Grounding Electrode Conductor Size Calculator

Updated

Grounding electrode conductor size calculator for NEC Table 250.66: size the GEC from service wire or amps, apply rod, Ufer and ring caps, then check parallel sets and the jumpers.

Grounding Electrode Conductor Setup

Pick the largest ungrounded service wire; parallel sets add their areas together.

sets
Service Wire 2/0 AWG Cu to Water Pipe or Building Steel
4 AWG Copper GEC
Table 250.66 row 2/0 or 3/0 AWG copper; main bonding jumper is the same size
133,100 cmil per Phase
Metric Area67.4 mm²
Square Inches0.1045 in²
Total cross-section of one phase after adding every parallel set together, shown in circular mils, square millimeters and square inches.
41,740 cmil GEC Area
GEC Metric Area21.1 mm²
GEC to Phase Area31.4%
Cross-section of the grounding electrode conductor this service needs, in circular mils and square millimeters, and its share of the phase.
2 AWG Aluminum GEC Option
Aluminum Metric Area33.6 mm²
Area vs Copper+59.0%
The other GEC metal where the code allows it and its area against your choice, or the electrodes where aluminum may still be used.
Row 3 of 7 in Table 250.66
Row Starts Above105,600 cmil
Row Ends At167,800 cmil
Where your phase area falls in Table 250.66, the area this row starts above, and the area where a larger GEC begins.
Grounding Electrode Diagram4 AWG Cu
SERVICE2/0 AWG Cu133,100 cmil4 AWG Cu GECrodfootingpipering
NEC Table 250.66 GEC Size Chartrow 3 of 7
Copper Service WireAluminum Service WireCopper GECAluminum GEC
2 AWG or smaller1/0 AWG or smaller8 AWG6 AWG
1 or 1/0 AWG2/0 or 3/0 AWG6 AWG4 AWG
2/0 or 3/0 AWG4/0 AWG or 250 kcmil4 AWG2 AWG
over 3/0 AWG to 350 kcmilover 250 to 500 kcmil2 AWG1/0 AWG
over 350 to 600 kcmilover 500 to 900 kcmil1/0 AWG3/0 AWG
over 600 to 1100 kcmilover 900 to 1750 kcmil2/0 AWG4/0 AWG
over 1100 kcmilover 1750 kcmil3/0 AWG250 kcmil
Service Amps to GEC Size Chart100 A to 400 A
Home ServiceCopper WireCopper GECAluminum WireGEC for Al Wire
100 A4 AWG8 AWG Cu2 AWG8 AWG Cu
110 A3 AWG8 AWG Cu1 AWG8 AWG Cu
125 A2 AWG8 AWG Cu1/0 AWG8 AWG Cu
150 A1 AWG6 AWG Cu2/0 AWG6 AWG Cu
175 A1/0 AWG6 AWG Cu3/0 AWG6 AWG Cu
200 A2/0 AWG4 AWG Cu4/0 AWG4 AWG Cu
225 A3/0 AWG4 AWG Cu250 kcmil4 AWG Cu
250 A4/0 AWG2 AWG Cu300 kcmil2 AWG Cu
300 A250 kcmil2 AWG Cu350 kcmil2 AWG Cu
350 A350 kcmil2 AWG Cu500 kcmil2 AWG Cu
400 A400 kcmil1/0 AWG Cu600 kcmil1/0 AWG Cu
EGC Size Chart (250.122)15 A to 6,000 A
Breaker or FuseCopper EGCAluminum EGC
up to 15 A14 AWG12 AWG
up to 20 A12 AWG10 AWG
up to 60 A10 AWG8 AWG
up to 100 A8 AWG6 AWG
up to 200 A6 AWG4 AWG
up to 300 A4 AWG2 AWG
up to 400 A3 AWG1 AWG
up to 500 A2 AWG1/0 AWG
up to 600 A1 AWG2/0 AWG
up to 800 A1/0 AWG3/0 AWG
up to 1,000 A2/0 AWG4/0 AWG
up to 1,200 A3/0 AWG250 kcmil
up to 1,600 A4/0 AWG350 kcmil
up to 2,000 A250 kcmil400 kcmil
up to 2,500 A350 kcmil600 kcmil
up to 3,000 A400 kcmil600 kcmil
up to 4,000 A500 kcmil750 kcmil
up to 5,000 A700 kcmil1200 kcmil
up to 6,000 A800 kcmil1200 kcmil
Step-by-Step GEC Sizing3 steps
Phase area2/0 AWG (133,100 cmil)
Table 250.66copper 2/0 or 3/0 AWG → 4 AWG Cu or 2 AWG Al
Result4 AWG Copper GEC
4 AWG Copper GEC to Water Pipe or Building Steel
This size may run along the building surface where it is not exposed to physical damage; where it is, protect it in RMC, IMC, Schedule 80 PVC, RTRC, EMT or cable armor (NEC 250.64(B)). Run it unbroken or join it only by irreversible compression or exothermic welding, and bond any ferrous metal raceway around it at both ends.

Grounding Electrode Conductor Size Calculator Chart, 100 A to 400 A

A 200 A home service on 2/0 AWG copper needs a 4 AWG copper grounding electrode conductor (GEC) under NEC Table 250.66. A 100 A service on 4 AWG copper needs 8 AWG.

ServiceCopper service wireCopper GEC, full sizeCopper GEC, rods onlyCopper GEC, Ufer onlyAluminum service wireCopper GEC for Al wire
100 A4 AWG8 AWG8 AWG8 AWG2 AWG8 AWG
125 A2 AWG8 AWG8 AWG8 AWG1/0 AWG8 AWG
150 A1 AWG6 AWG6 AWG6 AWG2/0 AWG6 AWG
175 A1/0 AWG6 AWG6 AWG6 AWG3/0 AWG6 AWG
200 A2/0 AWG4 AWG6 AWG4 AWG4/0 AWG4 AWG
225 A3/0 AWG4 AWG6 AWG4 AWG250 kcmil4 AWG
250 A4/0 AWG2 AWG6 AWG4 AWG300 kcmil2 AWG
300 A250 kcmil2 AWG6 AWG4 AWG350 kcmil2 AWG
350 A350 kcmil2 AWG6 AWG4 AWG500 kcmil2 AWG
400 A400 kcmil1/0 AWG6 AWG4 AWG600 kcmil1/0 AWG

Service wire in the table follows the 83% rule of NEC 310.12 for 120/240 V dwelling services, using 75 °C ampacity. Other services size the wire at 100%, so read the GEC from the wire actually installed.

Every grounding electrode conductor size calculator result comes from the same seven rows. The GEC tops out at 3/0 AWG copper or 250 kcmil aluminum for any service, as Table 250.66 in Tucson Electric Power's SR-601 shows.

Aluminum service wire lands in a higher row for the same amps. A 200 A service on 4/0 aluminum still sits in the 4 AWG copper row, because Table 250.66 gives aluminum its own, larger break points.

The service size behind each row comes from the load, which the Service Load Calculator works out. The GEC follows the wire chosen for that service, not the load itself.

Electrode Type Caps the GEC at 6 or 4 AWG

A GEC that runs only to ground rods never needs to be larger than 6 AWG copper or 4 AWG aluminum, and one that runs only to a concrete-encased electrode never needs more than 4 AWG copper. Those caps come from NEC 250.66(A) and (B).

Copper service wireTable 250.66 GECRod, pipe or plate onlyUfer only2 AWG ground ring only2/0 AWG ground ring only
2/0 AWG4 AWG6 AWG4 AWG4 AWG4 AWG
250 kcmil2 AWG6 AWG4 AWG2 AWG2 AWG
500 kcmil1/0 AWG6 AWG4 AWG2 AWG1/0 AWG
2 × 500 kcmil2/0 AWG6 AWG4 AWG2 AWG2/0 AWG
3 × 600 kcmil3/0 AWG6 AWG4 AWG2 AWG2/0 AWG

Before reading any cap, list every electrode on site, since one wire serving two electrodes takes the larger grounding electrode conductor size calculator result.

A ground ring's GEC is capped at the ring wire's own size under 250.66(C). The ring itself must be at least 2 AWG bare copper, so a heavier ring raises the cap with it.

The cap only applies to the part of the GEC that is the sole connection to that electrode. A single wire run first to the rods and then on to the water pipe needs 4 AWG on a 2/0 AWG service, because the rod section also carries the pipe's connection.

A common layout splits the job. Run 4 AWG copper to the water pipe and a separate 6 AWG jumper to the rods, which is the smallest legal ground rod wire for any service of 150 A or more.

For a 100 A or 125 A service, the table allows 8 AWG to the rods. Many electricians still run 6 AWG, because 8 AWG must sit in conduit or armor along its whole exposed length.

No cap applies to a metal water pipe or building steel, so a grounding electrode conductor size calculator result for those runs is the full Table 250.66 size.

Parallel Sets Use Their Combined Area

For parallel service conductors, add the area of every conductor in one phase and read Table 250.66 from that total. Two 500 kcmil copper per phase count as 1,000 kcmil and need a 2/0 AWG copper GEC.

A is the equivalent area per phase in circular mils, n is the number of conductors per phase and A1 is the area of one conductor. For 1 AWG and larger, 1 kcmil is 1,000 circular mils.

Per phaseEquivalent areaTable 250.66 rowCopper GECAluminum GECMain bonding jumper
2 × 250 kcmil Cu500 kcmil (253.4 mm²)5 of 71/0 AWG3/0 AWG1/0 AWG Cu
2 × 350 kcmil Cu700 kcmil (354.7 mm²)6 of 72/0 AWG4/0 AWG2/0 AWG Cu
2 × 600 kcmil Cu1,200 kcmil (608.0 mm²)7 of 73/0 AWG250 kcmil3/0 AWG Cu (12.5%)
4 × 600 kcmil Cu2,400 kcmil (1,216.1 mm²)7 of 73/0 AWG250 kcmil300 kcmil Cu (12.5%)
2 × 500 kcmil Al1,000 kcmil (506.7 mm²)6 of 72/0 AWG4/0 AWG4/0 AWG Al
3 × 750 kcmil Al2,250 kcmil (1,140.1 mm²)7 of 73/0 AWG250 kcmil300 kcmil Al (12.5%)

Counting one 500 kcmil conductor instead of the sum is the usual parallel-set error, and it puts a grounding electrode conductor size calculator result at 1/0 AWG, one size short.

Each parallel conductor must be 1/0 AWG or larger under NEC 310.10(G), so two 1 AWG per phase is not a legal service. The smallest parallel copper set, 2 × 1/0, adds up to 211,200 cmil and lands in the 2 AWG GEC row.

The GEC stops growing at row 7, but the main bonding jumper does not. Above 1,100 kcmil copper or 1,750 kcmil aluminum, the jumper must be at least 12.5% of the phase area.

AMBJ is the main bonding jumper area and A is the phase area from above. Four 600 kcmil sets give 2,400 kcmil, so the jumper needs 300,000 cmil, a 300 kcmil copper conductor against a 3/0 AWG GEC.

Below row 7, the main bonding jumper matches the full Table 250.66 size, even when the GEC itself is capped by an electrode rule. A 2/0 AWG copper service to rods only still needs a 4 AWG jumper, and 500 kcmil to a 2 AWG ring needs a 1/0 AWG jumper.

Aluminum Service Wire and Aluminum GECs

An aluminum GEC is allowed, but only where it stays out of the earth and out of masonry. NEC 250.64(A) also bars aluminum or copper-clad aluminum outdoors within 18 in (450 mm) of the earth.

Table 250.66 rowCopper GECCopper areaAluminum GECAluminum areaExtra metal in aluminum
18 AWG8.4 mm²6 AWG13.3 mm²+58.9%
26 AWG13.3 mm²4 AWG21.1 mm²+59.1%
34 AWG21.1 mm²2 AWG33.6 mm²+59.0%
42 AWG33.6 mm²1/0 AWG53.5 mm²+59.1%
51/0 AWG53.5 mm²3/0 AWG85.0 mm²+58.9%
62/0 AWG67.4 mm²4/0 AWG107.2 mm²+59.0%
73/0 AWG85.0 mm²250 kcmil126.7 mm²+49.0%

Aluminum runs two AWG sizes up from copper in every row, about 59% more metal, to match copper's lower resistance. The last row narrows to 49% because the table ends at 250 kcmil aluminum.

Aluminum to rods only is capped at 4 AWG aluminum, so a 200 A service needs 4 AWG Al, not the 2 AWG Al of the full table. It must still end 18 in above grade outdoors, usually with an irreversible splice to a copper tail at the rod.

Concrete-encased electrodes and ground rings put the conductor in concrete or soil, so any grounding electrode conductor size calculator answer for them is copper, even on an aluminum service.

The service conductor material and the GEC material are separate choices. Aluminum service wire sets the row by its own column, then the GEC can be copper or aluminum from that row.

Voltage-Drop Upsizing Moves the GEC Up

The GEC follows the size of the service conductor actually installed, not the breaker. Upsizing a 200 A service from 2/0 AWG to 4/0 AWG copper for a long run moves the GEC from 4 AWG to 2 AWG.

200 A service wire, copperAreaTable 250.66 rowCopper GEC
2/0 AWG (310.12 minimum)133,100 cmil34 AWG
3/0 AWG167,800 cmil34 AWG
4/0 AWG211,600 cmil42 AWG
350 kcmil350,000 cmil42 AWG
400 kcmil400,000 cmil51/0 AWG

One size up from 2/0 to 3/0 stays in the same row, so a modest upsize costs nothing at the GEC. The jump to 4/0 crosses the 167,800 cmil break and adds a size.

Run the drop first with the Voltage Drop Calculator, settle the service wire, then take the grounding electrode conductor size calculator result from that final wire. Rods-only GECs stay at 6 AWG whatever the upsize.

EGC vs GEC: Two Tables for Two Jobs

The equipment grounding conductor (EGC) is sized from the breaker under Table 250.122, while the GEC is sized from the service wire under Table 250.66. At 200 A the two differ by a size: 6 AWG EGC against a 4 AWG GEC.

Breaker or serviceCopper EGC (250.122)Aluminum EGCCopper GEC (250.66, 310.12 wire)
100 A8 AWG6 AWG8 AWG
150 A6 AWG4 AWG6 AWG
200 A6 AWG4 AWG4 AWG
300 A4 AWG2 AWG2 AWG
400 A3 AWG1 AWG1/0 AWG

The EGC carries fault current back to the breaker so it trips; the GEC ties the system to the earth for lightning and utility surges. An equipment grounding conductor size chart and a GEC chart answer different questions.

A grounding electrode conductor size calculator answer of 4 AWG at 200 A is not the wire run with a feeder, which stays at the 6 AWG EGC from Table 250.122.

The EGC to a 200 A subpanel is 6 AWG copper, but the feeder to that subpanel never gets a GEC unless the building is separate and has its own electrodes under 250.32.

When feeder or branch wires are upsized for voltage drop, 250.122(B) makes the EGC grow in proportion to the added area. The GEC needs no such step, since it is read straight from the installed service wire.

Rods, Rebar and Rings: Electrode Sizes and the 25 Ω Rule

A ground rod must be at least 8 ft (2.44 m) long with 8 ft in contact with the soil. Unlisted steel rods need a 5/8 in (15.87 mm) diameter, and listed copper-clad or stainless rods may be 1/2 in (12.7 mm).

ElectrodeNEC sectionMinimum sizeGEC cap
Metal water pipe250.52(A)(1)10 ft (3.0 m) in contact with earth, plus a supplemental electrodenone
Concrete-encased (Ufer)250.52(A)(3)20 ft (6.0 m) of 1/2 in (13 mm) rebar or 4 AWG bare copper, in 2 in (50 mm) of concrete4 AWG Cu
Ground ring250.52(A)(4)20 ft (6.0 m) of 2 AWG bare copper, 30 in (750 mm) deepring wire size
Rod or pipe250.52(A)(5)8 ft (2.44 m); rod 5/8 in or listed 1/2 in; pipe 3/4 in trade size6 AWG Cu

A single rod must measure 25 Ω or less, or it needs a second electrode under 250.53(A)(2). Once two rods are driven at least 6 ft (1.8 m) apart, no further testing is required, even if the pair reads above 25 Ω.

No grounding electrode conductor size calculator figure changes with soil resistance. The 25 Ω test decides how many electrodes go in, never the wire size to them.

Spacing farther than 6 ft improves the pair, since 8 ft rods start to share the same soil when they sit close. The City of Santee grounding guidelines quote the 25 Ω and 6 ft rules directly.

A rod that hits rock can be driven at up to 45° or laid in a trench at least 30 in (750 mm) deep. A footing with 20 ft of rebar must be used if it exists, because 250.50 requires every electrode present to be bonded together.

The water pipe connection must sit within the first 5 ft (1.52 m) of where the pipe enters the building. A pipe that has been replaced with plastic underground no longer counts, so the rods or Ufer carry the whole job.

Protection Rules for 8, 6 and 4 AWG Runs

An 8 AWG GEC must be in conduit or cable armor along its whole length, while 6 AWG copper or 4 AWG aluminum and larger may run along the building surface where not exposed to physical damage. That rule is NEC 250.64(B) in the 2023 edition.

Where a 6 AWG or larger GEC is exposed to damage, it goes in RMC, IMC, Schedule 80 PVC, RTRC, EMT or cable armor. Lorenzo Mari walks through each case in EEPower's 2023 NEC grounding and bonding series.

On a 100 A or 125 A service, the grounding electrode conductor size calculator minimum of 8 AWG often loses to 6 AWG. The larger wire costs a little more but saves a full conduit run down the wall to the rod.

A ferrous metal raceway around a GEC must be bonded at both ends under 250.64(E). Steel conduit left unbonded acts as a choke on a lightning surge, which is why PVC is the usual choice for the drop to a rod.

Where a GEC runs inside conduit, the Conduit Fill Calculator confirms the raceway size; a single 4 AWG copper GEC fits easily in 1/2 in Schedule 80 PVC.

Metric GEC Areas for IEC and India Projects

A 4 AWG copper GEC is 21.1 mm², 6 AWG is 13.3 mm² and 2/0 AWG is 67.4 mm². Those figures let an NEC GEC be compared with the metric cable sizes sold outside North America.

AWG or kcmilCircular milsArea in mm²Next IEC size up
8 AWG16,5108.410 mm²
6 AWG26,24013.316 mm²
4 AWG41,74021.125 mm²
2 AWG66,36033.635 mm²
1/0 AWG105,60053.570 mm²
2/0 AWG133,10067.470 mm²
3/0 AWG167,80085.095 mm²

One circular mil is 0.0005067 mm². The AWG to mm² Calculator converts any other size, including the service conductor that sets the Table 250.66 row.

Earthing rules under IEC 60364 and India's IS 3043 size the conductor from fault current and clearing time, not service wire size. A grounding electrode conductor size calculator India search needs that method instead.

Bare Wire, Splices and Common GEC Errors

These answers follow the 2023 NEC and assume copper conductors unless they say otherwise, matching the Table 250.66 rows above.

What is a grounding electrode conductor (GEC) size calculator?

It reads NEC Table 250.66 from the largest service conductor, or the combined area of parallel sets, and applies the electrode caps of 250.66(A) to (C). A 2/0 AWG copper service gives 4 AWG to a water pipe and 6 AWG to rods alone.

It is not an EGC tool, since the equipment grounding conductor comes from the breaker rating in Table 250.122. Grounding connects to the earth; bonding joins metal parts so they share one potential.

How big should a grounding conductor be?

A home service needs 8 AWG copper at 100 A, 6 AWG at 150 A, 4 AWG at 200 A and 1/0 AWG at 400 A, unless an electrode cap allows less.

Size it from the service conductor, not the breaker, since every grounding electrode conductor size calculator row is keyed to wire area.

An undersized GEC can overheat or burn open during a lightning strike or a utility neutral fault, leaving the system without a path to earth. Inspectors reject it, and the fix means pulling new wire.

Can grounding conductors be spliced or joined?

A GEC must run in one piece, or be joined only by irreversible compression connectors listed for grounding or by exothermic welding, under NEC 250.64(C). Split bolts and mechanical lugs are not allowed for a splice.

A busbar can also join taps from several electrodes. Each tap from the busbar is sized for the electrode it serves, so a 6 AWG tap to the rods can leave the same bar as a 4 AWG tap to the water pipe.

Why is the ground wire allowed to be bare?

NEC 250.62 lets the GEC be solid or stranded, and insulated, covered or bare. It carries no current in normal service, so insulation adds nothing for safety at the low voltage it sees.

Bare copper also resists the soil and concrete it meets at a rod or footing. Insulation matters only where an aluminum or copper-clad conductor must be kept clear of masonry and earth.

What's the most common grounding electrode mistake?

Applying the 6 AWG rod cap to a GEC that also reaches a water pipe. On a 400 A service that leaves a 6 AWG wire where Table 250.66 calls for 1/0 AWG, five sizes short.

A grounding electrode conductor size calculator check on the pipe run alone catches it, because the cap never applies to a wire that reaches the pipe.

Close behind is a lone water pipe with no supplemental electrode. Under 250.53(D)(2), the pipe must always be backed up by a rod, Ufer or other electrode, whatever its own resistance.