Capacitors in Series Calculator

Updated

Capacitors in series calculator for 2 to 10 parts in mixed units, with the total, voltage and charge on each, safe stack voltage, balancing resistors and the part any target needs.

Capacitors in Series

Enter each capacitor in the chain. Units can differ; the total is always smaller than the smallest one.

Voltage, Rating & Frequency100 V · 63 V rated · 60 Hz
V
V
5.998 µF Total in Series
1/Cₜ = 1/10 + 1/22 + 1/47 (µF)
59.98 V on C₁, the Most
On C₃, the Least12.76 V
C₁ Share of Supply60%
Voltage divides inversely with capacitance, so the smallest capacitor takes the most.
599.8 µC Charge on Each
Total Energy Stored29.99 mJ
Energy in C₁17.99 mJ
Every capacitor in series holds the same charge, Q = C × V of the chain.
105 V Safe Chain Voltage
Max With Equal Resistors189 V
Balancing Resistor, Est.10.07 MΩ
Highest supply before the smallest capacitor passes its rating, without and with resistors.
442.3 Ω Reactance at 60 Hz
AC Current at 100 V226.1 mA
C₁ Alone265.3 Ω
AC opposition of the whole chain, XC = 1 ÷ 2πfC, which is higher than any single capacitor.
Series Chain Diagram100 V across 3
C₁10 µF59.98VC₂22 µF27.26VC₃47 µF12.76V
Voltage, Charge & Energy per Capacitor3 capacitors
CapacitorCapacitanceShareVoltageEnergyReactance
C₁ (most voltage)10 µF60%59.98 V17.99 mJ265.3 Ω
C₂22 µF27.3%27.26 V8.175 mJ120.6 Ω
C₃47 µF12.8%12.76 V3.827 mJ56.44 Ω
Chain total5.998 µF100%100 V29.99 mJ442.3 Ω
Balancing Resistors for DC Stacks10.07 MΩ each
ItemValueHow
Resistor across each cap10.07 MΩ670 Ω·F × (3 × 63 - 100) ÷ (2 × 47 µF × 63)
Resistor power rating0.788 mW or more2 × 63² ÷ R
Estimated leakage per cap2.35 µA1.5 mHz × C × 33.33 V
Voltage per cap when balanced33.33 V100 V ÷ 3
Balancing time constant7.89 minR × C = 10.07 MΩ × 47 µF
Settled within 1% after36.3 min4.6 × R × C

Leakage-based sizing for equal aluminum electrolytics from the same lot. Use ±1% resistors; with unequal capacitors this uses the largest one as an estimate.

Step-by-Step Math8 steps
1. Same UnitC₁ = 10 µF, C₂ = 22 µF, C₃ = 47 µF
2. Add the Reciprocals1/Cₜ = 1/10 + 1/22 + 1/47 = 0.166731 per µF
3. InvertCₜ = 1 ÷ 0.166731 = 5.99768 µF
4. Charge on EachQ = 5.998 µF × 100 V = 599.8 µC
5. Voltage on C₁V = Q ÷ C = 599.8 µC ÷ 10 µF = 59.98 V
6. Safe Supply63 V × 10 µF ÷ 5.998 µF = 105 V
7. ReactanceXC = 1 ÷ (2π × 60 Hz × 5.998 µF) = 442.3 Ω
8. Result5.998 µF Total in Series
DC Stacks Need Balancing Resistors
Leakage differs between parts, so fit about 10.07 MΩ (0.788 mW or more, ±1%) across each capacitor. The balancing table below shows the working.

Capacitors in Series Calculator Math for Two, Three and Ten Parts

A 10 µF and a 22 µF capacitor in series give 6.875 µF, less than the smaller part. Series capacitors share one charge, so their reciprocals add and the total always lands below the smallest value in the string.

CT is the total series capacitance and C1 to Cn are the individual capacitors, all in the same unit. The HyperPhysics series capacitor page derives it from the equal charge on each part.

For exactly two capacitors the same rule collapses to product over sum, the shortcut most people use for a 2 series capacitor check by hand.

C1 and C2 are the two capacitors. With 10 µF and 22 µF the result is 220 ÷ 32 = 6.875 µF, matching the reciprocal sum, so a two-part capacitors in series calculator check works with either formula.

Capacitors in seriesTotalTotal as % of smallest
10 µF + 10 µF5 µF50%
10 µF + 22 µF6.875 µF68.8%
2.2 µF + 4.7 µF1.499 µF68.1%
100 nF + 220 nF68.75 nF68.8%
1 µF + 100 nF90.91 nF90.9%
10 µF + 10 µF + 10 µF3.333 µF33.3%
10 µF + 22 µF + 47 µF5.998 µF60%
2 mF + 5 µF + 6 µF + 200 nF186.3 nF93.2%
10 × 100 µF10 µF10%

Equal parts divide cleanly: n identical capacitors in series give C ÷ n, so three 10 µF parts make 3.333 µF and ten 100 µF parts make 10 µF. Any capacitors in series calculator result for equal values should match that check.

A small part dominates. With 1 µF and 100 nF in series the total is 90.91 nF, 90.9% of the 100 nF alone, so adding a much larger capacitor in series barely changes anything.

Units can be mixed as long as each is converted first. The 2 mF, 5 µF, 6 µF and 200 nF string adds to 186.3 nF, and a slip of one prefix there changes the capacitors in series calculator total by a factor of 1,000.

Voltage on Each Capacitor in a Series String

The smallest capacitor takes the largest voltage. With 100 V across 10 µF, 22 µF and 47 µF in series, the 10 µF part carries 59.98 V, the 22 µF part 27.26 V and the 47 µF part only 12.76 V.

Vk is the voltage on capacitor k, V is the voltage across the whole chain, CT is the series total and Ck is that capacitor. Each share is CT ÷ Ck, and the shares in a capacitors in series calculator split add to 100%.

String and supplyTotalVoltage on each
10 µF + 22 µF + 47 µF at 100 V5.998 µF59.98 V, 27.26 V, 12.76 V
100 nF + 220 nF at 12 V68.75 nF8.25 V, 3.75 V
1 µF + 100 nF at 50 V90.91 nF4.545 V, 45.45 V
10 µF + 10 µF at 400 V5 µF200 V, 200 V

The split follows from the shared charge. In the 100 V example every part holds 599.8 µC, and V = Q ÷ C gives each voltage, which is why a capacitors in series voltage figure always falls as capacitance rises.

Energy in a capacitors in series calculator breakdown splits the same lopsided way. Of the 29.99 mJ stored in that string, the 10 µF part holds 17.99 mJ, the 22 µF part 8.175 mJ and the 47 µF part just 3.827 mJ.

The 1 µF and 100 nF pair shows the trap in a capacitive divider. The small part takes 45.45 V of 50 V, so a 16 V or 25 V rating chosen from the large part's voltage would fail at once.

A resistor divider splits voltage in proportion to resistance, the opposite way round, which the Voltage Divider Calculator covers for DC circuits.

Rating a Series Stack: Safe Voltage and Balancing Resistors

Series capacitors only share their voltage ratings when they are equal and balanced. Three capacitors rated 63 V can hold 189 V when balanced, but 10 µF, 22 µF and 47 µF parts are safe only to 105 V, since the 10 µF part reaches 63 V first.

Vsafe is the highest chain voltage before the smallest part hits its rating, VR is the voltage rating of each part, Cmin is the smallest capacitor and CT is the capacitors in series calculator total for the string.

Equal capacitors still drift apart on DC because leakage differs from part to part, which no capacitors in series calculator ratio can show.

The Cornell Dubilier aluminum electrolytic application guide sizes one resistor across each capacitor to hold the split, using its Eq. 3.

R is each balancing resistor in ohms, n is the number of capacitors, VM is the highest voltage allowed on any one part, Vb is the bus voltage, Cs is each capacitance in farads and 670 has units of Ω·F.

Stack and busRating eachResistor eachResistor power, minTime constant R × CWithin 1% after
2 × 220 µF at 100 V100 V3.045 MΩ6.57 mW11.2 min51.4 min
2 × 1,000 µF at 50 V35 V382.9 kΩ6.4 mW6.38 min29.4 min
2 × 470 µF at 400 V250 V570.2 kΩ219 mW4.47 min20.5 min
3 × 470 µF at 600 V250 V427.7 kΩ292 mW3.35 min15.4 min
4 × 2,200 µF at 800 V250 V81.21 kΩ1.54 W2.98 min13.7 min

CDE sets the resistor power at 2VM² ÷ R or more, with resistors matched within ±1%. Any voltage imbalance then decays with a time constant of R × C, so the split is within 1% after 4.6 × R × C.

The formula assumes equal capacitors from the same lot at the same temperature. With unequal parts, sizing from the largest capacitor gives only a capacitors in series calculator estimate, and switch-on surges still split by capacitance.

A bus at or above n × VM has no answer. Two 350 V parts on a 700 V bus leave zero margin, so the right capacitors in series calculator fix there is a third capacitor or higher-rated parts, not a resistor value.

Finding the Missing Capacitor for a Target Total

To bring 10 µF down to 4.7 µF, a capacitor of 8.868 µF has to go in series. Adding capacitors in series only ever lowers a total, so the target must sit below what the known parts already give.

Cx is the missing capacitor, CT is the target total and Ck is the series total of the parts already in the string. A target close to Ck needs a very large Cx, the warning sign in any capacitors in series calculator run.

Known partsTargetExact part neededNearest E12 sizes and totals
10 µF4.7 µF8.868 µF8.2 µF gives 4.505 µF, 10 µF gives 5 µF
100 nF68 nF212.5 nF180 nF gives 64.29 nF, 220 nF gives 68.75 nF
22 µF + 47 µF10 µF30.06 µF27 µF gives 9.637 µF, 33 µF gives 10.31 µF
10 µF9.9 µF990 µF820 µF gives 9.88 µF, 1 mF gives 9.901 µF

The last row shows why a near target is a poor plan. Trimming 10 µF to 9.9 µF needs 990 µF in series, a large part for a 1% change that sits well inside the ±10% or ±20% tolerance of most capacitors anyway.

A capacitors in series calculator answer rarely lands on a stock value. For 68 nF from a 100 nF part, a 220 nF capacitor gives 68.75 nF, 1.1% high, which suits most timing and filter work better than the 64.29 nF from 180 nF.

Parallel Versus Series With the Same Parts

Capacitors in parallel simply add, so 10 µF and 22 µF side by side make 32 µF against 6.875 µF in series. The capacitor in parallel formula is CT = C1 + C2 + … + Cn.

PartsSeriesParallelParallel ÷ series
10 µF + 10 µF5 µF20 µF4×
10 µF + 22 µF6.875 µF32 µF4.655×
3 × 10 µF3.333 µF30 µF9×
10 µF + 22 µF + 47 µF5.998 µF79 µF13.17×
1 µF + 100 nF90.91 nF1.1 µF12.1×

For n equal parts the gap is n², so two equal capacitors differ by 4× and three by 9×. That gives a quick sense check on any capacitors in series calculator result before parts are ordered.

The two formulas swap with resistors: capacitors in series combine like resistors in parallel. The Parallel Resistor Calculator uses the same reciprocal sum in ohms that series capacitors use in farads.

The choice is a trade. Series raises the voltage the string can hold but cuts capacitance, while parallel keeps the voltage rating of one part and adds capacitance, so a 400 V bus with 250 V parts forces series.

Electrolytic Tolerance and Worst-Case Voltage Share

A ±20% tolerance can push a nominal 50/50 capacitors in series calculator split to 60/40. Two 470 µF parts at 400 V share 200 V each on paper, but if one is 20% low and the other 20% high, the low one takes 240 V.

String at 400 VNominal share on smallestSmallest -20%, rest +20%Voltage on smallest
2 × 470 µF50%60%200 V to 240 V
3 × 470 µF33.3%42.9%133.3 V to 171.4 V
10 µF + 22 µF + 47 µF60%69.2%239.9 V to 276.8 V

The 240 V case still clears a 250 V rating, but by only 10 V. A capacitors in series calculator answer based on nominal values hides that margin, so a stack sized to the last volt can fail on parts at the edge of tolerance.

This worst case applies to switch-on and AC, where the split follows capacitance. On steady DC, balancing resistors take over and hold the split near V ÷ n whatever the tolerance.

Polarised electrolytics need one more check. CDE notes that two equal parts wired back to back, positive to positive or negative to negative, act as one non-polar capacitor of half the capacitance.

AC Reactance of a Series Chain

A series chain has more reactance than any one of its capacitors. The 5.998 µF total of 10 µF, 22 µF and 47 µF presents 442.3 Ω at 60 Hz, against 265.3 Ω for the 10 µF part alone.

XC is the reactance in ohms, f is the frequency in hertz and CT is the series total in farads. At 100 V and 60 Hz that chain draws 226.1 mA, found as V ÷ XC from the capacitors in series calculator total.

Series stringTotal50 Hz60 Hz1 kHz100 kHz
10 µF + 22 µF + 47 µF5.998 µF530.7 Ω442.3 Ω26.54 Ω265.4 mΩ
1 µF + 1 µF500 nF6.366 kΩ5.305 kΩ318.3 Ω3.183 Ω
100 nF + 220 nF68.75 nF46.3 kΩ38.58 kΩ2.315 kΩ23.15 Ω

The 50 Hz and 60 Hz columns cover mains in most of the world. A series capacitor dropper on 50 Hz mains sees 20% more reactance than the same parts on 60 Hz, so it passes 16.7% less current.

The chain behaves as one capacitor of value CT, so a capacitors in series calculator total can go straight into the Capacitor Impedance Calculator as a single part.