Sprinkler calculator for heads by throw and wind, zones from tap flow, precipitation rate, weekly run time with cycle and soak on your soil, PVC pipe sizes, gallons and water cost.
Measure the lawn and read the radius and full-circle flow from the nozzle chart at your water pressure.
Spacing, Wind and Supply Limit
Parts Prices for the Estimate
Schedule, Soil and Water Cost
Sprinkler Layout Diagram
Head Spacing Chart
| Wind | Square Spacing | Triangular Spacing | Single Row |
|---|---|---|---|
| Calm, 0-3 mph | 16.5 ft (55%) | 18 ft (60%) | 15 ft (50%) |
| Light, about 4 mph | 15 ft (50%) | 16.5 ft (55%) | 15 ft (50%) |
| Breezy, about 8 mph | 13.5 ft (45%) | 15 ft (50%) | 13.5 ft (45%) |
Pipe Size Chart for Your Zone Flow
| Schedule 40 PVC | Inside Diameter | Max Flow at 5 ft/s | Speed at 8.33 GPM | Loss per 100 ft |
|---|---|---|---|---|
| ½ in | 0.622 in | 4.74 GPM | 8.79 ft/s | 21.57 psi |
| ¾ in | 0.824 in | 8.31 GPM | 5.01 ft/s | 5.48 psi |
| 1 in | 1.049 in | 13.5 GPM | 3.09 ft/s | 1.69 psi |
| 1¼ in | 1.380 in | 23.3 GPM | 1.79 ft/s | 0.44 psi |
| 1½ in | 1.610 in | 31.7 GPM | 1.31 ft/s | 0.21 psi |
| 2 in | 2.067 in | 52.3 GPM | 0.80 ft/s | 0.06 psi |
Parts List and Cost Estimate
| Part | Quantity | Price | Cost |
|---|---|---|---|
| Sprinkler heads | 24 heads | $6.50 each | $156.00 |
| Zone valves | 7 valves | $35.00 each | $245.00 |
| Pipe, row runs plus one header | 320 ft | $0.60 per ft | $192.00 |
| Controller, 7 stations or more | 1 | $120.00 each | $120.00 |
| Parts total | 24 heads, 7 zones | $29.71 per head | $713.00 |
Run Time by Watering Days
| Days per Week | Minutes per Zone | Water per Watering | Cycles on Your Soil |
|---|---|---|---|
| 1 | 40 min | 1.27 in | 2 × 20 min |
| 2 | 20 min | 0.63 in | 2 × 10 min |
| 3 | 13 min | 0.42 in | 2 × 6.6 min |
| 4 | 10 min | 0.32 in | 2 × 5 min |
| 5 | 8 min | 0.25 in | 2 × 4 min |
| 6 | 6.6 min | 0.21 in | 2 × 3.3 min |
| 7 | 5.7 min | 0.18 in | 2 × 2.8 min |
Soil Intake Rate Chart
| Soil, Grass Cover, 0-5% Slope | Max Rate | Your 1.91 in/hr | Watering |
|---|---|---|---|
| Coarse Sand | 2 in/hr | Under the limit | One run |
| Coarse Sand Over Hardpan | 1.75 in/hr | 1.1× the limit | 2 cycles |
| Light Sandy Loam | 1.75 in/hr | 1.1× the limit | 2 cycles |
| Sandy Loam Over Hardpan | 1.25 in/hr | 1.5× the limit | 2 cycles |
| Silt Loam | 1 in/hr | 1.9× the limit | 2 cycles |
| Silt Loam Over Hardpan | 0.6 in/hr | 3.2× the limit | 4 cycles |
| Clay or Clay Loam | 0.2 in/hr | 9.5× the limit | 10 cycles |
Step-by-Step Sprinkler Math
Head Spacing by Throw and Wind in a Sprinkler Calculator
A 70 by 40 ft lawn watered by 15 ft spray heads needs 24 heads on a square layout: 4 quarter-circle corners, 12 half-circle edge heads and 8 full-circle heads inside. The throw radius sets every sprinkler calculator head count.
Rain Bird names head-to-head spacing, 50% of the throw diameter, as the most common way to get even coverage. In still air, the University of Arizona's irrigation course allows 55% of the diameter on a square and 60% on a triangle.
Here S is the widest gap allowed between heads, R is the nozzle's throw radius and p is the spacing share for the wind. A 15 ft radius in calm air gives 0.55 × 30 = 16.5 ft on a square.
Here N is the heads along one side of length L, rounded up so no gap passes S. Along 70 ft that is 5 spaces and 6 heads set 14 ft apart, and the 40 ft side takes 4 rows 13.3 ft apart.
This sprinkler head spacing chart lists the widest gap for common spray and rotor radii. The 0 to 3 and 4 to 7 mph shares follow the Arizona course; the 8 mph row tightens to 45% and 50%.
| Throw Radius | Calm, Square | Calm, Triangle | 4 to 7 mph, Square | 4 to 7 mph, Triangle | 8 mph, Square |
|---|---|---|---|---|---|
| 8 ft | 8.8 ft | 9.6 ft | 8.0 ft | 8.8 ft | 7.2 ft |
| 10 ft | 11.0 ft | 12.0 ft | 10.0 ft | 11.0 ft | 9.0 ft |
| 12 ft | 13.2 ft | 14.4 ft | 12.0 ft | 13.2 ft | 10.8 ft |
| 15 ft | 16.5 ft | 18.0 ft | 15.0 ft | 16.5 ft | 13.5 ft |
| 25 ft | 27.5 ft | 30.0 ft | 25.0 ft | 27.5 ft | 22.5 ft |
| 30 ft | 33.0 ft | 36.0 ft | 30.0 ft | 33.0 ft | 27.0 ft |
| 35 ft | 38.5 ft | 42.0 ft | 35.0 ft | 38.5 ft | 31.5 ft |
| 40 ft | 44.0 ft | 48.0 ft | 40.0 ft | 44.0 ft | 36.0 ft |
Wind changes the sprinkler calculator head count, not just the gap. At 8 mph the 70 by 40 ft lawn needs 28 square-spaced heads instead of 24, because 13.5 ft spacing takes 6 spaces along 70 ft.
A triangular sprinkler calculator layout is not always leaner on a rectangle. In calm air it uses 22 heads on that lawn, 2 fewer than the square, but at 8 mph it needs 32 against the square's 28.
Any residential sprinkler calculator head count depends on lawn shape as much as area. The table below uses calm air, with the square layout split into quarter, half and full-circle heads.
| Lawn | Throw Radius | Square Layout Heads | Quarter / Half / Full | Square Spacing | Triangle Layout Heads |
|---|---|---|---|---|---|
| 30 × 20 ft | 12 ft | 12 | 4 / 6 / 2 | 10.0 × 10.0 ft | 13 |
| 30 × 20 ft | 15 ft | 9 | 4 / 4 / 1 | 15.0 × 10.0 ft | 10 |
| 50 × 30 ft | 15 ft | 15 | 4 / 8 / 3 | 12.5 × 15.0 ft | 13 |
| 70 × 40 ft | 15 ft | 24 | 4 / 12 / 8 | 14.0 × 13.3 ft | 22 |
| 70 × 40 ft | 30 ft | 12 | 4 / 6 / 2 | 23.3 × 20.0 ft | 10 |
| 100 × 60 ft | 15 ft | 40 | 4 / 18 / 18 | 14.3 × 15.0 ft | 37 |
| 100 × 60 ft | 30 ft | 15 | 4 / 8 / 3 | 25.0 × 30.0 ft | 13 |
Zone Count From Supply Flow and the 75% Rule
In a sprinkler calculator zone count, the 24-head layout draws 55.5 GPM with every head on, so a 12 GPM supply has to be split into 7 zones. Each zone is held to 75% of the supply, which is 9 GPM.
The Rain Bird Landscape Irrigation Design Manual caps irrigation flow through a meter at 75% of its maximum safe flow. It also keeps meter pressure loss under 10% of static pressure and service-line speed at 5 to 7.5 ft/s.
Here Q is the total flow, qf is one full-circle head's flow and each N is the count of heads with that arc. Matched-precipitation nozzles flow in proportion to their arc, so a half circle uses half a full circle's flow.
Here Z is the zone count and F is the measured supply flow. For the default lawn, 55.5 ÷ 9 = 6.17, so 7 zones; Rain Bird's rough valve estimate is the same total flow divided by the flow available.
Whole heads can't be split, so the sprinkler calculator answer comes from sharing them out until no zone passes 9 GPM. The busiest of the 7 zones carries 8.33 GPM on 3 or 4 heads.
A how many sprinklers per zone calculator answer depends on the arc. With 15 ft sprays at 3.7 GPM per full circle, this sprinkler zone size chart gives the most heads of one arc that a single zone can run.
| Supply Flow | Usable at 75% | Full-Circle Heads | Half-Circle Heads | Quarter-Circle Heads |
|---|---|---|---|---|
| 6 GPM | 4.5 GPM | 1 | 2 | 4 |
| 8 GPM | 6 GPM | 1 | 3 | 6 |
| 10 GPM | 7.5 GPM | 2 | 4 | 8 |
| 12 GPM | 9 GPM | 2 | 4 | 9 |
| 15 GPM | 11.25 GPM | 3 | 6 | 12 |
| 20 GPM | 15 GPM | 4 | 8 | 16 |
For the same 24-head lawn, the sprinkler calculator zone count falls as supply rises. Using the full supply instead of 75% saves zones but leaves no margin when a tap runs in the house.
| Supply Flow | Zones at 75% | Busiest Zone | Zones at 100% |
|---|---|---|---|
| 8 GPM | 10 | 5.55 GPM | 8 |
| 10 GPM | 8 | 7.40 GPM | 6 |
| 12 GPM | 7 | 8.33 GPM | 5 |
| 15 GPM | 5 | 11.10 GPM | 4 |
| 20 GPM | 4 | 13.88 GPM | 3 |
Precipitation Rate of Sprays, Rotors and Mixed Arcs
The 70 by 40 ft spray layout puts down 1.91 in/hr. Precipitation rate is the depth of water a zone lays on the lawn in one hour, and it sets every sprinkler calculator run time that follows.
Here PR is in inches per hour, Q is the flow in GPM and A is the watered area in square feet. The constant is 231 cubic inches per gallon times 60 minutes, divided by 144 square inches.
For the default lawn, 96.25 × 55.5 GPM ÷ 2,800 sq ft = 1.91 in/hr. Rain Bird's own sprinkler calculator rounds the constant to 96.3, which changes the result by under 0.1%.
In metric, PR in mm/hr equals 60 times the flow in L/min, divided by the area in m². The same lawn is 260.1 m², so its rate works out to 48.5 mm/hr.
| Head and Spacing | Full-Circle Flow | Area per Head | Precipitation Rate |
|---|---|---|---|
| 15 ft spray, 15 × 15 ft | 3.7 GPM | 225 sq ft | 1.58 in/hr |
| 30 ft rotor, 30 × 30 ft | 3.0 GPM | 900 sq ft | 0.32 in/hr |
| 30 ft rotor, 30 × 30 ft | 4.0 GPM | 900 sq ft | 0.43 in/hr |
When the nozzle chart is missing, the full-circle flow comes from the bore and the pressure at the head, using the discharge formula in Rain Bird's sprinkler calculator.
Here q is the flow in GPM, d is the nozzle bore in inches, P is the pressure in psi and 0.97 is the discharge coefficient. A 1/8 in bore flows 2.86 GPM at 40 psi and 2.48 GPM at 30 psi.
A 5/32 in bore at 50 psi works out to 4.99 GPM, matching the 5 GPM that Rain Bird's agricultural guide lists for that nozzle and pressure. In metric, a 3.5 mm bore at 2.8 bar gives 3.50 GPM.
Sprays lay down about five times the depth of rotors in the same hour. Rain Bird advises against putting heads on one valve when their rates differ by more than 10%, so sprays and rotors go on separate zones.
To measure your sprinkler precipitation rate and check a sprinkler calculator figure on site, set catch cups across the zone and run it. Cups holding an average of 0.5 in after 20 minutes mean 0.5 ÷ 20 × 60 = 1.5 in/hr.
Run Time per Week and the Uniformity Multiplier
In a sprinkler calculator schedule at 1.91 in/hr, 1 in a week over 3 watering days takes 13.3 minutes per zone each time, allowing for uneven coverage. Rotors at 0.5 in/hr need 50.6 minutes for the same job.
Oklahoma State University Extension puts warm-season grass at about 1 in a week and cool-season grass at up to 2 in in summer. The same fact sheet calls a DU of 70% to 80% good for a home lawn.
Distribution uniformity compares the driest quarter of the catch cups to the average. A lawn with 65% DU gets only 0.65 in in its driest quarter when the average is 1 in, so the run has to be longer.
Here SM is the scheduling multiplier and DU is a decimal. UC Davis uses this formula to scale run time, and the Irrigation Association prefers it because it overwaters less when uniformity is poor.
The common shortcut in sprinkler calculator schedules divides the weekly need by DU instead. The two methods split further as uniformity drops, which matters most on older spray systems.
| DU | Scheduling Multiplier | 1 ÷ DU | Weekly Water for 1 in Net |
|---|---|---|---|
| 50% | 1.43 | 2.00 | 1.43 in |
| 55% | 1.37 | 1.82 | 1.37 in |
| 60% | 1.32 | 1.67 | 1.32 in |
| 65% | 1.27 | 1.54 | 1.27 in |
| 70% | 1.22 | 1.43 | 1.22 in |
| 75% | 1.18 | 1.33 | 1.18 in |
| 80% | 1.14 | 1.25 | 1.14 in |
| 85% | 1.10 | 1.18 | 1.10 in |
At 65% DU, dividing by DU asks for 1.54 in and 16.1 minutes per watering, while the multiplier asks for 1.27 in and 13.3 minutes. The shortcut puts down about 22% more water every week.
Here t is minutes per zone each watering day, D is the weekly depth after the multiplier, n is the number of watering days and PR is in inches per hour.
| Days per Week | Spray Zone at 1.91 in/hr | Water per Watering | Rotor Zone at 0.5 in/hr |
|---|---|---|---|
| 1 | 39.8 min | 1.27 in | 151.9 min |
| 2 | 19.9 min | 0.63 in | 75.9 min |
| 3 | 13.3 min | 0.42 in | 50.6 min |
| 4 | 10.0 min | 0.32 in | 38.0 min |
| 5 | 8.0 min | 0.25 in | 30.4 min |
| 6 | 6.6 min | 0.21 in | 25.3 min |
| 7 | 5.7 min | 0.18 in | 21.7 min |
The weekly total stays the same however it is split: about 40 minutes per spray zone or 152 minutes per rotor zone. A sprinkler schedule calculator only decides how those minutes are spread across the days.
Soil Intake Limits and Cycle and Soak
Silt loam under grass on flat ground takes in about 1 in/hr, so the sprinkler calculator schedule for the 1.91 in/hr spray layout is 2 cycles of 6.6 minutes, with a soak of at least 7 minutes between them.
Rain Bird publishes the USDA's maximum precipitation rates by soil, cover and slope in its soil design note. The flat-ground limit starts at 2.00 in/hr for coarse sandy soil.
Here C is the number of cycles and I is the soil's intake rate in in/hr. Each soak lasts at least the cycle time multiplied by (PR ÷ I - 1), so the soil can take in what ran on too fast.
| Soil, Grass Cover, 0 to 5% Slope | Max Rate | Cycles at 1.91 in/hr | Cycles at 1.58 in/hr | Cycles at 0.5 in/hr |
|---|---|---|---|---|
| Coarse sand | 2.00 in/hr | 1 | 1 | 1 |
| Coarse sand over hardpan | 1.75 in/hr | 2 | 1 | 1 |
| Light sandy loam | 1.75 in/hr | 2 | 1 | 1 |
| Sandy loam over hardpan | 1.25 in/hr | 2 | 2 | 1 |
| Silt loam | 1.00 in/hr | 2 | 2 | 1 |
| Silt loam over hardpan | 0.60 in/hr | 4 | 3 | 1 |
| Clay or clay loam | 0.20 in/hr | 10 | 8 | 3 |
Clay is where sprays struggle: 10 cycles of 1.3 minutes with soaks of at least 12 minutes. A rotor zone at 0.5 in/hr needs only 3 cycles on the same clay, which makes rotors the better match for heavy soil.
A percolation test gives your own soil's rate in place of the chart; the Soil Infiltration Rate Calculator turns the test readings into in/hr.
Pipe Size for Each Zone's Flow
In the default sprinkler calculator layout, the busiest zone at 8.33 GPM needs 1 in Schedule 40 PVC. A ¾ in pipe would carry it at 5.01 ft/s, just past the 5 ft/s that Rain Bird's design manual gives as the accepted maximum velocity.
Here v is the water speed in ft/s, Q is the zone flow in GPM and d is the pipe's inside diameter in inches. Schedule 40 inside diameters run from 0.622 in for ½ in pipe to 2.067 in for 2 in pipe.
| Schedule 40 PVC | Inside Diameter | Max Flow at 5 ft/s | Speed at 8.33 GPM | Loss per 100 ft at 8.33 GPM |
|---|---|---|---|---|
| ½ in | 0.622 in | 4.7 GPM | 8.79 ft/s | 21.57 psi |
| ¾ in | 0.824 in | 8.3 GPM | 5.01 ft/s | 5.48 psi |
| 1 in | 1.049 in | 13.5 GPM | 3.09 ft/s | 1.69 psi |
| 1¼ in | 1.380 in | 23.3 GPM | 1.79 ft/s | 0.44 psi |
| 1½ in | 1.610 in | 31.7 GPM | 1.31 ft/s | 0.21 psi |
| 2 in | 2.067 in | 52.3 GPM | 0.80 ft/s | 0.06 psi |
Friction loss uses Hazen-Williams with C = 150, the factor Rain Bird's calculator applies to PVC. The Hazen Williams Equation Calculator runs the same loss for other pipe lengths and materials.
A 15 GPM zone moves up to 1¼ in pipe, because 1 in pipe would run at 5.57 ft/s and lose 5.03 psi per 100 ft. Mainline sizing for the whole supply belongs in the Water Pipe Size Calculator.
Gallons per Week and Water Cost
An inch of water is 0.62 gallons per square foot, according to Purdue's Landscape Report. One net inch on the 2,800 sq ft lawn is 1,745 gallons, and at 65% DU the system pumps 2,209.
A water sprinkler calculator cost figure follows from that volume. At $4.50 per 1,000 gallons the default lawn costs $9.94 a week, or $43.08 a month over 52 ÷ 12 weeks.
| Lawn Area | Net 1 in | Pumped at 65% DU | Cost per Week | Cost per Month | If Divided by DU |
|---|---|---|---|---|---|
| 1,000 sq ft | 623 gal | 789 gal | $3.55 | $15.39 | 959 gal |
| 2,800 sq ft | 1,745 gal | 2,209 gal | $9.94 | $43.08 | 2,685 gal |
| 5,000 sq ft | 3,117 gal | 3,945 gal | $17.75 | $76.94 | 4,795 gal |
| 10,000 sq ft | 6,234 gal | 7,891 gal | $35.51 | $153.87 | 9,590 gal |
Billing units vary by utility. A charge per 100 cu ft covers 748 gallons and one per m³ covers 264 gallons, so convert the rate to per 1,000 gallons before using it in any sprinkler calculator cost figure.
Bucket Tests, Rain and System Estimates
Supply flow drives every zone count, and it takes a bucket and a stopwatch to measure. The other questions here cover Hunter's zone tool, rain and building a cost estimate.
How do I measure GPM for my sprinkler system?
Time a bucket at the outdoor tap nearest the meter with nothing else running. A 5 gal bucket that fills in 25 seconds means 5 ÷ 25 × 60 = 12 GPM, and a 10 L bucket in 20 seconds means 30 L/min, or 7.9 GPM.
Plan each zone on 75% of that reading, the sprinkler calculator usable flow, which is 9 GPM for the 12 GPM tap. The Gallons Per Minute Calculator (GPM) converts other bucket sizes and fill times.
What is the Hunter sprinkler zone calculator?
It is Hunter Industries' online tool for adding up nozzle flows and checking them against a zone's capacity. The arithmetic matches any sprinkler calculator zone count: total the head flows and keep each zone under the usable supply.
With 9 GPM usable and 15 ft sprays flowing 3.7 GPM per full circle, one zone holds 2 full-circle, 4 half-circle or 9 quarter-circle heads, or a mix whose flows add up to no more than 9 GPM.
How does a sprinkler system estimate work?
A sprinkler system estimate starts from the sprinkler calculator quantities, then prices them. The 70 by 40 ft lawn comes to 24 heads, 7 zone valves and a 7-station controller, with 1 in lateral pipe for zones up to 13.5 GPM.
Pipe is taken as one run along each row of heads plus a header across the lawn: 4 × 70 + 40 = 320 ft. At $6.50 a head, $35 a valve, $0.60 per ft and a $120 controller, parts come to $713, or $29.71 per head, before labor.
Should I adjust irrigation for rain?
Subtract measured rain from the weekly need in the sprinkler calculator schedule. Half an inch of rain cuts the spray layout from 13.3 to 6.6 minutes per watering and the week's water from 2,209 to 1,105 gallons.
Michigan State University Extension notes it makes no difference whether the inch falls as rain or comes from a hose. A rain gauge in the lawn gives the number to subtract.