Chain Link Fence Calculator

Updated

Chain link fence calculator for the full bill of materials, with line and terminal posts by stretch, fabric rolls less gates, top rail, bands, ties, concrete and the material cost.

Fence Run, Height, Corners & Gates

Count every gate in the length; end posts are 0 for a run that closes on itself.

ft
ft
posts
posts
gates
gates
ft
ft
Gate Sizes, Posts, Rolls & Concrete10.0 ft spacing, 50 ft rolls
ft
ft
ft
ft
ft
in
in
in
Material Prices & Labor$1,770.25 materials
$/roll
$/stick
$/post
$/post
$/post
$/gate
$/pair
$/bag
$/ft
$/ft
Chain Link Fence Cost
$1,770.25 in Materials
$10.12 per foot for 175.0 ft of 5 ft fence
22 Posts to Set
Terminal Posts (End, Corner, Gate)6 posts
Line Posts, 10.0 ft Max Apart16 posts
Terminal posts at every end, corner and gate side, plus line posts so no gap between posts is longer than your spacing.
4 Rolls of 50 ft Fabric
Fabric Length, Gates Left Out170.0 ft
Fabric Left on the Last Roll30.0 ft
Fabric runs between gate posts but not across gate openings, rounded up to whole rolls of your roll length.
9 Top Rail Sticks, 21 ft
Tie Wires165 ties (2 bags of 100)
Tension Bands32 bands
Top rail spans the fabric run between terminal posts; ties go every 24 in on the rail and every 12 in up each line post.
26 Bags of 80 lb Concrete
Hole Depth, Gravel Included31 in
Concrete Volume15.54 cu ft
Holes four times the post diameter, 24 in deep plus 3 in for each foot of height over 4 ft, on 4 in of gravel.
Fence Run Layout Diagram4 stretches
Fence run laid out flat, 175.0 ft long4 stretches between terminal posts, 1 gateThick bars are terminal posts, thin lines are line posts, shaded spans are gates
Chain Link Fence Bill of Materials18 items
ItemQuantitySize or RuleCost
Chain link fabric4 rolls50 ft × 5 ft$380.00
Top rail9 sticks21 ft each$360.00
Terminal posts4 posts2 3/8 in OD × 7 ft 3 in$140.00
Gate posts, leaves over 4 ft2 posts2 7/8 in OD × 7 ft 8 in, 11 1/2 in × 36 in hole$110.00
Line posts16 posts1 5/8 in OD × 7 ft 3 in$320.00
Tension bars81 per end and gate post, 2 per corner-
Tension bands324 per tension bar-
Brace bands81 per rail end at a terminal-
Rail end cups81 per brace band-
Terminal post caps6Dome caps-
Line post loop caps16Top rail passes through-
Tie wires1652 bags of 100-
Fittings and ties175.0 ftPriced per foot of fence$131.25
Rail sleeves8Only for plain-end rail-
Walk gates15 ft opening$160.00
Gate hinges42 post hinges + 2 frame hinges-
Gate latches1Fork latch-
Concrete26 bags80 lb, all posts$169.00
Materials total18 lines175.0 ft of fence$1,770.25
Fittings, Posts and Concrete by HeightSame layout
Fence HeightBands per BarPost LengthHole DepthConcrete
3 ft25 ft28 in24 bags
4 ft36 ft28 in24 bags
5 ft47 ft 3 in31 in26 bags
6 ft58 ft 6 in34 in29 bags
8 ft711 ft40 in34 bags
10 ft913 ft 6 in46 in39 bags
Cost by Line Post SpacingCloser posts for slats or wind
Line Post SpacingLine PostsTie WiresMaterials Cost
6.0 ft28225$2,075.25
8.0 ft20185$1,876.25
10.0 ft16165$1,770.25
Step-by-Step Chain Link Fence Math8 steps
Fabric run175.00 ft - 5.00 ft of gates = 170.00 ft in 4 stretches
Terminal posts2 end + 2 corner + 2 × 1 gate = 6
Line postseach stretch ÷ 10.00 ft, rounded up, minus 1 = 16
Fittings8 tension bars × 4 bands = 32 bands
Fabric and rail⌈170.00 ft ÷ 50.00 ft⌉ = 4 rolls; ⌈170.00 ft ÷ 21.00 ft⌉ = 9 sticks
Tie wires⌈170.00 ft ÷ 2 ft⌉ + 16 × 5 = 165
Concrete15.54 cu ft ÷ 0.60 cu ft per bag = 26 bags
Total costpriced items in the bill of materials = $1,770.25
Set Gate Posts Wider Than the Gate
Leave about 3 3/4 in more than the gate width between gate posts for hinges and latch, so a 5 ft walk gate needs posts 5 ft 3 3/4 in apart.

Inside a Chain Link Fence Calculator Bill of Materials

A 175 ft run of 5 ft chain link with two corners, two ends and one 5 ft walk gate needs 22 posts, 4 rolls of fabric, 9 sticks of top rail and 26 bags of concrete. At the prices below it comes to $1,770.25, or $10.12 per foot.

Eighteen line items make up that chain link fence calculator list, and most of the small fittings never show up in a length-times-price estimate. Every fitting below scales with terminal posts, height or line posts, not with feet of fence alone.

ItemQuantitySize or RuleCost
Chain link fabric4 rolls50 ft × 5 ft$380.00
Top rail9 sticks21 ft each$360.00
Terminal posts42 3/8 in OD × 7 ft 3 in$140.00
Gate posts, leaves over 4 ft22 7/8 in OD × 7 ft 8 in$110.00
Line posts161 5/8 in OD × 7 ft 3 in$320.00
Tension bars81 per end and gate post, 2 per cornerIn fittings
Tension bands324 per tension barIn fittings
Brace bands and rail end cups8 each1 per rail end at a terminalIn fittings
Post caps6 dome, 16 loopLoop caps carry the top railIn fittings
Tie wires1652 bags of 100In fittings
Rail sleeves8Only for plain-end railIn fittings
Walk gate, hinges, latch1 gate, 4 hinges, 1 latch5 ft opening$160.00
Concrete26 bags80 lb, all posts$169.00
Fittings and ties175 ft$0.75 per foot of fence$131.25
Materials total175 ft (53.34 m)$10.12 per ft, $33.19 per m$1,770.25

Prices assume $95 per 50 ft roll, $40 per rail stick, $35 per terminal post, $55 per heavy gate post, $20 per line post, $160 per walk gate, $6.50 per bag and $0.75 per foot for fittings.

Swap in local prices before trusting any chain link fence calculator total, since fabric, rail and posts make up 74% of this list and move the total most.

Stretches, Not Total Length, Set the Line Post Count

Line posts go no more than 10 ft (3.05 m) apart, measured center to center along the grade, under ASTM F567 section 4.1. A chain link fence calculator post count works stretch by stretch, between terminal posts.

NL is the number of line posts, si is the length of each stretch between two terminal posts, S is the maximum spacing of 10 ft, and the brackets mean round up to the next whole number.

In a chain link fence calculator layout, the 175 ft fence loses 5 ft to the gate, leaving 170 ft split into four 42.5 ft stretches. Each needs 4 line posts at an even 8.5 ft, so the run takes 16 line posts in all.

The shortcut of total length divided by 10, minus the terminal posts, gives 175 ÷ 10 - 6 = 11.5, or 12 line posts. That is 4 short, because every corner and gate restarts the spacing and each stretch rounds up on its own.

Uneven sides shift the count too. Stretches of 25, 60, 42.5 and 42.5 ft need 2, 5, 4 and 4 line posts, or 15, so a chain link fence calculator count is closest when each side is measured on its own.

Terminal Posts Carry the Bars, Bands and Braces

Every end, corner and gate post is a terminal post, and all fabric tension pulls on it. The 175 ft fence has 2 ends, 2 corners and 2 gate posts, so 6 terminal posts hold 8 tension bars and 32 bands in the chain link fence calculator count.

What is the difference between terminal posts and line posts?

Terminal posts are larger, 2 3/8 in OD here against 1 5/8 in for line posts, because the stretched fabric is anchored to them with tension bars. Line posts only hold the fabric in line with tie wires and pass the top rail through loop caps.

Ties go about 12 in apart on line posts and 24 in apart on the top rail, per the Merchants Metals installation guide. On a 5 ft fence that is 5 ties per line post and 85 along 170 ft of rail, 165 in total.

How many tension bands and brace bands are required per terminal post?

Tension bands run one less than the fence height in feet for each tension bar, so a 5 ft fence takes 4 bands per bar. An end or gate post gets 1 bar, 4 tension bands and 1 brace band, and a corner post gets 2 bars, 8 bands and 2 brace bands.

The rule matches ASTM F567 section 9.3, which spaces tension bands no more than 15 in apart on a stretcher bar. On 60 in of fabric that works out to 4 bands, and a 6 ft fence needs 5 per bar, or 10 on a corner.

Chain link needs the bars and bands because woven fabric only stays tight when it is stretched against a rigid edge. The bar spreads the pull over the full height, and each band clamps that bar to the post.

Rolls of Fabric and Sticks of Top Rail

Fabric is bought by the roll, and gates are left out of the run because the gate frame carries its own mesh. Subtracting gate openings is the step most chain link fence calculator fabric estimates skip.

R is the number of rolls, L is the total fence length with gates included, Wg is the combined width of all gate openings, and ℓ is the roll length, usually 50 ft.

How many 50-foot rolls of chain link fabric do I need for a 175-foot fence?

Four rolls cover a 175 ft fence in any chain link fence calculator estimate. With no gate, 175 ÷ 50 = 3.5 rounds up to 4 and leaves 25 ft spare. With a 5 ft gate the fabric run is 170 ft, still 4 rolls, now with 30 ft left over.

A standard roll holds 50 ft, the length listed in the Merchants Metals guide. A 12 ft double drive gate on the same fence cuts the fabric to 158 ft, which is still 4 rolls but frees 42 ft for a short side run.

Top rail in a chain link fence calculator follows the same fabric run. At 21 ft per stick, 170 ft takes 9 sticks, and the four 42.5 ft stretches each have 2 joints, or 8 in all, that need sleeves if the rail has plain ends instead of swedged ones.

Footing Depth and Concrete by Fence Height

Posts go 24 in into the ground plus 3 in for each foot of fence over 4 ft, the ASTM F567 section 5.1 rule, on 4 in of gravel. A 5 ft fence gets 7 ft 3 in posts set 27 in deep in 31 in holes, and 26 bags of 80 lb concrete for all 22 posts.

Fence HeightBands per BarPost LengthDepth in GroundHeavy Gate Post Hole80 lb Bags
3 ft25 ft24 in36 in24
4 ft36 ft24 in36 in24
5 ft47 ft 3 in27 in36 in26
6 ft58 ft 6 in30 in36 in29
8 ft711 ft36 in40 in34
10 ft913 ft 6 in42 in46 in39
12 ft1116 ft48 in52 in45

Post length is the fence height plus the depth in the ground. The common one-third-of-the-post rule sets a 3 ft fence only 18 in deep, 6 in under the F567 minimum, and sinks an 8 ft fence 48 in where 36 in meets the standard.

In a chain link fence calculator estimate, gate posts for leaves over 4 ft go at least 36 in deep, so on fences up to 6 ft they sit lower than the rest. From 8 ft up the standard depth already passes 36 in, and the gate holes match the others.

Fences over 6 ft need braces, per F567 section 6.1. At 8 ft the 175 ft fence gets 8 brace rails with truss rods, one per tension bar, cut from 4 extra 21 ft sticks, and the chain link fence calculator total rises to $1,982.25.

A middle rail joins at 12 ft, the height where F567 recommends one, adding 9 more sticks along the 170 ft fabric run. That 12 ft fence comes to $2,413.75 in materials with 16 ft posts set 48 in deep.

V is the concrete per post, d is the post OD, k is the hole diameter as a multiple of the post OD, and h is the depth in the ground. The post's own volume is taken out of the hole.

Hole width moves chain link fence calculator concrete more than depth. A Home Depot install guide uses holes 3 times the post OD, while F567 section 5.1 calls for 4 times on posts up to 4 in OD and 3 times above that.

Hole RuleTerminal HoleGate Post HoleLine HoleConcrete80 lb Bags
3 × post OD7 1/8 in8 5/8 in4 7/8 in8.29 cu ft14
4 × post OD (ASTM F567)9 1/2 in11 1/2 in6 1/2 in15.54 cu ft26
4 × OD, line posts left dry9 1/2 in11 1/2 inNo concrete7.76 cu ft13

Following F567 nearly doubles the concrete, adding 12 bags and $78 to the 175 ft fence. Section 5.3 also asks for 2,500 psi concrete carried 2 in above grade and crowned to shed water.

For depth by soil and post size, see the Fence Post Depth Calculator, which works out hole depth and concrete per post for other fence types.

Privacy Slats and Tighter Post Spacing

Slats or privacy screen can be added to chain link, but they turn an open mesh into a solid face that catches wind. Moving line posts from 10 ft to 8 ft or 6 ft is the usual answer, and it costs posts and ties.

Line Post SpacingLine PostsTie WiresMaterials Cost
10 ft (3.05 m)16165$1,770.25
8 ft (2.44 m)20185$1,876.25
6 ft (1.83 m)28225$2,075.25

Going to 8 ft adds 4 posts and $106. Spacing at 6 ft adds 12 posts and $305 to the chain link fence calculator total before the slats themselves. If full privacy is the goal, compare that total with a solid board fence in the Wood Fence Calculator.

Can you add privacy to a chain link fence?

Yes, with slats woven into the mesh or a screen tied to it. Budget the closer line post spacing above in the chain link fence calculator estimate first, since slats added to a fence built at 10 ft spacing load posts that were sized for open mesh.

Material Cost for 200 and 500 Feet of Chain Link

A 50 × 50 ft yard, 200 ft around with one 5 ft walk gate, comes to $1,829 in materials, or $9.15 per foot. A 150 × 100 ft yard, 500 ft around with a walk gate and a 12 ft double drive gate, comes to $4,452.50, or $8.91 per foot.

Item200 ft (50 × 50 ft yard)500 ft (150 × 100 ft yard)
Fabric4 rolls, $38010 rolls, $950
Top rail10 sticks, $40023 sticks, $920
Terminal and gate posts4 + 2 heavy, $2504 + 4 heavy, $360
Line posts16, $32044, $880
Gates$160$610
Concrete26 bags, $16955 bags, $357.50
Fittings and ties$150$375
Materials total$1,829$4,452.50

Chain link fence price per foot drops as the run grows, because gates and terminal posts are fixed costs spread over more fence. A straight 200 ft run with two ends and no gate needs only 2 terminal posts and comes to $1,503.50, or $7.52 per foot.

These chain link fence calculator figures cover materials at the prices listed earlier, with labor at zero. Installed prices add a per-foot labor rate on top, and the Vinyl Fence Cost Calculator prices the same run in vinyl for comparison.

Gates Change Posts, Fabric and Spacing

Each gate adds 2 terminal posts and splits a stretch in two. Adding a 12 ft double drive gate to the 175 ft fence raises terminal posts from 6 to 8, cuts line posts from 16 to 15 and lifts the chain link fence calculator total to $2,309.25.

Gate post spacing depends on the gate. The Home Depot guide adds 3 3/4 in to the gate width for hinges and latch, so a 5 ft gate needs posts 63 3/4 in apart.

The Merchants Metals guide instead sets gate posts at the listed opening, inside face to inside face, with hinge and latch room already allowed for in the gate size.

Check the gate's own instructions before fixing the gate width in a chain link fence calculator estimate. A 3 3/4 in error either way leaves a gate that will not close or a gap at the latch.

Walk gates in the Merchants Metals range come in 39, 42 and 48 in openings, and its drive gates in 10 and 12 ft, each sized with the hinge and latch room already included.

Wide gates need heavier posts than the rest of the fence. ASTM F567 Table 2 calls for a 2 7/8 in post in a 12 in diameter, 36 in deep hole for gate leaves over 4 ft up to 10 ft, against an 8 in by 30 in hole for residential leaves of 4 ft or less.

A 5 ft walk gate counts as a wide leaf, so its 2 posts are 2 7/8 in OD and 7 ft 8 in long in 11 1/2 in holes, the 4× rule applied to that post. A 4 ft gate keeps standard posts and drops the 175 ft total to $1,717.25.

A 12 ft double drive gate hangs two 6 ft leaves, so it also takes the heavy posts in a chain link fence calculator list. That is why the drive gate above adds $110 in posts alone, on top of the $450 gate pair.

Gauge, Top Rail and Measuring Questions

Three common questions sit outside the parts list itself, covering wire thickness, the top rail and how to measure the run. Each answer below works from the same 175 ft chain link fence calculator example and its stretches.

How do you measure a chain link fence?

Measure along the ground line, gates included, and break the run at every corner, end and gate. A 50 × 40 ft yard is 180 ft around, and the Rectangle Fence Perimeter Calculator handles that step.

With a 5 ft gate on one long side, that yard has 175 ft of fabric in stretches of 22.5, 22.5, 40, 50 and 40 ft. It takes 6 terminal posts and 14 line posts, $1,727.50 in materials for a chain link fence calculator estimate at 5 ft tall.

What gauge chain link should I use?

Lower gauge numbers mean thicker wire, so 9 gauge is heavier than 11 1/2 gauge in any chain link fence calculator material list. Hoover Fence sells galvanized fabric in 11 1/2, 11 and 9 gauge, and vinyl-coated fabric in 9 and 8 gauge.

Framework is graded separately for residential and commercial work. Hoover lists residential 16 gauge pipe against commercial HF20 and industrial HF40. Gauge changes the price per roll, not the chain link fence calculator count of rolls or posts.

What is top rail and do I need it?

Top rail is the pipe along the top of the fabric that braces the whole run from end to end. ASTM F567 section 6.1 lets fabric of 6 ft or less skip terminal braces when a top rail is used, while a fence without one needs braces at every terminal.

A 175 ft fence takes 9 sticks of 21 ft rail, or 17 swedged 10 ft 6 in rails. Separately, F567 section 9.5 calls for a bottom tension wire or rail when the fabric sits more than 3 in above grade, which here means 170 ft of wire.