Service Load Calculator

Updated

Service load calculator for new and existing homes under the 2023 or 2026 NEC: optional and standard methods, panel size, service wire, neutral and the room left for an EV charger.

Service Load Setup

Enter appliance nameplate watts; use 0 for anything the home does not have.

Heating & Coolingheat pump · 5,000 W cooling · 15,000 W heat
Kitchen & Fixed Appliances2 small appliance · 1 laundry · 7,950 W fixed
× 1,500 VA
× 1,500 VA
Service Voltage & Wire120/240 V · Copper
Service Size for 2,000 sq ft Home · Optional Method, 220.82, 2023 NEC
200 A Service Panel
161.5 A calculated (38,770 VA ÷ 240 V) · 175 A code minimum
38,770 VA Calculated Load
Connected Nameplate Load65,050 VA
Neutral Load (220.61)72.1 A
Total after the code demand factors, next to the full nameplate sum of every load, with the neutral current used to size the neutral wire.
2/0 AWG Copper Service Wire
Aluminum Option4/0 AWG Al
Grounding Electrode Wire4 AWG Cu
Smallest service entrance wire for the service size above at 75°C, the other metal option, and the grounding electrode wire from the same table.
231.0 A Standard Method
Standard Load55,438 VA
Service by That Method300 A
The same home worked through the other code method, so you can see which path gives the smaller service and the reason it differs.
+38.5 A Spare on 200 A
Panel Loading80.8%
Room for EV Charger80 A (19.2 kW)
Current left before reaching the service rating, how full the panel runs, and the largest standard EV charger that still fits within it.
Service Load Diagram161.5 A of 200 A
200 A = 48,000 VACalculated 38,770 VA = 161.5 A at 240 VGeneral loads: 24,020 VAHeating / cooling: 14,750 VAEV charger: 9,600 VA
Load Calculation Worksheet8 lines · 38,770 VA
LoadConnectedRuleCounted
Lighting & receptacles6,000 VA3 VA per sq ftpooled
Small appliance & laundry4,500 VA3 × 1,500 VApooled
Range / oven12,000 VAnameplatepooled
Dryer5,000 VAnameplatepooled
Water heater & fixed7,950 VAnameplatepooled
General loads total45,050 VAfirst 10,000 VA 100%, rest 40%24,020 VA
Heating / cooling20,000 VAheat pump 100% + strips 65%14,750 VA
EV charger9,600 VAnameplatepooled
Service Size and Wire Chart100 A to 600 A
ServiceCapacityYour LoadCopper WireAluminum WireElectrode WireStatus
100 A24,000 VA161.5%4 AWG Cu2 AWG Al8 AWG Cutoo small
125 A30,000 VA129.2%2 AWG Cu1/0 AWG Al8 AWG Cutoo small
150 A36,000 VA107.7%1 AWG Cu2/0 AWG Al6 AWG Cutoo small
200 A48,000 VA80.8%2/0 AWG Cu4/0 AWG Al4 AWG Curecommended
225 A54,000 VA71.8%3/0 AWG Cu250 kcmil Al4 AWG Cufits
300 A72,000 VA53.8%250 kcmil Cu350 kcmil Al2 AWG Cufits
400 A96,000 VA40.4%400 kcmil Cu600 kcmil Al1/0 AWG Cufits
600 A144,000 VA26.9%2 × 350 kcmil Cu2 × 500 kcmil Al2/0 AWG Cufits
Step-by-Step Service Load Math9 steps
General loads2,000 sq ft × 3 VA = 6,000 VA; + 2 × 1,500 small appliance + 1 × 1,500 laundry = 10,500 VA
Nameplate pool10,500 VA + 12,000 range + 5,000 dryer + 7,950 fixed + 9,600 EV = 45,050 VA
Demand (220.82(B))10,000 VA + 35,050 × 40% = 24,020 VA
Heating / cooling (220.82(C))5,000 heat pump + 15,000 strips × 65% = 14,750 VA
Total24,020 VA + 14,750 VA = 38,770 VA
Amps38,770 VA ÷ 240 V = 161.5 A
Service wire200 A × 83% = 166.0 A → 2/0 AWG Cu (175 A at 75°C)
Neutral17,313 VA ÷ 240 V = 72.1 A → 4 AWG Cu
Result200 A Service Panel
200 A Service with 2/0 AWG Copper
Use 2/0 AWG copper service wire, a 4 AWG Cu neutral and a 4 AWG copper electrode wire. A 175 A service also meets code but is a less common panel size. The panel will run above 80%, so a size up leaves room for future loads. An electrode wire that runs only to ground rods may stop at 6 AWG Cu.

Service Load Calculator Math for a 2,000 sq ft Home

A 2,000 sq ft (186 m²) all-electric home with a heat pump and a 40 A EV charger calculates to 38,770 VA, or 161.5 A at 240 V, under the 2023 NEC optional method. That lands on a 200 A service.

LoadNameplateNEC 220.82 ruleCounted
Lighting and receptacles6,000 VA3 VA per sq ftpooled
2 small-appliance + 1 laundry circuit4,500 VA1,500 VA eachpooled
Range12,000 VAnameplatepooled
Dryer5,000 VAnameplatepooled
Water heater, dishwasher, disposal, microwave, other7,950 VAnameplatepooled
EV charger9,600 VAnameplatepooled
General loads total45,050 VAfirst 10,000 VA at 100%, rest at 40%24,020 VA
Heat pump + 15 kW backup strips20,000 VAheat pump 100% + strips 65%14,750 VA
Total65,050 VA connectedsum38,770 VA

L is the calculated load in VA, P is the pooled general load including any EV charger, and H is the heating or cooling load after its own factor. Divide L by 240 V (or 208 V) to get amps.

To rebuild this as a service load calculator spreadsheet or Excel template, list each nameplate in one column, sum the pool, then take the first 10,000 VA plus 40% of the rest.

The 40% tier does most of the work. The home has 65,050 VA of nameplates, but only 38,770 VA counts, because a range, dryer, water heater and charger almost never run at full power together.

Two small-appliance circuits are the floor, not a choice. NEC 210.11(C)(1) requires at least two 20 A kitchen circuits, so every service load calculator worksheet starts with 3,000 VA for them plus 1,500 VA for laundry.

Floor area uses outside dimensions and leaves out open porches, garages and unfinished spaces. In metric terms, 3 VA per sq ft is 32.3 VA per m², so a 186 m² home carries the same 6,000 VA in a service load calculator.

161.5 A rounds to the 200 A panel most homes get. A 175 A service also meets code, but 175 A panels are uncommon, so a service load calculator answer of 161.5 A means a 200 A panel in practice.

Panel Size by House Size and Fuel Type

Fuel type moves the service size more than floor area does. A 4,000 sq ft gas home calculates to 95.8 A, while a 1,200 sq ft all-electric home with an EV charger reaches 135.7 A.

HomeGas range, dryer, water heat and furnaceAll-electric with heat pumpAll-electric + 9.6 kW EV
1,200 sq ft (111 m²)56.8 A → 100 A119.7 A → 125 A135.7 A → 150 A
2,000 sq ft (186 m²)69.1 A → 100 A145.5 A → 150 A161.5 A → 200 A
3,000 sq ft (279 m²)82.4 A → 100 A172.4 A → 200 A188.4 A → 200 A
4,000 sq ft (372 m²)95.8 A → 100 A199.3 A → 200 A215.3 A → 225 A

All rows use the 2023 optional method at 240 V. The all-electric homes have a 12 kW range, 5 kW dryer and 4.5 kW water heater, with a 3 to 9 kW heat pump and 10 to 25 kW of backup strips as size grows.

The EV charger sits in the 40% pool, as the 2023 code text reads, so it adds only 16.0 A to each all-electric home.

Every row also carries a 1,200 W dishwasher, 600 W disposal, 900 W microwave and 750 W of other fixed loads. Swap in real nameplates, since a residential service load calculator is only as good as those numbers.

NEC 230.79(C) sets 100 A as the minimum for a one-family dwelling, so every gas home in the table gets 100 A even at 56.8 A. The 4,000 sq ft gas home still uses less than 96% of it.

The largest home shows the gap between code and common sizes. At 215.3 A, 225 A covers it, but a 225 A panel is less common than 200 A or 300 A. A calculated load of 250 A needs a 300 A service; a 100 A service would cover only 40% of it.

At 240 V, a 100 A service carries 24,000 VA, 150 A carries 36,000 VA, 200 A carries 48,000 VA and 400 A carries 96,000 VA.

On a 120/208 V supply the same 200 A carries only 41,600 VA. Compare any service load calculator total in VA against those figures.

These rows double as an electrical load calculation chart for quick checks. For a permit, a service load calculator run with the home's real nameplates replaces them.

Optional Method vs Standard Method on the Same House

The optional method usually gives the smaller service, but not always. On a gas home, the standard method comes out lower, so run both service load calculator methods before picking a panel.

2,000 sq ft homeOptional (220.82)Standard (Part III)Smaller service
Gas range, dryer, water heat and furnace69.1 A → 100 A60.3 A → 100 Astandard, by 8.8 A
Gas range and furnace, electric dryer and water heater84.9 A → 100 A95.2 A → 100 Aoptional, by about 10 A
All-electric with heat pump145.5 A → 150 A191.0 A → 200 Aoptional, one size
All-electric + 9.6 kW EV161.5 A → 200 A231.0 A → 300 Aoptional, two sizes

The gas home flips because the optional method holds the first 10,000 VA at 100%. The standard method drops lighting to 35% after the first 3,000 VA, and a gas home has little else to spread.

The standard method stacks separate rules instead of one 40% tier. A 12 kW range counts 8,000 VA from Table 220.55, a dryer at least 5,000 VA, four or more fixed appliances 75%, and the largest motor gets 25% more.

The optional method only applies to a dwelling served by a single 120/240 V or 208Y/120 V set of conductors of 100 A or more, per 220.82(A).

Multifamily buildings have their own optional method in 220.84, and other buildings use the standard method, as the Electrician U standard method walkthrough sets out step by step.

Both answers are legal, so the smaller service load calculator result wins. On the all-electric home the optional method saves a full panel size, and two sizes once an EV charger is added.

That gap often decides between keeping a 200 A panel and replacing it with a 300 A one, so run the service load calculator both ways before quoting the job.

EV Chargers: 40% Pool, 100% or 2026 Rules

A 9.6 kW EV charger adds anywhere from 3,840 VA to 9,600 VA to the same service load calculator total, depending on how the edition and the inspector treat it. On a 200 A panel that is the gap between 161.5 A and 185.5 A.

EV charger2023 optional, in the 40% pool2023 optional, at 100%2026 optional (120.82)2023 standard (220.57)
None145.5 A → 150 A145.5 A → 150 A137.2 A → 150 A191.0 A → 200 A
7.2 kW (30 A)157.5 A → 200 A175.5 A → 200 A167.2 A → 200 A221.0 A → 225 A
9.6 kW (40 A)161.5 A → 200 A185.5 A → 200 A177.2 A → 200 A231.0 A → 300 A
11.5 kW (48 A)164.7 A → 200 A193.5 A → 200 A185.2 A → 200 A239.0 A → 300 A
Two 9.6 kW chargers177.5 A → 200 A225.5 A → 300 A217.2 A → 225 A271.0 A → 300 A

The base is the 2,000 sq ft all-electric home with a 5 kW heat pump and 15 kW strips. In the 2023 text, an EV charger has no line of its own in 220.82, so it falls under 220.82(B)(3) with other fixed appliances and gets the 40% factor.

Some inspectors still require it at 100%, because a charger can run near full power all night. The debate is laid out on the Mike Holt forum thread on 2023 EVSE load calculation.

The 2026 NEC settles it for new services. Section 120.82 adds the EV charger at 100%, outside the 40% tier, so this home rises from 161.5 A to 177.2 A under 2026 rules even with the lighting cut.

Under 2026 rules the charger enters every service load calculator total at full nameplate, the way many inspectors already counted it.

For a 2023 service load calculator check, ask the inspector which way they count the charger before the panel is ordered. With two 9.6 kW chargers it is the difference between 200 A and 300 A.

Under the standard method, a service load calculator total uses 7,200 VA or the nameplate, whichever is larger, under 2023 220.57. A 16 A charger rated 3,840 VA still counts 7,200 VA there; the 2026 edition lets the nameplate stand below 7,200 VA.

Heating or Cooling, Never Both

A service load counts heating or cooling, whichever is larger, because the two don't run together. A heat pump is the exception: its compressor runs with the backup strips, so both count.

2,000 sq ft home, no EVOptional: countedOptional: serviceStandard: countedStandard: service
5 kW A/C, gas heat5,000 VA104.9 A → 125 A5,000 VA128.5 A → 150 A
5 kW heat pump + 15 kW strips14,750 VA145.5 A → 150 A20,000 VA191.0 A → 200 A
15 kW electric furnace + 5 kW A/C9,750 VA124.7 A → 125 A15,000 VA165.6 A → 200 A
3 room heaters, 6 kW + 5 kW A/C5,000 VA104.9 A → 125 A6,000 VA128.1 A → 150 A
8 baseboards, 12 kW + 3 kW A/C4,800 VA104.1 A → 125 A12,000 VA153.1 A → 200 A

The optional method discounts electric heat by how it is controlled. Under 220.82(C), fewer than four separately controlled heaters count at 65%, and four or more count at 40% in optional service load calculator math.

The baseboard row shows the effect. Twelve kilowatts of heat across eight rooms counts only 4,800 VA, less than the 5,000 VA of a single central A/C unit, because eight thermostats rarely call at once.

Heat pump strips count at 65% on top of the compressor at 100%. If the controls lock the compressor out while the strips run, 220.82(C)(4) lets the compressor drop out of the heating figure.

The standard method gives no heat discount at all. That is why the electric furnace home needs 200 A under the standard method but only 125 A under the optional one. Electric heat is where a service load calculator total differs most between methods.

2026 NEC Changes: 2 VA per sq ft and the 8 kVA Tier

The 2026 NEC cuts dwelling lighting from 3 to 2 VA per sq ft and lowers the optional method's 100% tier from 10 kVA to 8 kVA. Load calculations also move from Article 220 to Article 120.

The lighting cut rests on Lawrence Berkeley National Laboratory data showing a median of 2.3 W per sq ft, as NFPA's Dean Austin explains in EC&M's review of the 2026 dwelling changes.

Home2023 optional2026 optional2023 standard2026 standard
1,200 sq ft gas56.8 A49.8 A46.3 A44.6 A
2,000 sq ft gas69.1 A60.8 A60.3 A57.3 A
2,000 sq ft all-electric145.5 A → 150 A137.2 A → 150 A191.0 A → 200 A188.1 A → 200 A
2,000 sq ft all-electric + EV161.5 A → 200 A177.2 A → 200 A231.0 A → 300 A228.1 A → 300 A
4,000 sq ft all-electric + EV215.3 A → 225 A227.6 A → 300 A302.2 A → 400 A296.4 A → 300 A

Both optional-method changes push a home without an EV down. On the 2,000 sq ft all-electric home, the lighting cut removes 800 VA after the 40% factor and the smaller tier removes 1,200 VA, a 2,000 VA drop, or about 8.3 A.

An EV charger reverses the result. Under 2026 rules the charger leaves the 40% pool and counts at 100%, so the 4,000 sq ft all-electric home climbs from 215.3 A to 227.6 A and moves from a 225 A to a 300 A service.

Branch circuit counts don't shrink with it. New section 120.13 still sets the number of general-purpose circuits at 3 VA per sq ft, so a lighter service load calculator total doesn't mean fewer breakers.

Check which edition your area has adopted before relying on 2026 figures. Many jurisdictions stay on the 2020 or 2023 NEC for years, and both use 3 VA per sq ft and the 10 kVA tier in any service load calculator.

Adding a Load to an Existing Service

An existing service is checked under NEC 220.83, which holds the first 8 kVA at 100% and the rest at 40%. Adding heating or A/C changes the rules, since the new heating or cooling counts at 100%.

New load on a 2,000 sq ft home2023 (220.83)2026 (120.83)
9.6 kW EV, all-electric, 150 A service128.4 A, fits127.8 A, fits
10 kW resistance heat, all-electric, 150 A204.1 A, needs 225 A129.1 A, fits
Second 5 kW heat pump, all-electric, 150 A183.2 A, needs 200 A117.4 A, fits
6 kW hot tub, all-electric, 100 A122.4 A, needs 125 A119.1 A, needs 125 A
9.6 kW EV, gas home, 100 A67.6 A, fits66.9 A, fits

The 2023 method counts the whole heating side at 100% once any heat or A/C is added. The heat pump home then carries both compressors and the strips in full, which is why a second heat pump breaks a 150 A service.

The 2026 edition replaces that split with one table. New EV chargers and central resistance heat count at 80% beyond the first 8 kVA, and other new loads at 50%, as electricians quote it on the Mike Holt forum's 120.83 thread.

That makes 2026 far kinder to added heating. Ten kilowatts of resistance heat on the 150 A all-electric home drops from 204.1 A to 129.1 A, while a 9.6 kW charger lands near the same figure under both editions.

The same service load calculator check can pass under one edition and fail under the other, so confirm which code your area enforces before quoting an upgrade.

The EC&M worked 220.83 example starts the same way, with 3 VA per sq ft and the first 8 kVA at 100%. An electrical service load calculator check also needs free breaker spaces and a bus rated for the service.

Conductors for 100 A to 400 A Services

A 200 A dwelling service at 120/240 V uses 2/0 AWG copper or 4/0 AWG aluminum, sized at 83% of the rating under NEC 310.12. The grounding electrode wire comes from Table 250.66.

Wire sizing is the step after the service load calculator total. The panel rating, not the calculated amps, sets the wire, so a 161.5 A load on a 200 A panel still gets 200 A conductors.

Service83% sizing currentCopper, 120/240 VAluminum, 120/240 VCopper, 120/208 VAluminum, 120/208 VElectrode wire, copper
100 A83.0 A4 AWG2 AWG3 AWG1 AWG8 AWG
125 A103.8 A2 AWG1/0 AWG1 AWG2/0 AWG8 AWG
150 A124.5 A1 AWG2/0 AWG1/0 AWG3/0 AWG6 AWG
200 A166.0 A2/0 AWG4/0 AWG3/0 AWG250 kcmil4 AWG
225 A186.8 A3/0 AWG250 kcmil4/0 AWG300 kcmil4 AWG
300 A249.0 A250 kcmil350 kcmil350 kcmil500 kcmil2 AWG
400 A332.0 A400 kcmil600 kcmil600 kcmil1000 kcmil1/0 AWG

The 83% allowance covers only 120/240 V single-phase dwelling services, so a 208 V service sizes its wire at 100% of the rating. That pushes a 200 A, 208 V service from 2/0 to 3/0 AWG copper.

A 208 V supply also divides the service load calculator total by 208, not 240. The example home reads 186.4 A there instead of 161.5 A, and a 200 A panel carries only 41,600 VA at 208 V.

The 83% rule also assumes no heat or bundling corrections. In a hot attic or a crowded raceway, size the wire from Table 310.16 with the Wire Ampacity Calculator instead.

The neutral can be smaller, because NEC 220.61 counts only line-to-neutral load and 70% of range and dryer demand. On the 2,000 sq ft home it carries 17,313 VA, or 72.1 A.

That 72.1 A fits 4 AWG copper, three sizes below the 2/0 AWG line conductors in this service load calculator example.

The electrode wire has its own caps. Under 250.66(A) and (B), a wire to ground rods never needs to exceed 6 AWG copper, and one to a concrete-encased electrode never needs to exceed 4 AWG.

A long service run can also need a size up for voltage drop, which the Voltage Drop Calculator checks. For metric cable equivalents, use the AWG to mm² Calculator.

Calculated Load, Nameplates and Circuit Counts

Each answer uses the same 2,000 sq ft heat pump home with 15 kW strips and a 40 A EV charger unless it says otherwise, under the 2023 NEC.

What is a service load calculator?

It is an NEC Article 220 dwelling calculation that turns floor area and appliance nameplates into a demand load in VA and amps. That figure sets the smallest legal service and panel size.

A free electrical load calculator, a panel load calculator and a service load calculation worksheet are the same job. The example home has 65,050 VA of nameplates but calculates to 38,770 VA, which fits a 200 A panel.

How do I use a residential load calculator?

Gather the living area from outside dimensions, the nameplate watts of the range, dryer, water heater, dishwasher and other fixed loads, the heating type and size, the A/C size and any EV charger.

Use 0 for anything the home doesn't have, and run both methods. The smaller result is legal, and on an all-electric home the optional method often saves a full panel size. A service load calculator online or on paper needs the same inputs.

What's the difference between connected load and calculated load?

Connected load is the sum of every nameplate; calculated load applies the code's demand factors. The example home has 65,050 VA connected and 38,770 VA calculated, about 60% of the total.

Breaker sizes never stand in for loads in a service load calculator total, since a 30 A dryer breaker usually feeds a dryer rated about 5,000 W, not 7,200 W.

Both run far above an electric bill. A home using 1,000 kWh a month averages about 1.4 kW, while the service must cover a cold evening peak with the range, dryer, strips and charger all on.

What's the deal with 125% for continuous loads?

Article 220 service calculations use nameplate VA without the 125% factor. The 2026 NEC states that outright, and the 9.6 kW EV charger enters the total at 9,600 VA, not 12,000 VA.

The 125% factor belongs to branch circuits and breakers. That same 40 A charger needs a 50 A breaker, which the Breaker Size Calculator works out, and wire rated for 50 A.

It still adds only 40 A to the service. Adding 125% to the charger inside a service load calculator total overstates the service.

How do I handle a house with both gas and electric appliances?

Count only the electrical nameplate of each appliance in the service load calculator total. A 2,000 sq ft home with a gas range and furnace but an electric dryer and water heater calculates to 84.9 A, so it stays on 100 A.

A gas furnace still has a blower motor, and a gas range has an igniter and controls. Add the blower's nameplate to the fixed 120 V loads; the range's small draw sits inside the small-appliance circuits.

Can I use nameplate ratings from old appliances?

Use the nameplate at the voltage the home actually has when it goes into a service load calculator. A water heater element rated 4,500 W at 240 V draws only 3,380 W on a 208 V supply, since power falls with the square of voltage.

Where a label is missing, use the maker's spec sheet for that model. For a whole existing home, NEC 220.87 also allows the past year's highest demand reading from the utility, plus 25%.

Do I really need to do a load calculation for every job?

Any new service and any load that adds to an existing one needs a calculation, and permit offices commonly ask for it. A 10 kW resistance heater on the 150 A all-electric home shows why, since it pushes the 2023 total to 204.1 A.

Small plug-in loads ride inside the 3 VA per sq ft and the small-appliance circuits, so they never need their own service load calculator line. The calculation matters for fixed loads such as EV chargers, heat pumps, hot tubs and electric heat.