Hip Roof Calculator

Updated

Hip Roof Calculator that takes wall length, width, pitch and eave overhang to common, hip and jack rafters with the cuts, plus the ridge, roof area, roof space and a shingle order.

Quick Setup

Measure the walls, not the eaves. Length runs along the ridge, width from wall to wall.

Framing and Hip Typeequal pitch, 16 in o.c.

Spacing sets the rafter and jack counts. Unequal end pitch gives the ends a different slope from the long sides.

Materials and Cost15% waste, no price

Hip roofs waste more shingles at the hips. Add your installed price per square to see a cost.

%
$/sq
Hip Roof Area
1,502.6 sq ft Roof Surface
Each long side 465.1 sq ft · each end 286.2 sq ft
17 ft 10 5/8 in Common Rafter
Ridge Height Above Wall7 ft 6 in
Roof Angle26.57°
Common rafter runs from the ridge to the eave tip, overhang included. Deduct half the ridge board thickness.
24 ft Hip Rafter
Hip Angle19.47°
Hip Run to Wall Corner21 ft 2 1/2 in
Hip rafters run from each corner tip to the ridge end. Four are needed, each longer than a common.
3,375 cu ft Roof Space
Ridge Length10 ft
Hip and Ridge Cap106 ft
Air space under the roof above the top plates. Cap length covers all four hips and the ridge.
17.28 Squares to Order
Shingle Bundles52 bundles
4×8 Sheathing55 sheets
A square covers 100 sq ft of shingles on the slopes. Counts include your waste allowance.
Hip Roof Framing DiagramPlan view, your numbers
10 ft ridge24 ft hip465.1 sq fteach side40 ft length30 ft width1 ft eave overhang
Rafter Cut ListLengths include the eave tail
MemberLongestEach NextCountPlumb LineSide Cut
Commons17 ft 10 5/8 in-1826.57°square
Hip Rafters24 ft-419.47°45.00° both cheeks
Jack Rafters17 ft 6 1/4 in1 ft 5 7/8 in shorter8826.57°45.00° bevel
Shingle and Material Order52 bundles, 5 cap, 55 sheets
ItemOrderBased On
Field Shingles52 bundles17.28 squares × 3 bundles
Hip and Ridge Cap5 bundles106.0 ft ÷ 25.00 ft per bundle
Starter Strip2 bundles148.0 ft of eaves ÷ 100.00 ft
Underlayment2 rolls1,502.6 sq ft ÷ 1,000 sq ft per roll
4×8 Sheathing55 sheets1,728.0 sq ft ÷ 32 sq ft per sheet
Drip Edge16 pieces148.0 ft ÷ 9.83 ft per 10 ft piece after 2 in laps
Hip Roof Angle ChartYour building at each pitch
PitchRoof AngleHip AngleCommon FactorHip FactorRoof Area
2/129.46°6.72°× 1.014× 1.4241,362.5 sq ft
3/1214.04°10.02°× 1.031× 1.4361,385.4 sq ft
4/1218.43°13.26°× 1.054× 1.4531,416.7 sq ft
5/1222.62°16.42°× 1.083× 1.4741,456.0 sq ft
6/12 (yours)26.57°19.47°× 1.118× 1.5001,502.6 sq ft
7/1230.26°22.42°× 1.158× 1.5301,556.0 sq ft
8/1233.69°25.24°× 1.202× 1.5631,615.3 sq ft
9/1236.87°27.94°× 1.250× 1.6011,680.0 sq ft
10/1239.81°30.51°× 1.302× 1.6411,749.5 sq ft
12/1245.00°35.26°× 1.414× 1.7321,900.7 sq ft
14/1249.40°39.52°× 1.537× 1.8332,065.2 sq ft
16/1253.13°43.31°× 1.667× 1.9442,240.0 sq ft
Step-by-Step Math7 steps with your numbers
  1. Slope: m = 0.5 (6/12, 26.5651°)
  2. Ridge height: H = 30 ÷ 2 × 0.5 = 7.5 ft
  3. Common rafter: (15 + 1) × √(1 + 0.5²) = 17.8885 ft
  4. Hip rafter: (15 + 1) × √(2 + 0.5²) = 24 ft
  5. Ridge length: 40 - 2 × 15 = 10 ft
  6. Roof area: 42 × 32 × 1.11803 = 1,502.6 sq ft
  7. Roof space: 7.5 ÷ 6 × (40 × 30 + 10 × 0 + 50 × 30) = 3,375 cu ft
Ready to Frame and Order
Cut one hip and one common, test them at a corner, then cut the rest. Rafter lengths run to the ridge centerline.

Hip Roof Calculator Example: 40 x 30 ft at 6/12

A 40 x 30 ft house with a 6/12 hip roof and 1 ft eaves needs four 24 ft hip rafters, commons of 17 ft 10 5/8 in and a 10 ft ridge. The roof covers 1,502.6 sq ft.

In any hip roof calculator estimate, the ridge stands 15 x 0.5 = 7.5 ft above the wall plates. Its length is the wall length minus the width, 40 - 30 = 10 ft, because each hip end takes half the width off both ends of the ridge.

Rc is the common rafter, W is the wall-to-wall width, e is the level eave overhang and P is the rise per 12 in of run. At 6/12 the root is 1.118, so the common is 16 x 1.118 = 17.89 ft to the ridge centerline.

The 2 under the root is there because the hip runs on the diagonal, 1.414 ft of plan run for each foot of common run. At 6/12 the hip factor is exactly 1.5, so the hip is 16 x 1.5 = 24 ft, including a 1 ft 6 in tail.

Multiplying the common by 1.414 is a shortcut some framers use for the hip, and it gives 25 ft 3 5/8 in here, 1 ft 3 5/8 in too long. The shortcut stretches the rise as well as the run, and the rise never changes.

Each long side is a trapezoid of 465.1 sq ft and each end a triangle of 286.2 sq ft. Together they make 1,502.6 sq ft, the same as the 42 x 32 ft eave outline times 1.118, a quick check on any hip roof calculator area.

Angle Chart for Common and Hip Rafters

A 6/12 roof slopes at 26.57°, but its hips slope at only 19.47°. The hip climbs the same rise over 1.414 times the run, so every hip is flatter than the roof it frames.

The hip roof angle chart below gives both angles for each pitch, plus the length factors per foot of common run. The last column is the hip length per 12 in of common run, read straight off a framing square.

PitchRoof AngleHip AngleCommon FactorHip FactorHip Length per 12 in of Run
3/1214.04°10.02°1.0311.43617.23 in
4/1218.43°13.26°1.0541.45317.44 in
5/1222.62°16.42°1.0831.47417.69 in
6/1226.57°19.47°1.1181.50018.00 in
7/1230.26°22.42°1.1581.53018.36 in
8/1233.69°25.24°1.2021.56318.76 in
9/1236.87°27.94°1.2501.60119.21 in
10/1239.81°30.51°1.3021.64119.70 in
12/1245.00°35.26°1.4141.73220.78 in

In hip roof calculator cut lists, the hip angle is also the hip's plumb cut from a square cut. On a framing square, a 6/12 hip is laid out as 6 in of rise over 17 in of run, since the hip covers 16.97 in of plan run for every 12 in of common run.

A level held on a hip reads only 4.24 in per 12 on a 6/12 roof. Take the pitch for a hip roof calculator estimate from a common rafter or the fascia line, or convert a measured angle with the Roof Pitch Calculator.

Jack Rafter Lengths and Side Cuts

At 16 in on center, each jack in a hip roof calculator layout for the 40 x 30 roof is 1 ft 5 7/8 in shorter than the one before it. The 6/12 roof takes 88 jacks, and the longest is 17 ft 6 1/4 in with its eave tail.

J is the common difference between neighbouring jacks and S is the rafter spacing. At 16 in and 6/12 that is 16 x 1.118 = 17.89 in, which marks every jack from one pattern.

Spacing changes a hip roof calculator piece count more than any other framing choice, since each hip carries jacks on both faces. The counts below are for the 40 x 30 ft roof at 6/12.

SpacingCommonsHipsJacksTotal PiecesJack StepLongest Jack
16 in184881101 ft 5 7/8 in17 ft 6 1/4 in
24 in14456742 ft 2 7/8 in16 ft 9 1/4 in

Every jack and hip cheek on an equal-pitch hip is cut with a 45° saw bevel along the plumb line, at any pitch. The hip sits at 45° in plan, and tilting the blade along a plumb line copies that plan angle exactly.

Commons and jacks take the 26.57° plumb cut at 6/12, and the hips take their own 19.47° cut. The Birdsmouth Cut Calculator sizes the seat where each one crosses the wall.

A hip roof framing diagram puts the two king commons at each ridge end, one to the side wall and one to the end wall. The jacks then fill both faces of every hip, shortening by one step toward the corner.

Unequal End Pitch Moves the Hips Off 45°

Steeper ends shorten the hips and lengthen the ridge in hip roof calculator math. Framing the 40 x 30 house at 6/12 on the sides and 8/12 on the ends stretches the ridge from 10 ft to 17 ft 6 in, since each end now runs only 11.25 ft.

The end overhang has to shrink to 9 in to keep the fascia level all round. At 8/12 a full 1 ft overhang would drop 8 in, while the 6/12 sides drop only 6 in, leaving the end fascia 2 in low.

40 x 30 ft House6/12 All Round6/12 Sides, 8/12 Ends
Ridge length10 ft17 ft 6 in
Hip rafter with tail24 ft21 ft 6 1/2 in
Hip slope19.47°21.80°
Hip cheek bevels45° and 45°36.87° and 53.13°
Side jack step1 ft 5 7/8 in1 ft 11 7/8 in
End jack step1 ft 5 7/8 in1 ft 2 3/8 in
Roof area1,502.6 sq ft1,516.9 sq ft

Side jacks then take a 53.13° bevel and end jacks a 36.87° bevel, so the two faces of each hip no longer share a jack pattern. Any hip roof calculator layout with mixed pitches needs both sets marked and cut separately.

Pyramid and Flat-Top Hip Roofs

A 30 x 30 ft pyramid hip roof at 6/12 with 1 ft eaves has four equal faces of 286.2 sq ft, 1,144.9 sq ft in all. The four 24 ft hips meet at a point 7 ft 6 in above the walls.

Pyramid hip roof calculator math is the regular hip with the length equal to the width, so the ridge is 30 - 30 = 0. The cap covers the hips only, 96 ft or 4 bundles, and every jack pattern repeats on all four faces.

Flat-top hip roof calculator math stops the slopes at a deck. The 40 x 30 house at 6/12 with its deck 4 ft above the walls runs 8 ft in from each wall, which leaves a 24 x 14 ft deck of 336 sq ft.

Shingles cover only the 1,127.0 sq ft of slopes, which is 39 bundles at 15% waste. The hips shrink to 13 ft 6 in and the commons to 10 ft 3/4 in, both stopping at the deck header.

The deck needs 386.4 sq ft of low-slope membrane with the same 15% waste. Asphalt shingles are not allowed below 2/12 under IRC R905.2.2, summarized in the LSU AgCenter roofing guide.

Cap, Starter and Drip Edge Lengths

A hip roof calculator order for the 40 x 30 roof includes 106 ft of hip and ridge cap, 148 ft of starter and 148 ft of drip edge. A hip roof has no rakes, so the whole 42 x 32 ft eave outline takes both starter and drip edge.

Cap length is four hips plus the ridge, 4 x 24 + 10 = 106 ft, or 5 bundles at 25 linear ft per bundle. A gable on the same walls caps only its 42 ft ridge, which is 2 bundles.

Starter runs at 100 linear ft per bundle when each strip is cut in half, per GAF's WeatherBlocker sell sheet. The 148 ft outline needs 2 bundles.

Drip edge pieces must overlap at least 2 in under IRC R905.2.8.5, as framing writer Mike Guertin explains in JLC. Each 10 ft piece then covers 9 ft 10 in, so 148 ft takes 16 pieces in a hip roof calculator count, not 15.

The same 148 ft sets the gutter and soffit runs, and the Drip Edge Calculator and Soffit Calculator work from it. Synthetic underlayment for the 6/12 roof is 2 rolls of 10 squares.

Below 4/12 the underlayment doubles. The same house at 3/12 has 1,385.4 sq ft of slope but needs 3 rolls, because two layers are required from 2/12 up to 4/12.

Meters and Square Feet for the Same House

A 12 x 8 m house with a 30° hip roof and 0.6 m eaves has 140.23 m² of roof. The ridge is 4.0 m long and sits 2.31 m above the walls, with commons of 5.31 m and hips of 7.03 m.

A 30° roof equals a 6.93/12 pitch and a 1.1547 pitch factor. The formulas stay the same for a hip roof calculator in meters, as long as every length is in meters, and this roof holds 86.22 m³ above the walls.

Shingles sold by the US square cover 100 sq ft, or 9.29 m². The 12 x 8 m roof is 17.36 squares with 15% waste, so it takes 53 bundles at 3 bundles per square.

The 40 x 30 ft example is 12.19 x 9.14 m in metric. Its 1,502.6 sq ft of roof is 139.60 m², and its 24 ft hips are 7.32 m, so hip roof calculator square feet and m² totals convert at 10.764 sq ft per m².

Working Out a Hipped Roof by Hand

Hand math and hip roof calculator math need the same four measurements, the wall length, wall width, pitch and eave overhang. The answers below work them through on 36 x 24 ft and 30 x 40 ft houses.

How to calculate hipped roof?

Calculate a hipped roof in five steps, the rise, ridge, common, hip and area. For a 36 x 24 ft house at 5/12 with 1 ft eaves, the rise is 12 x 5/12 = 5 ft and the ridge is 36 - 24 = 12 ft.

The common is 13 x 1.0833 = 14 ft 1 in, and the hip is 13 x 1.474 = 19 ft 2 in. By the hip roof calculation formula for area, the 38 x 26 ft eave outline times 1.0833 gives 1,070.3 sq ft.

How do you measure a hip roof?

Measure a hip roof at the walls, outside to outside, then add the level eave overhang and the pitch. Before trusting any hip roof calculator result, check a regular hip from the ground, because its ridge is always the length minus the width.

On a 40 x 30 ft house, a 10 ft ridge confirms equal pitch all round. A 17 ft 6 in ridge on the same walls means steeper ends, such as 8/12 ends on 6/12 sides.

How to work out hip length?

Work out hip length as the square root of the side run squared, plus the end run squared, plus the rise squared. Then add the eave tail, measured the same way from the overhangs.

Here a is the side run, b is the end run and H is the rise. On the 40 x 30 roof, the square root of 152 + 152 + 7.52 is 22.5 ft to the wall corner, and the 1.5 ft tail brings it to 24 ft.

The same rule covers unequal pitch. With 8/12 ends, the square root of 152 + 11.252 + 7.52 is 20.19 ft, and a 1.35 ft tail makes the hip 21 ft 6 1/2 in. The Rafter Length Calculator covers commons on their own.

How do I estimate shingle bundles for a hip roof?

Estimate shingle bundles as the sloped area plus waste, divided by 100 for squares, times 3 bundles per square. The 40 x 30 roof at 6/12 needs 52 bundles at 15% waste, plus 5 bundles of cap.

WasteSquaresShingle Bundles4 x 8 Sheets
10%16.535052
15%17.285255
20%18.035557

Every hip line cuts shingles on both faces, against two rake edges on a gable, so hip roofs need more waste. Going from 10% to 15% waste in a hip roof calculator for shingles estimate costs only 2 more bundles here.

The Roof Shingle Calculator takes any of these areas to a full shingle order for other roof shapes as well.

How to calculate roof space?

Calculate the roof space of a regular hip roof from the rise, width and length. By hip roof calculator math, the 40 x 30 ft roof at 6/12 holds 3,375 cu ft above the wall plates.

H is the rise above the plates, W the width and L the length. A gable of the same pitch on the same walls holds 4,500 cu ft, so the hip keeps 1 - W/(3L) of it, which is 75% here.

How many square feet is a 30x40 roof?

A 30x40 hip roof at 6/12 is 1,341.6 sq ft measured to the walls and 1,502.6 sq ft with 1 ft eaves. Each pitch step adds roughly 3% to 4% to the roof.

PitchNo Overhang1 ft EavesSquares at 15% WasteBundles
4/121,264.9 sq ft1,416.7 sq ft16.2949
5/121,300.0 sq ft1,456.0 sq ft16.7451
6/121,341.6 sq ft1,502.6 sq ft17.2852
7/121,389.2 sq ft1,556.0 sq ft17.8954
8/121,442.2 sq ft1,615.3 sq ft18.5856
9/121,500.0 sq ft1,680.0 sq ft19.3258
10/121,562.0 sq ft1,749.5 sq ft20.1261
12/121,697.1 sq ft1,900.7 sq ft21.8666

These hip roof calculator areas match a gable at the same pitch and overhangs exactly, since both equal the eave outline times the same factor. The Gable Roof Area Calculator shows the gable side; a hip costs more in cap and cuts, not in roof area.

How do I calculate roof size?

Calculate roof size as the eave plan area times the pitch factor, for any roof with one pitch, a fast check on any hip roof calculator area. The 40 x 30 ft house has a 42 x 32 ft eave outline of 1,344 sq ft, and 1,344 x 1.118 = 1,502.6 sq ft.

Mixed pitches need each face worked on its own, which is why the 8/12-end version comes to 1,516.9 sq ft. The Roofing Calculator covers whole houses with more than one roof section.