Lumber calculator for board feet, piece count, lengths, volume, cost and weight of any nominal or hardwood size, with wall framing, deck rows, cut lists and log rules in one place.
Pick a size or type your own; board feet use the nominal size.
Lumber Species, Waste & Tax
Nominal vs Actual Cross-Section
Best Lumber Stock Length
| Stock Length | Lumber Pieces | Board Feet | Extra Wood | Cost |
|---|---|---|---|---|
| 8 ft (Yours) | 55 | 293.33 BF | 9.1% | $233.75 |
| 10 ft | 44 | 293.33 BF | 9.1% | $233.75 |
| 12 ft | 38 | 304.00 BF | 12.3% | $242.25 |
| 14 ft | 32 | 298.67 BF | 10.7% | $238.00 |
| 16 ft | 28 | 298.67 BF | 10.7% | $238.00 |
| 18 ft | 26 | 312.00 BF | 14.5% | $248.63 |
| 20 ft | 22 | 293.33 BF | 9.1% | $233.75 |
Extra wood is length bought beyond what the job uses, waste allowance included. Cost assumes the same $0.80 per board foot at every length.
Nominal vs Actual Lumber Sizes
| Nominal Size | Actual Size | Board Feet per Foot | Weight per Foot | Board Feet in 8 ft |
|---|---|---|---|---|
| 1×2 | ¾ × 1½ in | 0.167 BF | 0.2 lb | 1.33 BF |
| 1×3 | ¾ × 2½ in | 0.250 BF | 0.4 lb | 2.00 BF |
| 1×4 | ¾ × 3½ in | 0.333 BF | 0.5 lb | 2.67 BF |
| 1×6 | ¾ × 5½ in | 0.500 BF | 0.8 lb | 4.00 BF |
| 1×8 | ¾ × 7¼ in | 0.667 BF | 1.1 lb | 5.33 BF |
| 1×10 | ¾ × 9¼ in | 0.833 BF | 1.4 lb | 6.67 BF |
| 1×12 | ¾ × 11¼ in | 1.000 BF | 1.7 lb | 8.00 BF |
| 5/4×4 | 1 × 3½ in | 0.417 BF | 0.7 lb | 3.33 BF |
| 5/4×6 | 1 × 5½ in | 0.625 BF | 1.1 lb | 5.00 BF |
| 2×2 | 1½ × 1½ in | 0.333 BF | 0.4 lb | 2.67 BF |
| 2×3 | 1½ × 2½ in | 0.500 BF | 0.7 lb | 4.00 BF |
| 2×4 (Yours) | 1½ × 3½ in | 0.667 BF | 1 lb | 5.33 BF |
| 2×6 | 1½ × 5½ in | 1.000 BF | 1.6 lb | 8.00 BF |
| 2×8 | 1½ × 7¼ in | 1.333 BF | 2.2 lb | 10.67 BF |
| 2×10 | 1½ × 9¼ in | 1.667 BF | 2.7 lb | 13.33 BF |
| 2×12 | 1½ × 11¼ in | 2.000 BF | 3.3 lb | 16.00 BF |
| 4×4 | 3½ × 3½ in | 1.333 BF | 2.4 lb | 10.67 BF |
| 4×6 | 3½ × 5½ in | 2.000 BF | 3.8 lb | 16.00 BF |
| 6×6 | 5½ × 5½ in | 3.000 BF | 6 lb | 24.00 BF |
| 8×8 | 7½ × 7½ in | 5.333 BF | 11.1 lb | 42.67 BF |
Dry dressed sizes per DOC PS 20; weight for Spruce-Pine-Fir at 15% moisture.
Lumber Weight by Species
| Species Group | NDS G | lb per cu ft | Full 1 × 12 × 12 in Board Foot | One Piece |
|---|---|---|---|---|
| Spruce-Pine-Fir (Yours) | 0.42 | 28.5 | 2.4 lb | 8.3 lb |
| Douglas Fir-Larch | 0.50 | 33.6 | 2.8 lb | 9.8 lb |
| Hem-Fir | 0.43 | 29.2 | 2.4 lb | 8.5 lb |
| Southern Pine | 0.55 | 36.7 | 3.1 lb | 10.7 lb |
| Eastern White Pine | 0.36 | 24.6 | 2.1 lb | 7.2 lb |
| Western Cedars | 0.36 | 24.6 | 2.1 lb | 7.2 lb |
| Redwood, Close Grain | 0.44 | 29.8 | 2.5 lb | 8.7 lb |
| Yellow Poplar | 0.43 | 29.2 | 2.4 lb | 8.5 lb |
| Mixed Maple | 0.55 | 36.7 | 3.1 lb | 10.7 lb |
| Red Oak | 0.67 | 44.1 | 3.7 lb | 12.9 lb |
| White Oak | 0.73 | 47.7 | 4 lb | 13.9 lb |
| Beech-Birch-Hickory | 0.71 | 46.5 | 3.9 lb | 13.6 lb |
Density at 15% moisture = 62.4 × G ÷ (1 + 0.009 × G × MC) × (1 + MC ÷ 100), with G from the NDS Supplement.
Lumber Waste Allowance
| Waste Allowance | Lumber Pieces | Board Feet | Total Length | Cost |
|---|---|---|---|---|
| 0% | 50 | 266.67 BF | 400 ft | $212.50 |
| 5% | 53 | 282.67 BF | 424 ft | $225.25 |
| 10% (Yours) | 55 | 293.33 BF | 440 ft | $233.75 |
| 15% | 58 | 309.33 BF | 464 ft | $246.50 |
| 20% | 60 | 320.00 BF | 480 ft | $255.00 |
Framers often add 10% for cutting and defects; straight runs with few cuts need less, and angled or patterned work needs more.
Step-by-Step Lumber Math
- 2×4 is sold as 2 × 4 in nominal but measures 1½ × 3½ in dry dressed (DOC PS 20).
- Board feet per piece = T × W × L(ft) ÷ 12 = 2 × 4 × 8 ÷ 12 = 5.333 BF.
- Pieces with 10% waste = ⌈50 × 1.1⌉ = 55; total length = 55 × 8 ft = 440 ft.
- Board feet = 55 × 5.333 = 293.33 BF; actual wood = 55 × 1.5 × 3.5 × 96 ÷ 1,728 = 16.04 cu ft.
- Cost = 55 × $4.25 = $233.75 ($0.80 per BF).
- Weight = 16.04 cu ft × 28.5 lb per cu ft = 458 lb total.
Lumber Calculator Basics: Board Feet From Nominal Size
Lumber yards bill softwood on its nominal size, not the planed size you carry home. A 2×4 is billed as 2 in by 4 in even though it measures 1½ by 3½, so every board-foot figure starts from the name on the tag.
T and W are nominal thickness and width in inches, and L is length in feet. With every dimension in inches, divide by 144 instead, since one board foot is 144 cubic inches, a piece 12 in wide, 12 in long and 1 in thick.
Stock thinner than 1 in is still billed as 1 in. Wood technologist Gene Wengert, citing NHLA rules on WOODWEB, notes that anything under 4/4 is charged as 4/4, so a ½ in × 6 in × 8 ft board bills 4.0 BF, not 2.0.
Hardwood follows a different habit. It is sold by quarter thickness (4/4, 5/4, 8/4) times the measured width of each random-width board, so a 4/4 board 7 in wide and 9 ft long holds 5.25 BF. Forcing a fixed 6 in width into a lumber calculator gets most hardwood tallies wrong.
| Nominal Size | 8 ft | 10 ft | 12 ft | 16 ft |
|---|---|---|---|---|
| 1×4 | 2.67 BF | 3.33 BF | 4.00 BF | 5.33 BF |
| 1×6 | 4.00 BF | 5.00 BF | 6.00 BF | 8.00 BF |
| 1×12 | 8.00 BF | 10.00 BF | 12.00 BF | 16.00 BF |
| 2×4 | 5.33 BF | 6.67 BF | 8.00 BF | 10.67 BF |
| 2×6 | 8.00 BF | 10.00 BF | 12.00 BF | 16.00 BF |
| 2×8 | 10.67 BF | 13.33 BF | 16.00 BF | 21.33 BF |
| 2×10 | 13.33 BF | 16.67 BF | 20.00 BF | 26.67 BF |
| 2×12 | 16.00 BF | 20.00 BF | 24.00 BF | 32.00 BF |
| 4×4 | 10.67 BF | 13.33 BF | 16.00 BF | 21.33 BF |
| 6×6 | 24.00 BF | 30.00 BF | 36.00 BF | 48.00 BF |
For one-off hardwood boards measured with a tape, the Board Foot Calculator suits single pieces, while whole orders need piece counts, waste and price per board foot on top of the board-foot math.
Dressed Sizes and the Wood You Actually Get
Planing and drying remove about a sixth to a third of every nominal cross-section. Under DOC PS 20, the American Softwood Lumber Standard, dry 1× stock dresses to ¾ in, 2× stock to 1½ in, and widths of 8 in and up lose ¾ in.
| Nominal | Actual Dry Size | Wood vs Nominal | SPF Weight per Foot | Southern Pine Weight per Foot |
|---|---|---|---|---|
| 1×4 | ¾ × 3½ in | 65.6% | 0.52 lb | 0.67 lb |
| 1×6 | ¾ × 5½ in | 68.8% | 0.82 lb | 1.05 lb |
| 1×12 | ¾ × 11¼ in | 70.3% | 1.67 lb | 2.15 lb |
| 5/4×6 | 1 × 5½ in | 73.3% | 1.09 lb | 1.40 lb |
| 2×4 | 1½ × 3½ in | 65.6% | 1.04 lb | 1.34 lb |
| 2×6 | 1½ × 5½ in | 68.8% | 1.63 lb | 2.10 lb |
| 2×8 | 1½ × 7¼ in | 68.0% | 2.15 lb | 2.77 lb |
| 2×10 | 1½ × 9¼ in | 69.4% | 2.75 lb | 3.54 lb |
| 2×12 | 1½ × 11¼ in | 70.3% | 3.34 lb | 4.31 lb |
| 4×4 | 3½ × 3½ in | 76.6% | 2.43 lb | 3.13 lb |
| 6×6 | 5½ × 5½ in | 84.0% | 5.99 lb | 7.72 lb |
Weights are at 15% moisture. The percentages matter whenever you fill a space: a wall of 2×6 studs is 5½ in deep, not 6 in, and twelve 2×4s laid flat cover 42 in, not 48. Feed nominal sizes to a lumber calculator for the bill, but lay out every fit with actual sizes.
Wall Framing Lumber by Stud Spacing
Framing lumber calculator counts start with one stud per spacing interval plus one to close the end, then three plates. The IRC calls for a double top plate (section R602.3.2) over a single bottom plate, so every foot of wall uses 3 ft of plate stock.
N is the stud count, L the wall length in feet and S the on-center spacing in inches. Round the division up: a 10 ft wall at 16 in needs 9 studs, and rounding down to 8 leaves the last bay wider than the spacing.
| Wall Length | Studs at 16 in | Studs at 24 in | Plate Stock | 8 ft Pieces at 16 in (+10%) | 8 ft Pieces at 24 in (+10%) |
|---|---|---|---|---|---|
| 8 ft | 7 | 5 | 24 ft | 11 | 9 |
| 12 ft | 10 | 7 | 36 ft | 18 | 15 |
| 16 ft | 13 | 9 | 48 ft | 21 | 17 |
| 20 ft | 16 | 11 | 60 ft | 28 | 22 |
| 24 ft | 19 | 13 | 72 ft | 31 | 25 |
| 32 ft | 25 | 17 | 96 ft | 41 | 32 |
| 40 ft | 31 | 21 | 120 ft | 51 | 40 |
In any lumber calculator for walls, the count covers a straight run only. Add studs for each corner, each door or window (king and jack studs) and any blocking. Shed, garage and house estimates repeat the same lumber calculator math wall by wall; size the opening headers with the Door Header Size Calculator.
Stud length comes from wall height minus the three plates. An 8 ft wall leaves 91½ in, while precut 92⅝ in studs produce a 97⅛ in wall that fits 8 ft drywall plus ceiling finish. Longer stock can yield two studs per piece: a 20 ft wall framed from 20 ft stock needs 11 pieces, 8 for studs and 3 for plates.
For opening-by-opening counts with headers and cripples, the Framing Calculator goes further than any general lumber calculator, and the Floor Joist Calculator covers the deck below the walls.
Deck and Floor Boards From Square Feet
Dividing deck area by board area undercounts in a lumber calculator for decks, because gaps and partial rows add pieces. Count rows across the width instead, using the actual face width plus the gap, then multiply by the boards each row needs along its length.
R is the row count, W the width across the boards in feet, w the actual board face in inches and g the gap in inches. The extra g on top covers the fact that the last row has no gap after it.
| Deck (Board Run × Width) | Rows at ⅛ in Gap | Boards (+10%) | 5/4×6 Board Feet | 2×6 Board Feet | Total Length |
|---|---|---|---|---|---|
| 10 × 10 ft | 22 | 25 | 137.5 BF | 220.0 BF | 220 ft |
| 12 × 12 ft | 26 | 29 | 195.0 BF | 312.0 BF | 312 ft |
| 16 × 12 ft | 26 | 29 | 260.0 BF | 416.0 BF | 416 ft |
| 12 × 16 ft | 35 | 39 | 262.5 BF | 420.0 BF | 420 ft |
| 20 × 20 ft | 43 | 48 | 537.5 BF | 860.0 BF | 860 ft |
| 24 × 12 ft (12 ft stock) | 26 | 58 | 390.0 BF | 624.0 BF | 624 ft |
Board feet and lengths are before the 10% waste. Running boards the long way saves pieces: a 12 × 16 ft deck takes 26 boards of 16 ft but 35 boards of 12 ft. Rows longer than your stock need end joints, and each joint must land on a joist.
Floors and siding use the same row count with no gap, which keeps a lumber calculator for floor boards consistent with decking. Coverage per square foot depends on the board: 5/4×6 decking runs about 1.35 BF per square foot and 2×6 about 2.17. Vertical siding layouts are easier in the Board and Batten Calculator, and subfloor sheets in the Plywood Calculator.
Pricing per Piece, Board Foot and Thousand
Retail racks price per piece, mills and wholesale yards quote per thousand board feet (MBF), and decking often sells per linear foot. Converting all three to one unit is the only fair way to compare quotes or choose a board length.
| Piece | Example Price | Board Feet | Per Board Foot | Per Thousand (MBF) | Per Linear Foot |
|---|---|---|---|---|---|
| 2×4 × 8 ft | $4.25 | 5.333 | $0.80 | $796.88 | $0.53 |
| 2×6 × 12 ft | $9.00 | 12.000 | $0.75 | $750.00 | $0.75 |
| 2×10 × 16 ft | $22.00 | 26.667 | $0.83 | $825.00 | $1.38 |
| 4×4 × 8 ft | $12.00 | 10.667 | $1.13 | $1,125.00 | $1.50 |
| 1×6 × 8 ft | $5.00 | 4.000 | $1.25 | $1,250.00 | $0.63 |
The prices are examples, not a market quote. What they show holds at any price: the cheapest piece is rarely the cheapest wood. Here the 2×6 × 12 is the best buy per board foot, while the 1×6 costs about 57% more per board foot than the 2×4.
Lumber calculator per thousand math is simple once board feet are known. An order of 293.33 BF at $750 per MBF costs 293.33 × 0.75 = $220.00 before tax. Run the same sum for each size in a lumber pricing calculator before you compare yards.
Mixed orders need waste rounded line by line, because a yard fills each size separately. Fifty 2×4 × 8 ft, twenty 2×6 × 12 ft and four 4×4 × 8 ft posts at 10% become 55, 22 and 5 pieces, and the 4 posts jump 25% from rounding alone.
That order bills 293.33 + 264.00 + 53.33 = 610.67 BF and costs $233.75 + $198.00 + $60.00 = $491.75 at the example prices, a blended $0.81 per board foot. Quote every yard on that blended rate, since one overpriced size can hide inside a low total.
Stock Lengths, Cuts and Concrete Form Boards
When a job needs many pieces of one length, the stock length decides the waste. Each saw cut also eats a kerf, about ⅛ in for a typical circular saw blade, so whole pieces per board come from this rule.
n is the number of pieces per board, L the stock length and c the cut length, both in inches, and k the kerf. Adding k on top accounts for the last piece, which needs no cut at the board end.
| Stock Length | 30 in Pieces per Board | Offcut per Board | Boards for 40 Pieces | Wood Wasted |
|---|---|---|---|---|
| 8 ft | 3 | 5⅝ in | 14 | 10.7% |
| 10 ft | 3 | 29⅝ in | 14 | 28.6% |
| 12 ft | 4 | 23½ in | 10 | 16.7% |
| 14 ft | 5 | 17⅜ in | 8 | 10.7% |
| 16 ft | 6 | 11¼ in | 7 | 10.7% |
The 10 ft board looks longer and safer, yet it wastes almost three times as much wood as the 8 ft board for 30 in parts. Work backward from your cut list before you pick a length in a lumber calculator, and compare per board foot so the longer piece earns its price.
A lumber calculator for concrete forms follows the same logic with long runs. A 4 in slab of 20 × 24 ft needs 88 ft of 2×6 edge form, the 5½ in face clearing the slab depth. Eight 12 ft or 16 ft boards close the perimeter, while 10 ft stock takes ten, so 12 ft boards at 12 BF each are the lean buy.
Weight of Lumber by Species and Moisture
Any lumber calculator weight estimate rests on species density and on how much water the wood holds. The NDS Supplement assigns each species group an oven-dry specific gravity G, listed on the American Wood Council site, and density follows from G and moisture content.
ρ is density in pounds per cubic foot and MC is moisture content in percent. Above about 30% moisture the wood stops swelling, so only the water term keeps rising; fresh-treated or green lumber can weigh far more than kiln-dried stock.
| Species Group | NDS G | lb/cu ft at 12% | lb/cu ft at 19% | 2×4 × 8 ft at 15% | Full Board Foot at 12% |
|---|---|---|---|---|---|
| Spruce-Pine-Fir | 0.42 | 28.1 | 29.1 | 8.3 lb | 2.34 lb |
| Hem-Fir | 0.43 | 28.7 | 29.7 | 8.5 lb | 2.39 lb |
| Douglas Fir-Larch | 0.50 | 33.2 | 34.2 | 9.8 lb | 2.76 lb |
| Southern Pine | 0.55 | 36.3 | 37.3 | 10.7 lb | 3.02 lb |
| Western Cedars | 0.36 | 24.2 | 25.2 | 7.2 lb | 2.02 lb |
| Redwood, Close Grain | 0.44 | 29.4 | 30.4 | 8.7 lb | 2.45 lb |
| Yellow Poplar | 0.43 | 28.7 | 29.7 | 8.5 lb | 2.39 lb |
| Red Oak | 0.67 | 43.7 | 44.6 | 12.9 lb | 3.64 lb |
| White Oak | 0.73 | 47.3 | 48.2 | 13.9 lb | 3.94 lb |
A load of 100 SPF 2×4s at 8 ft weighs about 832 lb at 15% moisture, and the same count in Southern Pine at 19% reaches 1,089 lb. Check your truck or trailer payload against the second figure, and see the Lumber Weight Calculator for single boards.
Log Scale Rules Compared
Log scaling sits apart from normal lumber calculator math: a log holds more wood than it yields as lumber, and the three US log rules disagree on how much. Purdue Extension publication FNR-191 gives a formula for each, with D as small-end diameter inside the bark in inches and L as length in feet.
The International ¼-inch rule works in 4 ft sections, each worth 0.199 d² minus 0.642 d, with d growing ½ in per section to follow the taper. It tracks real sawmill yield most closely, while Doyle's fixed 4 in slab allowance shortchanges small logs.
| Small-End Diameter | Doyle | Scribner (Formula) | International ¼-Inch | Doyle vs International |
|---|---|---|---|---|
| 8 in | 16.0 BF | 30.6 BF | 38.7 BF | -58.7% |
| 12 in | 64.0 BF | 85.8 BF | 96.9 BF | -34.0% |
| 16 in | 144.0 BF | 166.2 BF | 180.6 BF | -20.2% |
| 20 in | 256.0 BF | 272.0 BF | 289.7 BF | -11.6% |
| 24 in | 400.0 BF | 403.0 BF | 424.3 BF | -5.7% |
| 28 in | 576.0 BF | 559.4 BF | 584.4 BF | -1.4% |
| 32 in | 784.0 BF | 741.0 BF | 769.9 BF | +1.8% |
Values are for one 16 ft log. Printed tables round International figures to the nearest 5 BF and list 79 to 80 BF for the 12 in Scribner log, a few percent under the formula. For hauling, the Log Weight Calculator covers green log weight.
Answers on Lumber Sizes, Cost and Board Feet
The questions below come up most when people plan a lumber order. Each answer uses the same board-foot, sizing and weight rules worked through above, with numbers you can check by hand.
How do I calculate lumber volume?
Multiply actual thickness, width and length in inches, then divide by 1,728 for cubic feet. An 8 ft 2×4 holds 1.5 × 3.5 × 96 ÷ 1,728 = 0.29 cu ft, and 55 of them hold 16.04 cu ft of real wood.
Billed volume is different. Those 55 pieces bill 293.33 BF, which equals 24.44 cu ft at nominal size, so you receive 65.6% of the volume the board feet imply.
How do I calculate board feet of lumber?
Multiply nominal thickness and width in inches by length in feet, then divide by 12. A 2×10 × 16 ft piece is 2 × 10 × 16 ÷ 12 = 26.67 BF, and a dozen of them total 320 BF before any waste allowance.
How do I use lumber?
Match the stock to the job before it goes into a lumber calculator for building work. 1× boards serve trim, shelving and fence pickets; 2× dimension lumber frames walls, floors and rafters; 4×4 and 6×6 posts carry decks and pergolas; and pressure-treated stock goes wherever wood touches soil or concrete.
Structural members such as joists, beams and headers must be sized for their span and load, so check them with the Wood Beam Span Calculator rather than by eye.
How is lumber measured?
Softwood is named by nominal thickness and width in inches and sold in lengths of whole feet, usually even numbers from 8 to 20 ft. Hardwood is measured in quarter inches of rough thickness, such as 4/4 or 8/4, and by the actual width of each board.
The quantity unit varies: board feet for most hardwood and wholesale softwood, pieces at retail, and linear feet for decking, trim and siding.
How do you read lumber sizes?
Read thickness first, then width, then length: 2×6 × 12 means 2 in nominal thick, 6 in nominal wide, 12 ft long. Subtract ½ in from nominal 2× thickness and from widths up to 6 in, and ¾ in from widths of 8 in and more, to get the dry dressed size under PS 20.
How much does lumber weigh?
Kiln-dried framing lumber weighs roughly 28 to 37 lb per cubic foot, depending on species. An 8 ft 2×4 weighs about 8.3 lb in Spruce-Pine-Fir and 10.7 lb in Southern Pine at 15% moisture; wet treated lumber weighs considerably more.
How much waste factor should I add to my lumber estimate?
Add 10% for typical framing and decking, the default most lumber calculator estimates use. Straight runs cut from matched lengths can drop to 5%, while angled decks, diagonal layouts and lots of short parts can need 15% to 20%.
On 50 pieces, 10% means 55 pieces and 15% means 58. Check the cut list too: 30 in parts waste 10.7% from 8 ft stock but 28.6% from 10 ft stock before any allowance.
How much does framing lumber cost?
Cost equals board feet times the price per board foot, plus tax. At an example $0.80 per BF, a 20 ft wall framed at 16 in with 28 pieces of 2×4 × 8 ft (149.33 BF) costs about $119; check your yard's current rack price, since framing lumber trades as a commodity.
Is this calculator accurate for hardwoods too?
Hardwood board feet come out right in a lumber calculator when entered by quarter thickness and measured width. NHLA tallies hardwood that way, so a 4/4 board 7 in wide and 9 ft long is 5.25 BF and an 8/4 board 6 in wide and 10 ft long is 10.0 BF.
Surfaced hardwood still bills on rough thickness. A 4/4 board surfaced two sides measures 13/16 in, and an 8/4 board measures 1¾ in.
How do I figure out how much lumber a project needs?
Break the project into parts, since a lumber calculator count follows a different rule for each part. Walls take studs per spacing plus three plates, decks take rows across the width, and cut parts take whole pieces per board. Then add waste and convert to board feet for pricing.
A wood calculator for project lists works the same way, part by part. A 12 × 16 ft shed with four 8 ft walls at 16 in on center needs about 70 studs and plate pieces from 8 ft stock before corners and openings, using the wall table above.
Why do lumber prices change so much?
Softwood lumber trades as a commodity priced per thousand board feet, so housing starts, mill output, freight costs and US duties on Canadian softwood all move it. Retail racks follow wholesale with a lag, which is why the same 2×4 can change price between two visits.
Can I burn pressure-treated lumber?
Pressure-treated lumber should not be burned. The US EPA advises against burning treated wood in fireplaces, stoves or open fires because the preservative chemicals end up in the smoke and ash. Send offcuts to a landfill or a disposal site that accepts treated wood.
What is the difference between nominal and actual lumber dimensions?
Nominal is the trade name and billing size; actual is the size after drying and planing. A nominal 2×4 measures 1½ × 3½ in, a 2×10 measures 1½ × 9¼ in and a 6×6 measures 5½ × 5½ in, so you receive 65.6% to 84% of the nominal cross-section.
What's the most common mistake people make when buying lumber?
Laying out with nominal sizes. Eight 2×6 boards side by side cover 44 in, not 48 in, so a deck planned on nominal widths comes up short. Close behind is skipping the waste allowance and buying lengths that waste a third of each board.
How do I store lumber so it doesn't warp?
Store it flat, off the ground, on evenly spaced supports, with stickers between layers so air reaches every face. Keep stickers aligned top to bottom about every 16 to 24 in, cover the top but not the sides, and let new lumber acclimate where it will be installed.
How do you calculate the board feet in a log?
Measure the small end inside the bark, then apply a log rule. A 12 in × 16 ft log scales 64 BF by Doyle, (12 - 4)² × 16 ÷ 16, about 86 BF by the Scribner formula and about 97 BF by the International ¼-inch rule.
Agree on the rule before a sale. On a 12 in log, Doyle scales 34% below International, and the gap only closes near 28 in in diameter.
How many sheets of plywood do I need?
Divide the area by 32 sq ft for standard 4 × 8 ft sheets and round up. A 12 × 16 ft floor is 192 sq ft, or 6 sheets, and 7 sheets with a 10% allowance for cuts.
What's the difference between board feet and the volume this calculator shows?
Board feet measure billed nominal volume, while cubic feet of actual wood measure what you receive. For 55 pieces of 2×4 × 8 ft, 293.33 BF equals 24.44 cu ft billed, but the planed boards hold 16.04 cu ft, the volume that sets weight.
How do you calculate board feet?
With all dimensions in inches, multiply thickness, width and length and divide by 144. A 1 in × 8 in board 120 in long is 1 × 8 × 120 ÷ 144 = 6.67 BF; with length in feet, the same board is 1 × 8 × 10 ÷ 12.
What is the cheapest wood for building projects?
Construction-grade softwoods such as Spruce-Pine-Fir and Southern Pine usually cost least per board foot. Compare by board foot rather than by piece: in the example prices above, a 1×6 costs $1.25 per BF while a 2×6 × 12 costs $0.75.
Should I use actual or nominal dimensions in the calculator?
Use nominal sizes for dimension lumber bought by its trade name, since yards bill board feet on nominal size. Use actual measured sizes for rough or custom-milled stock, where a 1.5 × 3.5 in 8 ft piece is 3.5 BF instead of 5.33.
How much does a board foot of oak weigh?
A full board foot (1 × 12 × 12 in) of red oak weighs about 3.64 lb at 12% moisture, and white oak about 3.94 lb, from NDS specific gravities of 0.67 and 0.73. Green oak straight from the sawmill weighs much more.
How many board feet are in a 2×4?
An 8 ft 2×4 holds 5.33 BF, a 10 ft holds 6.67, a 12 ft holds 8.00 and a 16 ft holds 10.67. Each foot of 2×4 is two-thirds of a board foot on the bill, though the planed wood equals only 0.44 BF per foot. That two-thirds figure is what every lumber calculator board feet total is built from.
What is a board foot insulation?
In spray foam, a board foot is 1 sq ft of coverage 1 in thick, the same 144 cu in as a lumber board foot. Spraying 3 in of foam over 500 sq ft takes 1,500 board feet of foam.
Can I use this for plywood and sheet goods?
Sheet goods are counted by sheets, not board feet, since a ¾ in 4 × 8 sheet is billed per sheet. Divide the area by 32 sq ft per sheet, as in the 192 sq ft floor that needs 6 sheets, or use the Plywood Calculator for cut layouts.
How many 2×6 boards do I need for a 12×16 deck?
Running the boards along the 16 ft side, 26 rows of 2×6 cover the 12 ft width at a ⅛ in gap, or 29 boards of 16 ft with 10% waste. Running them along the 12 ft side takes 35 rows, or 39 boards of 12 ft.
Each row is 5½ in of board plus the ⅛ in gap, 5⅝ in in all, so 144 in of width needs 26 rows with a sliver trimmed off the last one.
How do you measure a board foot?
Measure thickness and width in inches and length in feet. For rough hardwood, round thickness to the nearest quarter and measure width at the narrow point; for dimension lumber, read the nominal size from the tag rather than measuring.
How many board feet are there in 320 square feet?
It depends on the board covering it. Laid tight, 1×6 boards covering 320 sq ft add up to about 349 BF and 1×4 boards about 366 BF, because each board bills on 6 or 4 in but covers only 5½ or 3½ in.
The same area in 2×6 decking bills about 698 BF, which is why a lumber calculator square feet entry needs the board size. Only a 1 in thick sheet with no width loss would equal 320 BF.
What is the difference between a board foot and a linear foot?
A linear foot is 1 ft of length of any size, while a board foot is a fixed volume of 144 cu in. One linear foot of 2×4 is 0.667 BF, one linear foot of 2×12 is 2.0 BF, and one linear foot of 1×12 is exactly 1 BF.
What is the actual length of an 8 foot 2×4?
An 8 ft 2×4 is the full 96 in long; dressing shrinks only its thickness and width. Precut studs are a separate item at 92⅝ in, sized so three 1½ in plates make a 97⅛ in wall.