Capacitor code calculator that decodes markings like 104K, 4n7, 2A104J and A5 into pF, nF and µF with tolerance, voltage and dielectric codes, or finds the 3-digit code for values.
Type the code printed on the capacitor, such as 104K, 4n7, 2A104J, A5, 227 A or 1.0F.
Voltage & Dielectric Codes
How to Read This Marking
Capacitor Code Chart, 1 pF to 10 µF
| Code | IEC | pF | nF | µF |
|---|---|---|---|---|
| 1R0 / 109 | 1p0 | 1 | 0.001 | 0.000001 |
| 1R5 / 159 | 1p5 | 1.5 | 0.0015 | 0.0000015 |
| 2R2 / 229 | 2p2 | 2.2 | 0.0022 | 0.0000022 |
| 3R3 / 339 | 3p3 | 3.3 | 0.0033 | 0.0000033 |
| 4R7 / 479 | 4p7 | 4.7 | 0.0047 | 0.0000047 |
| 6R8 / 689 | 6p8 | 6.8 | 0.0068 | 0.0000068 |
| 100 | 10p | 10 | 0.01 | 0.00001 |
| 150 | 15p | 15 | 0.015 | 0.000015 |
| 220 | 22p | 22 | 0.022 | 0.000022 |
| 330 | 33p | 33 | 0.033 | 0.000033 |
| 470 | 47p | 47 | 0.047 | 0.000047 |
| 680 | 68p | 68 | 0.068 | 0.000068 |
| 101 | 100p | 100 | 0.1 | 0.0001 |
| 151 | 150p | 150 | 0.15 | 0.00015 |
| 221 | 220p | 220 | 0.22 | 0.00022 |
| 331 | 330p | 330 | 0.33 | 0.00033 |
| 471 | 470p | 470 | 0.47 | 0.00047 |
| 681 | 680p | 680 | 0.68 | 0.00068 |
| 102 | 1n0 | 1,000 | 1 | 0.001 |
| 152 | 1n5 | 1,500 | 1.5 | 0.0015 |
| 222 | 2n2 | 2,200 | 2.2 | 0.0022 |
| 332 | 3n3 | 3,300 | 3.3 | 0.0033 |
| 472 | 4n7 | 4,700 | 4.7 | 0.0047 |
| 682 | 6n8 | 6,800 | 6.8 | 0.0068 |
| 103 | 10n | 10,000 | 10 | 0.01 |
| 153 | 15n | 15,000 | 15 | 0.015 |
| 223 | 22n | 22,000 | 22 | 0.022 |
| 333 | 33n | 33,000 | 33 | 0.033 |
| 473 | 47n | 47,000 | 47 | 0.047 |
| 683 | 68n | 68,000 | 68 | 0.068 |
| 104 | 100n | 100,000 | 100 | 0.1 |
| 154 | 150n | 150,000 | 150 | 0.15 |
| 224 | 220n | 220,000 | 220 | 0.22 |
| 334 | 330n | 330,000 | 330 | 0.33 |
| 474 | 470n | 470,000 | 470 | 0.47 |
| 684 | 680n | 680,000 | 680 | 0.68 |
| 105 | 1µ0 | 1,000,000 | 1,000 | 1 |
| 155 | 1µ5 | 1,500,000 | 1,500 | 1.5 |
| 225 | 2µ2 | 2,200,000 | 2,200 | 2.2 |
| 335 | 3µ3 | 3,300,000 | 3,300 | 3.3 |
| 475 | 4µ7 | 4,700,000 | 4,700 | 4.7 |
| 685 | 6µ8 | 6,800,000 | 6,800 | 6.8 |
| 106 | 10µ | 10,000,000 | 10,000 | 10 |
Tolerance, Voltage & Dielectric Codes
Tolerance Letters
| Letter | Under 10 pF | 10 pF and Up |
|---|---|---|
| B | ±0.1 pF | ±0.1% |
| C | ±0.25 pF | ±0.25% |
| D | ±0.5 pF | ±0.5% |
| F | ±1 pF | ±1% |
| G | ±2 pF | ±2% |
| J | ±5% | ±5% |
| K | ±10% | ±10% |
| M | ±20% | ±20% |
| S | +50% / -20% | +50% / -20% |
| Z | +80% / -20% | +80% / -20% |
EIA Voltage Codes (DC)
| Code | Volts | Code | Volts |
|---|---|---|---|
| 0E | 2.5 V | 2B | 125 V |
| 0G | 4 V | 2C | 160 V |
| 0L | 5.5 V | 2Z | 180 V |
| 0J | 6.3 V | 2D | 200 V |
| 1A | 10 V | 2P | 220 V |
| 1C | 16 V | 2E | 250 V |
| 1D | 20 V | 2F | 315 V |
| 1E | 25 V | 2V | 350 V |
| 1V | 35 V | 2G | 400 V |
| 1H | 50 V | 2W | 450 V |
| 1J | 63 V | 2H | 500 V |
| 1K | 80 V | 2L | 550 V |
| 2A | 100 V | 2J | 630 V |
| 2Q | 110 V | 3A | 1,000 V |
Class 2 Dielectric Code (e.g. X7R)
| Character | Meaning |
|---|---|
| 1st: X | Lowest temperature -55 °C |
| 1st: Y | Lowest temperature -30 °C |
| 1st: Z | Lowest temperature +10 °C |
| 2nd: 4 | Highest temperature +65 °C |
| 2nd: 5 | Highest temperature +85 °C |
| 2nd: 6 | Highest temperature +105 °C |
| 2nd: 7 | Highest temperature +125 °C |
| 2nd: 8 | Highest temperature +150 °C |
| 2nd: 9 | Highest temperature +200 °C |
| 3rd: P | Change over range ±10% |
| 3rd: R | Change over range ±15% |
| 3rd: L | ±15%, down to -40% above 125 °C |
| 3rd: S | Change over range ±22% |
| 3rd: T | Change over range +22% / -33% |
| 3rd: U | Change over range +22% / -56% |
| 3rd: V | Change over range +22% / -82% |
Class 1 Dielectric Codes
| Code | Temp Coefficient | Tolerance |
|---|---|---|
| C0G (NP0) | 0 ppm/°C | ±30 ppm/°C |
| P2H | -150 ppm/°C | ±60 ppm/°C |
| R2H | -220 ppm/°C | ±60 ppm/°C |
| S2H | -330 ppm/°C | ±60 ppm/°C |
| T2H | -470 ppm/°C | ±60 ppm/°C |
| U2J | -750 ppm/°C | ±120 ppm/°C |
| M7G | +100 ppm/°C | ±30 ppm/°C |
Step-by-Step Math
Ceramic Capacitor Code Calculator Values From 1 pF to 10 µF
Code 104 is 100 nF, or 0.1 µF. The first two digits are the value and the third is the number of zeros, all in picofarads, so 104 reads as 10 followed by four zeros: 100,000 pF.
D1D2 is the two-digit number printed first, n is the third digit and CpF is the capacitance in picofarads. A third digit of 8 means × 0.01 and 9 means × 0.1, which covers values under 10 pF in a capacitor code calculator chart.
| Code | pF | nF | µF |
|---|---|---|---|
| 109 | 1 | 0.001 | 0.000001 |
| 479 | 4.7 | 0.0047 | 0.0000047 |
| 100 | 10 | 0.01 | 0.00001 |
| 220 | 22 | 0.022 | 0.000022 |
| 101 | 100 | 0.1 | 0.0001 |
| 471 | 470 | 0.47 | 0.00047 |
| 102 | 1,000 | 1 | 0.001 |
| 222 | 2,200 | 2.2 | 0.0022 |
| 472 | 4,700 | 4.7 | 0.0047 |
| 103 | 10,000 | 10 | 0.01 |
| 223 | 22,000 | 22 | 0.022 |
| 473 | 47,000 | 47 | 0.047 |
| 104 | 100,000 | 100 | 0.1 |
| 224 | 220,000 | 220 | 0.22 |
| 474 | 470,000 | 470 | 0.47 |
| 105 | 1,000,000 | 1,000 | 1 |
| 225 | 2,200,000 | 2,200 | 2.2 |
| 475 | 4,700,000 | 4,700 | 4.7 |
| 106 | 10,000,000 | 10,000 | 10 |
The same capacitor code calculator rule runs in reverse for buying parts. A 1 microfarad capacitor code is 105, a 10 nF capacitor code is 103 and 4.7 nF is 472, since each value is two digits followed by a count of zeros in pF.
Values that need three digits have no exact 3-digit capacitor code calculator answer. A 12.7 nF part rounds to 133 (13 nF) on a 3-digit marking, so precision parts print the 4-digit form 1272 instead.
For a capacitor code calculator in Excel, =LEFT(A1,2)*POWER(10,RIGHT(A1,1)) decodes any 3-digit code whose last digit is 0 to 7, in pF. Codes ending in 8 or 9 need an IF that swaps in 0.01 or 0.1 for the multiplier.
Digits 8 and 9, R and 4n7 Codes
Code 479 is 4.7 pF, not 47 billion pF. The 8 and 9 multipliers shrink the value, and they are the reason a 3-digit capacitor code calculator result can look absurd when the last digit is read as a count of zeros.
| Marking | Rule | Value |
|---|---|---|
| 47 | One or two digits are plain pF | 47 pF |
| 100 | Last 0 adds no zeros | 10 pF |
| 229 | 9 means × 0.1 | 2.2 pF |
| 108 | 8 means × 0.01 | 0.1 pF |
| 4R7 | R is the decimal point, in pF | 4.7 pF |
| 4n7 | n is the decimal point, in nF | 4.7 nF |
| .1 | A bare decimal means µF | 100 nF |
| 1002 | Three digits plus a multiplier | 10 nF |
| 107 | 7 adds seven zeros | 100 µF |
| 158 J | Tantalum or polymer: 8 adds eight zeros, J = 6.3 V | 1,500 µF |
| 1.0F | F after a decimal means farads | 1 F |
Code 100 is the classic trap. It reads like 100 pF, but the third digit 0 adds no zeros, so the part is 10 pF; 100 pF is marked 101. A 2 digit capacitor code calculator reading of "10" and a 3-digit "100" are the same 10 pF part.
The letter forms in capacitor code calculator charts come from IEC 60062, where p, n and µ (or u) mark both the unit and the decimal point. So 4n7 is 4.7 nF, 2µ2 is 2.2 µF and p47 is 0.47 pF, and an R does the same job for picofarads on SMD reels.
Older film and paper capacitors print a decimal with no unit, such as .047 or .1. That decimal is in microfarads, so .047 is 47 nF, the same part a modern ceramic marks 473.
Supercapacitors print farads directly, such as 1.0F 5.5V, a marking few capacitor code calculator charts cover. That part is 1 F, a million times a 1 µF capacitor, and at 5.5 V it holds 5.5 C of charge and about 15.1 J of energy.
Tolerance Letters and the Meter Range
A 104K capacitor is 100 nF ±10%, so a good part reads anywhere from 90 to 110 nF on a meter. The letter after the code sets how far a working part may sit from its capacitor code calculator value.
| Letter | Tolerance | Good range for 104 |
|---|---|---|
| F | ±1% | 99-101 nF |
| G | ±2% | 98-102 nF |
| J | ±5% | 95-105 nF |
| K | ±10% | 90-110 nF |
| M | ±20% | 80-120 nF |
| S | +50% / -20% | 80-150 nF |
| Z | +80% / -20% | 80-180 nF |
Below 10 pF, the letters B, C, D, F and G switch to fixed picofarads. A 4R7C part is 4.7 pF ±0.25 pF, so it may read 4.45 to 4.95 pF, a band of ±5.3%, while 4R7D allows ±0.5 pF, or ±10.6%.
A Z part can read nearly double its marking and still be in spec. Before calling an old 104Z bad, check whether the reading falls inside 80-180 nF rather than the 90-110 nF a K part would allow.
Measure out of circuit after discharging the part. Other components in parallel add their own capacitance, so an in-circuit reading rarely matches any capacitor code calculator range.
Voltage Codes Like 1E, 1H and 2A
Code 1E means 25 V DC, 1H means 50 V and 2A means 100 V. The digit sets the decade and the letter sets the leading figures, so 2A is 1.0 × 100 V and 1E is 2.5 × 10 V.
| Code | Volts | Code | Volts |
|---|---|---|---|
| 0G | 4 | 2A | 100 |
| 0J | 6.3 | 2C | 160 |
| 1A | 10 | 2D | 200 |
| 1C | 16 | 2E | 250 |
| 1E | 25 | 2G | 400 |
| 1V | 35 | 2W | 450 |
| 1H | 50 | 2J | 630 |
| 1J | 63 | 3A | 1,000 |
These codes match Nichicon's part-numbering guide, which also lists 0L = 5.5 V, 2Q = 110 V and 2Z = 180 V. On film boxes the voltage code comes first, so 2A104J reads 100 V, 100 nF, ±5%.
Tantalum parts break this pattern. AVX's TPS datasheet uses single letters: e for 2.5 V, G for 4 V, J for 6.3 V, A for 10 V, C for 16 V, D for 20 V, E for 25 V, V for 35 V and T for 50 V.
So 227 A is 220 µF at 10 V, and J 106 is 10 µF at 6.3 V. On a tantalum part, 107C is 100 µF at 16 V rather than the ±0.25% ceramic a capacitor code calculator chart would list, and the case shape is what settles which reading applies.
Large tantalum and polymer values also bend the multiplier rule. On those parts an 8 adds eight zeros, so 158 J is 1,500 µF at 6.3 V, while the same digits in a ceramic capacitor code calculator chart mean 0.15 pF.
A higher voltage rating is always a safe substitute. At its 25 V rating, a 100 nF part holds 2.5 µC and 31.3 µJ, and the Capacitor Charge and Time Constant Calculator covers charging the same part through a resistor.
X7R, C0G and Y5V Dielectric Codes
A 104K X7R capacitor can sit anywhere from 76.5 to 126 nF across -55 to +125 °C, once ±10% tolerance and X7R's ±15% temperature swing combine. No capacitor code calculator value alone reveals that swing.
| Character | Meaning |
|---|---|
| 1st: X / Y / Z | Lowest temperature -55 / -30 / +10 °C |
| 2nd: 5 / 6 / 7 / 8 | Highest temperature +85 / +105 / +125 / +150 °C |
| 3rd: P / R | Change over range ±10% / ±15% |
| 3rd: S / T | ±22% / +22% -33% |
| 3rd: U / V | +22% -56% / +22% -82% |
The letters follow the EIA class 2 table in KEMET's X7R datasheet. Y5V is the wide one: a 104M Y5V part spans 14.4 to 146 nF over -30 to +85 °C, far wider than the 104K X7R band above.
Temperature is only part of the drift. Murata notes that class 2 parts such as X5R and X7R lose capacitance under DC voltage, the DC bias effect, while C0G does not. KEMET also lists X7R ageing of up to 3% per decade of hours.
Class 1 codes read as a temperature coefficient instead. C0G, also printed NP0, is 0 ±30 ppm/°C, a 0.3% drift across a 100 °C change, while U2J is -750 ±120 ppm/°C, which falls 6.3% to 8.7% over the same change.
SMD Letter Codes and Unmarked Chips
An SMD capacitor marked A5 is 100 nF. In the EIA-198 code, the capital letter is the value and the digit is the multiplier in pF, so A = 1.0 and 5 means × 105, giving 100,000 pF.
| SMD code | Letter value | Capacitance |
|---|---|---|
| S0 | S = 4.7 | 4.7 pF |
| N2 | N = 3.3 | 330 pF |
| W2 | W = 6.8 | 680 pF |
| S3 | S = 4.7 | 4.7 nF |
| J4 | J = 2.2 | 22 nF |
| A5 | A = 1.0 | 100 nF |
| A6 | A = 1.0 | 1 µF |
The 24 capital letters A to Z, skipping I and O, map to the E24 values from 1.0 to 9.1. Lowercase letters carry extra values that differ between makers, so an SMD capacitor calculator result for a lowercase mark needs the maker's datasheet.
Most chip capacitors carry no marking at all, so no SMD capacitor code calculator can help. KEMET's X7R ordering codes list unmarked reels as standard, so an unmarked chip has to be measured or traced to its reel label.
Decoding Answers for 104 and Ceramic Parts
Most capacitor markings carry up to four pieces of information: value, tolerance, voltage and dielectric. Each answer below starts from the value code, the one part of a capacitor code calculator reading that is always present on a marked part.
How do you read a capacitor code?
Read the first two digits as the value, the third as the number of zeros, and the result in picofarads. Then read any letter after it as the tolerance and any code such as 1H or 2A as the voltage.
A film part printed 2A473J decodes as 100 V, 47 nF, ±5%. A ceramic printed 222M 1K decodes as 2.2 nF, ±20%, 80 V. Decoding a capacitor follows the same order every time: value, tolerance, then voltage.
What is a capacitor code calculator?
A capacitor code calculator converts the short marking on a capacitor into its value in pF, nF and µF, and works in reverse to find the code for a value. It saves the step of counting zeros and converting units by hand.
The conversion is a fixed rule, not a lookup, so 3-digit, 4-digit, R, IEC letter and SMD letter codes all reduce to one value in farads. Exact values matter when replacing a part: 103 and 104 differ by a factor of ten.
How do I calculate the capacitance of a ceramic capacitor?
Multiply the first two digits of the code by 10 raised to the third digit, in pF. A ceramic disc marked 473 is 47 × 103 = 47,000 pF, which is 47 nF or 0.047 µF.
Working from the plate area and gap with C = εA ÷ d only suits design work. For a ceramic that is already made, the printed code is the value to trust, checked against a meter.
What does a capacitor code like "104" mean?
Code 104 means 10 followed by four zeros, 100,000 pF, which is 100 nF or 0.1 µF. It is the standard decoupling value printed on countless ceramic discs and film parts.
At 1 kHz a 104 capacitor has a reactance of about 1.59 kΩ, at 60 Hz about 26.5 kΩ and at 1 MHz about 1.59 Ω. The Capacitor Impedance Calculator works this out at any frequency.
Why don't capacitors show values directly?
Small parts have no room for a full value. A 104 marking takes three characters where "0.1 µF" takes six, and on a 3 mm disc or a chip only a few millimetres long, three characters is often all that fits.
Larger electrolytics do print the value directly, such as 100µF 25V. Some tiny chips print nothing, which is why capacitors are coded while resistors use colour bands, decoded with the Resistor Color Code Calculator.