × 8 ft leg makes 320 sq ft. At 3 in, that comes to 3.26 cu yd or 4.62 tons once the two areas are summed.

Bags Versus Bulk Delivery

Bagged gravel wins only on small jobs. At $5 per 0.5 cu ft bag against $45 per ton plus a $100 delivery fee, bags cost less up to about 13 cu ft, roughly half a cubic yard.

Order volume0.5 cu ft bagsBag costBulk + deliveryCheaper option
5 cu ft10$50.00$111.81Bags
10 cu ft20$100.00$123.62Bags
15 cu ft30$150.00$135.44Bulk
27 cu ft (1 cu yd)54$270.00$163.79Bulk
54 cu ft (2 cu yd)108$540.00$227.57Bulk

Those prices are sample figures. Local quotes move the break-even point but not the method, since bag cost rises in steps of one bag while bulk cost mostly carries the fixed delivery fee.

Bags sold by weight need one more conversion. A 50 lb bag of 105 lb/ft³ gravel holds 0.48 cu ft, so a cubic yard takes 57 of them, against 54 of the 0.5 cu ft size. Gravel calculator bag counts round up to whole bags.

Metric Orders in Tonnes and Cubic Meters

Gravel calculator results in metric use 1,682 kg/m³ for dry ¼ to 2 in gravel. At that density one tonne covers 11.9 m² at 5 cm deep and 5.9 m² at 10 cm, and one cubic meter spreads over 20 m² at 5 cm.

A 6 × 4 m driveway at 10 cm deep covers 24 m² and holds 2.40 m³ of stone. With 10% extra the order is 2.64 m³, or 4.44 tonnes, the figure a UK or European merchant would quote.

For a gravel calculator UK order, depth targets follow the same uses as in inches. About 5 cm covers decorative beds and chippings, while a driveway starts at 10 cm of base with surface stone laid on top.

Loam, Dirt and Sand by the Same Math

Dirt and sand use the same area, depth and density math as a gravel calculator, only with different densities. Dry excavated loam weighs 2,106 lb per cu yd, about 78 lb/ft³, so a ton of it fills more space than a ton of gravel.

Materiallb/ft³Tons per cu ydTons for 10 cu yd
Loam, dry, excavated781.0510.53
Earth, wet, excavated1001.3513.50
Sand, dry1001.3513.50
Sand, wet1201.6216.20
Gravel, dry, ¼-2 in1051.4214.18

Using a gravel density on a topsoil job overstates the tonnage by about 35%. Swap in 78 lb/ft³ for loam, or size it with the Yards Of Loam Calculator. Sand spread over an area is handled by the Sand Coverage Calculator.

Straight Answers on Tons, Depth and Cost

Each answer runs gravel calculator math on dry ¼ to 2 in gravel at 105 lb/ft³ with a 10% allowance, unless it names another stone, depth or rate.

What is a gravel ton calculator?

It is a gravel calculator in tons rather than cubic yards, since most quarries sell bulk stone by the ton off a truck scale. Tons equal cubic feet times density, divided by 2,000.

Moisture swings that weight. Five cubic yards of dry ¼ to 2 in gravel come to 7.09 tons, while the same 5 yards wet come to 8.44 tons. A per-ton price on wet stone buys about 16% less gravel.

Should I order gravel by the ton or cubic yard?

Order by the cubic yard when the stone is wet, and by the ton when it is dry and the yard has a scale. At $45 per ton, one cubic yard bills $63.79 dry but $75.94 wet, so tonnage pricing charges for the water.

How many tons of gravel do I need for a 10ft x 15ft driveway with a 4-inch depth?

You need 2.63 tons, or 1.85 cu yd, before any allowance, and 2.89 tons, or 2.04 cu yd, with 10% extra. The area is 150 sq ft, and 4 in is one third of a foot, so the volume is 50 cu ft.

A smaller 100 sq ft driveway patch at 2 in needs 0.68 cu yd with the same allowance. That is 0.96 tons, or 1,925 lb of dry gravel.

How much extra gravel should I order?

Order 5% to 10% extra for settling, spills and uneven ground, and lean toward 15% where the stone is compacted hard. On the 150 sq ft area at 4 in, 0%, 5%, 10% and 15% extra mean 2.63, 2.76, 2.89 and 3.02 tons.

Below 5%, a compacted layer usually finishes short of the target depth. A thin spot then needs a second delivery, which costs another full delivery fee for a small amount of stone.

How much is one truck load of gravel?

A 13-ton dump truck load holds about 9.17 cu yd of dry gravel. That covers about 1,486 sq ft at 2 in or 743 sq ft at 4 in.

At $45 per ton, the stone in a full load costs $585 before the delivery fee. Divide a gravel calculator yards total by 9.17 to get the number of loads.

Larger trucks carry more, so confirm the load size in tons or yards with the supplier. An order that runs slightly past one load, like the 13.86-ton driveway base, often costs a second trip.

How do you estimate the cost of gravel?

Multiply the order quantity by the unit price, then add delivery. For 2.89 tons at $45 per ton plus a $100 fee, the total is $229.94, or $1.53 per sq ft across 150 sq ft.

A price per cubic yard uses cubic yards in the first step instead of tons. Labor, edging and landscape fabric sit outside the stone cost, so add them as separate lines beside the gravel calculator estimator total.

How do you calculate gravel pressure?

The vertical pressure a gravel layer puts on the ground equals its density times its depth. Dry gravel at 105 lb/ft³ and 4 in deep loads the subgrade at 35 psf, or 0.24 psi. A full foot of it adds 105 psf.

Sideways pressure on a retaining wall is smaller and uses an active earth pressure coefficient from the Rankine formula.

Here φ is the friction angle of the stone. At an assumed 35°, Ka is 0.27, so gravel backfill 3 ft deep pushes about 85 psf at the base of the wall. Wall design itself belongs to an engineer.