Conduit fill calculator for EMT, PVC, rigid and flex conduit: NEC fill percent with every ground wire counted, the smallest trade size and the most wires that one conduit can hold.
Pick the conduit, then the wires going in it; the ground wire counts toward fill too.
More Wire Sizes & Ground (EGC)
Cables, Derating & Pulling
Conduit Cross-Section Diagram
How Many Wires Fit in 3/4 in EMT
| Wire Size | THHN | XHHW-2 | TW / THW | RHW-2 |
|---|---|---|---|---|
| 14 AWG | 22 wires | 15 wires | 15 wires | 7 wires |
| 12 AWG | 16 wires | 11 wires | 11 wires | 6 wires |
| 10 AWG | 10 wires | 8 wires | 8 wires | 5 wires |
| 8 AWG | 6 wires | 5 wires | 5 wires | 2 wires |
| 6 AWG | 4 wires | 3 wires | 3 wires | 1 wire |
| 4 AWG | 2 wires | 2 wires | 1 wire | 1 wire |
| 3 AWG | 1 wire | 1 wire | 1 wire | 1 wire |
| 2 AWG | 1 wire | 1 wire | 1 wire | 1 wire |
| 1 AWG | 1 wire | 1 wire | 1 wire | 1 wire |
| 1/0 AWG | 1 wire | 1 wire | 1 wire | 1 wire |
| 2/0 AWG | 1 wire | 1 wire | 1 wire | 1 wire |
| 3/0 AWG | 1 wire | 1 wire | 1 wire | 0 wires |
| 4/0 AWG | 1 wire | 1 wire | 0 wires | 0 wires |
| 250 kcmil | 0 wires | 0 wires | 0 wires | 0 wires |
| 300 kcmil | 0 wires | 0 wires | 0 wires | 0 wires |
| 350 kcmil | 0 wires | 0 wires | 0 wires | 0 wires |
| 400 kcmil | 0 wires | 0 wires | 0 wires | 0 wires |
| 500 kcmil | 0 wires | 0 wires | 0 wires | 0 wires |
| 600 kcmil | 0 wires | 0 wires | 0 wires | 0 wires |
| 750 kcmil | 0 wires | 0 wires | 0 wires | 0 wires |
| 1000 kcmil | 0 wires | 0 wires | 0 wires | 0 wires |
EMT Conduit Fill Chart by Trade Size
| Trade Size | Inside Diameter | 100% Area | Allowed (40%) | Your Fill | Max 10 AWG THHN | Status |
|---|---|---|---|---|---|---|
| 1/2 in (16) | 0.622 in | 0.304 in² | 0.122 in² | 27.76% | 5 wires | Fits |
| 3/4 in (21) | 0.824 in | 0.533 in² | 0.213 in² | 15.83% | 10 wires | Fits |
| 1 in (27) | 1.049 in | 0.864 in² | 0.346 in² | 9.77% | 16 wires | Fits |
| 1-1/4 in (35) | 1.380 in | 1.496 in² | 0.598 in² | 5.64% | 28 wires | Fits |
| 1-1/2 in (41) | 1.610 in | 2.036 in² | 0.814 in² | 4.15% | 38 wires | Fits |
| 2 in (53) | 2.067 in | 3.356 in² | 1.342 in² | 2.51% | 63 wires | Fits |
| 2-1/2 in (63) | 2.731 in | 5.858 in² | 2.343 in² | 1.44% | 111 wires | Fits |
| 3 in (78) | 3.356 in | 8.846 in² | 3.538 in² | 0.95% | 167 wires | Fits |
| 3-1/2 in (91) | 3.834 in | 11.545 in² | 4.618 in² | 0.73% | 219 wires | Fits |
| 4 in (103) | 4.334 in | 14.753 in² | 5.901 in² | 0.57% | 279 wires | Fits |
Fill Percentage Table for 3/4 in EMT
| Wires in Conduit | Max Fill | Allowed Area | Max 10 AWG THHN | Your Fill vs Limit |
|---|---|---|---|---|
| 1 wire | 53% | 0.283 in² | fits | -- |
| 2 wires | 31% | 0.165 in² | fits | -- |
| 3 or more wires | 40% | 0.213 in² | 10 wires | 15.83% of 40% |
| Nipple, 24 in or less | 60% | 0.320 in² | 15 wires | -- |
Conduit Type Comparison
| Conduit Type | Inside Diameter | 100% Area | Your Fill at 3/4 in | Status | Smallest That Fits |
|---|---|---|---|---|---|
| EMT - Metal Tubing | 0.824 in | 0.533 in² | 15.83% | Fits | 1/2 in |
| ENT - Nonmetallic Tubing | 0.760 in | 0.454 in² | 18.59% | Fits | 1/2 in |
| FMC - Flexible Metal | 0.824 in | 0.533 in² | 15.83% | Fits | 1/2 in |
| IMC - Intermediate Metal | 0.864 in | 0.586 in² | 14.40% | Fits | 1/2 in |
| LFNC-B (Gray) | 0.830 in | 0.541 in² | 15.60% | Fits | 1/2 in |
| LFNC-A (Orange) | 0.825 in | 0.535 in² | 15.78% | Fits | 1/2 in |
| LFMC - Liquidtight Metal | 0.830 in | 0.541 in² | 15.60% | Fits | 1/2 in |
| RMC - Rigid Metal | 0.836 in | 0.549 in² | 15.37% | Fits | 1/2 in |
| PVC Schedule 80 | 0.722 in | 0.409 in² | 20.64% | Fits | 1/2 in |
| PVC Schedule 40 / HDPE | 0.804 in | 0.508 in² | 16.61% | Fits | 1/2 in |
| PVC Type A | 0.910 in | 0.650 in² | 12.98% | Fits | 1/2 in |
| PVC Type EB | -- | -- | Not made in 3/4 in | -- | 2 in |
Step-by-Step Conduit Fill Math
Conduit Fill Calculator Results for Everyday Circuits
Most branch circuits fit in 1/2 in EMT (metric 16), and fill only gets tight at feeders. The table runs common THHN circuits through the NEC Chapter 9 math, with the ground sized from the breaker.
| Circuit | THHN wires | Ground | Total area | Smallest EMT | Smallest PVC Sch 40 | Smallest PVC Sch 80 |
|---|---|---|---|---|---|---|
| 15 A, 120 V | 2 × 14 AWG | 14 AWG | 0.0291 in² (18.8 mm²) | 1/2 in, 9.57% | 1/2 in, 10.21% | 1/2 in, 13.41% |
| 20 A, 120 V | 2 × 12 AWG | 12 AWG | 0.0399 in² (25.7 mm²) | 1/2 in, 13.12% | 1/2 in, 14.00% | 1/2 in, 18.39% |
| 20 A, 240 V + neutral | 3 × 12 AWG | 12 AWG | 0.0532 in² (34.3 mm²) | 1/2 in, 17.50% | 1/2 in, 18.67% | 1/2 in, 24.52% |
| Two 20 A, 120 V circuits | 4 × 12 AWG | 12 AWG | 0.0665 in² (42.9 mm²) | 1/2 in, 21.88% | 1/2 in, 23.33% | 1/2 in, 30.65% |
| 30 A, 240 V + neutral | 3 × 10 AWG | 10 AWG | 0.0844 in² (54.5 mm²) | 1/2 in, 27.76% | 1/2 in, 29.61% | 1/2 in, 38.89% |
| 40 A range | 3 × 8 AWG | 10 AWG | 0.1309 in² (84.5 mm²) | 3/4 in, 24.56% | 3/4 in, 25.77% | 3/4 in, 32.00% |
| 50 A, 240 V + neutral | 3 × 6 AWG | 10 AWG | 0.1732 in² (111.7 mm²) | 3/4 in, 32.50% | 3/4 in, 34.09% | 1 in, 25.17% |
| 60 A subpanel | 4 × 6 AWG | 10 AWG | 0.2239 in² (144.5 mm²) | 1 in, 25.91% | 1 in, 26.91% | 1 in, 32.54% |
| 100 A feeder | 4 × 3 AWG | 8 AWG | 0.4258 in² (274.7 mm²) | 1-1/4 in, 28.46% | 1-1/4 in, 29.30% | 1-1/4 in, 34.42% |
| 200 A feeder | 4 × 3/0 AWG | 6 AWG | 1.1223 in² (724.1 mm²) | 2 in, 33.44% | 2 in, 34.10% | 2 in, 39.05% |
Each total includes the ground, so a conduit fill calculator total that skips it reads low. Every row with three or more wires is held to 40% of the conduit's inside area.
The ground sizes follow NEC Table 250.122: 14 AWG up to 15 A, 12 AWG up to 20 A, 10 AWG up to 60 A, 8 AWG up to 100 A and 6 AWG up to 200 A.
PVC Schedule 80 is the one that catches people. Its thicker wall cuts 3/4 in to 0.164 in² of usable area, so a 50 A circuit that passes in 3/4 in EMT needs 1 in Schedule 80.
Wire sizes here follow common practice; confirm yours with the Wire Size Calculator before you run conduit fill calculator numbers.
Table 1 Limits: 53, 31, 40 and 60 Percent
NEC Chapter 9 Table 1 allows 53% fill for one wire, 31% for two and 40% for three or more. Note 4 raises the limit to 60% for a nipple of 24 in (600 mm) or less between enclosures. These four limits sit behind every conduit fill calculator result.
Two wires get the lowest limit because two round wires side by side span the full diameter, so they bind at a bend before three wires that nest in a triangle.
With 40% alone, any conduit fill calculator count for one or two wires comes out wrong. The table puts each limit into square inches for 3/4 in EMT, inside diameter 0.824 in (20.9 mm).
| Wires in conduit | Max fill | Allowed area, 3/4 in EMT | Most 12 AWG THHN |
|---|---|---|---|
| 1 wire | 53% | 0.283 in² (183 mm²) | 1 |
| 2 wires | 31% | 0.165 in² (106 mm²) | 2 |
| 3 or more | 40% | 0.213 in² (137 mm²) | 16 |
| Nipple, 24 in or less | 60% | 0.320 in² (206 mm²) | 24 |
The nipple rule adds real room to any conduit fill calculator count. In 1/2 in EMT the count of 12 AWG THHN jumps from 9 to 13, and 10 AWG goes from 5 to 8. Short nipples are also exempt from ampacity adjustment, so the extra wires carry full rating.
Note 7 is the rule most charts skip. When all wires are the same size, a count that ends in .8 or more rounds up to the next whole wire. Below .8 it rounds down, even at .79.
Without the round-up, a conduit fill calculator chart comes up one wire short in each case below, where the ratio lands at .8 or higher.
| THHN size | EMT size | Allowed area ÷ wire area | Without Note 7 | With Note 7 |
|---|---|---|---|---|
| 14 AWG | 3/4 in | 21.96 | 21 | 22 |
| 8 AWG | 3/4 in | 5.82 | 5 | 6 |
| 6 AWG | 1 in | 6.82 | 6 | 7 |
| 2 AWG | 1 in | 2.99 | 2 | 3 |
| 1 AWG | 1-1/4 in | 3.83 | 3 | 4 |
| 4 AWG | 1-1/2 in | 9.88 | 9 | 10 |
The round-up never applies to mixed sizes. Once one wire differs, even a ground one size smaller, the total area must sit at or under the limit with no rounding.
Ground Wires Can Flip a Pass to a Fail
An equipment grounding conductor counts toward fill like any other wire, bare or insulated, in every conduit fill calculator total. Leaving it out is the most common way a hand count passes and the inspection fails.
A 40 A range circuit shows it. Three 8 AWG THHN use 0.1098 in², which fits the 0.122 in² allowed in 1/2 in EMT at 36.12%. Add the 10 AWG ground and the total becomes 0.1309 in², or 43.06%, so the run needs 3/4 in.
Nine 12 AWG THHN in 1/2 in EMT use 0.1197 in², just under the 0.122 in² limit. A tenth wire of the same size for the ground brings it to 0.1330 in². Note 7 can't save it, since 0.122 ÷ 0.0133 is 9.17, so the answer is still nine wires.
A bare stranded ground is smaller than an insulated one. A 10 AWG bare wire is 0.011 in² against 0.0211 in² for green THHN, per NEC Table 8.
With three 6 AWG THHN in 3/4 in EMT, a stranded bare ground drops fill from 32.50% to 30.60%. Solid bare 10 AWG is 0.008 in², which brings it to 30.04%, so check what goes on the reel.
Al Werning counts the bare ground in his worked EMT example for EC&M's guide to Chapter 9, using the Table 8 area for an 8 AWG bare conductor.
EMT, PVC and Rigid at the Same Trade Size
Trade size is a name, not a measurement. A 3/4 in raceway ranges from 0.722 in inside diameter for PVC Schedule 80 to 0.910 in for PVC Type A, and the wire count swings with it.
| Conduit type | 3/4 in inside diameter | 3/4 in total area | 40% area | 12 AWG THHN in 1/2 in | 12 AWG THHN in 3/4 in | 12 AWG THHN in 1 in |
|---|---|---|---|---|---|---|
| EMT | 0.824 in | 0.533 in² | 0.213 in² | 9 | 16 | 26 |
| RMC (rigid) | 0.836 in | 0.549 in² | 0.220 in² | 9 | 16 | 26 |
| IMC | 0.864 in | 0.586 in² | 0.235 in² | 10 | 17 | 29 |
| FMC (flex) | 0.824 in | 0.533 in² | 0.213 in² | 9 | 16 | 24 |
| LFMC (liquidtight) | 0.830 in | 0.541 in² | 0.216 in² | 9 | 16 | 26 |
| ENT | 0.760 in | 0.454 in² | 0.181 in² | 7 | 13 | 23 |
| PVC Schedule 40 | 0.804 in | 0.508 in² | 0.203 in² | 8 | 15 | 25 |
| PVC Schedule 80 | 0.722 in | 0.409 in² | 0.164 in² | 6 | 12 | 20 |
| PVC Type A | 0.910 in | 0.650 in² | 0.260 in² | 11 | 19 | 32 |
A PVC conduit fill calculator answer can't be copied onto EMT, and the reverse holds too. In 1/2 in, Schedule 80 holds 6 wires of 12 AWG where EMT holds 9.
HDPE uses the Schedule 40 dimensions in NEC Table 4, so Schedule 40 conduit fill calculator figures apply to it.
An EMT conduit fill calculator count also holds for rigid from 1/2 to 1 in, since the RMC bore is within 0.014 in of EMT at those sizes.
Flex is not always equal to EMT either. At 3/4 in the two match, but 1 in FMC has a 1.020 in bore against 1.049 in for EMT, so it holds 24 wires of 12 AWG instead of 26.
For EMT jobs, this is the THHN conduit fill calculator chart most people want. It counts same-size wires at the 40% limit with the Note 7 round-up.
| THHN size | 1/2 in EMT | 3/4 in EMT | 1 in EMT | 1-1/4 in EMT | 1-1/2 in EMT | 2 in EMT |
|---|---|---|---|---|---|---|
| 14 AWG | 12 | 22 | 35 | 61 | 84 | 138 |
| 12 AWG | 9 | 16 | 26 | 45 | 61 | 101 |
| 10 AWG | 5 | 10 | 16 | 28 | 38 | 63 |
| 8 AWG | 3 | 6 | 9 | 16 | 22 | 36 |
| 6 AWG | 2 | 4 | 7 | 11 | 16 | 26 |
| 4 AWG | 1 | 2 | 4 | 7 | 10 | 16 |
| 2 AWG | 1 | 1 | 3 | 5 | 7 | 11 |
| 1/0 AWG | 1 | 1 | 1 | 3 | 4 | 7 |
The 6 AWG count in 1/2 in shows two Table 1 rules at work. Three won't fit, and two get only 31%, so the second 6 AWG fits only because 0.094 ÷ 0.0507 is 1.85, which Note 7 rounds up to two.
Insulation Type Changes the Wire Count
Insulation, not copper, decides most of the area at small sizes. A 12 AWG wire takes 0.0133 in² as THHN but 0.0353 in² as RHW-2 with an outer cover, so the same 3/4 in EMT holds 16 or 6.
Settle the insulation before any conduit fill calculator check, since 12 AWG XHHW-2 takes 36% more room than THHN.
| Wire size | THHN / THWN-2 | XHHW-2 | TW, THW, THHW, THW-2 | RHW-2 with cover |
|---|---|---|---|---|
| 14 AWG | 0.0097 in², 22 wires | 0.0139 in², 15 wires | 0.0139 in², 15 wires | 0.0293 in², 7 wires |
| 12 AWG | 0.0133 in², 16 wires | 0.0181 in², 11 wires | 0.0181 in², 11 wires | 0.0353 in², 6 wires |
| 10 AWG | 0.0211 in², 10 wires | 0.0243 in², 8 wires | 0.0243 in², 8 wires | 0.0437 in², 5 wires |
| 8 AWG | 0.0366 in², 6 wires | 0.0437 in², 5 wires | 0.0437 in², 5 wires | 0.0835 in², 2 wires |
| 6 AWG | 0.0507 in², 4 wires | 0.0590 in², 3 wires | 0.0726 in², 3 wires | 0.1041 in², 1 wire |
Counts are for 3/4 in EMT at the 40% limit. Areas come from NEC Chapter 9 Table 5, reproduced in this ICC Table 5 sample.
THW from 14 to 8 AWG is a known trap. Table 5 lists THW, THHW and THW-2 at the TW areas, 0.0139 in² for 14 AWG. The 0.0209 in² figure belongs to RHH and RHW without an outer cover.
A conduit fill calculator chart that lists 14 AWG THW at 0.0209 in² puts 10 wires in 3/4 in EMT instead of 15. Electricians on the ECN forum traced the same mix-up to the THW rows of Annex C.
Sizing Conduit for Mixed Wire Sizes
For mixed sizes, add every wire's Table 5 area, then find the first trade size whose 40% area is equal or larger. Dividing the total by 0.40 gives the smallest total inside area that can work.
Single-size charts can't mix gauges, so mixed runs need a summed-area conduit fill calculator check. Leave out the Note 7 round-up, which only applies when every wire is the same size.
Here F is fill in percent, n is the number of wires of each size, A is the area of one wire from Table 5 or Table 8, and Ac is the conduit's total inside area from Table 4.
Take three 4 AWG THHN, one 6 AWG THHN neutral and one 8 AWG THHN ground. The total is 3 × 0.0824 + 0.0507 + 0.0366 = 0.3345 in² (215.8 mm²). That needs at least 0.3345 ÷ 0.40 = 0.836 in² of conduit.
| Conduit | 40% area at 1 in | Fill at 1 in | Smallest that passes |
|---|---|---|---|
| EMT | 0.346 in² | 38.72% | 1 in |
| RMC | 0.355 in² | 37.71% | 1 in |
| PVC Schedule 40 | 0.333 in² | 40.20% | 1-1/4 in, 23.02% |
| PVC Schedule 80 | 0.275 in² | 48.62% | 1-1/4 in, 27.04% |
The 1 in Schedule 40 run misses by 0.0015 in², a gap no puller would notice. Note 7 can't round it in because the sizes are mixed, so the code answer is 1-1/4 in.
The same sum works in a spreadsheet, the logic behind any conduit fill calculator Excel sheet. Use one row per wire size, multiply quantity by Table 5 area, total the rows, then divide by 0.40.
A circuit upsized for distance changes this math. If the Voltage Drop Calculator pushes 10 AWG to 8 AWG on a long run, rerun the conduit fill calculator total with the larger area before buying pipe.
Cat 6, Fire Alarm and Low-Voltage Cable Fill
A multiconductor cable counts as one wire under Chapter 9 Note 9, sized by its outside diameter. A flat or oval cable uses its widest dimension as the circle diameter, so read the OD from the cable spec sheet.
Here d is the cable's outside diameter and A is the area that goes into the fill total. A 0.25 in (6.4 mm) cable covers 0.0491 in².
| Cable OD | 1/2 in EMT | 3/4 in EMT | 1 in EMT | 1-1/4 in EMT | 1-1/2 in EMT | 2 in EMT |
|---|---|---|---|---|---|---|
| 0.20 in (5.1 mm) | 4 | 6 | 11 | 19 | 26 | 42 |
| 0.25 in (6.4 mm) | 2 | 4 | 7 | 12 | 16 | 27 |
| 0.30 in (7.6 mm) | 1 | 3 | 5 | 8 | 11 | 19 |
Note 7 makes small cable counts uneven. For a 0.20 in cable, 0.122 ÷ 0.0314 is 3.88 in 1/2 in EMT, which rounds up to 4. In 3/4 in it is 6.78, which rounds down to 6.
The same Note 9 method covers a fire alarm conduit fill calculator count and a Cat 6 or Cat 6A run. Cat 6 and Cat 6A ODs vary by brand and jacket rating, so use the figure for the exact cable on the reel.
For a low voltage conduit fill calculator job with mixed cables, add each cable's circle area and hold the total to 40%. Cable OD is all a conduit fill calculator by diameter needs, since Note 9 ignores the conductors inside.
A single large cable can fill 53%. The biggest single cable allowed is 0.453 in OD in 1/2 in EMT, 0.600 in in 3/4 in and 0.764 in in 1 in EMT.
Jam Ratio and the 360 Degree Bend Limit
Three single conductors can jam at a bend when 1.05 times the conduit ID divided by the wire OD falls between 2.8 and 3.2. A conduit fill calculator pass is not a pull check: three 8 AWG in 1/2 in EMT sit at 36.12% fill and a 3.02 jam ratio.
D is the conduit's inside diameter and d is one conductor's outside diameter. The 1.05 factor allows for the oval shape of the raceway at bends, as John DeDad explains in EC&M's cable pulling calculations.
| Three THHN | EMT size | Fill | Jam ratio | Jam ratio one size up |
|---|---|---|---|---|
| 8 AWG | 1/2 in | 36.12% | 3.02 | 4.01 |
| 3 AWG | 1 in | 33.78% | 3.13 | 4.12 |
| 2 AWG | 1 in | 40.21% | 2.87 | 3.77 |
| 1/0 AWG | 1-1/4 in | 37.20% | 2.98 | 3.48 |
| 3/0 AWG | 1-1/2 in | 39.47% | 2.89 | 3.72 |
| 250 kcmil | 2 in | 35.49% | 3.05 | 4.03 |
| 500 kcmil | 2-1/2 in | 36.22% | 3.02 | 3.71 |
Three 2 AWG in 1 in EMT is the worst case on the list. It reaches 40.21% and passes only through the Note 7 round-up, then lands at a jam ratio of 2.87. One size up clears both problems.
The ratio matters most for exactly three wires. NEC Chapter 9 Informational Note 2 says jamming can still occur with four or more, but the chance is very low.
Bends add a separate limit that no conduit fill calculator percentage reflects. EMT, rigid and PVC rules (358.26, 344.26 and 352.26) allow no more than 360° between pull points.
Two 90° bends, two 30° offsets and a 45° three-bend saddle add up to 390°, so that run needs a pull point partway along.
Offsets count both bends and saddles count every bend. The Offset Bend Calculator and Saddle Bend Calculator give each angle. Past 360°, a box sized with the Pull Box Sizing Calculator resets the count.
Derating After Three Current-Carrying Wires
A conduit fill calculator result tells you what fits, not what the wires can carry. Under NEC 310.15(C)(1), four to six current-carrying wires drop to 80% ampacity, seven to nine to 70%, and ten to twenty to 50%.
| EMT size | Most 12 AWG THHN | Adjustment | 12 AWG ampacity (30 A base) | Fine for 20 A breakers? |
|---|---|---|---|---|
| 1/2 in | 9 | 70% | 21 A | Yes |
| 3/4 in | 16 | 50% | 15 A | No |
| 1 in | 26 | 45% | 13.5 A | No |
| 1-1/4 in | 45 | 35% | 10.5 A | No |
Sixteen 12 AWG in 3/4 in EMT is a legal conduit fill calculator answer but useless on 20 A circuits. Past nine current-carrying 12 AWG wires, step up to 10 AWG, which drops from 40 A to 20 A at the 50% factor.
The base figures are the 90 °C THHN column of Table 310.16, and the result still can't exceed the terminal rating. The Wire Ampacity Calculator runs the full temperature and bundling correction.
Grounds never count as current-carrying. Under 310.15(E), a neutral that carries only the unbalanced current of its own circuit doesn't count either, so a 120/240 V multiwire circuit adds two, not three.
Answers on NEC Fill, Percentage and Sizing
Areas below are in square inches. Multiply by 645.16 for square millimeters, and note that metric wire sizes such as 2.5 mm² describe copper only. Convert with the AWG to mm² Calculator, then use the insulated area for fill.
Is this online Conduit Fill calculator compatible with the NEC?
A conduit fill calculator result is NEC-compatible when it uses Chapter 9 Table 1 fill limits, Table 4 conduit areas, Table 5 and Table 8 wire areas, and Notes 4, 7 and 9. Every table above uses those sources, with grounds sized from Table 250.122.
The edition your jurisdiction adopted and the local inspector have the final say. The code text itself is published by the NFPA as NFPA 70, the National Electrical Code.
How do I calculate Conduit Fill?
Add the area of every wire, ground included, and divide by the conduit's total inside area, the hand version of any conduit fill calculator result. Three 10 AWG THHN plus a 10 AWG ground total 4 × 0.0211 = 0.0844 in² (54.5 mm²).
In 3/4 in EMT, with 0.533 in² (344 mm²) inside, the fill is 0.0844 ÷ 0.533 × 100 = 15.83%. The limit for four wires is 40%, or 0.213 in², so 0.1286 in² of room is left.
What is a Conduit Fill percentage?
It is the share of the conduit's inside cross-section taken by wire insulation and copper. A 15.83% result means 15.83% of the bore is wire and 84.17% is air.
The code ceiling is 53%, 31% or 40% by wire count, and 60% for nipples. A conduit fill calculator percentage near the ceiling is legal, but expect a hard pull and more heat in the bundle.
How do I choose a conduit size?
Conduit sizing runs the conduit fill calculator math backward. Divide the total wire area by 0.40 for three or more wires, then take the first Table 4 trade size whose total area is at least that number.
For the 0.3345 in² mixed run above, that is 0.836 in², so 1 in EMT at 0.864 in² is the first size that works.
Then check the pull. If three equal wires land at a jam ratio of 2.8 to 3.2, or the run tops 360° of bends, go up one size. The Box Fill Calculator covers the boxes at each end, which follow their own volume rules.