Sump pump size calculator for basement pits, sizing pump GPM from a basin rise test, roof runoff or a known inflow, then the total head, cycle time and sump dimensions from liters.
With the pump off during heavy inflow, time how far the water rises in one minute.
Fittings and Pump Check
Basin Depth and Float Switch
Sump Pump Diagram
Sump Pump Size Chart by Pipe Size
| Pipe Size | Inside Diameter | Velocity | Total Head | Fitting Length |
|---|---|---|---|---|
| 1-1/4 in | 1.380 in | 3.54 ft/s | 11.60 ft | 18.4 ft |
| 1-1/2 in | 1.610 in | 2.60 ft/s | 10.81 ft | 21.5 ft |
| 2 in | 2.067 in | 1.58 ft/s | 10.27 ft | 27.6 ft |
| 2-1/2 in | 2.469 in | 1.11 ft/s | 10.13 ft | 32.9 ft |
| 3 in | 3.068 in | 0.72 ft/s | 10.05 ft | 40.9 ft |
Step-by-Step Sump Pump Math
Sump Pump Size Calculator Math From a One-Minute Rise
A standard 18 in sump basin holds 1.10 gallons per inch of depth, so water rising 10 inches in one minute is 11.0 GPM of inflow. With a 1.5 safety factor the pump must deliver 16.5 GPM, or about 990 gallons per hour, at the system's total head.
Q is the target pump flow in GPM, d is the basin's inside diameter in inches, R is the rise in inches per minute and SF is the safety factor. The 231 converts cubic inches to US gallons.
Measure during the heaviest rain you can, with the pump unplugged and a tape held against the basin wall.
One minute is long enough to read and short enough that the basin will not overflow, and it is the reading every sump pump size calculator rise estimate starts from.
| Basin diameter | Gallons per inch | Liters per inch | Volume, 24 in deep |
|---|---|---|---|
| 14 in | 0.67 gal | 2.52 L | 16.0 gal |
| 18 in | 1.10 gal | 4.17 L | 26.4 gal |
| 20 in | 1.36 gal | 5.15 L | 32.6 gal |
| 24 in | 1.96 gal | 7.41 L | 47.0 gal |
| 30 in | 3.06 gal | 11.58 L | 73.4 gal |
The basin's diameter matters more than its depth in sump pump size calculator rise math. The same 10 in rise means 11.0 GPM in an 18 in basin but 19.6 GPM in a 24 in basin, so a rise reading without the diameter tells you nothing.
| Rise in 18 in basin | Measured inflow | Target at 1.5 | Target at 2.0 |
|---|---|---|---|
| 2 in/min | 2.2 GPM | 3.3 GPM | 4.4 GPM |
| 5 in/min | 5.5 GPM | 8.3 GPM | 11.0 GPM |
| 10 in/min | 11.0 GPM | 16.5 GPM | 22.0 GPM |
| 15 in/min | 16.5 GPM | 24.8 GPM | 33.0 GPM |
| 20 in/min | 22.0 GPM | 33.0 GPM | 44.1 GPM |
Use 2.0 instead of 1.5 when the measured storm was mild or the water table runs high. That one choice moves a 10 in/min basement from 16.5 to 22.0 GPM in the sump pump size calculator result, which can change the pump you buy.
Roof and Yard Runoff as Pump Inflow
A 1,200 sq ft roof draining to the pit in a 2 in/hr storm sends 22.4 GPM to the pump, with a runoff coefficient of 0.9. This sump pump size calculator for basement inflow suits a new pit with no storm to measure yet.
A is the drainage area in square feet, i is the rainfall intensity in inches per hour, C is the share of rain that runs off and 7.48 is gallons per cubic foot. The 12 and 60 turn inches into feet and hours into minutes.
| Rainfall | 1,200 sq ft inflow | 1,200 sq ft target at 1.5 | 2,000 sq ft inflow | 2,000 sq ft target at 1.5 |
|---|---|---|---|---|
| 1 in/hr (25 mm/hr) | 11.2 GPM | 16.8 GPM | 18.7 GPM | 28.1 GPM |
| 2 in/hr (51 mm/hr) | 22.4 GPM | 33.7 GPM | 37.4 GPM | 56.1 GPM |
| 3 in/hr (76 mm/hr) | 33.7 GPM | 50.5 GPM | 56.1 GPM | 84.2 GPM |
| 4 in/hr (102 mm/hr) | 44.9 GPM | 67.3 GPM | 74.8 GPM | 112 GPM |
Runoff into a sump is far larger than groundwater seepage. A downspout tied into the pit can triple the sump pump size calculator target, so routing roof water away from the foundation is often cheaper than a bigger pump.
A sump pump size calculator square feet estimate needs a local rainfall figure, not a national average. The NOAA Atlas 14 precipitation frequency data gives the US design intensity for a chosen storm length and return period.
The Storm Water Runoff Calculator works the same rational method for larger sites, with runoff coefficients for lawns, gravel and paving.
Discharge Head, Pipe Size and Check Valve
Pushing 16.5 GPM up 10 ft through 25 ft of 1-1/2 in Schedule 40 PVC, two elbows and a check valve takes 10.8 ft of total dynamic head. Of that sump pump size calculator head, 10 ft is lift, 0.44 ft is pipe friction and 0.37 ft is fittings.
Each fitting counts as extra pipe, measured in pipe diameters. A 90° elbow equals 30 diameters, a 45° elbow 16 and a swing check valve 100, so in 1-1/2 in pipe the check valve alone acts like 13.4 ft of pipe.
| Sch 40 PVC size | Velocity at 16.5 GPM | Fitting length | Total head | Water held in 25 ft |
|---|---|---|---|---|
| 1-1/4 in | 3.54 ft/s | 18.4 ft | 11.60 ft | 1.94 gal |
| 1-1/2 in | 2.60 ft/s | 21.5 ft | 10.81 ft | 2.64 gal |
| 2 in | 1.58 ft/s | 27.6 ft | 10.27 ft | 4.36 gal |
| 2-1/2 in | 1.11 ft/s | 32.9 ft | 10.13 ft | 6.22 gal |
| 3 in | 0.72 ft/s | 40.9 ft | 10.05 ft | 9.60 gal |
For a typical basement, this sump pump pipe size chart shows lift dominates and pipe size barely moves the head.
Going from 1-1/2 in to 2 in saves just 0.54 ft, while the larger pipe holds 1.7 gallons more water that drains back if the check valve fails.
Lift and flow both push the head up. At 40 GPM the same 1-1/2 in line needs 12.15 ft for an 8 ft lift and 20.15 ft for a 16 ft lift, so a high-flow pit on a deep basement needs the sump pump size calculator head read at the higher flow.
Friction uses the Hazen-Williams head form at C 150 for PVC. The Total Dynamic Head Calculator takes the same sum further when a long or pressurized discharge line needs every fitting counted.
Horsepower Labels Versus the Duty Point
Horsepower does not tell you whether a pump can keep up. The Zoeller Model 53, a 3/10 HP pump, is rated at 43 GPM at zero head and 19.25 ft maximum head on its 50 Series sales sheet.
The 43 GPM figure applies only with no lift at all. At 19.25 ft of head the same pump moves nothing, so any basement needing more than about 19 ft of total head is out of its range, whatever the horsepower.
The duty point from any sump pump size calculator is the flow you need at the head you have. For the 10 in/min basement it is 16.5 GPM at 10.8 ft, and any pump whose curve passes above that point works, whether it is labeled 1/4, 1/3 or 1/2 HP.
Two pumps with the same horsepower can deliver very different flows at 10 ft, since impeller design sets the curve. Carry the duty point to the maker's curve, not to the price tag or the horsepower on the box.
Cycle Time, Float Band and Basin Size
A 35 GPM pump in an 18 in basin with an 8 in float band runs only 22 seconds per cycle against 11.0 GPM of inflow.
It starts about 51 times an hour, and runs under one minute wear the motor and switch, so a sump pump size calculator check of cycle time matters as much as flow.
trun is the run time in minutes, Vband is the water between the float's on and off levels in gallons, Qpump is the pump's flow at the system head and Qin is the inflow, both in GPM.
| Basin | Float band | Water per cycle | Run at 35 GPM | Starts per hour |
|---|---|---|---|---|
| 18 in | 4.25 in | 4.68 gal | 12 s | 96.7 |
| 18 in | 8 in | 8.81 gal | 22 s | 51.4 |
| 18 in | 12 in | 13.22 gal | 33 s | 34.3 |
| 24 in | 8 in | 15.67 gal | 39 s | 28.9 |
| 24 in | 12 in | 23.50 gal | 59 s | 19.3 |
| 30 in | 12 in | 36.72 gal | 92 s | 12.3 |
The 4.25 in band matches the Model 53's float, which turns on at 7-1/4 in and off at 3 in. A built-in float that short in a small basin almost guarantees short cycling with a strong pump, whatever the sump pump size calculator flow says.
Matching the pump to the sump pump size calculator target fixes it too. In the 18 in basin with an 8 in band, a 20 GPM pump runs 59 seconds per cycle, while a 50 GPM pump runs just 14 seconds and starts 58.5 times an hour.
A basement sump pump size chart that ranks pumps by flow alone misses this. Light seepage of 2 in/min still gives a 35 GPM pump only 16 second runs, though the starts drop to 14.1 an hour.
Underground Sump Dimensions From Liters
For an underground water tank, the sump pump size calculator math runs from liters to floor size, with the water depth set first.
A 12,000 liter sump with 2 m of water needs a 2.45 × 2.45 m floor, or about 8.0 × 8.0 ft. Add 0.3 m of freeboard and the inside depth is 2.3 m, or 7.5 ft.
Area is the capacity in cubic meters divided by the water depth in any sump pump size calculator metric check.
So 12 m³ at 2 m deep needs 6 m² of floor. The square side is the square root of that area, and a round sump uses the diameter that gives the same area.
| Capacity | US gallons | Square, 2 m water | Square, 1.5 m water | Round, 2 m water |
|---|---|---|---|---|
| 2,000 L | 528 gal | 1.00 m (3.28 ft) | 1.15 m (3.79 ft) | 1.13 m dia |
| 5,000 L | 1,321 gal | 1.58 m (5.19 ft) | 1.83 m (5.99 ft) | 1.78 m dia |
| 10,000 L | 2,642 gal | 2.24 m (7.34 ft) | 2.58 m (8.47 ft) | 2.52 m dia |
| 12,000 L | 3,170 gal | 2.45 m (8.04 ft) | 2.83 m (9.28 ft) | 2.76 m dia |
| 15,000 L | 3,963 gal | 2.74 m (8.98 ft) | 3.16 m (10.37 ft) | 3.09 m dia |
| 20,000 L | 5,283 gal | 3.16 m (10.37 ft) | 3.65 m (11.98 ft) | 3.57 m dia |
| 50,000 L | 13,209 gal | 5.00 m (16.40 ft) | 5.77 m (18.94 ft) | 5.64 m dia |
The freeboard space is real volume you pay to dig beyond the sump pump size calculator water depth, so keep it to the 0.3 m you need.
In the 12,000 liter sump, 0.3 m above the water holds another 1,800 liters, and each centimeter of water depth stores 60 liters for reading a level gauge.
Plastering or waterproofing that 12,000 liter sump covers 22.5 m² of inside wall plus 6 m² of floor, 28.5 m² in all. A 2:1 rectangle at the same depth measures 3.46 × 1.73 m.
The Tank Volume Calculator works the other way, from the sizes of an existing tank back to its liters or gallons.
Basement Pump Sizing, Backup and Overflow
Each answer below works fresh numbers through the same sump pump size calculator math as the tables above.
How to calculate sump pump size?
Find the inflow in GPM, multiply it by a safety factor, then add the lift and pipe friction to get the total head. The pump must deliver that sump pump size calculator flow at that head on its curve.
For a crawl space basin rising 4 in/min in an 18 in pit, inflow is 4.4 GPM and the 1.5 target is 6.6 GPM. With 4 ft of lift and 20 ft of 1-1/4 in pipe, two elbows and a check valve, the head is 4.26 ft.
What is the standard size for a sump pump?
The common home setup is a 1/3 HP submersible pump with a 1-1/2 in discharge in an 18 in basin, and SumpDirect notes 1/3 HP as the usual choice. Larger 1/2 and 3/4 HP pumps serve high-inflow pits.
"Standard" only works when the sump pump size calculator duty point fits. A basement with 16 ft of lift and 40 GPM of target flow needs 20.15 ft of head, more than the Model 53's 19.25 ft maximum.
What is the required sump size in feet for a water capacity of 12000 liters?
A 12,000 liter sump at 2 m water depth needs about 8.0 × 8.0 ft inside, with a total depth of 7.5 ft once 0.3 m of freeboard is added. At 1.5 m of water the square grows to 9.3 × 9.3 ft.
A 10,000 liter sump at 2 m of water measures 7.3 × 7.3 ft. A rectangular 2:1 version at the same depth is 10.4 × 5.2 ft, which fits a narrow side yard better.
What size fitting for sump pump?
Most residential sump pumps have a 1-1/2 in discharge, and the Model 53 uses 1-1/2 in NPT. Run 1-1/2 in Schedule 40 PVC from it, and step up to 2 in only for a long line or a high sump pump size calculator flow.
Dropping to 1-1/4 in at 16.5 GPM raises the speed to 3.54 ft/s and the head to 11.60 ft. That costs only 0.79 ft at this flow, but the gap widens quickly at higher flows.
What size sump pump pit do I need?
SumpDirect recommends at least 24 in deep and 18 in wide. That basin holds 26.4 gallons and 1.10 gallons per inch, enough for a float band of 8 in or more.
A wider basin is the better fix for short cycling than any change to the sump pump size calculator flow. Moving from 18 in to 24 in with a 12 in band takes a 35 GPM pump from 33 to 59 second runs at 11.0 GPM of inflow.
Can I use this calculator for a crawl space sump pump?
Crawl space pumps follow the same math, usually with less lift. The 4 ft crawl space case above needs 6.6 GPM at 4.26 ft, a light sump pump size calculator duty point that most small pumps cover.
The risk in a crawl space is oversizing. A pump far above 6.6 GPM in a small basin will cycle in seconds, so a smaller pump or a wider float band suits these pits better.
Is a 1/3 HP or 1/2 HP sump pump better?
The better pump is the one whose curve meets your duty point, not the one with more horsepower. A 1/2 HP pump only helps when the 1/3 HP curve falls short of your sump pump size calculator flow at your head.
For the 10 in/min basement at 10.8 ft, a pump delivering 20 GPM gives 59 second runs, while one delivering 50 GPM gives 14. The stronger pump wears out faster on that pit.
What happens if I oversize my sump pump?
An oversized pump drains the float band in seconds and restarts constantly. A 50 GPM pump on 11.0 GPM of inflow in an 18 in basin runs 14 seconds and starts 58.5 times an hour.
Each start heats the motor and wears the switch, so an oversized pump often fails sooner than a matched one. Widen the band, use a larger basin or choose a pump closer to the target flow.
What is a good GPM for a sump pump?
A good GPM is the measured inflow times 1.5 to 2.0, delivered at your total head, the same target a sump pump size calculator online estimate uses. In an 18 in basin, a rise of 5 to 15 in/min puts the 1.5 target between 8.3 and 24.8 GPM.
Roof water changes that range. A 2,000 sq ft roof in a 2 in/hr storm sends 37.4 GPM to the pit, a 56.1 GPM target at 1.5, which few basement pumps deliver.
Do I need a backup sump pump?
A backup matters most when the basin fills fast. At 11.0 GPM of inflow, an empty 18 × 24 in basin holding 26.4 gallons overflows in about 2.4 minutes after the main pump stops.
A 24 in basin of the same depth holds 47.0 gallons and buys about 4.3 minutes. Neither is long enough to get to a failed pump in a storm, which is the case for a second pump or a battery unit beside the main sump pump size calculator choice.
What is total dynamic head on a sump pump?
Total dynamic head is the vertical lift plus the friction in the discharge pipe and fittings at the pump's flow. The 10 in/min basement needs 10.8 ft of sump pump size calculator head, of which 10 ft is lift.
How much head a pump can handle is its shut-off head on the curve, 19.25 ft for the Model 53. Near that limit the flow falls toward zero, so plan for a duty point well below it.
Why does my pump run but the water keeps rising?
The pump's flow at your head is below the inflow. A pump moving 10 GPM against 11.0 GPM coming in loses ground by 1.0 GPM, and the 26.4 gallon basin fills in about 26 minutes.
The fix is a pump with more flow at the same head, less head from a shorter or straighter discharge, or less inflow by moving downspouts away from the foundation.