Brick Veneer Calculator

Updated

Brick veneer calculator for full brick and thin brick walls that turns wall size and brick size into bricks or flats, corners, mortar bags, wall ties, weep holes, courses and cost.

Wall and Brick Setup

Measure the brick face of each wall, then subtract doors, windows and other openings.

%
Brick Dimensions and Mortar7 5/8 in × 2 1/4 in, 1 wythe
bricks
Brick Prices and Labor$650.00/1,000, $12.00/sq ft labor
$/bag
$/corner
Brick Veneer Needed
1,962 Bricks to Order
1,783 bricks cover 260 sq ft, plus 179 for 10% waste
6.86 Bricks per sq ft
Per m²73.81
Bricks per cu ft of Wall22.7
Each brick fills its face plus one mortar joint on its length and height, so the joint size changes the count.
54 Bags of Mortar, 80 lb
Wall Ties, Field and Openings110
Weep Holes at 24 in16
Mortar scales from 37 modular bricks per bag. Ties meet the area, spacing and opening rules for anchored veneer.
$1,788.30 Material Cost
Installed Estimate$4,908.30
Installed per sq ft$18.88
Material counts every brick ordered, waste included. The installed figure adds your mason labor rate on net wall area.
45 Full Courses of Brick
Course Height2 5/8 in
Gap Above Last Course1 7/8 in
Courses stack one brick height plus one joint. Any gap at the top needs a cut course or a small joint change.
Brick Bond Close-Up7 5/8 in × 2 1/4 in face
7 5/8 in face, 3/8 in joint2 5/8 in course
Bricks Needed by Brick SizeFor 260 sq ft net
Brick SizePer sq ftBricksWith 10% WasteMortar Bags
Modular, 2 1/4 in × 7 5/8 in6.861,7831,96254
Standard, 2 1/4 in × 8 in6.551,7041,87453
Queen, 2 3/4 in × 7 5/8 in5.761,4981,64847
Engineer Standard, 2 3/4 in × 8 in5.51,4311,57447
King, 2 5/8 in × 9 5/8 in4.81,2481,37346
Norman, 2 1/4 in × 11 5/8 in4.571,1891,30850
Closure, 3 5/8 in × 7 5/8 in4.51,1701,28740
Utility, 3 5/8 in × 11 5/8 in378085836
Saxon, 2 1/4 in × 15 5/8 in3.4389298148
Roman Maximus, 1 5/8 in × 23 5/8 in378085858
India Modular, 3.543 in × 7.48 in4.681,2171,33940
India Standard, 2.756 in × 9.055 in4.881,2691,39554
Step-by-Step Brick Math16 steps
Wall area30 ft × 10 ft = 300 sq ft
Net area300 - 40 = 260 sq ft
Brick module(7.625 + 0.375) in × (2.25 + 0.375) in = 21 sq in
Bricks per sq ft144 ÷ 21 = 6.8571
Bricks to cover260 × 6.8571 = 1,782.86, rounded up to 1,783
Bricks to order1,782.8571 × 1.1 = 1,961.14, rounded up to 1,962
Mortar per brick((7.625 + 0.375) × 0.375 + 2.25 × 0.375) × 3.625 = 13.9336 cu in
Bricks per bag37 × 13.9336 cu in ÷ 13.9336 cu in = 37
Mortar bags1,961.14 ÷ 37 = 53, rounded up to 54
Ties by area260 ÷ 2.67 sq ft = 97.38, rounded up to 98
Ties by spacing(360 in ÷ 32 in, rounded up = 12) × (120 in ÷ 24 in, rounded up = 5) = 60, so field ties = 98
Ties at openings36 ft of opening edge ÷ 3 ft = 12, rounded up to 12, total 110
Weep holes360 in ÷ 24 in = 15, rounded up to 15 spaces + 1 = 16
Courses120 in ÷ 2.625 in = 45.714 courses
Brick cost1,962 × $650.00 ÷ 1,000 = $1,275.30
Installed estimate$1,788.30 + 260 sq ft × $12.00 = $4,908.30
Wall Height Lands Between Courses
45 full courses reach 9 ft 10 1/8 in. A joint of 0.359 in fits 46 courses exactly, with no cut course at the top.

Brick Veneer Calculator Counts per Square Foot by Brick Size

A modular brick lays at 6.86 per sq ft with a 3/8 in mortar joint, a king brick at 4.80 and a utility brick at 3.00. Brick size sets a brick veneer calculator count far more than any waste allowance, so it is the first number to pin down.

In brick veneer calculator math, n is bricks per square foot of wall face, l and h are the brick's face length and height in inches, and j is the mortar joint. Each brick occupies its face plus one joint along its length and one along its height.

For a modular brick, (7 5/8 + 3/8) × (2 1/4 + 3/8) = 8 × 2.625 = 21 sq in, and 144 ÷ 21 = 6.86 bricks per square foot. That matches the published count in Glen-Gery's brick calculator for every US size below.

BrickFace SizeBricks per sq ftBricks per m²Bricks per 1,000 sq ft
Modular2 1/4 × 7 5/8 in6.8673.816,858
Standard2 1/4 × 8 in6.5570.56,551
Queen2 3/4 × 7 5/8 in5.76625,760
Engineer Standard2 3/4 × 8 in5.5059.225,503
King2 5/8 × 9 5/8 in4.8051.674,800
Norman2 1/4 × 11 5/8 in4.5749.214,572
Closure3 5/8 × 7 5/8 in4.5048.444,500
Saxon2 1/4 × 15 5/8 in3.4336.93,429
Utility3 5/8 × 11 5/8 in3.0032.293,000
Roman Maximus1 5/8 × 23 5/8 in3.0032.293,000
India Modular, 10 mm joint90 × 190 mm4.65504,646
India Standard, 10 mm joint70 × 230 mm4.8452.084,839

The "7 bricks per square foot" rule is a rounded modular figure. Used for king brick it overbuys by 46%, since a king face covers 30 sq in with its joint against 21 sq in for modular.

Any brick veneer calculator square feet estimate therefore starts from the real brick size, not a single rule of thumb carried across every brick.

Joint width moves the brick veneer calculator count too. On 1,000 sq ft of modular brick, a 1/4 in joint needs 7,315 bricks, a 3/8 in joint 6,858 and a 1/2 in joint 6,445, a spread of 870 bricks from joint size alone.

Published US counts assume the 3/8 in joint. A brick veneer calculator result with a different joint differs from a supplier's chart for that reason, not because either one is wrong.

Bricks Needed for 200, 500 and 1,000 sq ft Walls

A 200 sq ft wall of modular brick needs 1,372 bricks before waste and 1,509 with 10% added. At 1,000 sq ft that grows to 7,543 modular bricks to order, or 5,280 king bricks for the same wall.

Net Wall AreaModularQueenKingNormanUtility
100 sq ft755634528503330
200 sq ft1,5091,2681,0561,006660
500 sq ft3,7723,1682,6402,5151,650
1,000 sq ft7,5436,3365,2805,0293,300
2,000 sq ft15,08612,67210,56010,0586,600

Every brick veneer calculator figure in the table includes 10% waste on net wall area, with doors and windows already removed. A wall with many corners, openings or pattern cuts needs closer to 20%, which adds about 686 modular bricks per 1,000 sq ft.

A 30 × 10 ft wall with 40 sq ft of openings leaves 260 sq ft of brick face. In a brick veneer calculator for walls, 260 × 6.857 = 1,782.9, so 1,783 modular bricks cover it and 1,962 are the order with 10% waste.

Gross area overstates a brick veneer calculator order. The same wall without the 40 sq ft deduction would order 2,263 bricks, 301 more, so measure every window and door wider than a brick or two before the count goes to the supplier.

Coursing a Wall Height Without a Cut Course

A 10 ft wall in modular brick fits 45 full courses with 1 7/8 in left at the top. Opening each bed joint to 0.359 in, a hair under 3/8, lands exactly 46 courses with no cut course.

For brick veneer calculator coursing, c is the number of courses, H is the wall height in inches, h is the brick height and j is the bed joint. Modular brick courses at 2 5/8 in, so 120 ÷ 2.625 = 45.71 courses on a 10 ft wall.

BrickWall HeightFull Courses at 3/8 inGap at TopJoint for Exact FitCourses
Modular8 ft361 1/2 in0.345 in37
Modular9 ft413/8 in0.384 in41
Modular10 ft451 7/8 in0.359 in46
Queen10 ft381 1/4 in0.408 in38
King8, 9 or 10 ft32, 36 or 400 in3/8 in32, 36 or 40

King brick courses at exactly 3 in with a 3/8 in joint, four courses per foot, so 8, 9 and 10 ft walls all close without adjustment. That even coursing is one reason a brick veneer calculator for exterior walls often favors king brick on standard wall heights.

Joint adjustments in a brick veneer calculator layout stay small. Holding the bed joint between about 1/4 and 1/2 in keeps the wall looking uniform, so a gap that needs a bigger change is better solved with a cut course hidden under a window sill or soffit.

The Brick Course Height Calculator works the same coursing for any brick and joint when the wall height is fixed and the course count has to fit it.

Mortar Bags, Wall Ties and Weep Holes

An 80 lb bag of mortar mix lays about 37 modular bricks, so the 260 sq ft example wall takes 54 bags. It also needs 110 wall ties, 98 across the wall and 12 around openings, and 16 weep holes along its 30 ft base at 24 in spacing.

The Quikrete Mortar Mix data sheet says an 80 lb bag "will lay up to 37 standard bricks" as Type N mortar to ASTM C270. Larger bricks carry more mortar per piece, so brick veneer calculator bricks per bag drop as size grows.

BrickBricks per 80 lb BagBags per 1,000 BricksBags per 1,000 sq ft, 10% Waste
Modular3728204
Queen35.329180
King3034176
Norman26.638189
Utility24.342136

Per brick, a utility unit takes half again the mortar of a modular one. Per square foot of wall it takes less, 136 bags per 1,000 sq ft against 204, because three utility bricks replace almost seven modular ones and far fewer joints get filled.

Brick Industry Association Technical Note 28 limits each veneer anchor to 2 2/3 sq ft of wall, at no more than 32 in across and 24 in up under the IRC. It adds anchors within 12 in of any opening larger than 16 in, at 3 ft spacing.

Both limits apply at once, so the wall tie count is the larger of the area rule and the 32 × 24 in grid. On the 30 × 10 ft wall the grid gives 12 × 5 = 60 ties, so the area rule's 98 governs.

Short walls flip that. A 100 ft brick strip 6 in tall covers only 50 sq ft, which the area rule puts at 19 ties, yet a tie every 32 in along 100 ft needs 38, double the area count.

Opening ties come on top of the main wall count. The example wall's 3 × 7 ft door and 4 × 4.75 ft window have 37.5 ft of edge, and about 36 ft of that needs a tie every 3 ft, which adds 12 ties for 110 in all.

For a brick veneer calculator weep count, weeps sit directly above the base flashing, at least 3/16 in across and no more than 33 in apart.

BIA prefers open head-joint weeps at 24 in or less, which puts 16 weeps on the 30 ft example wall instead of 12 at the 33 in maximum.

Full brick veneer is 3 5/8 in thick, the brick veneer thickness used for mortar and tie math, set over a 1 in minimum air space.

The IRC table in that same BIA note caps anchored veneer at 5 in nominal thickness, 50 psf and 30 ft high in Seismic Design Categories A to C.

Mortar for a veneer job can also be site-mixed from cement, lime and sand. The Mortar Calculator splits a bag count into those materials for brick or block walls.

Thin Brick Flats and Corner Pieces

A thin brick wall needs one L-shaped corner piece per course on every outside corner. In a brick veneer calculator corner count, twenty vertical feet of modular-height thin brick takes 92 corner pieces, or 101 with 10% waste.

Nc is the corner piece count, Lc is the total vertical length of outside corners in feet, h is the thin brick height, j is the joint and w is the waste as a decimal. Modular-height thin brick runs 4.57 courses per foot.

Outside Corner LengthCorners Before WasteCorners With 10%
8 ft, one corner3741
20 ft92101
40 ft183202
80 ft366403

A thin brick veneer corner calculator count is measured in vertical feet, not wall area. Add the height of every outside corner, so a house with four 10 ft corners has 40 ft of corners and needs 202 pieces at 10% waste.

Brick veneer calculator flats are counted on the full net area without subtracting the corner pieces. On the 260 sq ft example wall that leaves 1,962 flats plus 101 corners, and the overlap at each corner turns into a few spare flats for later repairs.

Thin brick goes up with adhesive mortar or a panel system, so the 80 lb bag rate for full brick does not apply. Follow the thin brick maker's coverage figure for the setting mortar.

Veneer Cost per Square Foot and per 1,000 Bricks

At $650 per 1,000 modular bricks, the brick alone costs $4.46 per sq ft of wall. Add mortar at $9.50 a bag and $12 per sq ft of mason labor, and a 1,000 sq ft wall comes to about $18.84 per sq ft installed.

Price per 1,000 ModularBrick Cost, 1,000 sq ftMaterials per sq ftInstalled per sq ft, $12 Labor
$500$3,771.50$5.71$17.71
$650$4,902.95$6.84$18.84
$800$6,034.40$7.97$19.97
$1,000$7,543$9.48$21.48

These brick veneer calculator prices are samples, not market quotes, and they include 10% waste and 204 bags of mortar. Labor dominates, at $12 of the $18.84, so a mason's per-square-foot rate moves the total more than the brick price does.

Price per 1,000 bricks only compares fairly within one size in a brick veneer calculator budget. At the same $650, king brick costs $3.12 per sq ft of wall and modular $4.46, because a king brick covers 43% more face.

Convert each quote to a per-square-foot figure first, so a cheaper-looking price per thousand on a small brick does not hide a higher wall cost.

On the 260 sq ft example wall, a brick veneer calculator cost total runs $1,275.30 for 1,962 bricks, $513 for 54 bags and $3,120 for labor. That is $4,908.30 installed, or $18.88 per sq ft of net wall.

Double Wythe and 9 Inch Wall Brick Counts

A double wythe modular wall needs 13.71 bricks per sq ft, twice the veneer rate, plus a mortar-filled collar joint. A 9 in Indian wall of 230 × 110 × 70 mm bricks takes 9.68 bricks per sq ft of face.

That 9 in wall is two bricks thick, 110 + 10 + 110 = 230 mm, with a 10 mm joint. Its face rate of 9.68 per sq ft answers the common question of how many bricks go in 1 sq ft of a 9 inch wall.

WallThicknessBricks per sq ft of FaceBricks per cu ftBricks per m³
India Standard, 1 wythe110 mm4.8413.41473.6
India Standard, 2 wythes230 mm9.6812.82452.7
India Modular, 1 wythe90 mm4.6515.73555.5
India Modular, 2 wythes190 mm9.2914.9526.2
Modular US, 2 wythes7 5/8 in13.7121.58762.1

The collar joint between wythes adds mortar to a brick veneer calculator total. A double wythe modular wall gets about 28.9 bricks per 80 lb bag instead of 37, so 100 sq ft of wall takes 1,372 bricks and 48 bags before waste.

A brick veneer calculator India estimate follows the same face math with metric bricks. For a single wythe of India Standard brick, 52.08 bricks cover each m², and a two-brick 230 mm wall doubles that to 104.2 per m².

Measuring and Sizing Brick Walls

Measuring a wall and sizing a brick decide every count above. These answers use the same 3/8 in joint and the same brick veneer calculator example wall as the earlier tables.

What is a brick wall calculator?

A brick wall calculator is a materials estimate built from net wall area and the brick's face size with its joint. For a 260 sq ft modular wall, the result is 1,962 bricks, 54 bags and 110 ties.

The same math gives the brick size question its answer. A brick's square footage is its face plus one joint each way, divided by 144, so a modular brick covers 21 sq in, or 0.146 sq ft, and a king brick 30 sq in, or 0.208 sq ft.

How do you measure a brick wall?

Measure the length and height of each wall face in feet, multiply, then subtract every door and window. A 30 × 10 ft wall with a 3 × 7 ft door and a 4 × 4.75 ft window loses 40 sq ft, leaving 260 sq ft of brick.

Measure the height to the underside of the soffit or the top of the wall, not to the roof line, and count gable triangles as half of base times height. For an existing wall, counting courses and multiplying by 2 5/8 in gives modular height.

How to calculate bricks in 1 cft?

Divide the bricks per square foot of face by the wall thickness in feet. A 9 in Indian wall of 230 × 110 × 70 mm bricks holds 9.68 bricks per sq ft over 0.755 ft of thickness, or 12.82 bricks per cubic foot.

One cubic foot is 1 ft × 1 ft × 1 ft of wall, so 100 cft of 9 in brickwork needs 1,282 bricks before waste. A 110 mm half-brick wall packs more bricks per cubic foot, 13.41, because it has no collar joint taking up volume.