Capacitors in Parallel Calculator

Updated

Capacitors in parallel calculator for 2 to 10 parts in mixed units, with the total, charge and energy at a voltage, voltage rating, ripple, hold-up time, bank ESR and parts needed.

Capacitors in Parallel

Enter each capacitor in the parallel bank. Units can differ; the total is the plain sum of all of them.

V
Voltage, Rating, ESR & Load--
V
V
V
V
37.25 mF Total in Parallel
30 + 0.5 + 6 + 0.75 = 37.25 mF
447 mC Total Charge at 12 V
Stored Energy2.682 J
Charge on C₁, the Most360 mC
Every branch sees the same voltage, so each holds Q = C × V and the charges add.
75% of the Voltage Rating
Headroom Left4 V
Energy at Full Rating4.768 J
All parts get the full bank voltage, so the lowest-rated one sets the limit.
18.63 ms Hold-Up at 2 A
Full-Wave Ripple, 60 Hz Mains447.4 mV
Voltage Drop Rate53.69 V/s
Time to sag by the allowed drop at a steady load, t = C × ΔV ÷ I, and filter ripple.
71.21 mΩ Reactance at 60 Hz
If 12 V Were AC RMS168.5 A
C₁ Alone88.42 mΩ
AC opposition of the whole bank, XC = 1 ÷ 2πfC, lower than any single part.
Parallel Bank Diagram4 branches at 12 V
12VC₁30 mF360 mCC₂500 µF6 mCC₃6 mF72 mCC₄750 µF9 mC
Charge, Energy & Current per Capacitor4 capacitors
CapacitorCapacitanceShareChargeEnergyReactanceCurrent if AC
C₁ (most charge)30 mF80.5%360 mC2.16 J88.42 mΩ135.7 A
C₂500 µF1.34%6 mC36 mJ5.305 Ω2.262 A
C₃6 mF16.1%72 mC432 mJ442.1 mΩ27.14 A
C₄750 µF2.01%9 mC54 mJ3.537 Ω3.393 A
Bank total37.25 mF100%447 mC2.682 J71.21 mΩ168.5 A
Total in Every Capacitance Unit1 F = 1,000,000 µF
UnitBank TotalOne Unit Equals
Picofarads (pF)37,250,000,0000.000001 µF
Nanofarads (nF)37,250,0000.001 µF
Microfarads (µF)37,2501 µF
Millifarads (mF)37.251,000 µF
Farads (F)0.037251,000,000 µF
Step-by-Step Math8 steps
1. Same UnitC₁ = 30 mF, C₂ = 0.5 mF, C₃ = 6 mF, C₄ = 0.75 mF
2. Add ThemCₜ = 30 + 0.5 + 6 + 0.75 = 37.25 mF
3. Total ChargeQ = 37.25 mF × 12 V = 447 mC
4. Stored EnergyE = 0.5 × 37.25 mF × (12 V)² = 2.682 J
5. Hold-Up Timet = 37.25 mF × 1 V ÷ 2 A = 18.63 ms
6. Full-Wave RippleVpp = 2 A ÷ (2 × 60 Hz × 37.25 mF) = 447.4 mV
7. ReactanceXC = 1 ÷ (2π × 60 Hz × 37.25 mF) = 71.21 mΩ
8. Result37.25 mF Total in Parallel
Parallel Capacitors Simply Add
Every capacitor sees the same voltage, so the charges add and the total is the sum: 37.25 mF, more than the largest part alone.

Capacitors in Parallel Calculator Totals Across pF, nF and mF

Capacitors in parallel add directly: 30 mF, 500 µF, 6 mF and 750 µF make 37.25 mF. Each branch sits across the same two rails, so the bank behaves like one capacitor with all the plate area combined.

CT is the total parallel capacitance and C1 to Cn are the individual parts. Every value must be in the same unit first, so 500 µF becomes 0.5 mF before it joins 30 mF in any capacitors in parallel calculator sum.

Capacitors in parallelTotalTotal ÷ largest part
47 pF + 22 pF69 pF1.468×
100 nF + 100 nF + 100 nF300 nF3×
1 µF + 100 nF1.1 µF1.1×
10 µF + 10 µF20 µF2×
10 µF + 22 µF + 47 µF79 µF1.681×
100 µF + 220 µF320 µF1.455×
100 µF + 100 nF + 10 nF100.1 µF1.001×
30 mF + 500 µF + 6 mF + 750 µF37.25 mF1.242×

A capacitors in parallel calculator total is always above the largest part, but small parts barely move it. The 100 nF and 10 nF in the decoupling row add only 0.11 µF to 100 µF, a 0.1% change.

Unit slips are the common capacitors in parallel calculator error. Treating 500 µF as 500 mF in the 37.25 mF example would give 536.75 mF, so each value should be converted before adding, the same way the formula works on paper.

Tolerance carries straight through. The 79 µF bank of ±20% electrolytics can measure anywhere from 63.2 µF to 94.8 µF when every part sits at the same limit, whatever the capacitors in parallel calculator nominal says.

Charge and Energy on a Shared Voltage

Every capacitor in a parallel bank sees the full bank voltage, so the largest part holds the most charge. At 12 V the 30 mF part in the 37.25 mF bank stores 360 mC of the 447 mC total and 2.16 J of the 2.682 J.

Q is the total charge in coulombs, E is the stored energy in joules, CT is the bank capacitance in farads and V is the voltage across the bank. Each branch follows the same rule with its own capacitance.

Part at 12 VShare of bankChargeEnergy
30 mF80.5%360 mC2.16 J
6 mF16.1%72 mC432 mJ
750 µF2.01%9 mC54 mJ
500 µF1.34%6 mC36 mJ
Bank total100%447 mC2.682 J

The voltage does not split, which is the key difference from series wiring, and the branch charges sum to Q in any capacitors in parallel calculator table. A capacitors in parallel voltage check is therefore one number, the supply.

Energy in a capacitors in parallel calculator result rises with the square of voltage, so headroom matters. The same 37.25 mF bank run at its 16 V rating would hold 4.768 J, 78% more than at 12 V, from only a third more voltage.

Rating Limit Set by the Weakest Part

A parallel bank is rated at its lowest-rated part, not at the sum. Parts rated 16 V, 25 V and 35 V together make a 16 V bank, and 12 V across it uses 75% of that rating with 4 V of headroom in a capacitors in parallel calculator check.

Paralleling raises capacitance and current handling but never voltage. To share a higher voltage, parts go in series instead, which the Capacitors in Series Calculator covers along with balancing resistors.

A parallel capacitor calculator voltage check should use the highest voltage the bank will ever see, including switch-on peaks. A 12 V AC transformer peaks near 17 V before diode drops, which already exceeds a 16 V part.

Polarity applies to every branch, which no capacitors in parallel calculator total reveals. With electrolytics, each positive lead must go to the positive rail, and one part fitted backwards is reverse biased across the full bank voltage.

Hold-Up Time and Ripple Under Load

A 37.25 mF bank feeding 2 A sags by 1 V in 18.63 ms, falling at 53.69 V/s. Hold-up time and rectifier ripple both come from the same charge balance, so they scale directly with the capacitors in parallel calculator total.

t is the hold-up time in seconds, ΔV is the allowed drop in volts, I is the load current in amps, f is the mains frequency in hertz and Vpp is the peak-to-peak ripple behind a full-wave rectifier.

Bank at 1 A loadFull-wave ripple, 50 HzFull-wave ripple, 60 HzHalf-wave ripple, 50 HzHold-up for 1 V drop
1 mF10 V8.333 V20 V1 ms
2.2 mF4.545 V3.788 V9.091 V2.2 ms
4.7 mF2.128 V1.773 V4.255 V4.7 ms
10 mF1 V833.3 mV2 V10 ms
22 mF454.5 mV378.8 mV909.1 mV22 ms

For a capacitors in parallel calculator ripple figure, the 50 Hz column is the one to use across Europe, Asia and Africa. The same bank gives 20% more ripple there than on 60 Hz mains, so a design checked only at 60 Hz can fall short abroad.

Load current also sets the bank size in reverse. For 1 V of full-wave ripple at 1 A on 50 Hz, the bank needs 10 mF, which two 4.7 mF parts nearly reach at 9.4 mF.

The 37.25 mF bank at 2 A gives 536.9 mV of full-wave ripple on 50 Hz and 447.4 mV on 60 Hz. Both formulas assume a steady load and ignore ESR, which adds its own ripple on top.

Counting Identical Parts for a Charge or Energy Target

Storing 1 C at 110 V takes 9,091 capacitors of 1 µF in parallel. Each holds only 110 µC at that voltage, and 1 ÷ 0.000110 is 9,090.91, which rounds up to whole parts in any capacitors in parallel calculator count.

N is the number of parts, Q is the target charge, Ce is the capacitance of one part and V is the bank voltage. For an energy target, the divisor becomes ½CeV², and for a capacitance target it is Ce alone.

Each partTargetPer partParts neededBank
1 µF4.7 µF1 µF55 µF
2.2 mF10 mF2.2 mF511 mF
1 µF at 110 V1 C110 µC9,0919.091 mF
1 µF at 110 V5 J6.05 mJ827827 µF, 5.003 J
470 µF at 400 V0.5 C188 mC31.41 mF, 564 mC
100 µF at 50 V10 J125 mJ808 mF
1 µF1 F1 µF1,000,0001 F

Large capacitors in parallel calculator counts point to a different part, not a bigger board. The 9,091-part bank acts like one 9.091 mF capacitor, so a single 10 mF part rated above 110 V does the same job.

Voltage is the cheaper lever for energy. Doubling the voltage on the same parts quadruples the energy, while doubling the count only doubles it, so a capacitors in parallel calculator energy target is best met with the highest safe voltage first.

Topping Up a Bank to a Target Value

Raising 30 mF and 500 µF in parallel to 40 mF takes one extra 9.5 mF part. The missing value is just the target minus the sum already fitted, and it only works upward, since parallel can never lower a capacitors in parallel calculator total.

Already fittedTargetExact partNearest E12 sizes and totals
10 µF15 µF5 µF4.7 µF gives 14.7 µF, 5.6 µF gives 15.6 µF
100 nF150 nF50 nF47 nF gives 147 nF, 56 nF gives 156 nF
470 µF + 470 µF1 mF60 µF56 µF gives 996 µF, 68 µF gives 1.008 mF
30 mF + 500 µF40 mF9.5 mF8.2 mF gives 38.7 mF, 10 mF gives 40.5 mF

Adding capacitors in parallel is the standard way to hit an odd value from stock parts. A 4.7 µF beside a 10 µF lands within 2% of 15 µF, well inside the ±10% or ±20% tolerance of most electrolytics.

A target below the fitted total needs series wiring instead of a capacitors in parallel calculator top-up. Bringing a 10 µF part down to 4.7 µF takes 8.868 µF in series, the reverse of every row above.

ESR, Reactance and Mixed Ceramic Banks

Four identical capacitors of 100 mΩ ESR in parallel give 25 mΩ, so a 2 A load loses 100 mW in the bank instead of 400 mW in one part. Equal ESRs divide by the count, the same way equal resistors in parallel do.

For a capacitors in parallel calculator ESR figure, that division only holds for identical parts. Mixed parts follow the parallel-resistor rule, where the lowest ESR dominates.

Identical partsESR eachBank ESRLoadESR lossESR ripple
250 mΩ25 mΩ3 A225 mW75 mV
4100 mΩ25 mΩ2 A100 mW50 mV
1020 mΩ2 mΩ5 A50 mW10 mV

Reactance falls as capacitance rises, so a bank always has less of it than any single part. The 79 µF bank of 10 µF, 22 µF and 47 µF presents 40.29 Ω at 50 Hz, 33.58 Ω at 60 Hz and 2.015 Ω at 1 kHz.

XC is the reactance in ohms, f is the frequency in hertz and CT is the bank total in farads. At 100 kHz the same 79 µF bank is down to 20.15 mΩ, where ESR usually matters more.

Mixed banks trade on ESR. In TI's test at 12 V and 8 A, four MLCCs in parallel gave 0.57 mΩ total ESR, while two MLCCs plus one aluminum polymer part gave 1.08 mΩ.

Parts with different self-resonant frequencies can also fight. TDK's MLCC guide warns that parallel parts form an LC circuit whose anti-resonance creates an impedance peak.

A capacitors in parallel calculator total says nothing about that peak, so a mixed bank needs each part's impedance curve, not just its capacitance, when noise at one frequency matters.

Bench Answers on Parallel Capacitors

Most parallel bank questions come back to one fact: every branch carries the same voltage. The answers below start from that and put numbers on each common case, from two parts to thousands.

How to calculate capacitors in parallel?

Convert every value to one unit, then add them. A 10 µF, 22 µF and 47 µF set gives 79 µF, and mixed units such as 1 µF plus 100 nF become 1 µF + 0.1 µF = 1.1 µF.

Microfarads in parallel add the same way as any other unit. In a spreadsheet, values in one unit in A2 to A5 total with =SUM(A2:A5), the same total a capacitors in parallel calculator with steps reaches.

How to connect 3 capacitors in parallel?

Join one lead of each capacitor to the first rail and the other lead of each to the second rail. Three 100 nF parts wired this way make 300 nF, and each one sees the full supply voltage.

With electrolytics, all three positive leads go to the positive rail. Short, equal leads keep the parts sharing current evenly, which matters most in high-current or high-frequency banks.

What is the formula for capacitors in parallel?

The formula is CT = C1 + C2 + … + Cn, the plain sum of all parts. It comes from Q = CV: the charges add while the voltage stays the same, so the capacitances add too.

The equivalent capacitance of a parallel combination is therefore always larger than its largest part. The capacitors in series and parallel formula pair is the mirror of resistors, where parallel resistances add as reciprocals.

What happens if two capacitors are connected in parallel?

The capacitances add and the voltage rating becomes the lower of the two. Two 10 µF capacitors in parallel make a net 20 µF, and a 100 µF part beside a 220 µF part makes 320 µF.

Connecting two charged capacitors at different voltages makes them share charge at once. The pulse current can be large, so discharge both or bring them to the same voltage before joining them.

How many 1 microfarad capacitors must be connected in parallel to store a charge of one coulomb with a potential of 110 volt across the capacitors?

The answer is 9,091 capacitors. Each 1 µF part holds 1 µF × 110 V = 110 µC, and 1 C ÷ 110 µC is 9,090.91, which rounds up to the next whole part and gives a 9.091 mF bank.

The same capacitors in parallel calculator count for an energy target is much smaller. Storing 5 J at 110 V needs 827 parts of 1 µF, since each holds 6.05 mJ, giving 5.003 J in total.

Why do parallel capacitors increase total capacitance?

Parallel wiring adds plate area while keeping the same gap and voltage. Each branch stores its own charge at the shared voltage, so two 10 µF parts hold twice the charge of one at any voltage, which is what 20 µF means.

Designers use this to reach values or currents one part cannot, then confirm the bank with a capacitors in parallel calculator check. A bank of four 100 mΩ electrolytics also cuts ESR to 25 mΩ and spreads ripple current across four cans.

How to calculate resistor and capacitor in parallel?

A resistor and capacitor in parallel combine as impedances, not as a sum. At 1 kHz, 1 kΩ in parallel with 1 µF (159.2 Ω of reactance) gives 157.2 Ω at a phase angle of -80.96°.

Z is the combined impedance, R is the resistance and XC is the capacitor's reactance at that frequency. The Capacitor Impedance Calculator gives XC for the capacitor side.

How to tell if two capacitors are in series or parallel?

Two capacitors are in parallel when both their leads meet at the same two nodes. They are in series when they share only one node and nothing else connects there, so the same current must flow through both.

Series and parallel networks are solved from the inside out. For 10 µF in parallel with 22 µF, then in series with 47 µF, first add to 32 µF, then combine 32 µF and 47 µF in series to get 19.04 µF.

How to calculate 3 capacitors in series?

Add the reciprocals and invert the result. For 10 µF, 22 µF and 47 µF, 1/10 + 1/22 + 1/47 = 0.1667 per µF, so the series total is 5.998 µF, against 79 µF for the same parts in parallel.

That 13.17× gap between a series result and a capacitors in parallel calculator result is typical. Three equal parts give exactly 9×, since series divides one value by three while parallel multiplies it by three.

How many µF is 1 farad?

One farad is 1,000,000 µF, and one microfarad equals 1,000 nF or 1,000,000 pF. The 37.25 mF bank above is therefore 37,250 µF, or 0.03725 F, in any capacitors in parallel calculator unit.

A capacitor marked 20 µF holds 20 microcoulombs per volt. Small ceramics print a code instead of the value, such as 104 for 100 nF, which the Capacitor Code Calculator decodes.

Can I use a 15 microfarad capacitor instead of 10?

Not as a like-for-like swap. A 10 µF part at ±20% may measure 8 µF to 12 µF, so 15 µF is 50% above nominal and outside its tolerance band, which can upset timing, filter or motor-run circuits.

In a supply reservoir, a larger capacitors in parallel calculator total usually only lowers ripple and lengthens hold-up, as long as the voltage rating and size match. Two parts in parallel, 10 µF plus 4.7 µF, also reach 14.7 µF.

How do I calculate the capacitance of a parallel plate capacitor?

Use C = ε0εrA ÷ d, with ε0 = 8.854 × 10-12 F/m. Two 100 cm² plates 1 mm apart in air give 88.54 pF, and closing the gap to 0.1 mm raises it to 885.4 pF.

Capacitance rises with plate area and dielectric constant and falls with the gap. For plate sizing, the Capacitance Calculator is the related tool, since a bank of finished parts never needs plate dimensions.

Does paralleling capacitors reduce or increase the voltage rating?

Paralleling does neither: the bank keeps the rating of its lowest-rated part. A 16 V part beside a 25 V part makes a 16 V bank, because both carry the same voltage, so a capacitors in parallel calculator voltage check uses 16 V.

Only series wiring raises the working voltage, and only with equal parts and balancing resistors. Paralleling raises capacitance, ripple current capacity and stored energy instead.

How do I calculate the total ESR and ESL for parallel capacitors?

For identical parts, divide one part's ESR and ESL by the count, so four parts of 100 mΩ give 25 mΩ. For unequal parts, combine the ESRs as parallel resistances, the same reciprocal sum used in the Parallel Resistor Calculator.

The simple division assumes equal board traces to every part. Long or uneven traces add their own inductance, so the bank ESL is usually higher than the datasheet value divided by n.

Can I parallel electrolytic and ceramic capacitors safely?

Paralleling them is normal practice, as long as each is rated for the bank voltage and the electrolytic's polarity is right. A 100 nF ceramic beside 100 µF adds 0.1% capacitance but keeps working at frequencies where the electrolytic does not.

The risks are anti-resonance between parts and loop stability in a regulator, since a low-ESR ceramic changes the output filter. Class 2 ceramics also lose capacitance under DC bias, per TDK, so their marked value overstates what they add.

What happens if one capacitor in a parallel bank fails short circuit?

A shorted part shorts the whole bank, since every branch shares the same two rails. All the stored energy, 2.682 J in the 37.25 mF bank at 12 V, can discharge through the fault at once.

Large banks often fuse each branch or use parts with safety vents for this reason. A failed-open part, by contrast, only removes its own capacitance and leaves the rest working.