Steel Weight Calculator

Updated

Steel Weight Calculator for round, square, hex and flat bar, pipe, tube, plate, angle, W beams and C channels in 9 grades, finding weight per foot or meter, length, and steel cost.

Quick Setup

Pick the steel type and shape, then enter the size and length.

pcs
Find Length From WeightSteel weight
Price and Cost$64.07 at $1.20 per lb
Weight of 1 Piece
53.39 lb Steel Weight
24.22 kg, Carbon Steel at 489.44 lb/cu ft
2.67 lb per Foot
Per Meter8.76 lb
Feet per US Ton749.2 ft
Cross-section area times density gives the weight of every foot or meter of this steel.
0.7854 sq in Cross-Section
In Square Centimeters5.07 cm²
Steel Volume0.109 cu ft
The steel area you would see if you cut the piece square across, the base of every weight.
5.236 sq ft Surface Area
Per Foot0.2618 sq ft
In Square Meters0.486 m²
The outside face area to paint or coat over the full length, with the hollow inside listed.
$64.07 Steel Cost
Cost per Foot$3.20
Cost per kg$2.65
Your price times the weight, the length or the piece count, whichever basis you picked.
Live Cross-Section DiagramRound Bar, 0.7854 sq in
Steel Weight Chart by SizeBy diameter, Carbon Steel
Weight by Steel Type9 steel types compared
Step-by-Step Steel Weight MathWith your numbers
    Steel Weight Found
    This is the nominal weight. Mill sizes run within a rolling tolerance, so a scale weight can read a little different.

    Cross-Section Area, the Steel Weight Calculator Starting Point

    Every square inch of steel cross-section weighs 3.40 lb per foot of length at 490 lb/ft³. Find the area of the shape, multiply by 3.40 and by the length in feet, and the steel weight calculator total follows.

    W is the steel weight calculator result, A the cross-section area, L the length, rho the steel density and n the piece count. With inches and 0.2836 lb/in³, the answer is in pounds.

    In metric, each square centimeter of section weighs 0.785 kg per meter at 7,850 kg/m³. A 50 × 50 × 5 mm angle has about 4.75 cm² of steel, so it weighs close to 3.73 kg/m.

    The 7,850 kg/m³ figure equals 490 lb/ft³, the steel density in the Iowa DOT rules for computing structural steel weight. Steel weight calculator charts below use it, the C1020 HR row in the density list.

    Some lists give carbon steel as 7,840 kg/m³, 0.13% lower. A 1 in round bar 20 ft long weighs 53.39 lb at 7,840 and 53.46 lb at 7,850, a gap of only 0.07 lb.

    Rebar and Round Bar per Foot and per Meter

    A #4 rebar weighs 0.668 lb per foot, and a 1 in round bar 2.673 lb per foot. Round bar area is π × d² ÷ 4, so a steel weight calculator per foot result climbs with the square of the diameter.

    US rebar weights from round-bar steel weight calculator math match the published nominal weights to within 0.2%. The Caltrans Bridge Design Details reinforcement chapter lists those nominal diameters and weights.

    BarNominal Diameter (in)Round-Bar Math (lb/ft)Published Weight (lb/ft)20 ft Bar (lb)kg/m
    #30.3750.3760.3767.50.559
    #40.5000.6680.66813.40.994
    #50.6251.0441.04320.91.554
    #60.7501.5031.50230.12.237
    #70.8752.0462.04440.93.045
    #81.0002.6732.67053.53.978
    #91.1283.4013.40068.05.061
    #101.2704.3114.30386.26.416
    #111.4105.3145.313106.37.908
    #141.6937.6617.650153.211.401
    #182.25713.61613.600272.320.262

    Bar numbers stop matching eighths of an inch at #9. A #9 bar is 1.128 in, not 1 1/8 in, and a #10 is 1.270 in, so read the nominal diameter rather than the bar number.

    Metric round bar uses d² ÷ 162 in kg per meter, with d in millimeters. Exact steel weight calculator in kg math and the rule agree within 0.2% from 6 to 40 mm.

    Diameter (mm)Exact (kg/m)d² ÷ 162 (kg/m)12 m Bar (kg)Meters per Tonne
    60.2220.2222.664,505
    80.3950.3954.742,534
    100.6170.6177.401,622
    120.8880.88910.651,126
    161.5781.58018.94634
    202.4662.46929.59406
    253.8533.85846.24260
    326.3136.32175.76158
    409.8659.877118.38101

    Flat, Square and Hex Bar Charts

    A 1 in square steel bar weighs 3.403 lb per foot, a 1 in hex bar 2.947 lb and a 1 in round bar 2.673 lb. Square stock adds 27% to a steel weight calculator result over round of the same width, and hex 10%.

    Size (in)Square (lb/ft)Hex, Across Flats (lb/ft)Round (lb/ft)
    1/40.2130.1840.167
    3/80.4790.4140.376
    1/20.8510.7370.668
    3/41.9141.6581.503
    13.4032.9472.673
    1 1/27.6576.6316.014
    213.61311.78910.691
    330.62926.52524.056
    454.45147.15642.766

    Flat bar steel weight calculator math is width × thickness × 3.40 lb/ft per square inch. A 2 × 1/4 in flat weighs 1.702 lb per foot, and a 20 ft length 34.0 lb.

    Flat Bar (in)lb/ft20 ft (lb)
    1 × 1/80.4258.5
    1 × 1/40.85117.0
    1 1/2 × 1/41.27625.5
    2 × 1/41.70234.0
    2 × 3/82.55251.0
    3 × 1/25.105102.1
    4 × 1/26.806136.1
    6 × 1/210.210204.2
    4 × 113.613272.3

    Two flats with the same area weigh the same whatever their proportions. A 2 × 3/8 in bar and a 3 × 1/4 in bar both carry 0.75 sq in and weigh 2.552 lb per foot. Wide plate sold by area is covered by the Steel Plate Weight Calculator.

    Hollow Tube With Sharp or Rounded Corners

    A 4 × 4 × 1/4 in square steel tube weighs 12.76 lb per foot with sharp corners and 12.21 lb with mill corners. Cold-formed tube is bent around a radius, about twice the wall outside and one wall inside.

    Steel Tube (in)Sharp Corners (lb/ft)Rounded Corners (lb/ft)Sharp Reads High By
    1 × 1 × 0.0650.830.794.7%
    1 1/2 × 1 1/2 × 0.1202.252.135.9%
    2 × 2 × 1/83.193.054.5%
    2 × 2 × 1/45.965.4110.1%
    3 × 3 × 3/167.186.874.5%
    4 × 4 × 1/412.7612.214.5%
    6 × 6 × 3/828.7127.484.5%
    3 × 2 × 3/165.905.595.5%
    4 × 2 × 1/49.368.816.2%
    6 × 4 × 1/416.1715.623.5%

    Thick walls on small tube widen the gap. A 2 × 2 × 1/4 in tube reads 10.1% heavy with sharp corners, because its four corners are a large share of a short perimeter, so use the rounded figure for a steel tube weight calculator order.

    Round tube and pipe have no corners to argue over. Their area is π ÷ 4 × (OD² - ID²), and the Pipe Weight Calculator carries the standard Schedule 40 and 80 sizes.

    Equal and Unequal Angle Weight

    A 2 × 2 × 1/4 in steel angle weighs 3.19 lb per foot by steel angle weight calculator math. The two legs share one corner square, so one thickness comes off the leg total before multiplying by the thickness.

    Here a and b are the leg lengths and t is the thickness. The formula treats the inside corner as square; rolled angle has a small root fillet that adds steel and rounded toes that remove some.

    Angle (in)Area (sq in)lb/ft20 ft (lb)kg/m
    1 × 1 × 1/80.2340.8016.01.19
    1 1/2 × 1 1/2 × 3/160.5271.7935.92.67
    2 × 2 × 1/80.4841.6533.02.45
    2 × 2 × 1/40.9383.1963.84.75
    3 × 3 × 1/41.4384.8997.87.28
    4 × 4 × 3/82.8599.73194.614.48
    4 × 4 × 1/23.75012.76255.218.99
    3 × 2 × 1/41.1884.0480.86.01
    4 × 3 × 3/82.4848.45169.112.58
    6 × 4 × 1/24.75016.17323.324.06

    Doubling the angle thickness does not double the steel weight calculator result. Going from 2 × 2 × 1/8 to 2 × 2 × 1/4 raises the weight from 1.65 to 3.19 lb per foot, 93% more, because the shared corner square grows with the thickness.

    Wide-Flange Beams and Channels by Size Name

    A W8x31 beam weighs 31 lb per foot, and a C10x15.3 channel 15.3 lb per foot. The number after the "x" in an AISC size is the weight per foot, so a 20 ft W8x31 weighs 620 lb.

    Dividing that nominal weight by 3.40 gives the steel area, as 31 ÷ 3.40 = 9.11 sq in. A named beam's steel weight calculator figure is the catalog weight at 7,850 kg/m³ and sits 0.13% lower at 7,840.

    SectionArea From Name (sq in)lb/ft at 7,850lb/ft at 7,84020 ft (lb)kg/m
    W6x123.5312.0011.98240.017.86
    W8x185.2918.0017.98360.026.79
    W8x319.1131.0030.96620.046.13
    W10x226.4722.0021.97440.032.74
    W12x267.6426.0025.97520.038.69
    W16x319.1131.0030.96620.046.13
    W18x4011.7640.0039.95800.059.53
    W24x6819.9868.0067.911,360.0101.20
    C3x4.11.204.104.0982.06.10
    C6x8.22.418.208.19164.012.20
    C8x11.53.3811.5011.49230.017.11
    C10x15.34.5015.3015.28306.022.77
    C12x20.76.0820.7020.67414.030.80
    C15x5014.6950.0049.941,000.074.41

    Depth and weight are separate choices. A W8x31 and a W16x31 weigh the same per foot, but the 16 in beam is twice as deep and far stiffer for the same steel, which matters more to the design than to the scale.

    Beams sized from flange and web dimensions come out slightly light. A W8x31 at 8 × 8 in with 0.435 in flanges and a 0.285 in web gives 30.60 lb/ft with square corners, 1.3% under 31, since rolled beams carry web fillets.

    Here bf is the flange width, tf the flange thickness, d the depth and tw the web thickness. The same area formula covers a channel when bf is measured to the outside of the web.

    Kilograms per Foot and Feet per Ton

    A #4 rebar weighs 0.303 kg per foot, and one US ton of it runs 2,993 ft. Mixed units like kg per foot come up when imperial stock is billed in metric, a common steel weight calculator in feet question, so each line below converts both ways.

    Sectionlb/ftkg/ftFeet per US TonMeters per Tonne
    #4 rebar0.6680.3032,9931,006
    2 × 1/4 in flat1.7020.7721,175395
    1 in round2.6731.212748251
    2 × 2 × 1/8 in tube, rounded3.0541.385655220
    2 × 2 × 1/4 in angle3.1901.447627211
    NPS 2 Sch 40 pipe3.6571.659547184

    Any steel weight calculator in kg ft figure is lb/ft × 0.4536. A metric tonne holds 10.2% more steel than a US ton, so the meters-per-tonne figure is not simply feet-per-ton divided by 3.28.

    Density From Tool Steel to Stainless

    Grade moves a steel weight calculator total by only a few percent, whatever the shape. A 1 in round bar 20 ft long weighs 52.54 lb in tool steel at 7,715 kg/m³, 53.46 lb at 7,850 and 54.68 lb in stainless at 8,030 kg/m³.

    Steel TypeDensity (kg/m³)1 in Round (lb/ft)20 ft Bar (lb)20 ft Bar (kg)
    Tool Steel7,7152.62752.5423.83
    Wrought Iron7,7502.63952.7823.94
    Carbon Tool Steel7,8202.66353.2524.16
    Cold-Drawn Steel7,8302.66653.3224.19
    Carbon Steel7,8402.66953.3924.22
    C1020 HR Steel7,8502.67353.4624.25
    Pure Iron7,8602.67653.5324.28
    Mild Steel7,8702.68053.5924.31
    Stainless Steel8,0302.73454.6824.80

    Stainless steel weight calculator in kg totals run 2.3% above the 7,850 figure. On a 2,000 lb carbon steel order, the same sizes in stainless come to about 2,046 lb.

    Mild steel is low-carbon steel, so for steel weight calculator purposes it shares the carbon steel figure. The 7,840, 7,850 and 7,870 entries differ by under 0.4%, or about 0.2 lb on a 20 ft bar of 1 in round.

    Length From a Known Weight

    One US ton of #4 rebar is 2,993 ft, or about 150 bars at 20 ft. Length is the weight divided by the weight per foot, the same steel weight calculator per foot figure run backward.

    The same step sizes offcuts and stock. A 100 lb scrap allowance of 2 × 1/4 in flat bar is 58.8 ft of steel, and one metric tonne of 12 mm bar is 1,126 m, or about 94 bars 12 m long.

    Ordering by weight and cutting by length are linked through this one steel weight calculator number. Check it before a cut list is quoted, since a 2% density difference becomes a 2% length difference on the floor.

    Paint Area and Price per Foot

    A 2 × 2 × 1/8 in square tube with rounded corners has 0.631 sq ft of outside surface per foot. A 20 ft length needs 12.6 sq ft of paint, before the inside is counted.

    Round bar paints at π × d per foot of length. A 1 in bar has 0.262 sq ft per foot, so 20 ft of it needs 5.24 sq ft of coating.

    Steel sold by the pound converts to a price per foot through the steel weight calculator weight per foot. At an example $0.75/lb, 1 in round bar costs $2.00 per foot, since it weighs 2.673 lb per foot.

    The $0.75 is a placeholder, so use a current supplier quote. A price per kilogram multiplies by 0.4536 to give a price per pound, the most common slip in mixed-unit quotes.

    Everyday Steel Weight Lookups

    These steel weight calculator replies use 7,850 kg/m³ (0.2836 lb/in³), with nominal sizes and sharp corners unless rounded corners are named.

    What is a steel weight calculator?

    A steel weight calculator is an estimate of steel weight from a section's shape, sizes, length and density. Its math is cross-section area × length × density, multiplied by the piece count.

    A 17 × 17 mm square bar 1.2 m long holds 0.0003468 m³ of steel, which weighs 2.72 kg. Twenty of those bars weigh 54.45 kg, the figure to plan a lift or a delivery around.

    How do I find the weight of steel?

    Multiply the cross-section area by the length and by 0.2836 lb/in³, or by 7,850 kg/m³ in metric. A 2 in round bar 12 ft long holds 452.4 cu in and weighs 128.3 lb.

    The same method works for any metal weight once the density changes, the steel weight formula with a new density. A 16 mm steel bar 6 m long weighs 9.47 kg, and in aluminum at 2,700 kg/m³ the same bar would weigh 3.26 kg.

    How much does steel weigh compared to other metals?

    Steel at 7,850 kg/m³ weighs about 2.9 times as much as aluminum, 1.7 times titanium, and roughly 88% of copper. A 1 in round bar 20 ft long weighs 53.46 lb in steel and 18.39 lb in aluminum.

    The same bar weighs 30.71 lb in titanium, 57.88 lb in brass and 61.02 lb in copper. The Metal Weight Calculator carries 34 metals, and the Aluminum Weight Calculator covers aluminum alloys.