Retaining Wall Cost Calculator

Updated

Retaining wall cost calculator for block, timber and concrete walls that turns length and height into blocks with the buried course, caps, gravel tons, pipe, labor and cost per ft.

Wall Size and Material

Measure the wall length and the height showing above ground. Buried courses and gravel are added for you.

%
Block, Timber or Concrete Size16 in × 6 in, capped
Gravel, Drainage and Geogrid12 in drainage gravel
layers
Prices and Labor$15.00/sq ft labor
$/block
$/cap
$/timber
Retaining Wall Cost
$2,685 Total Wall Cost
$89.49 per linear ft and $29.83 per sq ft of wall face
152 Wall Blocks
Cap Blocks25
Courses Incl. Buried7
Courses fill the exposed height plus the buried depth. With a cap row, the top course is caps instead of blocks.
6.75 tons Gravel
Drainage Backfill3.89 cu yd
Leveling Base Pad1.11 cu yd
Gravel weight uses 100 lb per cubic foot of crushed stone. Backfill runs the full built height behind the wall at your width.
$1,335 Materials
Blocks and Caps$986.00
Gravel and Drain Pipe$348.75
Materials include the wall units with waste, all gravel, the perforated drain pipe and any geogrid layers you enter.
90 sq ft Wall Face
Labor Cost$1,350.00
Trench Dig2.22 cu yd
Face area is length times exposed height and sets labor. The trench is dug to the bottom of the pad or footing.
Wall Cross-Section4 ft footing to top
Grade3 ft exposed6 in buried12 in gravel
Cost Breakdown$2,685
ItemCostPer ftShare
Blocks and Caps$986.00$32.8736.7%
Gravel$303.75$10.1311.3%
Drain pipe$45.00$1.501.7%
Labor$1,350.00$45.0050.3%
Total$2,684.75$89.49100%
Cost by Wall Length and HeightYour material and prices
Length × HeightFaceTotal CostPer ft
10 × 3 ft30 sq ft$912$91.18
20 × 3 ft60 sq ft$1,779$88.95
30 × 3 ft90 sq ft$2,685$89.49
50 × 3 ft150 sq ft$4,464$89.28
100 × 3 ft300 sq ft$8,883$88.83
30 × 2 ft60 sq ft$1,892$63.08
30 × 4 ft120 sq ft$3,483$116.09
30 × 5 ft150 sq ft$4,275$142.51
30 × 6 ft180 sq ft$5,073$169.11
Step-by-Step Wall Cost Math16 steps
Wall face30 ft × 3 ft = 90 sq ft
Built height36 in + 6 in buried = 42 in
Footing to top42 in + 6 in base pad = 48 in = 4 ft
Courses42 in ÷ 6 in = 7, rounded up to 7, minus 1 cap row = 6
Blocks per course360 in ÷ 16 in = 22.5, rounded up to 23
Wall blocks6 × 23 × 1.1 = 151.8, rounded up to 152
Cap blocks360 in ÷ 16 in × 1.1 = 24.75, rounded up to 25
Block cost152 × $5.50 + 25 × $6.00 = $986.00
Drainage backfill30 ft × 3.5 ft × 1 ft = 105 cu ft
Base pad30 ft × 2 ft × 0.5 ft = 30 cu ft
Gravel weight135 cu ft × 100 lb = 13,500 lb = 6.75 tons
Gravel cost6.75 tons × $45.00 = $303.75
Drain pipe30 ft × $1.50 = $45.00
Labor90 sq ft × $15.00 = $1,350.00
Trench dig30 ft × 2 ft × 1 ft = 60 cu ft = 2.2222 cu yd
Total$1,334.75 materials + $1,350.00 labor = $2,684.75
Right at the 4 ft Permit Limit
Footing to top is 4 ft, the tallest most codes allow without a permit, and only when the wall holds back no surcharge such as a slope or driveway.

Itemized Retaining Wall Cost Calculator Estimate for a 30 × 3 ft Wall

A segmental block wall 30 ft long and 3 ft high comes to about $2,685, or $89.49 per linear foot and $29.83 per sq ft of wall face. That uses sample prices of $5.50 per block, $6 per cap, $45 per ton of gravel and $15 per sq ft of labor.

Line ItemQuantityCost
Wall blocks, 16 × 6 in152$836
Cap blocks25$150
Gravel, drainage and base pad135 cu ft, 6.75 tons$303.75
Perforated drain pipe30 ft at $1.50$45
Labor90 sq ft at $15$1,350
Total30 ft × 3 ft$2,684.75

Every price above is a sample, not a market quote. A retaining wall cost calculator estimate depends on local block, gravel and labor rates, so price each line with a supplier and a wall contractor before comparing totals.

Labor is half of this retaining wall cost calculator total at these rates, $1,350 of $2,685. Materials split into blocks at $986, gravel at $303.75 and pipe at $45, so the drainage system costs about a third as much as the blocks it protects.

In metric terms the same wall is 9.14 m long and 8.36 m² of face, which works out to about $293.61 per linear meter and $321.09 per m². Retaining wall cost per m2 quotes convert from per-square-foot figures by multiplying by 10.76.

Blocks Below Grade and the Cap Row

In a retaining wall cost calculator count, a 3 ft wall is 3 1/2 ft of block, because the first course sits 6 in below the ground. With 6 in tall blocks that is 7 courses, 6 of wall block and 1 of caps, not the 6 courses that exposed height alone suggests.

N is the wall block count, H is the exposed height in feet, e is the buried depth in inches, hb and lb are block height and length in inches, L is wall length in feet and w is waste.

The c is 1 with a cap row and 0 without, since caps replace the top course of wall blocks and are counted by length instead.

For the 30 ft retaining wall cost calculator example, 42 in of total height ÷ 6 in = 7 courses, less 1 for the cap row, leaves 6. Each course takes 360 ÷ 16 = 22.5 blocks, rounded to 23, so 6 × 23 × 1.1 = 151.8 rounds up to 152 wall blocks.

Allan Block's embedment guide sets 6 in of buried block as the minimum on flat ground, plus 1 in for each foot of height above 6 ft. A slope below the wall needs far more, enough to leave a 5 ft level bench in front.

Caps in a retaining wall cost calculator estimate are counted along the length, not the height. At 16 in per cap, 30 ft takes 22.5 caps, and 10% waste makes 25.

A retaining wall cost calculator block count without the buried course runs one full course short, 23 blocks on this wall before waste.

The Retaining Wall Calculator handles block, row and capstone counts on their own, and the Retaining Wall Slope Calculator works out the batter and setback each course adds.

Wall Length: 10, 20, 30, 50 and 100 ft Costs

A 3 ft block wall costs about $912 at 10 ft long, $1,779 at 20 ft, $2,685 at 30 ft and $8,883 at 100 ft. Per foot the retaining wall cost calculator price barely moves, about $89 to $91, because almost every line scales with length.

Length2 ft High3 ft High4 ft High3 ft Blocks + Caps3 ft Gravel
10 ft$646$912$1,18353 + 92.25 tons
20 ft$1,253$1,779$2,30699 + 174.5 tons
30 ft$1,892$2,685$3,483152 + 256.75 tons
50 ft$3,145$4,464$5,788251 + 4211.25 tons
100 ft$6,251$8,883$11,516495 + 8322.5 tons

The retaining wall cost calculator totals use the same sample prices, 6 in of buried block, 12 in of drainage gravel and a 24 × 6 in base pad. Short walls cost a little more per foot because a partial block in each course rounds up to a whole one.

A 10 ft wall needs 53 wall blocks at 3 ft high, 5.3 per foot of wall, while the 100 ft wall needs 4.95 per foot. That rounding is the only reason a retaining wall cost per foot figure shifts with length at all.

A wall 10 ft tall is a different retaining wall cost calculator project from one 10 ft long. At that height the wall needs an engineered design, a permit and usually geogrid, so a materials-and-labor estimate covers only part of its real cost.

Height Drives Cost Faster Than Length

Each added foot of height on a 30 ft wall adds about $800 before any engineering, which starts to apply once the wall passes 4 ft. In retaining wall cost calculator terms, a 2 ft wall runs $63 per foot, a 4 ft wall $116 and a 6 ft wall $169.

Exposed HeightCourses Incl. BuriedWall BlocksGravelTotal, 30 ftPer Linear ftHeight From Footing
2 ft51025.25 tons$1,892$63.083 ft
3 ft71526.75 tons$2,685$89.494 ft
4 ft92038.25 tons$3,483$116.095 ft
5 ft112539.75 tons$4,275$142.516 ft
6 ft1330411.25 tons$5,073$169.117 ft

Per square foot of face, taller walls look slightly cheaper, $31.54 at 2 ft against $28.18 at 6 ft, because the buried course and base pad spread over more area.

That trend reverses once engineering, geogrid and permits join a retaining wall installation cost estimate.

Above 4 ft, Allan Block's installation guide requires a drain pipe on gravity walls and deepens the base from 4 in to 6 in.

Reinforced walls add geogrid, priced by area as layers × wall length × the length each layer runs into the soil. Three engineer-specified layers running 4 ft back on a 50 ft wall are 600 sq ft, or 66.67 sq yd, about $133 at a sample $2 per sq yd.

The grid itself is cheap next to a 50 × 5 ft wall that costs about $7,107 before it. The real geogrid cost is the extra digging and compacted backfill over that 4 ft depth, plus the engineer who sets the layer count.

Gravel Tons for Drainage and the Leveling Pad

The 30 × 3 ft retaining wall cost calculator example takes 135 cu ft of gravel, 5 cu yd or about 6.75 tons. Of that, 105 cu ft fills a 12 in drainage zone behind the wall and 30 cu ft forms the 24 × 6 in leveling pad.

In retaining wall cost calculator math, G is gravel in cubic feet, b is the drainage zone width in inches, wp and dp are the base pad width and depth in inches, and L, H and e are length, exposed height and buried depth as before.

Allan Block calls for 12 in of wall rock behind the block and a base trench 24 in wide with at least 6 in of compacted base. For walls under 4 ft it allows an 18 in trench and a 4 in base, which trims the pad on the example wall from 30 cu ft to 15.

Gravel weight in a retaining wall cost calculator order depends on which gravel the yard sells. Rockland's weights table lists crushed stone at 2,700 lb per cu yd and loose dry gravel at 2,565, so the 5 cu yd order weighs 6.41 to 6.75 tons.

A gravel density of 84 lb per cu ft, sometimes used in quick estimates, puts the same order at 5.67 tons, 16% light. Ordering by that figure leaves the drainage zone about a ton short on a 30 ft wall.

The trench is its own dig. For block it runs as wide as the 24 in pad and as deep as the buried course plus the pad, 12 in, so the 30 ft wall removes 60 cu ft, about 2.22 cu yd of soil before swell.

A poured wall digs to the bottom of its 24 × 12 in footing, 18 in below grade with 6 in of buried stem, which is 90 cu ft or 3.33 cu yd on the same 30 ft run.

Drain pipe runs at the lowest point behind the wall, vented to daylight at least every 50 ft per Allan Block. On a 100 ft wall that means at least two outlets, so plan where the water will discharge before the base is dug.

Segmental Block, 6x6 Timber or Poured Concrete

At the sample prices, a 50 ft wall 4 ft high costs about $5,788 in segmental block, $5,850 in 6x6 timbers and $5,211 in poured concrete. The retaining wall cost calculator gap between materials is far smaller than the gap between a 3 ft and a 4 ft wall.

Material, 50 × 4 ftUnitsUnit CostGravelTotalPer sq ft
Block at $5.50, caps at $6335 blocks + 42 caps$2,094.5013.75 tons$5,788$28.94
6x6 timber at $28 per 8 ft77 timbers$2,15613.75 tons$5,850$29.25
Concrete at $160 per cu yd10.19 cu yd$1,629.6311.25 tons$5,211$26.05

For a timber retaining wall cost calculator count, a 6x6 timber is 5 1/2 in thick, so a 4 ft wall with 6 in buried needs 10 courses of timber against 9 of 6 in block.

At $28 per 8 ft timber the wood costs $61.50 more than block on this wall, so timber saves money only where it sells for less locally.

Poured concrete looks cheapest on materials, but the figure covers only an 8 in stem and a 24 × 12 in footing. Forms, rebar and the pump or chute are extra, and a concrete retaining wall cost calculator figure should add them before comparing.

The Concrete Footing Calculator sizes the footing volume, and the Rebar Calculator works out bar count and weight for a poured stem.

Permit Height Is Measured From the Footing

Under IRC Section R105.2, a retaining wall up to 4 ft tall is permit-exempt, but that height runs from the bottom of the footing to the top of the wall. A 3 ft exposed wall on 6 in of buried block and a 6 in pad is already 4 ft by that measure.

The exemption, quoted in Port Townsend's IRC 2018 retaining wall handout, also ends whenever the wall supports a surcharge. A slope above the wall, a driveway, parking or a building nearby all count.

Exposed HeightPlus 6 in Buried and 6 in PadPlus 6 in Buried and 12 in FootingPermit-Exempt Under R105.2
2.5 ft3.5 ft4 ftYes, with no surcharge
3 ft4 ft4.5 ftOn a 6 in pad, with no surcharge
3.5 ft4.5 ft5 ftNo
4 ft5 ft5.5 ftNo

A homeowner who stops at a 4 ft exposed height to skip the permit has usually built a 5 ft wall in code terms, which a retaining wall cost calculator plan should catch early.

Local rules can be stricter, so a quick call to the building department belongs in any retaining wall cost estimator budget.

Retaining Wall Planning Answers

Two questions remain once size and material are settled. Both answers use the same block size, gravel and retaining wall cost calculator sample prices as the tables.

Why do you need a retaining wall calculator?

A retaining wall cost calculator count matters because a wall hides much of its material below ground and behind itself, so eyeballing the exposed face undercounts.

On the 30 × 3 ft example, the buried course adds 23 blocks and the gravel behind and under the wall adds 6.75 tons.

Those hidden lines are where a short order hurts most. Running out of gravel stops backfill mid-wall, and the last course or caps can come from a different color lot if the first order falls short.

Does a 2 foot retaining wall need a footing?

A 2 ft segmental block wall needs a compacted gravel base, not a concrete footing. Allan Block allows an 18 in wide trench with at least 4 in of compacted base for walls under 4 ft, plus 6 in of buried block.

A 2 ft wall 30 ft long uses 5.25 tons of gravel and 102 wall blocks at the 24 × 6 in pad. Poured concrete walls are the exception, since their stem needs a concrete footing, 24 × 12 in in the concrete estimate above.