Trapezoidal Footing Volume Calculator

Updated

Trapezoidal Footing Volume Calculator for sloped column footings. Enter base and top sizes and the heights for the exact concrete volume, yards to order, bags, formwork and weight.

Quick Setup

Set h₁ to 0 for a sloped-only footing with no vertical-sided base.

Base Slab (Bottom Block)
Column Pad and Slope (Top)
Strip Footing Cross-Section
Round Footing (Conical Frustum)
Areas and Height (Frustum)
Quantity, Waste and Weight1 footing, 10% waste, US units
%
lb/ft³
1 Footing, 10% Waste Included
1.81 yd³ Concrete to Order
Equal to 48.95 ft³ of mixed concrete
44.50 ft³ per Footing
Base Slab (V₁)25.00 ft³
Sloped Top (V₂)19.50 ft³
The base slab is L × B × h₁. The sloped top uses the prismoidal formula, which stays exact even when the pad and base are different shapes.
28.8% Less Than a Flat Block
Flat Block Volume62.50 ft³
Concrete Saved18.00 ft³
Compared with a plain block of the same footprint and full height. The slope trims concrete at the outer edges, where bending is lowest.
29.70 ft² Sloped Face Area
Vertical Side Forms20.00 ft²
Face Slope Angle45.0°
Side forms line the base slab edges. Sloped faces are measured along the slope for finishing or top forms, with the pad centered on the base.
3.34 US Tons Placed Weight
80 lb Bags (0.60 ft³)82 Bags
60 lb Bags (0.45 ft³)109 Bags
Weight uses the net volume of every footing. Bag counts include waste and use Quikrete's listed yields, so round up and keep a spare bag.
Step-by-Step WorkingPrismoidal formula
StepWorkingResult
Sizes in ftL 5, B 5, h₁ 1, l 2, b 2, h₂ 1.5ft
Base area A₁L × B = 5 × 525 ft²
Top area A₂l × b = 2 × 24 ft²
Mid area Am(L + l)/2 × (B + b)/2 = 3.5 × 3.512.25 ft²
Base slab V₁A₁ × h₁ = 25 × 125 ft³
Sloped top V₂h₂/6 × (A₁ + 4Am + A₂) = 1.5/6 × (25 + 49 + 4)19.5 ft³
One footing VV₁ + V₂ = 25 + 19.544.5 ft³
Order volumeV × n × (1 + waste) ÷ 27 = 44.5 × 1 × 1.1 ÷ 271.81 yd³
Excel or Sheets=(5*5*1+1.5/6*(5*5+4*3.5*3.5+2*2))*1*1.1/271.81 yd³
Footing DiagramLive dimensions
Both Common Formulas Agree Here
The pad and base are similar rectangles, so the frustum formula h/3 × (A₁ + A₂ + √(A₁A₂)) matches the exact prismoidal result. A pad that is not in proportion to the base needs the prismoidal formula.

Trapezoidal Footing Volume Calculator for Column Footings

A trapezoidal footing is a rectangular base slab with a sloped top that narrows up to the column. The sloped part saves concrete at the edges, but its volume is not a simple length times width times height. The Trapezoidal Footing Volume Calculator works it out exactly, then adds waste, bags and weight.

The Calculation Method menu has four shapes. With Rectangular Pad Footing, enter the base length L and width B, the base slab depth h₁, the top pad length l and width b, and the sloped height h₂. Set h₁ to 0 for a footing that slopes all the way from the ground to the pad, with no vertical-sided base.

Strip (Wall) Footing handles a long footing under a wall, and Round Footing handles a circular base that tapers to a round pad. With Areas and Height, enter the lower area A₁, the upper area A₂ and the sloped height h when you only know areas. The Solve For menu can also run backward, finding the sloped height, the lower area or the upper area from a volume you already have.

The Quantity, Waste and Weight panel sets the number of identical footings, the waste allowance, US or metric results and the concrete unit weight. The default is 150 lb per cubic foot in US units and 2,400 kg per cubic meter in metric, and you can change either.

Trapezoidal Footing Volume Formula

The Trapezoidal Footing Volume Calculator splits the footing into two parts. The base slab is a plain box, so its volume is the base area times the slab depth.

The sloped top is a solid with two parallel rectangular faces, the base area A₁ below and the pad area A₂ above. Its exact volume comes from the prismoidal formula, which also uses the area Am of the slice halfway up.

Here A₁ = L × B, A₂ = l × b and Am = (L + l)/2 × (B + b)/2. Wolfram MathWorld lists this as the prismatoid formula, with the midsection cut halfway between the two parallel faces. The total trapezoidal footing volume is V₁ plus V₂.

Take the default footing, a 5 × 5 ft base 12 in deep with a 2 × 2 ft pad and a 1.5 ft slope. The base slab holds 5 × 5 × 1 = 25 ft³. The midsection is 3.5 × 3.5 = 12.25 ft², so the slope holds 1.5 ÷ 6 × (25 + 49 + 4) = 19.5 ft³.

That makes 44.5 ft³ per footing. With 10% waste the order is 48.95 ft³, or 1.81 yd³. The first card splits the volume into the base slab and the sloped top, and the hero result gives the cubic yards to order for all your footings.

Prismoidal vs Frustum Formula

Many charts use a shorter frustum formula that needs only the two areas. MathWorld gives it for a right pyramidal frustum, a shape whose top and bottom faces are similar, like a square pad on a square base.

When the pad is in proportion to the base, both formulas give the same answer, and the alert in the Trapezoidal Footing Volume Calculator says so. When the pad is a different shape, such as a square pad on a long rectangular base, the frustum formula reads low. The table shows how much for a 1.5 ft slope.

Base L × BPad l × bPrismoidal V₂Frustum V₂Frustum Low By
5 × 5 ft2 × 2 ft19.50 ft³19.50 ft³0%
6 × 4 ft2 × 2 ft19.00 ft³18.90 ft³0.5%
8 × 4 ft2 × 2 ft24.00 ft³23.66 ft³1.4%
6 × 6 ft3 × 1 ft25.50 ft³24.70 ft³3.2%

The error grows as the pad and base drift out of proportion. This is why the prismoidal formula is the one to use for an irregular trapezoid, or any trapezoidal prism with different bases. When it applies, the alert reports the frustum shortfall for your exact sizes.

The Areas and Height method has only the two areas to work with, so it uses the frustum formula and assumes a pad shaped like its base. For a rectangular pad on a base of a different shape, switch to Rectangular Pad Footing and the tool uses the prismoidal formula instead.

Metric Footing in Cubic Meters

Set Results In to Metric and the Trapezoidal Footing Volume Calculator reports cubic meters, square meters and kilograms. The math is the same, with every length in meters.

Take a footing with a 2 × 2 m base 0.3 m deep, a 0.6 × 0.6 m pad and a 0.45 m slope. The base slab holds 1.2 m³. The midsection is 1.3 × 1.3 = 1.69 m², so the slope holds 0.45 ÷ 6 × (4 + 6.76 + 0.36) = 0.834 m³.

The footing needs 2.034 m³ in all, or 2.24 m³ with 10% waste. At 2,400 kg per cubic meter, the placed concrete weighs about 4,880 kg. Enter your mix's own density if your supplier gives a different figure.

Concrete Saved by the Slope

The second card compares your footing with a plain block of the same footprint and full height. The default 5 × 5 ft footing stands 2.5 ft tall in all, so a flat block would hold 62.5 ft³. The sloped footing holds 44.5 ft³, which is 18 ft³ or 28.8% less.

That saving is the reason to slope a footing at all. On a row of identical column footings it adds up fast. Enter the count under Number of Footings, and every result scales to the full set.

If the top you enter matches the base, there is no taper, and the alert says this is a plain rectangular block. For that shape, the Concrete Footing Calculator estimates the concrete and bags for plain footings more directly.

Area of a Trapezoidal Footing

The third card of the Trapezoidal Footing Volume Calculator gives the surface areas you need for forms and finishing. The base slab's vertical sides need side forms equal to the base perimeter times h₁. For the default footing that is 20 × 1 = 20 ft².

Each sloped face is a trapezium, a four-sided shape with two parallel sides. Its area is the average of the two parallel edges times the slant height measured along the slope, not the vertical height.

Here a and b are the base and pad edges on that face, and r is how far the face steps in. For the default footing, r is 1.5 ft and the slant is 2.12 ft. Each face covers (5 + 2) ÷ 2 × 2.12 = 7.42 ft², and the four faces total 29.70 ft².

The card also gives the face slope angle, 45° for the default footing. It assumes the pad sits centered on the base. An off-center pad changes the angles and face areas, but not the concrete volume.

Weight and Concrete Bags

The fourth card turns the net volume into placed weight for every footing you entered. At 150 lb per cubic foot, the default footing weighs 44.5 × 150 = 6,675 lb, or 3.34 US tons. The Concrete Density Calculator finds the unit weight if you have a measured sample.

The card also counts bags with waste included, using QUIKRETE's listed yields of 0.60 ft³ per 80 lb bag and 0.45 ft³ per 60 lb bag. The default footing takes 82 bags of 80 lb mix or 109 bags of 60 lb mix, which is a lot to mix by hand, so price a ready-mix load as well.

To split a site-mixed pour into cement, sand and gravel, use the Concrete Mix Calculator. For the bars in the footing, the Rebar Calculator plans spacing, count and weight.

Trapezoidal Footing Volume With Steps

Used as a trapezoidal footing volume calculator with steps, the tool's Step-by-Step Working table shows every line of the math for your inputs. It lists the sizes in one unit, the base area, the pad area, the midsection, each volume and the waste, so you can check the result by hand or copy it into a report.

If you keep a trapezoidal footing volume calculator in Excel instead, the prismoidal formula simplifies neatly. Four times the midsection equals (L + l) × (B + b), so the whole footing fits in one line.

In Excel, with L, B, h₁, l, b and h₂ in cells B2 to B7, the trapezoidal footing volume formula is =B2*B3*B4+B7/6*(B2*B3+(B2+B5)*(B3+B6)+B5*B6). For the default footing it returns 44.5, matching the tool. The steps table also ends with an Excel or Sheets line already filled with your numbers, waste and conversion to cubic yards.

Solving for Height or Area

In the Trapezoidal Footing Volume Calculator, the Solve For menu works the frustum formula backward when you know the volume. This helps when the concrete is already ordered or the pad size is fixed and you need the slope that fits.

The default sloped part holds 19.5 ft³ between a 25 ft² base and a 4 ft² pad. Ask for the sloped height with those three values and the tool returns 1.5 ft. Ask for the upper area with the volume, lower area and height, and it returns the 4 ft² pad.

This mode also shows the end-area shortcut, h × (A₁ + A₂) ÷ 2, which always reads high. For a 25 ft² base and a 4 ft² pad over 1.5 ft, it gives 21.75 ft³ against the true 19.5 ft³, or 11.5% too much. Areas alone do not fix the side lengths, so in this mode the third card assumes square plans centered on each other. It reports the square sides it used, so you can see the shape behind the face area and slope angle.

Strip Wall Footing Volume

A strip footing runs under a wall, so its section stays the same along its length. In the Trapezoidal Footing Volume Calculator, choose Strip (Wall) Footing and enter the bottom width B, the top width b, the slab depth h₁, the sloped height h₂ and the run length L.

The cross-section is a rectangle with a trapezium on top. Its area is the slab part plus the average of the two widths times the sloped height, and the volume is that area times the length.

The default strip is 2 ft wide at the bottom, 1 ft at the top, with an 8 in slab and a 6 in slope. Its cross-section is 2 × 0.667 + 1.5 × 0.5 = 2.08 ft², so a 50 ft run holds 104.17 ft³. That is 10.7% less than a flat block 2 ft wide and 14 in tall.

This is the same math as the area and volume of a trapezium prism, and it is exact for a straight run, which the alert confirms. The third card gives the sloped faces along both sides and the side and end forms, which run both long edges of the slab plus the two end bulkheads.

Round Footing and Cone Volume

Round Footing takes the base diameter D, the pad diameter d and the two heights. The base slab is a short cylinder, and the sloped top is a cone with its point cut off, so it uses the conical frustum formula with the two radii R and r.

The default round footing is 5 ft across at the base, tapering to 1.5 ft, with a 12 in slab and a 12 in slope. The slab holds 19.63 ft³ and the cone holds 9.10 ft³, for 28.73 ft³ in all. That is 26.8% less than a flat cylinder of the same size.

The third card gives the sloped cone area, 20.58 ft² measured along the slope, the round side form of 15.71 ft² and a cone slope of 29.7°. For round piers formed with a tube, the Sonotube Calculator adds the tube and a flared bell base, and the Concrete Column Calculator covers the column that rises from the footing.