Sheet metal gauge calculator for gauge to inch and mm across 7 gauge standards, a caliper reading back to its closest gauge, sheet weight per sq ft or m², and the nearest fraction.
Pick the metal and gauge; each metal uses its own gauge standard.
Same Gauge Across Metals Diagram
Sheet Metal Gauge Chart, All Metals
| Gauge | Steel | Galvanized | Stainless | Aluminum | Brass | Copper | SWG |
|---|---|---|---|---|---|---|---|
| 3 | 0.2391 | - | 0.2500 | 0.2294 | 0.2294 | 0.2590 | 0.2520 |
| 4 | 0.2242 | - | 0.2344 | 0.2043 | 0.2043 | 0.2380 | 0.2320 |
| 5 | 0.2092 | - | 0.2187 | 0.1819 | 0.1819 | 0.2200 | 0.2120 |
| 6 | 0.1943 | - | 0.2031 | 0.1620 | 0.1620 | 0.2030 | 0.1920 |
| 7 | 0.1793 | - | 0.1875 | 0.1443 | 0.1443 | 0.1800 | 0.1760 |
| 8 | 0.1644 | 0.1681 | 0.1719 | 0.1285 | 0.1285 | 0.1650 | 0.1600 |
| 9 | 0.1495 | 0.1532 | 0.1562 | 0.1144 | 0.1144 | 0.1480 | 0.1440 |
| 10 | 0.1345 | 0.1382 | 0.1406 | 0.1019 | 0.1019 | 0.1340 | 0.1280 |
| 11 | 0.1196 | 0.1233 | 0.1250 | 0.0907 | 0.0907 | 0.1200 | 0.1160 |
| 12 | 0.1046 | 0.1084 | 0.1094 | 0.0808 | 0.0808 | 0.1090 | 0.1040 |
| 13 | 0.0897 | 0.0934 | 0.0937 | 0.0720 | 0.0720 | 0.0950 | 0.0920 |
| 14 | 0.0747 | 0.0785 | 0.0781 | 0.0641 | 0.0641 | 0.0830 | 0.0800 |
| 15 | 0.0673 | 0.0710 | 0.0703 | 0.0571 | 0.0571 | 0.0720 | 0.0720 |
| 16 | 0.0598 | 0.0635 | 0.0625 | 0.0508 | 0.0508 | 0.0650 | 0.0640 |
| 17 | 0.0538 | 0.0575 | 0.0562 | 0.0453 | 0.0453 | 0.0580 | 0.0560 |
| 18 | 0.0478 | 0.0516 | 0.0500 | 0.0403 | 0.0403 | 0.0490 | 0.0480 |
| 19 | 0.0418 | 0.0456 | 0.0437 | 0.0359 | 0.0359 | 0.0420 | 0.0400 |
| 20 | 0.0359 | 0.0396 | 0.0375 | 0.0320 | 0.0320 | 0.0350 | 0.0360 |
| 21 | 0.0329 | 0.0366 | 0.0344 | 0.0285 | 0.0285 | 0.0320 | 0.0320 |
| 22 | 0.0299 | 0.0336 | 0.0312 | 0.0253 | 0.0253 | 0.0280 | 0.0280 |
| 23 | 0.0269 | 0.0306 | 0.0281 | 0.0226 | 0.0226 | 0.0250 | 0.0240 |
| 24 | 0.0239 | 0.0276 | 0.0250 | 0.0201 | 0.0201 | 0.0220 | 0.0220 |
| 25 | 0.0209 | 0.0247 | 0.0219 | 0.0179 | 0.0179 | 0.0200 | 0.0200 |
| 26 | 0.0179 | 0.0217 | 0.0187 | 0.0159 | 0.0159 | 0.0180 | 0.0180 |
| 27 | 0.0164 | 0.0202 | 0.0172 | 0.0142 | 0.0142 | 0.0160 | 0.0164 |
| 28 | 0.0149 | 0.0187 | 0.0156 | 0.0126 | 0.0126 | 0.0140 | 0.0148 |
| 29 | 0.0135 | 0.0172 | 0.0141 | 0.0113 | 0.0113 | 0.0130 | 0.0136 |
| 30 | 0.0120 | 0.0157 | 0.0125 | 0.0100 | 0.0100 | 0.0120 | 0.0124 |
Mild Steel Gauge Weight Chart
| Gauge | Thickness | Weight per Sq Ft | Per 4 × 8 ft Sheet |
|---|---|---|---|
| 3 Ga | 0.2391 in | 9.999 lb | 320.0 lb |
| 4 Ga | 0.2242 in | 9.376 lb | 300.0 lb |
| 5 Ga | 0.2092 in | 8.749 lb | 280.0 lb |
| 6 Ga | 0.1943 in | 8.126 lb | 260.0 lb |
| 7 Ga | 0.1793 in | 7.498 lb | 239.9 lb |
| 8 Ga | 0.1644 in | 6.875 lb | 220.0 lb |
| 9 Ga | 0.1495 in | 6.252 lb | 200.1 lb |
| 10 Ga | 0.1345 in | 5.625 lb | 180.0 lb |
| 11 Ga | 0.1196 in | 5.002 lb | 160.1 lb |
| 12 Ga | 0.1046 in | 4.374 lb | 140.0 lb |
| 13 Ga | 0.0897 in | 3.751 lb | 120.0 lb |
| 14 Ga | 0.0747 in | 3.124 lb | 100.0 lb |
| 15 Ga | 0.0673 in | 2.814 lb | 90.1 lb |
| 16 Ga | 0.0598 in | 2.501 lb | 80.0 lb |
| 17 Ga | 0.0538 in | 2.250 lb | 72.0 lb |
| 18 Ga | 0.0478 in | 1.999 lb | 64.0 lb |
| 19 Ga | 0.0418 in | 1.748 lb | 55.9 lb |
| 20 Ga | 0.0359 in | 1.501 lb | 48.0 lb |
| 21 Ga | 0.0329 in | 1.376 lb | 44.0 lb |
| 22 Ga | 0.0299 in | 1.250 lb | 40.0 lb |
| 23 Ga | 0.0269 in | 1.125 lb | 36.0 lb |
| 24 Ga | 0.0239 in | 0.999 lb | 32.0 lb |
| 25 Ga | 0.0209 in | 0.874 lb | 28.0 lb |
| 26 Ga | 0.0179 in | 0.749 lb | 24.0 lb |
| 27 Ga | 0.0164 in | 0.686 lb | 21.9 lb |
| 28 Ga | 0.0149 in | 0.623 lb | 19.9 lb |
| 29 Ga | 0.0135 in | 0.565 lb | 18.1 lb |
| 30 Ga | 0.0120 in | 0.502 lb | 16.1 lb |
Step-by-Step Gauge Math
Gauge to mm With a Sheet Metal Gauge Calculator
16 gauge mild steel is 0.0598 in, or 1.519 mm, thick. 18 gauge is 0.0478 in (1.214 mm), 14 gauge is 0.0747 in (1.897 mm) and 10 gauge is 0.1345 in (3.416 mm).
Those are Manufacturers' Standard Gauge values for uncoated carbon steel, the scale behind every steel sheet metal gauge calculator result. The same numbers appear on the Metal Supermarkets gauge chart and in mill price lists.
| Gauge | Inches | mm | Drop From the Gauge Before |
|---|---|---|---|
| 7 | 0.1793 | 4.554 | 0.0150 in |
| 8 | 0.1644 | 4.176 | 0.0149 in |
| 10 | 0.1345 | 3.416 | 0.0150 in |
| 11 | 0.1196 | 3.038 | 0.0149 in |
| 12 | 0.1046 | 2.657 | 0.0150 in |
| 14 | 0.0747 | 1.897 | 0.0150 in |
| 16 | 0.0598 | 1.519 | 0.0075 in |
| 18 | 0.0478 | 1.214 | 0.0060 in |
| 20 | 0.0359 | 0.912 | 0.0059 in |
| 22 | 0.0299 | 0.759 | 0.0030 in |
| 24 | 0.0239 | 0.607 | 0.0030 in |
| 26 | 0.0179 | 0.455 | 0.0030 in |
| 28 | 0.0149 | 0.378 | 0.0015 in |
| 30 | 0.0120 | 0.305 | 0.0015 in |
A one-gauge step in any sheet metal gauge calculator result is not a fixed amount. From 3 to 14 gauge each number drops about 0.0150 in.
From 22 to 26 gauge each number drops only 0.0030 in, so in the thin range of a sheet metal gauge chart each step is just 0.076 mm.
Steel thicker than 3/16 in (0.1875 in) is normally sold as plate by its decimal or fraction size, not by a sheet metal gauge calculator number.
That puts 3 to 6 gauge, from 0.2391 down to 0.1943 in, in plate territory, and 7 gauge at 0.1793 in is the thickest common steel gauge.
Same Gauge Number, Different Metal
16 gauge is 0.0508 in in aluminum and 0.0650 in in copper, a 28% gap under one number. Each metal follows its own gauge standard, so any sheet metal gauge calculator answer has to name the metal before the number means anything.
| Gauge | Mild Steel | Galvanized | Stainless | Aluminum or Brass | Copper | SWG |
|---|---|---|---|---|---|---|
| 10 | 0.1345 | 0.1382 | 0.1406 | 0.1019 | 0.1340 | 0.1280 |
| 12 | 0.1046 | 0.1084 | 0.1094 | 0.0808 | 0.1090 | 0.1040 |
| 14 | 0.0747 | 0.0785 | 0.0781 | 0.0641 | 0.0830 | 0.0800 |
| 16 | 0.0598 | 0.0635 | 0.0625 | 0.0508 | 0.0650 | 0.0640 |
| 18 | 0.0478 | 0.0516 | 0.0500 | 0.0403 | 0.0490 | 0.0480 |
| 20 | 0.0359 | 0.0396 | 0.0375 | 0.0320 | 0.0350 | 0.0360 |
| 22 | 0.0299 | 0.0336 | 0.0312 | 0.0253 | 0.0280 | 0.0280 |
| 24 | 0.0239 | 0.0276 | 0.0250 | 0.0201 | 0.0220 | 0.0220 |
| 26 | 0.0179 | 0.0217 | 0.0187 | 0.0159 | 0.0180 | 0.0180 |
| 28 | 0.0149 | 0.0187 | 0.0156 | 0.0126 | 0.0140 | 0.0148 |
Every sheet metal gauge calculator value in the table is in inches, and each column follows its own standard. Mild steel uses Manufacturers' Standard Gauge and stainless the 1893 US Standard Gauge.
Aluminum and brass use Brown and Sharpe (AWG), copper uses the Birmingham Wire Gauge, and SWG is the British Standard Wire Gauge.
Galvanized gauges run 0.0037 to 0.0038 in thicker than bare steel at every number, because the zinc is part of the stated thickness.
Continental Steel describes each galvanized gauge as 2.5 oz per square foot heavier than its US Standard Gauge counterpart.
That Brown and Sharpe formula sets the aluminum and brass thickness t in inches for gauge number n. Each step changes thickness by a factor of 1.12293, so 16 gauge works out to 0.05082 in, or 1.291 mm.
Stainless sits close to fractions because the 1893 US Standard was built on them. 16 gauge stainless is exactly 1/16 in (0.0625 in), while 16 gauge mild steel is 0.0598 in, so the two are not swappable on a tight fit.
Weight of a 4 × 8 Sheet by Gauge
A 4 × 8 ft sheet of 16 gauge steel weighs 80.0 lb by mill book weight and 78.1 lb by steel's density of 7,850 kg/m³. A 16 gauge aluminum sheet of the same size weighs 22.8 lb.
Here w is weight in lb per square foot, t is thickness in inches and ρ is density in lb per cubic foot. Steel at 490.1 lb/ft³ gives 2.442 lb/sq ft at 16 gauge, aluminum at 168.6 lb/ft³ gives 0.714 lb/sq ft.
Manufacturers' Standard Gauge was set from weight, at 41.82 lb per square foot for each inch of thickness. Suppliers bill steel and galvanized by this book weight, which runs 2.3% above the density figure, so 16 gauge books at 2.500 lb/sq ft.
| Gauge | Steel, Density | Steel, Book | Galvanized, Book | Stainless | Aluminum | Copper |
|---|---|---|---|---|---|---|
| 10 | 175.8 lb | 180.0 lb | 184.9 lb | 187.3 lb | 45.8 lb | 199.9 lb |
| 14 | 97.6 lb | 100.0 lb | 105.1 lb | 104.0 lb | 28.8 lb | 123.8 lb |
| 16 | 78.1 lb | 80.0 lb | 85.0 lb | 83.2 lb | 22.8 lb | 97.0 lb |
| 18 | 62.5 lb | 64.0 lb | 69.1 lb | 66.6 lb | 18.1 lb | 73.1 lb |
| 20 | 46.9 lb | 48.0 lb | 53.0 lb | 49.9 lb | 14.4 lb | 52.2 lb |
| 22 | 39.1 lb | 40.0 lb | 45.0 lb | 41.6 lb | 11.4 lb | 41.8 lb |
| 24 | 31.2 lb | 32.0 lb | 36.9 lb | 33.3 lb | 9.0 lb | 32.8 lb |
Stainless weights in this sheet metal gauge calculator table use 8,000 kg/m³ and copper 8,960 kg/m³. Galvanized book weights match the 2.656 lb/sq ft that Continental Steel lists for 16 gauge, so a 4 × 8 sheet of it weighs 85.0 lb.
The 2.3% gap between book weight and a density-based sheet metal gauge calculator weight matters on a full order.
Fifty sheets of 16 gauge steel come to 4,001 lb on a book-weight invoice but 3,907 lb by density, so use book weight for freight and density for the part that ends up on the scale.
A 4 × 8 ft sheet is 2.973 m². In metric terms 16 gauge steel books at 12.21 kg/m², or 36.3 kg per sheet, against 11.92 kg/m² and 35.4 kg by density.
Aluminum has no book scale, so its weight always comes from density. 16 gauge aluminum weighs 3.49 kg/m², or 10.4 kg, in a 4x8 sheet metal gauge calculator check.
Measured Thickness to Gauge
A caliper reading of 0.075 in is 14 gauge steel, only 0.4% over its 0.0747 in size. A 0.060 in reading is 16 gauge steel and a 0.048 in reading is 18 gauge.
Metric sheet often sits between gauges, so the nearest number in a sheet metal gauge calculator can mislead. Each common metric thickness sits next to its closest gauge, and a minus sign means the sheet is thinner than that gauge.
| Measured | Mild Steel | Stainless | Aluminum | SWG |
|---|---|---|---|---|
| 0.5 mm | 25 Ga (-5.8%) | 26 Ga (+5.3%) | 24 Ga (-2.1%) | 25 SWG (-1.6%) |
| 0.8 mm | 21 Ga (-4.3%) | 22 Ga (+0.9%) | 20 Ga (-1.5%) | 21 SWG (-1.6%) |
| 1.0 mm | 19 Ga (-5.8%) | 20 Ga (+5.0%) | 18 Ga (-2.3%) | 19 SWG (-1.6%) |
| 1.2 mm | 18 Ga (-1.2%) | 18 Ga (-5.5%) | 17 Ga (+4.4%) | 18 SWG (-1.6%) |
| 1.5 mm | 16 Ga (-1.2%) | 17 Ga (+5.1%) | 15 Ga (+3.5%) | 17 SWG (+5.5%) |
| 2.0 mm | 14 Ga (+5.4%) | 14 Ga (+0.8%) | 12 Ga (-2.6%) | 14 SWG (-1.6%) |
| 2.5 mm | 12 Ga (-5.9%) | 13 Ga (+5.0%) | 10 Ga (-3.4%) | 12 SWG (-5.4%) |
| 3.0 mm | 11 Ga (-1.2%) | 11 Ga (-5.5%) | 9 Ga (+3.2%) | 11 SWG (+1.8%) |
A 1.5 mm sheet is a close stand-in for 16 gauge steel, but in aluminum it lands near 15 gauge, not 16. A 1 mm sheet sits 5.8% off 19 gauge steel, which usually means it was made to a metric size.
Measure in two spots at least an inch in from the edge, since sheared edges roll over. A reading more than about 6% off the nearest gauge of the expected metal points to metric stock or a different metal.
Coatings add to the caliper reading before any sheet metal gauge calculator lookup, and galvanized sheet reads 0.0037 in thicker than bare steel at the same gauge.
That makes a 0.0635 in reading on zinc-coated sheet 16 gauge galvanized, even though it falls halfway between 15 and 16 gauge bare steel.
SWG Sizes Used in India and the UK
18 SWG is 1.219 mm, almost the same as 18 gauge US steel at 1.214 mm, but 16 SWG is 1.626 mm, 7.0% thicker than the US 16 gauge of 1.519 mm.
Indian and older British sheet is often quoted in SWG, so a sheet metal gauge calculator in mm needs that scale too.
| Gauge | SWG (mm) | US Steel MSG (mm) | SWG vs MSG | SWG Steel, 8 × 4 ft Sheet |
|---|---|---|---|---|
| 10 | 3.251 | 3.416 | -4.8% | 75.9 kg |
| 12 | 2.642 | 2.657 | -0.6% | 61.6 kg |
| 14 | 2.032 | 1.897 | +7.1% | 47.4 kg |
| 16 | 1.626 | 1.519 | +7.0% | 37.9 kg |
| 18 | 1.219 | 1.214 | +0.4% | 28.5 kg |
| 20 | 0.914 | 0.912 | +0.3% | 21.3 kg |
| 22 | 0.711 | 0.759 | -6.4% | 16.6 kg |
| 24 | 0.559 | 0.607 | -7.9% | 13.1 kg |
| 26 | 0.457 | 0.455 | +0.6% | 10.7 kg |
Sheet weights use 7,850 kg/m³ over an 8 × 4 ft sheet of 2.973 m². A sheet metal gauge calculator for India therefore needs the SWG column, since 16 gauge from a local yard weighs 37.9 kg while US 16 gauge weighs 35.4 kg on the same density basis.
The swing runs both ways. At 14 and 16 gauge SWG is about 7% thicker than US steel, while at 22 and 24 gauge it is 6 to 8% thinner, so a drawing that mixes the two systems should state millimeters rather than a bare gauge.
Nearest Fraction and Metric Sheet
16 gauge steel is closest to 1/16 in but 0.0027 in thinner, and closest to 1.5 mm metric sheet at 0.019 mm over. Gauges are not exact fractions, so a fractional stand-in for a sheet metal gauge calculator result can be far off in thin sheet.
| Steel Gauge | Decimal (in) | Nearest Fraction | Gauge vs Fraction | Nearest Metric | Gauge vs Metric |
|---|---|---|---|---|---|
| 7 | 0.1793 | 11/64 in | +0.0074 in | 5 mm | -0.446 mm |
| 10 | 0.1345 | 9/64 in | -0.0061 in | 3 mm | +0.416 mm |
| 11 | 0.1196 | 1/8 in | -0.0054 in | 3 mm | +0.038 mm |
| 12 | 0.1046 | 7/64 in | -0.0048 in | 2.5 mm | +0.157 mm |
| 14 | 0.0747 | 5/64 in | -0.0034 in | 2 mm | -0.103 mm |
| 16 | 0.0598 | 1/16 in | -0.0027 in | 1.5 mm | +0.019 mm |
| 18 | 0.0478 | 3/64 in | +0.0009 in | 1.2 mm | +0.014 mm |
| 20 | 0.0359 | 1/32 in | +0.0047 in | 0.9 mm | +0.012 mm |
| 22 | 0.0299 | 1/32 in | -0.0014 in | 0.8 mm | -0.041 mm |
| 24 | 0.0239 | 1/32 in | -0.0073 in | 0.6 mm | +0.007 mm |
Fractions work best in the middle of the sheet metal gauge calculator range. 18 gauge is within 0.0009 in of 3/64 in, but 24 gauge is 0.0073 in thinner than 1/32 in, so a 1/32 in sheet would be about 31% thicker than the 24 gauge it replaces.
Metric stand-ins are closest at 11, 16, 18, 20 and 24 gauge, each within 0.04 mm of a metric size. 10 gauge at 3.416 mm is 0.416 mm over 3 mm, and 7 gauge is 0.446 mm under 5 mm.
Reading Gauge Charts and Gauge Numbers
A gauge number only becomes a size once the metal and its standard are known. Across the seven standards in a sheet metal gauge calculator, 16 gauge spans 0.0508 to 0.0650 in, so read the column before the number.
What is a sheet metal gauge size reference chart?
A sheet metal gauge size reference chart lists gauge numbers against decimal thickness for each metal. A sound chart names the standard for every column, such as Manufacturers' Standard Gauge for steel and Brown and Sharpe for aluminum.
Charts disagree most on copper. One supplier chart lists 16 gauge copper at 0.065 in on the Birmingham scale, while a chart built on Brown and Sharpe lists 0.0508 in, so confirm which scale a copper column uses before ordering.
How do I evaluate a sheet metal thickness gauge chart?
Check a few fixed values first, the same ones used to test a sheet metal gauge calculator. At 16 gauge, mild steel should read 0.0598 in and galvanized 0.0635 in.
Stainless should read 0.0625 in and aluminum 0.0508 in, so a chart that lists 0.0598 in for stainless has mixed up its columns.
Then check the weight basis if the chart lists weights. A 16 gauge steel figure of 2.500 lb/sq ft is book weight, and 2.442 lb/sq ft is density weight, so the two charts can both be right and still differ by 2.3%.
What is a sheet metal gauge used for?
Sheet metal gauge is used to order, quote and specify thin sheet for ducts, enclosures, roofing and brackets.
Thickness from a sheet metal gauge calculator drives every downstream number, so 10 gauge needs 2.25 times the punch force of 16 gauge for the same hole.
The Punch Force Calculator and the K-Factor Calculator both start from the decimal thickness. Thin gauge also limits threads, since 16 gauge steel holds only 1.2 threads of a 1/4-20, and the Tap Drill Size Calculator sizes the hole for that tap.
What is a sheet metal gauge number?
A sheet metal gauge number is a position on a thickness scale where a higher number means thinner metal. On the steel sheet metal gauge calculator scale, thickness runs from 3 gauge at 0.2391 in down to 30 gauge at 0.0120 in, a 20-to-1 range.
The reverse order comes from wire drawing, where each number marked one more pass through a smaller die. Brown and Sharpe keeps that logic in its formula, with 36 gauge fixed at 0.005 in and each lower number 12.3% thicker.