LVL beam size calculator for the smallest 1 to 4 ply laminated veneer lumber beam on a span, checked for bending, shear, deflection and bearing, with span and load capacity tables.
Finds the smallest LVL beam, by wood volume, that passes bending, shear and deflection for your span and loads.
Grade, Plies and Deflection
Point Load at Midspan
LVL Price
LVL Beam Section Drawing
LVL Span Table for Your Load
| Depth | 1 Ply | 2 Plies | 3 Plies | 4 Plies |
|---|---|---|---|---|
| 5-1/2 in | 5.1 ft | 6.5 ft | 7.5 ft | 8.3 ft |
| 7-1/4 in | 6.5 ft | 8.6 ft | 9.9 ft | 10.9 ft |
| 9-1/4 in | 8.2 ft | 11.0 ft | 12.6 ft | 14.0 ft |
| 9-1/2 in | 8.4 ft | 11.3 ft | 13.0 ft | 14.3 ft |
| 11-1/4 in | 9.8 ft | 13.4 ft | 15.4 ft | 17.0 ft |
| 11-7/8 in | 10.4 ft | 14.1 ft | 16.2 ft | 17.9 ft |
| 14 in | 12.1 ft | 16.6 ft | 19.1 ft | 21.1 ft |
| 16 in | -- | 19.0 ft | 21.9 ft | 24.2 ft |
| 18 in | -- | 21.4 ft | 24.6 ft | 27.2 ft |
| 20 in | -- | 23.5 ft | 27.3 ft | 30.2 ft |
| 24 in | -- | 27.8 ft | 32.8 ft | 36.2 ft |
2-Ply 3-1/2 × 18 in Load Capacity Chart
| Span | Max Uniform Load | Governs |
|---|---|---|
| 8.0 ft | 4,770 plf | shear |
| 10.0 ft | 3,082 plf | bending |
| 12.0 ft | 2,135 plf | bending |
| 14.0 ft | 1,563 plf | bending |
| 16.0 ft | 1,193 plf | bending |
| 18.0 ft | 938 plf | bending |
| 20.0 ft | 757 plf | bending |
| 24.0 ft | 473 plf | deflection |
| 28.0 ft | 302 plf | deflection |
Step-by-Step LVL Beam Math
LVL Beam Size Calculator Example for a 20 Foot Floor Beam
A 20 ft floor beam carrying 12 ft of floor at 15 psf dead and 40 psf live needs a 2-ply 3-1/2 × 18 in LVL in 2.0E stock. Bending decides it at 88% of the adjusted strength, with sag at 83% of its limit.
Every LVL beam size calculator check starts by turning the floor into a line load. Here that is 180 plf dead, 18.4 plf of beam weight and 480 plf live, or 678 plf in all, on a simple span with joists bracing the top edge.
M is the maximum moment in lb-ft, w is the line load in plf, L is the span in feet and P is any point load at midspan in pounds. The 20 ft beam sees 678.4 × 20² ÷ 8 = 33,919 lb-ft.
Fb is the bending value at 12 in depth, CD is the load duration factor, (12/d)x is the depth factor, b is the width and d the depth in inches. A 2-ply 18 gives 2,600 × 1.0 × 0.9463 × 189 ÷ 12 = 38,753 lb-ft.
Δ is the midspan sag in inches, E is the modulus of elasticity, I is b d³ ÷ 12, G is the shear modulus, A is b × d and κ is 5/6. With E = 2.0 million psi and G = 125,000 psi, the live load sags the beam 0.55 in against L/360 = 0.67 in.
| Check | Demand | Allowed | Used |
|---|---|---|---|
| Bending | 33,919 lb-ft | 38,753 lb-ft | 88% |
| Shear at d from support | 5,766 lb | 11,970 lb | 48% |
| Live sag, L/360 | 0.55 in | 0.67 in | 83% |
| Total sag, L/240 | 0.78 in | 1.00 in | 78% |
In metric terms the LVL beam size calculator example is 89 × 457 mm over 6.1 m, carrying 9.63 kN/m of applied load and 46.0 kN·m of moment against 52.5 kN·m allowed.
The same span and load in steel works out to a W12×16, 6 in shallower and 48 lb lighter over 20 ft, on the Steel I-Beam Size Calculator.
Rule of Thumb Depths That Fail the Check
The span ÷ 24 rule gives 10 in of depth for a 20 ft beam, and every 9-1/4 to 9-1/2 in LVL fails the 12 ft floor load by more than five times. The rule has no load in it, so it cannot tell a deck beam from a girder.
| LVL at 20 ft, 12 ft of Floor | Capacity Used | Governs |
|---|---|---|
| 1-ply 1-3/4 × 9-1/2 in | 1,061% | Deflection |
| 2-ply 3-1/2 × 9-1/2 in | 531% | Deflection |
| 2-ply 3-1/2 × 11-7/8 in | 275% | Deflection |
| 2-ply 3-1/2 × 14 in | 170% | Deflection |
| 3-ply 5-1/4 × 14 in | 114% | Deflection |
| 2-ply 3-1/2 × 18 in | 88% | Bending |
In LVL beam size calculator terms, the common claim that an 18 ft span takes a single 1-3/4 × 11-7/8 in LVL holds only for light loads. Under 12 ft of floor, that one ply runs at 405% of capacity, and at 24 ft it reaches 941%.
Even a narrow 4 ft strip of floor over 20 ft needs a 2-ply 3-1/2 × 11-7/8 in at 92% used, deeper than the rule's 10 in. Tributary width moves the answer far more than span alone, so it is the first input in any LVL beam size calculator estimate.
Plies, Depth and Wood Volume Trade-Offs
For the 20 ft floor beam, the smallest LVL beam size calculator result by wood volume is the 2-ply 18 at 63 in² of section. A 3-ply 5-1/4 × 16 in or a 4-ply 7 × 14 in also passes, using 84 and 98 in², but each is shallower.
| Plies | Smallest That Passes | Section (in²) | Capacity Used | Governs | Weight for 20 ft |
|---|---|---|---|---|---|
| 1 | None up to 14 in | -- | -- | -- | -- |
| 2 | 3-1/2 × 18 in | 63 | 88% | Bending | 368 lb |
| 3 | 5-1/4 × 16 in | 84 | 77% | Deflection | 490 lb |
| 4 | 7 × 14 in | 98 | 85% | Deflection | 572 lb |
In an LVL beam size calculator search, ply count usually follows the wall. Two plies make 3-1/2 in, the width of a 2×4 wall, and three plies make 5-1/4 in for a 2×6 wall, so the beam sits flush with the framing below it.
Depth caps are the harder limit on an LVL beam size calculator answer. A beam flush with 9-1/2 or 11-7/8 in I-joists has no LVL answer at this load, 14 in needs the 4-ply, and switching to steel puts a 12 in W12×16 in the same floor depth.
This LVL beam size chart lists the smallest passing beam for common floor spans and tributary widths, all at 15 psf dead and 40 psf live with L/360 and L/240 limits.
| Span (ft) | 4 ft Tributary | 8 ft Tributary | 12 ft Tributary | 16 ft Tributary |
|---|---|---|---|---|
| 8 | 1-ply 7-1/4 | 1-ply 9-1/4 | 1-ply 9-1/4 | 1-ply 11-1/4 |
| 10 | 1-ply 9-1/4 | 1-ply 9-1/2 | 1-ply 11-7/8 | 1-ply 14 |
| 12 | 1-ply 9-1/4 | 1-ply 11-1/4 | 1-ply 14 | 2-ply 11-1/4 |
| 14 | 1-ply 11-1/4 | 1-ply 14 | 2-ply 11-7/8 | 2-ply 14 |
| 16 | 1-ply 11-7/8 | 2-ply 11-7/8 | 2-ply 14 | 2-ply 16 |
| 18 | 1-ply 14 | 2-ply 14 | 2-ply 16 | 2-ply 18 |
| 20 | 2-ply 11-7/8 | 2-ply 16 | 2-ply 18 | 2-ply 20 |
| 24 | 2-ply 14 | 2-ply 18 | 2-ply 24 | 2-ply 24 |
Depths are in inches, and LVL beam size calculator span tables like this one use plies 1-3/4 in (44 mm) wide. Typical LVL beam sizes run 5-1/2 to 24 in deep, and single plies stop at 14 in because deeper LVL goes in as two or more fastened plies.
Maximum Span Table by Depth and Ply Count
At 12 ft of floor and 15/40 psf, a 2-ply 11-7/8 in LVL spans 14.1 ft and a 2-ply 18 in spans 21.4 ft. Each value is the longest simple span in an LVL beam size calculator check where bending, shear and both sag limits still pass.
| Depth (in) | 1 Ply | 2 Plies | 3 Plies | 4 Plies |
|---|---|---|---|---|
| 5-1/2 | 5.1 ft | 6.5 ft | 7.5 ft | 8.3 ft |
| 7-1/4 | 6.5 ft | 8.6 ft | 9.9 ft | 10.9 ft |
| 9-1/4 | 8.2 ft | 11.0 ft | 12.6 ft | 14.0 ft |
| 9-1/2 | 8.4 ft | 11.3 ft | 13.0 ft | 14.3 ft |
| 11-1/4 | 9.8 ft | 13.4 ft | 15.4 ft | 17.0 ft |
| 11-7/8 | 10.4 ft | 14.1 ft | 16.2 ft | 17.9 ft |
| 14 | 12.1 ft | 16.6 ft | 19.1 ft | 21.1 ft |
| 16 | -- | 19.0 ft | 21.9 ft | 24.2 ft |
| 18 | -- | 21.4 ft | 24.6 ft | 27.2 ft |
| 20 | -- | 23.5 ft | 27.3 ft | 30.2 ft |
| 24 | -- | 27.8 ft | 32.8 ft | 36.2 ft |
A third ply adds about 15% of span and a fourth about 10% more, while each 2 in of extra depth adds 2.1 to 2.4 ft on a 2-ply. Depth buys span faster because stiffness grows with d³ and width only grows it in a straight line.
A 9-1/2 in LVL span chart changes most with the strip of floor it carries. In any LVL beam size calculator span search, the same 9-1/2 in beam reaches twice as far at 2 ft of floor as at 16 ft.
| LVL | 2 ft | 4 ft | 8 ft | 12 ft | 16 ft |
|---|---|---|---|---|---|
| 1-ply 9-1/2 | 16.5 ft | 13.0 ft | 10.2 ft | 8.4 ft | 7.3 ft |
| 2-ply 9-1/2 | 20.8 ft | 16.5 ft | 13.0 ft | 11.3 ft | 10.2 ft |
| 3-ply 9-1/2 | 23.6 ft | 18.9 ft | 14.9 ft | 13.0 ft | 11.8 ft |
| 1-ply 11-7/8 | 20.6 ft | 16.2 ft | 12.7 ft | 10.4 ft | 9.0 ft |
| 2-ply 11-7/8 | 25.9 ft | 20.6 ft | 16.2 ft | 14.1 ft | 12.7 ft |
| 3-ply 11-7/8 | 29.2 ft | 23.6 ft | 18.7 ft | 16.2 ft | 14.7 ft |
Column headings are tributary widths at 15 psf dead and 40 psf live. A 2 ft strip is close to a single joist or a stair stringer load, and 16 ft is a middle girder under two 16 ft joist bays.
Grades, Size Factor and Shear Deformation
On the 20 ft floor beam, all four LVL grades land on the same 2-ply 18 in LVL beam size calculator result, but at 76% to 90% used. A higher Fb only helps while bending governs, and the stiffer grades shift the limit to sag.
| Grade | Fb at 12 in (psi) | E in the Sag Check | Depth Factor | Allowable Moment, 2-ply 18 | Used, Governs |
|---|---|---|---|---|---|
| 2.0E | 2,600 | 2.0 million plus shear, G 125,000 | (12/d)0.136 | 38,753 lb-ft | 88%, bending |
| 2.1E | 3,100 | 2.0 million apparent | (12/d)1/9 | 46,674 lb-ft | 76%, deflection |
| 1.9E | 2,750 | 1.8 million apparent | (12/d)1/9 | 41,405 lb-ft | 85%, deflection |
| 1.8E column grade | 2,650 | 1.7 million apparent | (12/d)1/9 | 39,899 lb-ft | 90%, deflection |
In Boise's grades the name is the true, shear-free E. Boise Cascade's VERSA-LAM data lists 2.1E 3100 at a true E of 2.1 million and an apparent E of 2.0 million, which already folds shear sag into one number.
The 2.0E row keeps E at 2.0 million and adds shear sag as a separate term with G. Both routes land close together, and on this beam the shear term adds about 9% to the bending sag.
The 1.9E 2750 and 1.8E 2650 rows follow the APA product report for VERSA-LAM, and Boise sells the 1.8E as a column grade. Grade values differ between mills, so the sheet for the stock on site sets the LVL beam size calculator inputs.
LP's 1.9E sheet, for one, lists Fb 2,650 psi at 12 in and a steeper (12/d)1/7 above 12 in, which gives the 2-ply 18 39,389 lb-ft instead of 41,405.
| Depth (in) | (12/d)0.136 | (12/d)1/9 |
|---|---|---|
| 5-1/2 | 1.112 | 1.091 |
| 7-1/4 | 1.071 | 1.058 |
| 9-1/2 | 1.032 | 1.026 |
| 11-7/8 | 1.001 | 1.001 |
| 14 | 0.979 | 0.983 |
| 18 | 0.946 | 0.956 |
| 24 | 0.910 | 0.926 |
The depth factor raises shallow beams and cuts deep ones, since a deep beam has more volume where a flaw can start a break. A 24 in LVL loses 7 to 9% of its 12 in bending value before any other factor applies.
The Bending Stress Calculator works the bending side for one section in psi, which is the same Fb × CD × depth factor comparison in stress terms.
Stiffness Limits, Stone Tile and Load Duration
A natural stone floor at L/720 moves the 20 ft beam from a 2-ply 18 to a 2-ply 3-1/2 × 24 in, at 74% used. The TCNA Handbook sets L/360 for ceramic and porcelain tile and L/720 for stone.
| Live / Total Limit | Use | Live Sag Allowed at 20 ft | Smallest LVL | Governs |
|---|---|---|---|---|
| L/180 / L/120 | Roof, no ceiling | 1.33 in | 2-ply 3-1/2 × 18 | Bending |
| L/240 / L/180 | Roof | 1.00 in | 2-ply 3-1/2 × 18 | Bending |
| L/360 / L/240 | Floor, ceramic tile | 0.67 in | 2-ply 3-1/2 × 18 | Bending |
| L/720 / L/360 | Natural stone tile | 0.33 in | 2-ply 3-1/2 × 24 | Deflection |
Looser roof limits leave this LVL beam size calculator result unchanged, because bending already governs at L/360. Sag at 0.55 in sits well inside the roof allowance of 1.00 in, so the 18 in depth stays.
Load duration works the other way, raising wood strength for short loads. Snow gets CD = 1.15 and roof live load 1.25 under the NDS, while dead load alone gets 0.90, so the dead-only case belongs in every LVL beam size calculator run.
The same 678 plf treated as snow drops bending on the 2-ply 18 from 88% to 76%, and as roof live load to 70%. Sag is not adjusted, so the beam then runs on deflection at 83% and the size does not change.
The Beam Deflection Calculator breaks down sag for one known section, including loads that are not uniform.
Bracing and the Beam Stability Factor
Left unbraced over its full 20 ft, the 2-ply 3-1/2 × 18 in keeps only 69% of its braced bending strength and runs at 126%. The smallest LVL that passes becomes a 3-ply 5-1/4 × 16 in, at 77% used.
RB is the slenderness ratio, le is the effective length in inches, d the depth and b the width. For a uniform load with lu/d between 7 and 14.3, NDS 3.3.3 sets le = 1.63 lu + 3d, and RB may not pass 50.
CL is the beam stability factor and Fb here is the bending value times CD. The lesser of CL and the depth factor applies in LVL beam size calculator math, so short unbraced lengths often cost nothing.
| Unbraced Length (ft) | 2-Ply 18 in Strength Kept | Smallest LVL That Passes | Used, Governs |
|---|---|---|---|
| 0 (braced) | 100% | 2-ply 3-1/2 × 18 | 88%, bending |
| 6 | 100% | 2-ply 3-1/2 × 18 | 88%, bending |
| 8 | 99% | 2-ply 3-1/2 × 18 | 89%, bending |
| 10 | 95% | 2-ply 3-1/2 × 18 | 92%, bending |
| 15 | 82% | 2-ply 3-1/2 × 20 | 93%, bending |
| 20 | 69% | 3-ply 5-1/4 × 16 | 77%, deflection |
Width matters far more than depth once bracing is lost, because RB grows with depth but falls with the square of width. Over 20 ft unbraced, a 1-ply 14 in has RB 44.9 and CL 0.23, while a 3-ply 5-1/4 × 16 in has RB 16.0 and CL 0.95.
Joists hung from the side or sheathing nailed to the top edge count as bracing at their spacing. A beam that carries only a post or a wall with nothing tied to it needs the full span as lu in any LVL beam size calculator check.
The stability check uses Emin, the stiffness for buckling. The 2.0E sheet gives 1,016,535 psi, and the other grades here take the same share of their true E, so their Emin is derived rather than published.
Roof Headers and Ridge Beams Under Snow
A 2-ply LVL header over an 8 ft opening needs 7-1/4 in under 14 ft of roof at 30 psf snow and 15 psf dead. At 12 ft the 2-ply goes to 9-1/4 in, and at 16 ft it needs 14 in, all with CD = 1.15 and L/240 and L/180 limits.
| Opening (ft) | Roof Only, 2-Ply | Roof Only, 3-Ply | Roof + Floor, 2-Ply | Roof + Floor, 3-Ply |
|---|---|---|---|---|
| 4 | 5-1/2 in | 5-1/2 in | 5-1/2 in | 5-1/2 in |
| 6 | 5-1/2 in | 5-1/2 in | 7-1/4 in | 5-1/2 in |
| 8 | 7-1/4 in | 5-1/2 in | 9-1/4 in | 9-1/4 in |
| 10 | 9-1/4 in | 7-1/4 in | 11-1/4 in | 9-1/4 in |
| 12 | 9-1/4 in | 9-1/4 in | 14 in | 11-1/4 in |
| 14 | 11-1/4 in | 9-1/4 in | 16 in | 14 in |
| 16 | 14 in | 11-1/4 in | 20 in | 16 in |
The roof + floor columns add 12 ft of floor at 10 psf dead and 40 psf live, checked as a floor at CD = 1.0 with L/360 and L/240. That LVL header size chart shows a floor above costing one or two depth steps at the same opening.
A 3-ply header in a 2×6 wall saves a depth step at most openings in LVL beam size calculator runs. At 8 ft under roof only, 5-1/4 × 5-1/2 in passes where a 2-ply needs 7-1/4 in, which can free room for a taller window.
A structural ridge carries half the building width, measured flat. In an LVL ridge beam check with 30 psf snow, a 28 ft wide roof puts 14 ft on the ridge, and a 16 ft ridge span then needs a 2-ply 3-1/2 × 14 in at 74%.
| Ridge Span (ft) | 24 ft Wide Roof | 28 ft Wide Roof | 32 ft Wide Roof |
|---|---|---|---|
| 12 | 1-ply 11-7/8, 96% | 1-ply 14, 82% | 1-ply 14, 94% |
| 14 | 1-ply 14, 96% | 2-ply 11-1/4, 85% | 2-ply 11-1/4, 97% |
| 16 | 2-ply 11-1/4, 97% | 2-ply 14, 74% | 2-ply 14, 84% |
| 18 | 2-ply 14, 80% | 2-ply 14, 94% | 2-ply 16, 83% |
| 20 | 2-ply 14, 99% | 2-ply 16, 90% | 2-ply 18, 83% |
| 24 | 2-ply 18, 90% | 2-ply 20, 86% | 2-ply 20, 98% |
Bending governs every ridge in this table except the 16 ft span on a 24 ft roof. Snow loads vary by site, so the local ground snow figure, not the 30 psf used here, sets the real ridge size in an LVL beam size calculator check.
Capacity Chart in Pounds per Foot
A 2-ply 11-7/8 in LVL carries 979 plf at 12 ft and 240 plf at 20 ft, on top of its own weight. Each value uses the 27% dead and 73% live split of the floor example, with L/360 and L/240 limits.
| LVL | 8 ft | 10 ft | 12 ft | 14 ft | 16 ft | 18 ft | 20 ft | 24 ft |
|---|---|---|---|---|---|---|---|---|
| 1-ply 11-7/8 | 1,109 B | 708 B | 490 B | 337 D | 229 D | 163 D | 120 D | 70 D |
| 2-ply 9-1/2 | 1,462 B | 929 D | 553 D | 354 D | 240 D | 170 D | 124 D | 69 D |
| 2-ply 11-7/8 | 2,219 B | 1,416 B | 979 B | 673 D | 459 D | 326 D | 240 D | 140 D |
| 2-ply 14 | 3,018 B | 1,926 B | 1,333 B | 976 B | 736 D | 525 D | 387 D | 228 D |
| 3-ply 14 | 4,527 B | 2,890 B | 2,000 B | 1,464 B | 1,104 D | 788 D | 581 D | 341 D |
| 2-ply 16 | 3,873 B | 2,473 B | 1,712 B | 1,254 B | 956 B | 752 B | 570 D | 336 D |
| 2-ply 18 | 4,770 S | 3,082 B | 2,135 B | 1,563 B | 1,193 B | 938 B | 757 B | 473 D |
In this LVL beam size calculator chart, B means bending governs, D deflection and S shear, all in 2.0E stock at floor load duration. Deeper beams hold on to bending control to longer spans, so the 2-ply 18 stays bending-governed out to 20 ft.
A 3-ply 14 carries 1.5 times the 2-ply 14 at every span, since width scales strength and stiffness in a straight line. That makes an LVL beam load capacity chart for one ply count easy to scale to another.
Shear Near Supports, Bearing and Point Loads
Shear in the 20 ft LVL beam size calculator example is checked one beam depth in from each support, which cuts the design shear by 15%, from 6,784 to 5,766 lb. Under the NDS, uniform load within that distance may be left out of the shear check.
Va is the allowable shear with Fv = 285 psi, lb is the bearing length in inches, R is the end reaction and Fc⊥ = 750 psi is the bearing value. Both values match the VERSA-LAM and LP sheets.
The 2-ply 18 pushes 6,784 lb into each support, so it needs 6,784 ÷ (750 × 3.5) = 2.58 in of bearing. A post or wall plate narrower than that crushes the LVL, and the post's own footing goes through the Bearing Pressure Calculator.
A post carrying 3,000 lb dead and 4,000 lb live at midspan moves the 20 ft LVL beam size calculator result from a 2-ply 18 to a 3-ply 5-1/4 × 20 in at 98%, with bending at 69,531 lb-ft against 70,744 lb-ft allowed.
The same post on a 12 ft span is carried by the 2-ply 18 at 86%. Posts away from midspan change the moment, and the Beam Load Calculator finds the reactions for any position.
Board Feet, Weight per Foot and Price
A 2-ply 3-1/2 × 18 in LVL is 5.25 board feet per foot, or 105 board feet over 20 ft. At $5 per board foot that is $525, and the beam weighs 368 lb, or 167 kg, before any hangers or fasteners.
| Depth (in) | 1 Ply (lb/ft) | 2 Plies (lb/ft) | 3 Plies (lb/ft) | 4 Plies (lb/ft) | 1 Ply (kg/m) |
|---|---|---|---|---|---|
| 7-1/4 | 3.7 | 7.4 | 11.1 | 14.8 | 5.5 |
| 9-1/2 | 4.8 | 9.7 | 14.5 | 19.4 | 7.2 |
| 11-7/8 | 6.1 | 12.1 | 18.2 | 24.2 | 9.0 |
| 14 | 7.1 | 14.3 | 21.4 | 28.6 | 10.6 |
| 16 | 8.2 | 16.3 | 24.5 | 32.7 | 12.2 |
| 18 | 9.2 | 18.4 | 27.6 | 36.8 | 13.7 |
| 24 | 12.2 | 24.5 | 36.8 | 49.0 | 18.2 |
This LVL beam weight chart uses 42 lb/ft³, which matches the mills closely. LP lists 5.9 lb/ft for a 1-3/4 × 11-7/8 in and 9.0 for 1-3/4 × 18 in, and Boise lists 7.1 lb/ft for 1-3/4 × 14 in.
For an LVL weight conversion chart in metric, multiply lb/ft by 1.488 for kg/m. One 1-3/4 in ply of 11-7/8 in LVL is 9.0 kg/m, so a 6 m length weighs about 54 kg.
For an LVL beam size calculator price, board feet are width × depth × length in feet ÷ 12, with width and depth in inches.
A 1-ply 11-7/8 is 1.73 board feet per foot, a 2-ply 14 is 4.08 and a 3-ply 14 is 6.13, so LVL priced per board foot costs in step with wood volume.
Choosing and Spanning an LVL Beam
These LVL beam size calculator answers use 2.0E LVL at floor load duration with L/360 and L/240 limits and a top edge braced by joists. Spans are simple spans between supports, and loads include the beam's own weight.
What is LVL beam size calculator?
The term means a sizing check for the smallest laminated veneer lumber beam that passes bending, shear and sag at one span and load. For a 20 ft floor beam under 12 ft of floor at 15/40 psf, the smallest is a 2-ply 3-1/2 × 18 in.
What is an LVL span calculator?
Span checking runs the sizing math the other way: for a given LVL, the answer is the longest span that still passes. A 2-ply 11-7/8 in under 12 ft of floor reaches 14.1 ft, and a 2-ply 14 in reaches 16.6 ft.
How do you calculate maximum span for an LVL beam?
Solve each check for the span and keep the shortest one. For a 2-ply 11-7/8 in with 480 plf of live load, the L/360 sag limit alone gives L³ = 384 E I ÷ (5 × 360 × w), or 14.4 ft with w = 40 lb/in (480 plf), E = 2.0 million psi and I = 488 in⁴.
Adding shear sag trims that to 14.1 ft, and bending and shear allow more, so deflection sets the span. A heavier load or a stiffer limit such as L/720 shortens it again.
How do I choose a LVL beam?
Start from the span, the tributary width and the floor or roof loads, then choose the ply count from the wall width and the depth from the headroom. Run an LVL beam size calculator check, and step up a depth or a ply until every result is under 100%.
Then match the grade on the mill's sheet, confirm bearing length at each end, and fasten the plies to the maker's nailing or bolting schedule. For the 20 ft floor beam that means 2.58 in of bearing under a 2-ply 18.