Mortar Calculator

Updated

Mortar Calculator turns a brick or block count, or a wall’s length and height, into bags of mortar mix, and lists the cement, lime and sand to mix Type N, S, M or O mortar on site.

Quick Setup

Enter a brick or block count, or switch to wall size to count them for you.

qty
ft
ft
ft²
Unit Size and Joint0.375 in joint

Bed width is the wall thickness for brick, and the two face shells for hollow block.

in
in
in
in
Bags and Waste80 lb bags

Units per bag fills in from the bag size and unit. Type your own to match a bag label.

lb
per bag
%
%
%
Mortar Needed
15 Bags of Mortar
500 bricks ÷ 37 per 80 lb bag × 1.10 = 14.86 bags
1,200 lb of Mortar Mix
Bags Before the Extra13.51
Mixing Water, About18.8 gal
Bags times bag weight gives the load to carry home. Water is scaled to your bag from the 5 quarts Quikrete adds to an 80 lb bag of mortar mix.
525 Bricks to Order
Wall Area They Cover74.1 ft²
Bricks per ft²6.75
The order adds your waste for cuts and breakage. Brick presets count by nominal size, with three modular courses to 8 inches, as BIA does.
4.84 ft³ Mortar to Site Mix
Joint Volume, No Waste4.03 ft³
Per 100 ft² of Wall5.44 ft³
Joint volume is the mortar that stays in the wall. The Brick Industry Association adds 15 to 25 percent to it for mortar lost on site.
0.81 Sacks of Cement
Hydrated Lime32.3 lb
Sand, Damp and Loose387 lb
Parts are cement, lime and sand by volume under ASTM C270. A cement sack is 94 lb, or one cubic foot, and metric bags here are 50 kg.
Mortar by Unit Count37 per bag
CountBags of 80 lbSite Mix Mortar
100 bricks30.97 ft³
500 bricks154.84 ft³
1,000 bricks309.68 ft³
5,000 bricks14948.38 ft³
Site Mix by Mortar TypeType N
MortarPartsCementLime
Type N1 : 1 : 60.81 sacks32.3 lb
Type S1 : 1/2 : 4 1/21.08 sacks21.5 lb
Type M1 : 1/4 : 3 3/41.29 sacks12.9 lb
Type O1 : 2 : 90.54 sacks43 lb
1 : 4 Mix1 : 0 : 41.21 sacksNone
1 : 6 Mix1 : 0 : 60.81 sacksNone
Where to MeasureUnit and joint
Unit LengthUnit Height ↕Joint Thickness (grey)Front ViewMortar Bed Width ↕Mortar BedTop View of a Course
Bag Count Follows the Bag Label
Units per bag start from Quikrete’s rating of up to 37 standard bricks or 13 standard blocks per 80 lb (36.3 kg) bag, then scale to your 80 lb bag, unit and joint. The joints themselves hold 4.03 ft³, so mixing your own by volume takes less material than the bag count suggests.

How the Mortar Calculator Counts Bags

The Mortar Calculator works from the yield printed on the bag. Quikrete rates an 80 lb bag of Mortar Mix at up to 37 standard bricks or 13 standard blocks. The rating is in its Mortar Mix data sheet and the block is the 8 × 8 × 16 in size. Your count is divided by that yield, the extra allowance is added, and the answer is rounded up to whole bags.

With the default 500 modular bricks, 500 ÷ 37 gives 13.51 bags. The 10 percent extra lifts that to 14.86, so the result is 15 bags of 80 lb mix. That load weighs 1,200 lb and needs about 18.8 gallons of water, based on the 5 quarts Quikrete adds to each 80 lb bag.

A different bag weight scales the yield in proportion. A 60 lb bag lays about 27.8 modular bricks or 9.8 blocks. If your bag lists its own figure, type it into Units Laid per Bag and the Mortar Calculator uses the label instead.

Mortar Bags for 100, 500 and 1,000 Bricks

These counts are for modular brick with a 3/8 in joint and include the 10 percent extra. Without the extra, 1,000 bricks need 27.03 bags of 80 lb mix, which rounds up to 28 whole bags.

Modular bricks60 lb bags80 lb bags
5022
10043
5002015
1,0004030
1,5006045

Larger bricks carry more mortar each, so a bag lays fewer of them. The mortar volumes below come from Table 4 of the Brick Industry Association's Technical Note 10. The bag yields are scaled from Quikrete's 37 bricks by the joint volume of each size.

Brick sizeBricks per 100 ft²Mortar per 1,000 bricksBricks per 80 lb bag
Modular6758.1 ft³37
Engineer Modular5638.5 ft³35.1
Closure Modular4509.1 ft³32.6
Norman45011.2 ft³26.6
Utility30012.3 ft³24.3

If you still need the brick count itself, the Brick Calculator works it out from the wall size. The Brick Industry Association suggests adding at least 5 percent to that count for breakage and cuts.

Bags of Mortar per 100 Blocks

The Mortar Calculator switches to a yield of 13 per 80 lb bag when you pick 8 in Concrete Block. At that rate 100 blocks need 7.69 bags before the extra. With 10 percent added, the order comes to 9 bags of 80 lb mix or 12 bags of 60 lb mix.

8 in blocks60 lb bags80 lb bags
5065
100129
2002317
3003426

Hollow block is normally laid with mortar on the two face shells only. For that reason the Concrete Masonry and Hardscapes Association says in TEK 04-02A that mortar estimates do not depend on block width. A 6 in, 8 in or 12 in block of the same face size takes about the same mortar.

The Concrete Block Calculator gives the block count for a wall, with 5 percent waste as the usual allowance. Filling the cores is a separate material, and the CMU Grout Calculator handles that volume.

Using the Mortar Calculator by Square Feet

Switch Calculate From to Wall Length and Height when you know the wall but not the count. Square feet is the wall length times its height. Enter doors and windows in Openings Area and that area is taken off before the count. Brick presets are counted by nominal size, so three modular courses make 8 in.

Modular brick runs 6.75 to the square foot in the Brick Industry Association table. Standard block runs 1.125 to the square foot, because each face covers 8/9 of a square foot. An 80 lb bag therefore covers about 5.5 ft² of modular brick wall or 11.6 ft² of block wall.

Take a wall 20 ft long and 8 ft high in modular brick. That is 160 ft² and 1,080 bricks. Dividing by 37 and adding 10 percent gives 32.1, so the order is 33 bags of 80 lb mix weighing 2,640 lb.

Add a 3 ft by 7 ft door and the opening is 21 ft². The wall drops to 139 ft² and 939 bricks. The same math gives 27.9, so the order falls to 28 bags and the load to 2,240 lb.

In metric, a square meter holds about 73 modular bricks or 12 standard blocks. That works out to roughly 2 bags of 80 lb mix per square meter of brick and just under 1 bag per square meter of block. A wall of 1,000 ft² needs 6,750 modular bricks and 201 bags, or 1,125 blocks and 96 bags.

Cement Mortar Calculator for Site Mixing

Mixing your own mortar starts from the volume of the joints, not from a bag label. The Mortar Calculator finds the mortar around one unit from its length, height, bed width and joint thickness.

For a modular brick with a 3/8 in joint, that is 3.625 × (8 × 2.625 - 7.625 × 2.25), or 13.93 cubic inches. Over 1,000 bricks it comes to 8.06 ft³, which matches the 8.1 ft³ in the Brick Industry Association table. The same source adds 15 to 25 percent for mortar lost on site, and the tool starts at 20 percent.

The mortar volume is then split by the ASTM C270 proportions for the type you pick. Sand is measured damp and loose, and one cubic foot of it yields about one cubic foot of mortar. Cement volume is the mortar volume divided by the sand parts.

A 94 lb sack of portland cement is one cubic foot. Hydrated lime is taken at 40 lb per cubic foot and sand at 80 lb per cubic foot. The table shows the result for 1,000 modular bricks, which is 9.68 ft³ of mortar and 774 lb of sand for every type.

Mortar typeCement : lime : sandMinimum strengthCementHydrated lime
Type N1 : 1 : 6750 psi1.61 sacks64.5 lb
Type S1 : 1/2 : 4 1/21,800 psi2.15 sacks43 lb
Type M1 : 1/4 : 3 3/42,500 psi2.58 sacks25.8 lb
Type O1 : 2 : 9350 psi1.08 sacks86 lb
1 : 4 Mix1 : 0 : 4Not an ASTM type2.42 sacksNone
1 : 6 Mix1 : 0 : 6Not an ASTM type1.61 sacksNone

The 1 : 4 and 1 : 6 choices are plain cement and sand mixes with no lime. A 1 : 6 mix for 1,000 modular bricks takes 1.61 sacks of cement, which is about 151 lb, with the same 774 lb of sand. A 1 : 4 mix takes 2.42 sacks. Neither ratio is an ASTM C270 mortar type, so check what your plans or local code call for.

Many cement and sand guides multiply the wet volume by 1.33 to get a dry volume. That factor is not used here. ASTM C270 already measures the sand loose, so the sand volume stands in for the finished mortar volume.

The site mix total looks small beside the bag count, and the gap is real. Joint volume is a theoretical figure for mortar that stays in the wall. The Brick Industry Association also quotes the masons' rule of eight bags of masonry cement per 1,000 modular bricks, with waste built in. At one ton of sand per eight bags, that rule is about 2,560 lb of dry material, close to the 2,400 lb in 30 bags of 80 lb mix.

For block, the same TEK gives a field rule. One 94 lb sack of portland cement, about half a 50 lb bag of hydrated lime and 4 1/4 ft³ of sand lay roughly 62 hollow blocks. That is about 1.6 sacks of cement, 40 lb of lime and 6.9 ft³ of sand per 100 blocks. With masonry cement, one 70 lb bag lays about 30 blocks and a ton of sand covers about 240.

The Mortar Calculator applies that sand rule to block, then adds your site waste. For 100 blocks it shows 6.85 ft³ of mortar before waste and about 8.2 ft³ with the default 20 percent. In Type S that is 1.83 sacks of cement, 36.6 lb of hydrated lime and 658 lb of sand.

The Cement Calculator and the Concrete Mix Calculator cover mixes with gravel. Reinforced concrete, often searched as RCC, belongs with those tools because mortar has no coarse aggregate.

Choosing Type N, S, M or O

Quikrete's standard Mortar Mix is a Type N mortar under ASTM C270, so the bag count assumes Type N unless you buy another type. The mortar type changes the site mix recipe but not the joint volume.

The association's TEK 09-01A notes that building codes usually call for Type M, S or N. Foundation walls built by empirical design need Type M or S. Glass block needs Type N or S, and the higher seismic design categories need Type S or M. A below-grade job such as the base of a retaining wall is where the stronger types usually apply.

Joint Thickness and Bed Width

A 3/8 in joint is the standard for brick and block, and both Quikrete's yields and the Mortar Calculator default assume it. A thicker joint raises mortar use quickly. For modular brick the Brick Industry Association table goes from 8.1 ft³ per 1,000 bricks at 3/8 in to 10.3 ft³ at 1/2 in.

Mortar Bed Width is the depth of mortar across the wall. For brick it is the full brick width of 3 5/8 in. For hollow block it is the two face shells, which the tool sets at 2.5 in. The Brick Course Height Calculator shows how the joint sets the coursing, since three modular courses make 8 in.

Mortar Calculator for Slab and Tile Work

Searches for a mortar calculator for slab usually mean one of three jobs. Thinset under floor tile is sized by trowel notch, and the Tile Mortar Calculator handles it. A dry-pack mud bed under tile is covered by the Deck Mud Calculator. A poured slab is concrete, so its volume belongs in the Concrete Calculator.

The Mortar Calculator on this page covers joints between bricks and blocks only. Stucco, plaster and parging are spread by area and thickness, so their quantities are not part of these results.

Quick Answers on Mortar Quantities

The answers below use the same Quikrete yields and Brick Industry Association volumes as the tool. Each one assumes modular brick or standard 8 in block with a 3/8 in joint.

How many bags of cement do I need for 500 bricks?

By joint volume, 500 modular bricks need 4.84 ft³ of site-mixed mortar with 20 percent waste. In Type N that is 0.81 sacks of portland cement, 32.3 lb of hydrated lime and 387 lb of sand. The masons' field rule is more generous at about four bags of masonry cement for 500 bricks. Buying one full sack of portland cement leaves little margin, so two is the safer order.

How much cement do I need for 1 square meter of brickwork?

One square meter of modular brick wall holds about 73 bricks and 0.59 ft³ of mortar in the joints. With 20 percent waste the mix is 0.71 ft³. In Type N that takes about 11 lb (5 kg) of portland cement, 4.7 lb of hydrated lime and 57 lb (26 kg) of sand. For 100 ft² the same math gives 1.1 sacks of cement and 528 lb of sand.

How much sand goes with one bag of cement?

It depends on the mortar type. One 94 lb sack of portland cement takes 6 ft³ of sand in Type N and 4 1/2 ft³ in Type S. Type M takes 3 3/4 ft³ and Type O takes 9 ft³. ASTM C270 sets the sand at 2 1/4 to 3 times the combined volume of cement and lime. With masonry cement, the block industry rule is one ton of sand for every eight bags.

How much water does a bag of mortar need?

Quikrete calls for about 5 quarts of water per 80 lb bag and 3 3/4 quarts per 60 lb bag. The stated maximum is just under 6 quarts and 4 1/2 quarts. Add the last of it slowly. The mix is right when a 1/2 in layer stays on a trowel held nearly vertical.

What does the mortar for a wall cost?

Multiply the bag count by the shelf price at your store. The 20 ft by 8 ft brick wall above needs 33 bags of 80 lb mix. Site mixing the same wall takes about 1.8 sacks of portland cement, 70 lb of hydrated lime and 850 lb of sand by joint volume. Price those three materials the same way and compare the two totals before you choose a route.

Is this the mortar calculator for Squad, Arma or PUBG?

No, those are artillery tools. Players use them to turn a target distance into an elevation setting for an in-game mortar. The Mortar Calculator here is for masonry, so its inputs are bricks, blocks, joints and bags of mix.