Soffit Calculator

Updated

Soffit Calculator for soffit area from eave run and overhang depth, with panels by area and by cut layout, fascia boards, F and J-channel, attic intake vent area and full job cost.

Quick Setup

Measure eave run along the wall on every side with soffit, and overhang from wall to fascia.

ft
in
ft
Waste, Trim and Corners12% waste, 16 ft fascia
%
in
corners
in
ft
Attic Ventilation2,000.0 sq ft attic, 1/150 rule

Check the free area printed on your panel label and enter it per linear foot.

sq ft
sq in per ft
Material and Labor Prices$1,360.00 total
$ each
$ each
$ each
$ per ft of eave
Soffit to Order
30 Soffit Panels
29.87 exact, Vinyl 12 in Triple 4, 12.0 sq ft usable each
320.0 sq ft Soffit Area
Order Area With 12% Waste358.4 sq ft
Area per Foot of Eave2.00 sq ft
Eave run times overhang depth, plus hip corner squares and rake soffit. This is the soffit square footage.
27 Panels by Cut Layout
Pieces Cut per Panel6 pieces
Offcut Left per Panel0.00 in
Count from cutting each panel into overhang-length pieces, before any extra waste allowance is added on.
16 Fascia Boards
F and J-Channel, 12 ft Pieces14 + 14 pcs
Fascia Length With Waste246.4 ft
Fascia runs along every eave and rake. F and J-channel hold the soffit edges at the wall and fascia side.
150% of Intake Vent Needed
Intake Vent Area Provided1,440 sq in
Intake Vent Area Needed960 sq in
Soffit intake should supply at least half of the attic vent area the code requires, so fresh air can flow.
Live Eave Section Diagram24.00 in overhang, vented
Material List and Cost$1,360.00 for 30 panels
Soffit Panel Size ChartFor a 24.00 in overhang
Step-by-Step Soffit MathWith your numbers
    Soffit Order Ready
    Order 30 panels, 16 fascia boards and 28 channel pieces. Leave a small gap at each end for expansion.

    Panel Counts From a Soffit Calculator

    In soffit calculator math, 160 ft of eave with a 24 in overhang is 320 sq ft of soffit. With 12% waste, that is 358.4 sq ft, or 30 vinyl panels at 12 in by 12 ft, since each panel covers 12 sq ft.

    A is the soffit area in square feet, Le the eave run along the wall in feet, and d the overhang depth from wall to fascia in inches. Measure the run on every side that gets soffit.

    The table runs that soffit calculator square feet math across common eave runs and overhangs for 12 in vinyl panels, 12 ft long. Each cell gives the area, then the panels to order by area with 12% waste.

    Eave Run12 in Overhang16 in Overhang18 in Overhang24 in Overhang
    100 ft100 sq ft, 10 panels133.3 sq ft, 13 panels150 sq ft, 14 panels200 sq ft, 19 panels
    120 ft120 sq ft, 12 panels160 sq ft, 15 panels180 sq ft, 17 panels240 sq ft, 23 panels
    160 ft160 sq ft, 15 panels213.3 sq ft, 20 panels240 sq ft, 23 panels320 sq ft, 30 panels
    200 ft200 sq ft, 19 panels266.7 sq ft, 25 panels300 sq ft, 28 panels400 sq ft, 38 panels
    250 ft250 sq ft, 24 panels333.3 sq ft, 32 panels375 sq ft, 35 panels500 sq ft, 47 panels

    In a soffit calculator count, a 16 in vinyl or aluminum panel covers 16 sq ft over the same 12 ft length, so the 160 ft, 24 in roof drops from 30 panels to 23. Four by eight plywood sheets at 32 sq ft each take 12.

    A 12% waste allowance sits at the top of the 10 to 12% range common in any soffit square footage calculator estimate. It covers end cuts, damaged pieces and the trim-to-fit pieces at corners, not the offcuts a bad overhang depth leaves behind.

    Overhang Depths That Waste Panels

    A soffit calculator count for a 30 in overhang on 160 ft of eave comes to 45 panels, not the 38 the simple area rule gives with 12% waste. Each 12 ft panel cuts into only four 30 in pieces, so 24 in of every panel ends up as offcut.

    Soffit pieces run across the overhang, from wall to fascia, so a soffit calculator count has to cut each panel into overhang-length pieces. Only the pieces that fit count as coverage, and the leftover counts as nothing.

    Cu is the usable coverage per panel in square feet, w the panel's exposed width in inches, Lp the panel length in inches and d the overhang depth in inches. The floor term is the whole pieces each panel yields.

    For the soffit calculator order, divide the soffit area with waste by that usable coverage and round up. At 30 in, a 12 in by 12 ft panel gives 10 sq ft usable instead of its full 12 sq ft, which is why the order climbs from 38 to 45 panels.

    Overhang DepthPieces per 12 ft PanelOffcut per PanelUsable per PanelSimple Area RulePanels to Order
    12 in120 in12.0 sq ft1515
    14 in104 in11.7 sq ft1818
    16 in90 in12.0 sq ft2020
    18 in80 in12.0 sq ft2323
    20 in74 in11.7 sq ft2526
    22 in612 in11.0 sq ft2830
    24 in60 in12.0 sq ft3030
    26 in514 in10.8 sq ft3336
    29 in428 in9.7 sq ft3745
    30 in424 in10.0 sq ft3845
    36 in40 in12.0 sq ft4545

    Soffit calculator depths that divide 144 in evenly, like 12, 16, 18, 24 and 36 in, waste nothing in the cut. At 22, 26, 29 and 30 in the simple rule runs 2 to 8 panels short on this house.

    A 22 in overhang needs as many panels as a 24 in one, and 29 to 36 in all need 45. If the overhang is still being framed, building it at a depth that divides the panel length gets every inch of soffit you pay for.

    The 12% waste in a soffit calculator estimate sits on top of the usable count, for end cuts and damaged pieces. Cut pieces alone, with no waste at all, would still need 40 panels at 30 in, more than the simple rule's 38 with waste.

    Intake Vent Area for Vented Soffit

    A 2,000 sq ft attic under the 1/150 rule needs 1,920 sq in of total vent area, and at least half of it, 960 sq in, should come in at the soffit. That takes 106.7 ft of vented soffit rated at 9 sq in per foot.

    The ratio comes from IRC Section R806.2, which sets net free ventilating area at 1/150 of the vented attic.

    The same section allows 1/300 when 40 to 50% of the vent area sits within 3 ft of the ridge, with a Class I or II vapor retarder also tied to climate zones 6 to 8.

    Vin is the intake vent area in square inches, Aattic the attic floor area in square feet, R the ratio of 150 or 300, and 144 turns square feet into square inches.

    Attic Floor AreaRuleIntake NeededSoffit at 5.9 sq in/ftSoffit at 9 sq in/ftSoffit at 19.6 sq in/ft
    1,000 sq ft1/150480 sq in81.4 ft53.3 ft24.5 ft
    1,500 sq ft1/150720 sq in122.0 ft80.0 ft36.7 ft
    2,000 sq ft1/150960 sq in162.7 ft106.7 ft49.0 ft
    2,000 sq ft1/300480 sq in81.4 ft53.3 ft24.5 ft
    2,500 sq ft1/1501,200 sq in203.4 ft133.3 ft61.2 ft
    3,000 sq ft1/1501,440 sq in244.1 ft160.0 ft73.5 ft

    Free area per foot varies by panel more than any other input. Quality Edge lists its 12 in center vent at 5.9 and its 12 in fully vented panel at 19.6, and Gibraltar rates its 16 in aluminum center vent at 6.48 sq in per foot.

    That spread decides whether a vented soffit calculator check passes. On 160 ft of eave, center-vent panels at 5.9 give 944 sq in, just under the 960 needed, while fully vented panels at 19.6 give 3,136 sq in, more than three times it.

    Solid soffit adds nothing to a soffit vent calculator total, so a solid run needs gable or other low vents to reach the same 960 sq in. IRC R806.1 also limits vent openings to between 1/16 and 1/4 in, which keeps insects out of the attic.

    Fascia Boards, F-Channel and J-Channel

    160 ft of eave plus 60 ft of rake is 220 ft of fascia. With 12% waste that is 246.4 ft, or 16 boards at 16 ft, while 10 ft boards would take 25 to cover the same run.

    Fascia Stock LengthBoards for 246.4 ft
    10 ft25
    12 ft21
    14 ft18
    16 ft16

    Fascia runs along every eave and every rake, but soffit only goes where there is an overhang to close. That is why a soffit and fascia calculator total needs the rake run for fascia even when the rakes carry no soffit.

    In a soffit calculator trim count, F-channel holds the soffit at the wall and J-channel at the fascia side, each in 12 ft pieces. The 160 ft eave takes 14 pieces of each, and channel only follows the rakes when the rakes get soffit too.

    Fascia takes the same waste allowance as the panels, while channel gets none, since 12 ft channel pieces butt end to end with little cutting. Add a piece per run if you lap the joints.

    Hip Corners and Rake Soffit

    A 40 x 30 ft hip-roof house with 24 in overhangs has 296 sq ft of soffit and needs 28 panels. Each of its four outside corners adds a 24 x 24 in square of soffit and 4 ft of extra fascia around the turn.

    A is the soffit area in square feet, Le the eave run along the walls, d the overhang depth in inches and nc the number of outside hip corners. The corner squares sit outside the wall line, so the eave run misses them.

    40 x 30 ft House, 24 in OverhangSoffit AreaPanelsFascia LengthFascia Boards, 16 ftF + J-Channel
    Hip roof, 4 corners296 sq ft28156 ft1112 + 13
    Gable, no rake soffit160 sq ft15147.1 ft117 + 7
    Gable, 12 in rake soffit227.1 sq ft22147.1 ft1113 + 13

    The gable rakes in this soffit calculator example run 67.1 ft in total, four rakes of 16.77 ft each on a 6/12 roof with a 15 ft run. Rake length follows the slope, so measure along the roof edge, not the wall.

    Include gable ends in soffit calculator area only when the rakes overhang enough to need a closed underside. A 12 in rake soffit on this house adds 67.1 sq ft, 7 more panels and doubles the channel, so it changes the order more than the hips do.

    For soffit calculator rake inputs, rake run follows from the pitch and the run, which the Rafter Length Calculator works out from span and pitch. Eave and rake lengths also feed the Drip Edge Calculator for the edge metal above the fascia.

    Soffit in Meters and Square Centimeters

    48 m of eave with a 600 mm overhang is 28.8 m² of soffit, or 30 panels of 12 in by 12 ft vinyl with 12% waste, since 600 mm pieces leave 58 mm of each panel unused. Fascia for that eave plus 18 m of rake comes to 66 m before waste.

    Metric soffit calculator vent math works the same way. A 200 m² attic under the 1/150 rule needs 6,667 cm² of intake, and fully vented soffit rated at 9 sq in per foot, which is 190.5 cm² per meter, supplies 9,144 cm² along 48 m, or 137% of the need.

    Panel stock in Canada and other metric markets is still often sold in imperial widths and lengths. For a soffit calculator Canada estimate, measure in meters but keep the panel coverage in its own unit, 1.11 m² for a 12 in by 12 ft panel.

    Choosing, Sizing and Pricing Soffit

    The three questions below come up most when soffit is ordered. Each answer uses a house not already worked above, so the numbers add a new case.

    How to calculate soffit size?

    For a soffit calculator size, multiply the eave run by the overhang depth, add a square per outside hip corner, plus any rake soffit. Then divide by usable coverage per panel after waste, which falls below panel area when pieces leave an offcut.

    A 24 x 40 ft hip-roof house has 128 ft of eave. With 16 in overhangs, that is 170.7 sq ft plus four 16 in corner squares of 1.78 sq ft each, for 177.8 sq ft, or 17 panels of 12 in by 12 ft vinyl with 12% waste.

    In the soffit calculator cut layout, each 12 ft panel yields nine 16 in pieces with no offcut, so usable coverage is the full 12 sq ft. The 17 panels stand, and cutting alone, before waste, uses 16.

    How do you calculate a soffit installation cost?

    Add panels times panel price, fascia boards times board price and channel pieces times channel price, then add labor per foot of eave. At $22 a panel, $28 a fascia board and $9 a channel piece, the 160 ft, 24 in job comes to $1,360 in materials.

    That soffit calculator material figure is $4.25 per sq ft of soffit, or $1.83 per sq ft for the vinyl panels alone. Labor at $3 per foot of eave adds $480 for a $1,840 total, and $5 per foot brings it to $2,160.

    For a 200 ft eave at 16 in, with $25 panels, $30 fascia boards, $10 channel and $4 per foot of labor, the job is 25 panels, 19 boards and 34 channel pieces, or $2,335. Swap in your local prices, since vinyl, aluminum and labor vary widely by region.

    How do I choose the right soffit material?

    Choose by panel size and venting first, since material changes a soffit calculator count less than width does. On the 160 ft, 24 in example, 12 in vinyl or aluminum takes 30 panels, 16 in panels take 23 and 4 x 8 plywood takes 12 sheets.

    Soffit PanelCoverage EachPieces per Panel at 24 inBy Area With 12% WasteBy Cut Layout
    Vinyl 12 in Triple 4, 12 ft12 sq ft63027
    Vinyl 16 in Quad 4, 12 ft16 sq ft62320
    Aluminum 12 in, 12 ft12 sq ft63027
    Aluminum 16 in, 12 ft16 sq ft62320
    Plywood Sheet, 4 x 8 ft32 sq ft2 strips1210

    Vinyl and aluminum come in solid, center vented and fully vented versions, so they can carry the whole intake. Plywood needs separate vents cut in, which makes the vent area a design step rather than a panel choice.

    Set the venting from the free area the attic needs, using the soffit calculator intake table above. Aluminum and vinyl panels of the same width give the same count, so the choice between them comes down to price and finish.