Wood beam span calculator for floor and roof beams that checks bending, shear and sag against NDS design values for 33 wood species, from 2x8 built-up beams to 4x12s and LVL sizes.
Enter the total load per foot along the beam, dead plus live.
Point Load and Design Factors
Wood Beam Span Chart
| Beam | Max Span at Your Load | Max Load at 12 ft | At 12 ft |
|---|---|---|---|
| 2x6 | 5 ft 5 in | 29 plf | Too weak |
| 2x8 | 6 ft 10½ in | 65 plf | Too weak |
| 2x10 | 8 ft 4¾ in | 98 plf | Too weak |
| 2-ply 2x6 | 7 ft 8 in | 57 plf | Too weak |
| 2x12 | 9 ft 8¾ in | 132 plf | Too weak |
| 4x6 | 8 ft 3½ in | 67 plf | Too weak |
| 2-ply 2x8 | 9 ft 8½ in | 131 plf | Too weak |
| 3-ply 2x6 | 9 ft ½ in | 86 plf | Too weak |
| 4x8 | 10 ft 11 in | 152 plf | Too weak |
| 2-ply 2x10 | 11 ft 10½ in | 196 plf | Too weak |
| 4x10 | 13 ft 4¾ in | 250 plf | Works |
| 3-ply 2x8 | 11 ft 10¾ in | 196 plf | Too weak |
| 2-ply 2x12 | 13 ft 9¼ in | 264 plf | Works |
| 4x12 | 15 ft 7¼ in | 338 plf | Works |
| 6x8 | 12 ft 3 in | 209 plf | Works |
| 3-ply 2x10 | 14 ft 6½ in | 294 plf | Works |
| 3-ply 2x12 | 16 ft 10½ in | 396 plf | Works |
| 6x10 | 15 ft 6¼ in | 335 plf | Works |
| 6x12 | 18 ft 9½ in | 491 plf | Works |
| 6x14 | 21 ft 11 in | 668 plf | Works |
| 6x16 | 24 ft 11¾ in | 867 plf | Works |
| 8x12 | 20 ft 11 in | 670 plf | Works |
| 8x14 | 24 ft 6½ in | 911 plf | Works |
| 8x16 | 28 ft 2¼ in | 1,182 plf | Works |
Beam Load Diagram
Step-by-Step Beam Math
- Section: b = 2 × 1.5 in = 3 in, d = 11.25 in; S = b × d² ÷ 6 = 63.3 in³; I = b × d³ ÷ 12 = 356 in⁴; A = b × d = 33.8 in².
- Allowed bending: Fb′ = Fb × CD × CM × Ci × CF × Cr = 900 psi × 1 × 1 × 1 × 1 × 1 = 900 psi (NDS Supplement Table 4A, Douglas Fir-Larch No. 2).
- Allowed shear and stiffness: Fv′ = Fv × CD × CM × Ci = 180 psi × 1 × 1 × 1 = 180 psi; E′ = E × CM × Ci = 1,600,000 psi × 1 × 1 = 1,600,000 psi.
- Uniform load: w = 200 plf, no point load.
- Bending: M = w × L² ÷ 8 + P × L ÷ 4 = 43,200 lb·in; fb = M ÷ S = 683 psi, which is 76% of Fb′.
- Shear: V = w × L ÷ 2 + P ÷ 2 = 1,200 lb; fv = 1.5 × V ÷ A = 53 psi, which is 30% of Fv′.
- Sag: δ = 5 × w × L⁴ ÷ (384 × E′ × I) + P × L³ ÷ (48 × E′ × I) = 0.16 in against L/360 = 0.4 in.
- Bearing: length = R ÷ (b × Fc⊥′) = 1,200 lb ÷ (3 in × 625 psi) = 0.64 in; IRC R502.6 asks for at least 1½ in on wood or metal and 3 in on masonry or concrete.
- Max span: the longest L that keeps bending, shear and sag inside their limits is 13 ft 9¼ in.
- Result: 13 ft 9¼ in Max Span for a 2-ply 2x12 Douglas Fir-Larch No. 2.
Wood Beam Span Calculator Chart for Floor Beams
A wood beam span calculator answers one job question: how far a beam of a given size, species and grade can reach before bending, shear or sag goes past its limit. For a floor beam the answer depends mostly on tributary width, which is half the joist span on each side of the beam.
The chart below covers Douglas Fir-Larch No. 2 carrying a 40 psf live load and a 10 psf dead load, the IRC Table R301.5 values for living areas. Sag is held to L/360 under live load and L/240 under total load, with no repetitive-member increase.
| Beam (DF-L No. 2) | 4 ft tributary | 6 ft tributary | 8 ft tributary | 10 ft tributary | 12 ft tributary |
|---|---|---|---|---|---|
| 2-ply 2x8 | 9 ft 8½ in | 7 ft 11¼ in | 6 ft 10½ in | 6 ft 1¾ in | 5 ft 7¼ in |
| 2-ply 2x10 | 11 ft 10½ in | 9 ft 8¼ in | 8 ft 4¾ in | 7 ft 6 in | 6 ft 10¼ in |
| 2-ply 2x12 | 13 ft 9¼ in | 11 ft 3 in | 9 ft 8¾ in | 8 ft 8½ in | 7 ft 11¼ in |
| 3-ply 2x10 | 14 ft 6½ in | 11 ft 10½ in | 10 ft 3¼ in | 9 ft 2¼ in | 8 ft 4¾ in |
| 3-ply 2x12 | 16 ft 10½ in | 13 ft 9¼ in | 11 ft 11 in | 10 ft 8 in | 9 ft 8¾ in |
| 4x8 | 10 ft 11 in | 8 ft 11 in | 7 ft 8¾ in | 6 ft 10¾ in | 6 ft 3¾ in |
| 4x10 | 13 ft 4¾ in | 10 ft 11¼ in | 9 ft 5½ in | 8 ft 5½ in | 7 ft 8¾ in |
| 4x12 | 15 ft 7¼ in | 12 ft 8¾ in | 11 ft ¼ in | 9 ft 10¼ in | 9 ft |
Doubling tributary width does not halve the span. Going from 4 ft to 8 ft cuts a 2-ply 2x12 from 13 ft 9¼ in to 9 ft 8¾ in, about 30%, because bending capacity drops with the square of span. That is why a quick span chart for a deck beam rarely transfers to a house girder.
A 4x12 beats a 2-ply 2x12 at every width here, 15 ft 7¼ in against 13 ft 9¼ in at 4 ft. It is ½ in wider, and the NDS size factor for 4 in thick, 12 in wide lumber is 1.1 against 1.0 for 2 in thick.
Roof Beam Span Chart With Snow Load
Roof beams reach farther than floor beams of the same size because snow is a two-month load. NDS Table 2.3.2 lets the allowed bending and shear stress rise by 15% (CD = 1.15), and roofs can use the looser L/240 sag limit from IRC Table R301.7 when no brittle ceiling hangs below.
This beam span chart for roof framing uses Douglas Fir-Larch No. 2 with a 30 psf snow load and a 15 psf dead load. Sag is held to L/240 under snow and L/180 under total load. Check your local ground snow load first, since many northern counties set 50 psf or more. Snow figures from any wood beam span calculator also assume an even load, which drifts against a taller wall are not.
| Roof beam (DF-L No. 2) | 4 ft tributary | 6 ft tributary | 8 ft tributary | 10 ft tributary | 12 ft tributary |
|---|---|---|---|---|---|
| 2-ply 2x8 | 10 ft 11¾ in | 8 ft 11½ in | 7 ft 9¼ in | 6 ft 11¼ in | 6 ft 4 in |
| 2-ply 2x10 | 13 ft 5 in | 10 ft 11½ in | 9 ft 5¾ in | 8 ft 5¾ in | 7 ft 9 in |
| 2-ply 2x12 | 15 ft 6¾ in | 12 ft 8½ in | 11 ft | 9 ft 10 in | 8 ft 11¾ in |
| 3-ply 2x10 | 16 ft 5¼ in | 13 ft 5 in | 11 ft 7½ in | 10 ft 4¾ in | 9 ft 5¾ in |
| 3-ply 2x12 | 19 ft ¾ in | 15 ft 6¾ in | 13 ft 5¾ in | 12 ft ¾ in | 11 ft |
| 4x8 | 12 ft 4¼ in | 10 ft 1 in | 8 ft 8¾ in | 7 ft 9¾ in | 7 ft 1½ in |
| 4x10 | 15 ft 1¾ in | 12 ft 4¼ in | 10 ft 8½ in | 9 ft 6¾ in | 8 ft 8¾ in |
| 4x12 | 17 ft 7½ in | 14 ft 4¾ in | 12 ft 5½ in | 11 ft 1¾ in | 10 ft 2 in |
A roof live load without snow is a seven-day load (CD = 1.25) in the NDS. Use that value only where snow never controls. Wind uplift and ridge-beam point loads from rafters are separate checks a roof beam span calculator does not replace.
4x8, 4x10 and 4x12 Beam Span by Species
A 4x8 beam spans about 10 to 11 ft at a light 200 plf load and about 7 to 8 ft at 400 plf. Species moves a wood beam span calculator result less than size does, because No. 2 grades of the common framing species fall within about 10% of each other.
| Size (No. 2) | Douglas Fir-Larch | Southern Pine | Hem-Fir | Spruce-Pine-Fir |
|---|---|---|---|---|
| 4x8 at 200 plf | 10 ft 11 in | 10 ft 2¼ in | 10 ft 2½ in | 10 ft 5¾ in |
| 4x8 at 400 plf | 7 ft 8¾ in | 7 ft 2½ in | 7 ft 6 in | 7 ft 7¼ in |
| 4x10 at 200 plf | 13 ft 4¾ in | 12 ft 1 in | 13 ft ¼ in | 13 ft 2½ in |
| 4x10 at 400 plf | 9 ft 5½ in | 8 ft 6½ in | 9 ft 2½ in | 9 ft 4 in |
| 4x12 at 200 plf | 15 ft 7¼ in | 14 ft 2¾ in | 15 ft 2 in | 15 ft 4½ in |
| 4x12 at 400 plf | 11 ft ¼ in | 10 ft ¾ in | 10 ft 8½ in | 10 ft 10½ in |
Southern Pine No. 2 trails here because its NDS Table 4B bending value for wide sizes is 800 psi at 10 in and 750 psi at 12 in. Older charts that still use the pre-2013 Southern Pine values of 1,150 psi or more overstate these spans by roughly 15 to 20%.
Spans assume dry lumber, a single 4x member, and a uniform load with sag held to L/360. Use the Lumber Weight Calculator to add the beam's own weight to the dead load on long 4x12 runs.
Load Capacity Chart in Pounds per Foot
A wood beam load capacity chart flips the question. It holds the span and gives the largest uniform load the beam can carry. The figures below are Douglas Fir-Larch No. 2, dry service, with sag held to L/360 under the full load.
| Beam (DF-L No. 2) | 8 ft span | 10 ft span | 12 ft span | 14 ft span | 16 ft span |
|---|---|---|---|---|---|
| 2-ply 2x8 | 296 plf | 189 plf | 131 plf | 82 plf | 55 plf |
| 2-ply 2x10 | 441 plf | 282 plf | 196 plf | 144 plf | 110 plf |
| 2-ply 2x12 | 593 plf | 380 plf | 264 plf | 194 plf | 148 plf |
| 3-ply 2x10 | 662 plf | 424 plf | 294 plf | 216 plf | 165 plf |
| 3-ply 2x12 | 890 plf | 570 plf | 396 plf | 291 plf | 222 plf |
| 4x8 | 374 plf | 239 plf | 152 plf | 96 plf | 64 plf |
| 4x10 | 562 plf | 359 plf | 250 plf | 183 plf | 134 plf |
| 4x12 | 761 plf | 487 plf | 338 plf | 249 plf | 190 plf |
To use a wood beam load calculator figure on site, multiply psf by tributary width. A floor at 50 psf with 8 ft of tributary width puts 400 plf on the beam, which only the 3-ply 2x10, 3-ply 2x12 and 4x12 carry at 10 ft. At 12 ft none of them do.
Capacity falls faster than span rises in every wood beam span calculator result. A 3-ply 2x12 carries 890 plf at 8 ft but only 222 plf at 16 ft, one quarter of the load for twice the span. That square law is the main reason posts or a mid-span girder cost less than oversized beams.
Beam Size for a 12-Foot Span
The lightest Douglas Fir-Larch No. 2 beam for a 12 ft span ranges from a 4x8 at 150 plf to a 3-ply 2x12 at 300 plf. At 400 plf no No. 2 sawn beam up to 3-ply 2x12 works, since its limit at 12 ft is 396 plf.
| Uniform load at 12 ft | Lightest beam that works | Built-up option |
|---|---|---|
| 150 plf | 4x8 | 2-ply 2x10 |
| 200 plf | 4x10 | 2-ply 2x12 |
| 300 plf | 4x12 | 3-ply 2x12 |
| 400 plf | None in No. 2 | 3-ply 2x12 in Select Structural |
Moving up a grade is often cheaper than moving up a size. A 3-ply 2x12 in Douglas Fir-Larch Select Structural carries 400 plf at 12 ft using 61% of its bending capacity, because its base bending value is 1,500 psi against 900 psi for No. 2.
The same 12 ft opening in a wall is a header, not a floor beam, and gets its loads from the roof and floors above. The Door Header Size Calculator covers those openings.
Heavy Timber Beam Chart for 6x and 8x Beams
Solid timbers 5 in and thicker carry their own grade values, separate from 2x and 4x dimension lumber. The chart uses Douglas Fir-Larch Beams and Stringers No. 1 values from the Western Lumber Grading Rules table published by Conrad Forest Products: Fb 1,350 psi, Fv 170 psi and E 1,600,000 psi.
| Timber (DF-L No. 1) | Dressed size | 400 plf | 600 plf | 800 plf |
|---|---|---|---|---|
| 6x10 | 5½ x 9½ in | 13 ft 3 in | 11 ft 1½ in | 9 ft 7¾ in |
| 6x12 | 5½ x 11½ in | 16 ft ½ in | 13 ft 5¾ in | 11 ft 8 in |
| 6x14 | 5½ x 13½ in | 18 ft 10 in | 15 ft 8½ in | 13 ft 7¼ in |
| 6x16 | 5½ x 15½ in | 21 ft 7½ in | 17 ft 11 in | 15 ft 6 in |
| 8x12 | 7½ x 11½ in | 17 ft 9½ in | 15 ft 6½ in | 13 ft 7½ in |
| 8x14 | 7½ x 13½ in | 20 ft 10½ in | 18 ft 2¾ in | 15 ft 10¾ in |
| 8x16 | 7½ x 15½ in | 23 ft 11¾ in | 20 ft 11 in | 18 ft 1¼ in |
Timbers deeper than 12 in lose a little bending value to the size factor (12 ÷ d) to the 1/9 power. That trims a 6x16 by 2.8%, small next to the gain from depth. Grade matters more here: a 6x12 in No. 2 (Fb 875 psi) spans 13 ft 3½ in at 400 plf against 16 ft ½ in for No. 1.
A solid 6x12 also beats a built-up 3-ply 2x12 of the same No. 2 grade, carrying 276 plf at 16 ft against 222 plf. Timbers are often sold green, so expect shrinkage and checking, and confirm the grade stamp matches the Beams and Stringers grade you designed for.
Spans of 20, 30 and 40 Feet
Dimension lumber runs out well before 20 ft, so no wood beam span calculator result for a 2x or 4x beam reaches that far at floor loads. A 3-ply 2x12 in Douglas Fir-Larch No. 2 carries only 142 plf at 20 ft, and Select Structural lifts that to just 188 plf.
Heavy timbers cover 20 ft. A Douglas Fir-Larch No. 1 8x16 carries 657 plf at 20 ft and 399 plf at 24 ft, and a 6x16 carries 482 plf at 20 ft. At 30 ft the 8x16 drops to 204 plf, held back by sag rather than strength.
The stiffness a long beam needs comes straight from the sag formula. Solving it for the required moment of inertia at L/360 gives the depth needed for a given width and E. Laminated veneer lumber is sold by E rating, so a 2.0E product uses 2,000,000 psi.
| Span at 400 plf | Required I at E 1.6M | Depth, 5¼ in wide, E 1.6M | Required I at E 2.0M | Depth, 5¼ in wide, E 2.0M |
|---|---|---|---|---|
| 20 ft | 1,350 in⁴ | 14.6 in | 1,080 in⁴ | 13.5 in |
| 30 ft | 4,556 in⁴ | 21.8 in | 3,645 in⁴ | 20.3 in |
| 40 ft | 10,800 in⁴ | 29.1 in | 8,640 in⁴ | 27.0 in |
These depths cover sag only. Bending and shear still need the Fb and Fv from the product data sheet, since LVL and glulam values vary by maker and layup. Entering those data-sheet values as a custom material runs all three checks on the same section.
A 40 ft span at floor loads needs a member over two feet deep, which also needs lateral bracing, a heavy connection at each end, and a large post or wall below. Treat any span past about 20 ft as engineered work rather than a lumber-yard selection.
Bending, Shear and Sag Formulas
Every wood beam span calculator result is the shortest of three spans, one per failure mode. For a simple span with a uniform load w in pounds per inch, each limit has a closed form.
Here Lb is the bending span, Fb′ the allowed bending stress in psi after NDS factors, and S the section modulus b × d² ÷ 6 in cubic inches.
Here Lv is the shear span, Fv′ the allowed shear stress in psi, and A the area b × d. It comes from the NDS shear stress of 1.5 × V ÷ A with V = wL ÷ 2 at each support.
Here Ld is the sag span, E′ the modulus of elasticity in psi, I the moment of inertia b × d³ ÷ 12, and n the limit denominator, such as 360 for L/360.
For a 2-ply 2x12 of Douglas Fir-Larch No. 2 at 200 plf (16.67 lb/in), S is 63.28 in³, A is 33.75 in² and I is 355.96 in⁴. The bending span is 13 ft 9¼ in, the shear span 40 ft 6 in and the sag span 16 ft 1¾ in, so bending sets the limit at 13 ft 9¼ in.
Two shortcuts in some online span tools change the answer. Using V ÷ A instead of 1.5 × V ÷ A understates shear stress by one third, and using 9½ in as the depth of a 2x10 overstates its stiffness, since the dressed depth is 9¼ in.
NDS Design Values and Adjustment Factors
Tabulated NDS values are base values. The allowed stress in a real beam is that base value times a stack of factors, and each one can move the span by several inches.
| Factor | Value | When it applies |
|---|---|---|
| Load duration, CD | 0.90 / 1.00 / 1.15 / 1.25 / 1.60 | Dead only / floor live / snow / roof live / wind or seismic |
| Wet service, CM | Fb 0.85, Fv 0.97, E 0.90 | Moisture over 19% in use; Fb stays 1.0 when Fb × CF ≤ 1,150 psi |
| Size, CF (2 in and 3 in thick) | 1.3 / 1.2 / 1.1 / 1.0 | 6 in / 8 in / 10 in / 12 in nominal width |
| Incising, Ci | Fb and Fv 0.80, E 0.95 | Lumber incised for preservative treatment |
| Repetitive member, Cr | 1.15 on Fb | 3 or more members, 24 in on center or less |
Wet service often costs less span than expected. A 2-ply 2x12 of Douglas Fir-Larch No. 2 at 200 plf keeps its 13 ft 9¼ in span when wet, since its Fb of 900 psi stays under the 1,150 psi cutoff and bending still governs over the 10% stiffness loss.
Southern Pine is the exception to the size-factor row. Its NDS Table 4B values are already set per width, so 2x8, 2x10 and 2x12 No. 2 carry 925, 800 and 750 psi with no further size factor. The base values come from the American Wood Council span calculator, which runs the 2018 NDS Supplement.
Bearing Length at Each Support
A beam that passes bending, shear and sag can still crush the wood where it sits on a post or wall. The seat length each end needs is the end reaction divided by the beam width times the species' compression value perpendicular to grain, Fc⊥.
Here lb is the bearing length in inches, R the end reaction in pounds and b the beam width. Fc⊥ drops by a third in wet service, and the load-duration factor does not raise it.
| Species (Fc⊥) | 2,000 lb reaction | 4,000 lb reaction | 6,000 lb reaction |
|---|---|---|---|
| Mixed Oak (800 psi) | 1½ in (IRC min) | 1¾ in | 2½ in |
| Douglas Fir-Larch (625 psi) | 1½ in (IRC min) | 2¼ in | 3¼ in |
| Southern Pine (565 psi) | 1½ in (IRC min) | 2⅜ in | 3⅝ in |
| Spruce-Pine-Fir (425 psi) | 1⅝ in | 3¼ in | 4¾ in |
| Hem-Fir (405 psi) | 1¾ in | 3⅜ in | 5 in |
| Western Woods (335 psi) | 2 in | 4 in | 6 in |
The table assumes a 3 in wide beam, such as a 2-ply 2x. A 6,000 lb reaction on Western Woods needs a full 6 in seat, more than a 4x4 post top offers, so either widen the bearing with a cap plate or pick a denser species.
IRC R502.6 sets the floor at 1½ in of bearing on wood or metal and 3 in on masonry or concrete, from IRC Chapter 5. Light beams usually land on that minimum: a 2-ply 2x12 Douglas Fir-Larch at 12 ft and 200 plf needs only 0.64 in by stress.
Spreadsheet, PDF and App Versions of the Math
A wood beam span calculator in Excel needs only three cells, one per span limit, and a MIN of the three. With Fb′ in B1, S in B2, Fv′ in B3, A in B4, E′ in B5, I in B6, w in lb/in in B7 and the limit denominator in B8, the span in inches is one formula.
The formula is =MIN(SQRT(8*B1*B2/B7), 4*B3*B4/(3*B7), POWER(384*B5*B6/(5*B7*B8),1/3)). Divide by 12 for feet. A printed PDF span table loses the adjustment factors, so record the species, grade, load and sag limit beside every number you keep.
A span app is only as good as the design values it loads. Confirm any Southern Pine result against NDS Table 4B before trusting it, since old values still circulate.
Answers on Wood Beam Span and Sizing
The answers below use the same Douglas Fir-Larch No. 2 values and IRC loads as the charts above unless a different species or grade is named.
How far can you span a wood beam?
A dimension-lumber beam spans about 5 to 17 ft at house floor loads, and a solid timber reaches about 24 ft. A 3-ply 2x12 of Douglas Fir-Larch No. 2 reaches 16 ft 10½ in with 4 ft of tributary width, while an 8x16 No. 1 timber spans 23 ft 11¾ in at 400 plf.
How to calculate the span of a beam?
Calculate the bending, shear and sag spans and take the shortest. For a 2-ply 2x12 Douglas Fir-Larch No. 2 at 200 plf those are 13 ft 9¼ in, 40 ft 6 in and 16 ft 1¾ in, so the beam spans 13 ft 9¼ in between supports.
What size wood beam will span 20 feet?
A 20 ft floor beam at 400 plf needs a heavy timber or engineered wood. A Douglas Fir-Larch No. 1 6x16 carries 482 plf at 20 ft and an 8x16 carries 657 plf, while a 3-ply 2x12 No. 2 holds just 142 plf. In 2.0E LVL, plan on about 13½ in of depth at 5¼ in wide.
How far can a 4x12 wood beam span?
A 4x12 of Douglas Fir-Larch No. 2 spans 15 ft 7¼ in at 200 plf and 11 ft ¼ in at 400 plf. In Southern Pine No. 2 those drop to 14 ft 2¾ in and 10 ft ¾ in, because its wide-size bending value is lower.
Can a wood beam span 30 feet?
A wood beam can span 30 ft at floor loads only as glulam or LVL. Stiffness alone needs about 20 to 22 in of depth at 5¼ in wide for 400 plf, while an 8x16 Douglas Fir-Larch No. 1 timber carries just 204 plf at 30 ft.
What beam can span 40 feet?
At 40 ft, a 400 plf beam needs about 27 to 29 in of depth at 5¼ in wide just to meet L/360. That is glulam, deep LVL, or a steel wide-flange, sized by an engineer along with its bearing, bracing and connections.
What size beam for 5 meter span?
For 5 m at 3 kN/m, a 3-ply 2x12 of Douglas Fir-Larch No. 2 works at 97% of its bending limit and spans up to 5.07 m. A 4x12 reaches only 4.69 m and a 2-ply 2x12 4.14 m at that load.
What is the span formula?
The span formula for a simply supported beam under uniform load is the smallest of √(8 × Fb′ × S ÷ w), 4 × Fv′ × A ÷ (3 × w) and the cube root of 384 × E′ × I ÷ (5 × w × n). Each term is the span where bending, shear or sag reaches its limit.
How to calculate beam formula?
For a simple span, moment is M = wL² ÷ 8, shear is V = wL ÷ 2 and midspan sag is 5wL⁴ ÷ (384 E I). A midspan point load P adds PL ÷ 4, P ÷ 2 and PL³ ÷ (48 E I). Divide M by S for bending stress and multiply V by 1.5 ÷ A for shear stress.
What is a wood beam span calculator?
A wood beam span calculator is a sizing aid that tests a sawn or engineered beam against the NDS limits for bending, shear and deflection. The result is the longest span, or the largest load, that keeps all three inside their limits for the species, grade, size and load chosen.
What determines the maximum span of a wood beam?
The load, the section depth, and the wood's bending strength and stiffness set the span, along with the sag limit. Depth counts most. Going from a 2-ply 2x10 to a 2-ply 2x12 raises S from 42.8 to 63.3 in³ and I from 198 to 356 in⁴, adding nearly 2 ft of span.
How do I use a wood beam calculator?
Gather the clear span, the load per foot or the tributary width with live and dead psf, and the species, grade and size printed on the lumber stamp. Pick the sag limit for the finish below, then check that bending, shear and sag all stay under 100% at your span.
What is wood beam span analysis?
Wood beam span analysis is the check of one beam under its real loads for each failure mode. A 2-ply 2x12 Douglas Fir-Larch No. 2 at 12 ft and 200 plf uses 76% of bending, 30% of shear and 41% of the L/360 sag limit, so bending controls it.
How do I find the span of a wood beam?
Measure between the faces of the supports and add half the bearing length at each end, as NDS 3.2.1 defines span. A beam bearing 1½ in on each post across a 12 ft clear opening has a design span of 12 ft 1½ in.
What is the deflection limit for a wood beam?
IRC Table R301.7 sets L/360 for floors and for ceilings with plaster or stucco, and L/240 for ceilings with gypsum board and all other members. Rafters over 3:12 with no ceiling attached allow L/180, and lintels under masonry veneer need L/600. On a 12 ft floor beam, L/360 is 0.40 in of sag.
How do I size a wood beam for a given load?
Convert the floor load to pounds per foot, then find the lightest section that passes all three checks. A 10 ft beam with 8 ft of tributary width at 50 psf carries 400 plf, and a 4x12 Douglas Fir-Larch No. 2 passes at 82% while a 2-ply 2x12 fails at 105%.
What size beam do I need for a 12-foot span?
A 12-foot span needs a 2-ply 2x12 or a 4x10 at 200 plf, and a 3-ply 2x12 or a 4x12 at 300 plf, in Douglas Fir-Larch No. 2. At 400 plf, step up to Select Structural or to LVL.
Can I use engineered lumber instead of solid sawn joists?
Engineered lumber can replace sawn joists and beams, sized from the maker's span tables or data sheet rather than NDS sawn values. IRC R502.7 also sends I-joists, LVL and glulam to the manufacturer's rules for lateral support, so blocking and hanger details change with the product.
When should I hire an engineer for a wood beam design?
Bring in an engineer for spans past about 20 ft, posts or bearing walls landing on the beam, cantilevers, continuous beams over three supports, notched or drilled beams, and any job where the permit office asks for stamped calculations. Those cases fall outside simple-span checks.
What is the modulus of elasticity of oak wood?
In the NDS Supplement, Mixed Oak dimension lumber has E of 1,100,000 psi in Select Structural and 900,000 psi in No. 2. Red Oak runs 1,400,000 and 1,200,000 psi, and White Oak matches Mixed Oak at 1,100,000 and 900,000 psi, well below Douglas Fir-Larch.
How do I determine the correct joist spacing for my project?
Joist spacing is the trade-off between joist size and span. Douglas Fir-Larch No. 2 at 16 in on center under a 40/10 psf floor spans 15 ft 7¼ in as a 2x10 and 18 ft 1 in as a 2x12. The Floor Joist Calculator covers spacing for a full floor.
What's the difference between Douglas Fir and Southern Pine for floor joists?
Douglas Fir-Larch No. 2 spans farther than Southern Pine No. 2 in wide sizes. A single 2x12 joist at 16 in on center reaches 18 ft 1 in in Douglas Fir and 16 ft 6 in in Southern Pine, because Southern Pine No. 2 2x12 has a bending value of 750 psi against 900 psi and E of 1.4 million against 1.6 million psi.
Is this calculator suitable for actual construction?
A wood beam span calculator is a planning check for simple spans with a braced top edge, uniform loads and an optional midspan point load. It checks bearing length but not lateral stability, notches or connections, so permit drawings still rely on code span tables, maker tables or an engineer's design.
What happens if my calculated span is close to the maximum allowable?
A span near the limit leaves no room for error in the load. A 2-ply 2x12 Douglas Fir-Larch No. 2 at 200 plf uses 76% of bending at 12 ft, 89% at 13 ft and 100% at 13¾ ft. A partition wall or a heavier finish added later pushes it past 100%.
What is the modulus of elasticity for common wood species?
No. 2 dimension lumber in the NDS Supplement runs from about 1.0 to 1.6 million psi. The table lists both Select Structural and No. 2 for the species most often used as beams.
| Species | E, Select Structural (psi) | E, No. 2 (psi) |
|---|---|---|
| Douglas Fir-Larch | 1,900,000 | 1,600,000 |
| Southern Pine | 1,800,000 | 1,400,000 |
| Hem-Fir | 1,600,000 | 1,300,000 |
| Spruce-Pine-Fir | 1,500,000 | 1,400,000 |
| Yellow Poplar | 1,500,000 | 1,300,000 |
| Douglas Fir-South | 1,400,000 | 1,200,000 |
| Eastern White Pine | 1,200,000 | 1,100,000 |
| Redwood | 1,100,000 | 1,000,000 |
| Western Cedars | 1,100,000 | 1,000,000 |
What is the difference between 2×10 and 2×12 for floor joists?
A 2x12 is 2 in deeper, which raises its moment of inertia by about 80% and its section modulus by about 48%. As Douglas Fir-Larch No. 2 joists at 16 in on center, that adds 2 ft 5¾ in of span, from 15 ft 7¼ in to 18 ft 1 in.
Why does deflection usually govern rather than bending strength?
Deflection governs less often than many expect. For No. 2 lumber at L/360 under house loads, bending usually controls, as with a 2x12 joist at 18 ft using 99% of bending and 74% of sag. Sag takes over with stiff limits, light loads or high grades, such as L/720 under stone, where a 2-ply 2x12 at 12 ft uses 82% of sag and 76% of bending.
Do I need blocking or bridging between floor joists?
IRC R502.7.1 requires blocking, bridging or a 1x3 strip nailed across the bottom at 8 ft or less only for joists deeper than a nominal 2x12. Under R502.7 every joist still needs lateral restraint at its ends, by full-depth blocking, a rim joist or a header.
How do I account for concentrated loads like bathtubs or heavy equipment?
Add the concentrated load as a point load on top of the uniform load. A 1,000 lb filled tub at the middle of a 12 ft, 2-ply 2x12 Douglas Fir-Larch No. 2 beam already carrying 200 plf raises bending use from 76% to 139%, and the safe span falls from 13 ft 9¼ in to 9 ft 7¾ in.
What does the repetitive member factor (Cr = 1.15) do?
Cr raises the allowed bending stress by 15% when three or more members sit 24 in on center or closer and share load through sheathing. A 3-ply 2x10 Douglas Fir-Larch No. 2 at 300 plf goes from an Fb′ of 990 psi and an 11 ft 10½ in span to 1,138 psi and 12 ft 8¾ in.
Can I use SPF #2 instead of Douglas Fir #2 to save money?
SPF No. 2 loses little span against Douglas Fir-Larch No. 2. A 2x12 joist at 16 in on center drops from 18 ft 1 in to 17 ft 10 in, and a 3-ply 2x12 beam at 400 plf from 11 ft 11 in to 11 ft 9 in. The bigger cost is bearing, since SPF's Fc⊥ of 425 psi needs 47% more seat length than Douglas Fir's 625 psi.
Count the boards and cost for any beam above with the Board Foot Calculator or the Lumber Calculator, and price the timber sizes by board foot before choosing them over built-up 2x.