Concrete Density Calculator

Updated

Concrete Density Calculator divides the mass of a sample by its volume to give density in lb/cu ft and kg/m3. It also solves for weight or volume, with rebar and slab weight added.

Quick Setup

Weigh the sample, then enter its volume or its measured dimensions.

Rebar and Slab1% steel, 4 in slab
% of volume
Mass ÷ Volume
150.0 lb/cu ft Concrete Density
8,100 lb ÷ 54 cu ft
2,403 kg/m³ in Metric
Specific Gravity2.403
Weight per Cubic Yard4,050 lb
Specific gravity is the density divided by water at 62.43 lb/cu ft (1,000 kg/m³). A cubic yard holds 27 cu ft, so it weighs 27 times the lb/cu ft figure.
4.2% Over Plain Stone Mix
Nearest MixReinf. Stone (150)
ACI 90 to 135 lb/cu ftAbove
Plain stone concrete is 144 lb/cu ft (2,307 kg/m³) in building-code dead load tables. ACI 318-19 counts 90 to 135 lb/cu ft as lightweight concrete, up from 115 before.
0.494 cu yd per US Ton
A 4 in Slab Weighs50.00 lb/sq ft
One 6 × 12 in Cylinder29.45 lb
Slab weight is the density times the thickness, the dead load on forms or a deck. The cylinder is a standard strength-test size, handy for a scale check.
153.4 lb/cu ft Reinforced
Rebar Steel Content132.3 lb/cu yd
Change From 1% Rebar+2.3%
Steel weighs 490 lb/cu ft (7,850 kg/m³) and replaces the concrete it displaces, so 1% rebar by volume lifts normal-weight concrete by about 2.4%.
Concrete Density ChartCode dead loads
Concretelb/cu ftkg/m³lb/cu yd
Haydite Lightweight901,4422,430
Expanded Slag1001,6022,700
Plain Cinder1081,7302,916
Reinforced Cinder1111,7782,997
Plain Slag1322,1143,564
Reinforced Slag1382,2113,726
Plain Stone or Gravel1442,3073,888
Reinforced Stone1502,4034,050
Formula, Step by StepYour numbers
Density8,100 lb ÷ 54 cu ft = 150 lb/cu ft
Specific gravity150 lb/cu ft ÷ 62.428 = 2.403
With 1% rebar150 lb/cu ft × 0.99 + 490 × 0.01 = 153.4 lb/cu ft
Same Method as the ASTM C138 Test
ASTM C138 measures fresh concrete density this way: the net mass in a measure of known volume, divided by that volume. Cores and cylinders use their measured dimensions.

Concrete Density Calculator Formula

The Concrete Density Calculator divides the mass of a sample by the volume it fills. The same relation runs backward, so the Solve For menu can also find the weight of a pour from a known density, or the volume from a known weight.

In this formula ρ is the density, m is the mass and V is the volume. Mass can be entered in pounds, US tons, kilograms or tonnes. Volume can be entered in cubic yards, cubic feet, cubic meters or liters, and the units do not have to match each other.

The starting entry is 8,100 lb of concrete in 2 cu yd. Two cubic yards is 54 cu ft, and 8,100 divided by 54 gives 150 lb/cu ft. The first card repeats that result as 2,403 kg/m³, with a specific gravity of 2.403 and a weight of 4,050 lb per cubic yard.

The volume does not have to be typed in directly. Set Volume Input to rectangular or cylinder dimensions and the volume is worked out first. A 6 × 12 in test cylinder that weighs 28.6 lb comes out at 145.7 lb/cu ft, which is 2,333 kg/m³.

The Formula, Step by Step panel under the result cards writes out each line with your own numbers. That makes it easy to check the answer by hand, or to copy the working into a test report or a site diary.

Concrete Density in kg/m3 and lb/ft3

Set Units to Metric and the Concrete Density Calculator reports kg/m³ first, with lb/cu ft beside it. One lb/cu ft equals 16.018 kg/m³. The Units menu switches every field between US and metric at once, and each field also has its own unit list. A density can be typed in lb/cu yd, g/cm³ or kN/m³ while the volume stays in cubic meters.

The Concrete Type list and the Concrete Density Chart use eight design values, and the chart highlights the row nearest your result. The last column below is an extra, showing what a 4 in slab of each concrete weighs per square foot.

Concrete typelb/cu ftkg/m³lb/cu yd4 in slab, lb/sq ft
Haydite lightweight901,4422,43030.0
Expanded slag1001,6022,70033.3
Plain cinder1081,7302,91636.0
Reinforced cinder1111,7782,99737.0
Plain slag1322,1143,56444.0
Reinforced slag1382,2113,72646.0
Plain stone or gravel1442,3073,88848.0
Reinforced stone1502,4034,05050.0

These are the minimum design dead loads printed in the ASCE 7 commentary and repeated in state codes such as Massachusetts 780 CMR Appendix G. The same table gives 25 to 50 lb/cu ft for vermiculite and perlite insulating concrete, and 70 to 105 lb/cu ft for other load-bearing lightweight aggregate.

Metric references usually round normal concrete to 2,400 kg/m³ and reinforced concrete to 2,500 kg/m³. Those are 149.8 and 156.1 lb/cu ft. When a specification uses them, choose Custom Density in the type list and type the figure in.

Specific gravity is the density divided by the density of water, which is 1,000 kg/m³ or 62.43 lb/cu ft. To convert specific gravity back to density, multiply by the same number. A specific gravity of 2.4 is 2,400 kg/m³, or 149.8 lb/cu ft.

In metric mode the first card also gives unit weight in kN/m³, the form used in structural load tables. It is the kg/m³ figure times 9.80665, divided by 1,000. A density of 2,403 kg/m³ is a unit weight of 23.56 kN/m³.

The Density field takes kN/m³ as well, so a unit weight from a load table can be typed straight in. A figure of 24 kN/m³ converts to 2,447 kg/m³ and 25 kN/m³ converts to 2,549 kg/m³. Rounding those to 2,400 and 2,500 treats gravity as 10 m/s², which is a 2% shortcut.

1 m3 Concrete Weight in kg

The 1 m³ concrete weight formula is the density formula turned around. Set Solve For to Find Mass or Weight in the Concrete Density Calculator, enter 1 m³ and the density, and the main result is the weight in kilograms.

At 2,400 kg/m³, one cubic meter of concrete weighs 2,400 kg. That is 2.4 tonnes, or about 5,291 lb. With the US code values, a cubic meter of plain stone concrete weighs 2,307 kg and reinforced stone concrete weighs 2,403 kg.

Find Volume answers the reverse question. One tonne of concrete at 2,400 kg/m³ fills 0.417 m³. One US ton at 150 lb/cu ft fills 13.33 cu ft, which is 0.494 cu yd. In density mode the third card shows that cu yd per US ton figure for your own mix. In volume mode the same card shows the area the concrete covers at your slab thickness.

A cubic meter is 1,000 liters, and only water weighs close to 1,000 kg per cubic meter. Normal concrete is about 2.4 times heavier than water, so a cubic meter is never the same thing as a tonne on a concrete job.

Concrete Density Calculator for Slab Weight

The Concrete Density Calculator also works as a concrete weight calculator by dimensions. Choose Find Mass or Weight, pick the concrete type, and set Volume Input to Rectangular Dimensions. Length, width and thickness each take their own unit.

A slab 12 ft long, 9 ft wide and 6 in thick holds 54 cu ft. At 144 lb/cu ft for plain stone concrete it weighs 7,776 lb. The first card shows that as 3.89 US tons and 3,527 kg. An RCC slab quantity is found the same way, since the volume is still length times width times thickness.

The slab row on the third card gives weight per square foot, which is the density times the thickness. A 4 in slab at 150 lb/cu ft weighs 50 lb/sq ft. That is 12.5 lb/sq ft for every inch of reinforced stone concrete and 12 lb/sq ft for plain, the same per-inch loads the Massachusetts table lists. In metric, a 100 mm slab at 2,400 kg/m³ weighs 240 kg/m².

Slab thickness for that row is set in the Rebar and Slab panel, from a thin topping up to 10 ft. The next row gives the weight of one standard test cylinder, 6 × 12 in or 150 × 300 mm, at the same density. It is a quick check for a lab scale.

These weights are for dead loads on forms and decks, crane picks and truck limits. To find how much to order, use the Concrete Calculator. Round piers are covered by the Sonotube Calculator and the Concrete Column Calculator. Unit weight also drives the form loads in the Concrete Pressure Calculator.

RCC Density and Rebar Steel

Steel weighs 490 lb/cu ft, or 7,850 kg/m³, more than three times as much as concrete. Every bar takes the place of the concrete it displaces, so reinforced concrete is always a little heavier than the plain mix around it.

Here p is the share of the volume taken up by steel. The default of 1% lifts a 150 lb/cu ft concrete to 153.4 lb/cu ft. The fourth card also shows the steel content, which is 132.3 lb of rebar in every cubic yard at 1%.

The table below starts from plain stone concrete at 144 lb/cu ft and shows what each steel percentage does to it. The rebar field accepts any value from 0% to 8% of the volume, so heavier sections can be checked the same way.

Rebar by volumelb/cu ftkg/m³Steel, lb/cu yd
0.5%145.72,33466.2
1.0%147.52,362132.3
1.5%149.22,390198.5
2.0%150.92,418264.6
3.0%154.42,473396.9

The code value of 150 lb/cu ft for reinforced stone concrete matches about 1.7% steel in a 144 lb/cu ft mix. The metric RCC figure of 2,500 kg/m³ matches about 1.8% steel in a 2,400 kg/m³ mix. A lightly reinforced slab sits below both, and a heavily reinforced column can sit above.

For the unit weight of RCC per m³, India's dead load code IS 875 Part 1 works the same way as the table above. It lists stone-aggregate reinforced concrete at 2,310 to 2,470 kg/m³ with 1% steel and 2,370 to 2,530 kg/m³ with 2% steel. Plain concrete of the same aggregate is 2,240 to 2,400 kg/m³.

Indian designers often round RCC to 25 kN/m³ and plain concrete to 24 kN/m³ for load calculations. In weight mode the fourth card gives the pounds or kilograms of rebar in the pour. The Rebar Calculator turns a bar layout into the actual steel weight.

Lightweight and Normal-Weight Ranges

The second card compares your result with plain stone concrete at 144 lb/cu ft and names the nearest mix in the code table. The default 150 lb/cu ft reads 4.2% over the plain stone mix. The last row says whether the result is below, inside or above the 90 to 135 lb/cu ft lightweight band, which is 1,442 to 2,162 kg/m³.

ACI 318-14 defined lightweight concrete as having an equilibrium density between 90 and 115 lb/cu ft, as NRMCA TIP 9 explains. ACI 318-19 moved to a density-based rule and treats concrete as normal weight only above 135 lb/cu ft, or 2,160 kg/m³. ASTM C125 now defines low-density concrete as 90 to 135 lb/cu ft.

Equilibrium density is not the fresh density from the truck. It is the density lightweight concrete settles at after it dries in service, found by ASTM C567. NRMCA notes the measured version can take as long as 90 days, so it is normally calculated from the fresh density and the mix data.

A result under 25 lb/cu ft or over 160 lb/cu ft brings up a warning. Most of the time that points to a unit slip, such as grams entered as kilograms or inches entered as feet. Heavyweight shielding mixes made with barite or magnetite aggregate are the real exception above 160 lb/cu ft.

Measuring Density with ASTM C138

ASTM C138 is the standard test for the density of freshly mixed concrete. A measure of known volume is filled, consolidated, struck off flat and weighed. For a rodded sample the concrete goes in as three layers of about equal depth. The net mass of the concrete divided by the volume of the measure is the density.

The NICET checklist for the test has the result reported to the nearest 0.1 lb/cu ft, or 1 kg/m³. To run the same math here, enter the net mass and the measure volume. A 0.25 cu ft measure holding 36.4 lb of concrete gives 145.6 lb/cu ft.

The C138 result also feeds the yield check, which compares the volume a batch really made with the volume on the ticket. The Concrete Yield Calculator takes the same unit weight and the batch weights and returns the relative yield.

Hardened cores and cylinders are done from measured dimensions. Weigh the sample in the moisture condition you want to report, because a wet core reads heavier than the same core after drying. Measure the diameter and length in more than one place and enter the averages.

Is Cement Density 1440 or 3150 kg/m3?

Both numbers are right, and they describe different things. Neither one is the density of concrete, so neither belongs in the density field of the Concrete Density Calculator. Hardened concrete sits between the two, near 2,400 kg/m³.

The 3,150 kg/m³ figure is the density of the cement particles themselves. It matches the specific gravity of 3.15 that Pavement Interactive quotes from the Portland Cement Association, measured by ASTM C188. Mix designers use it to find the absolute volume the cement takes up inside the concrete.

The 1,440 kg/m³ figure is the bulk density of loose cement powder, with the air between the grains included. IS 875 Part 1 lists it as 14.10 kN/m³ for ordinary cement. It is used for bag, bin and batch-box volumes. A 50 kg bag fills about 34.7 liters as loose powder, but the solid cement inside it is only 15.9 liters. US practice counts a 94 lb bag as one cubic foot, which works out to 1,506 kg/m³.

That is why the specific gravity is 3.15 while the bag density is 1,440. For cement bags, sand and gravel in a batch, use the Cement Calculator. Mixing water is handled by the Water To Cement Ratio Calculator.

Density of M20, M25 and 1:2:4 Concrete

An M grade is a strength class, not a density class. The number is the 28-day characteristic compressive strength in N/mm², so M20 is 20 N/mm² and M25 is 25 N/mm². Two mixes of the same grade can have different densities if their aggregates differ.

IS 875 Part 1 gives one density range for stone-aggregate concrete, whatever the grade. Plain M20 or M25 concrete falls at 2,240 to 2,400 kg/m³, and the common working figure is 2,400 kg/m³. With 1% to 2% steel the same concrete runs from about 2,310 to 2,530 kg/m³.

On site, M5, M10, M15 and M20 are tied to the volume mixes 1:5:10, 1:3:6, 1:2:4 and 1:1.5:3 of cement, sand and stone. The 4-2-1 rule is the 1:2:4 mix read from the stone end. IS 456 allows nominal mixes only for M20 and lower, so M25 and above are design mixes.

M20 is the lowest grade IS 456 accepts for reinforced concrete, and only in mild exposure. The minimum rises to M25 for moderate exposure, M30 for severe and M40 for extreme. None of that changes the density much, because the aggregate still makes up most of the weight.

To split a volume into cement, sand, gravel and water for a ratio such as 1:2:4, use the Concrete Mix Calculator. Then bring the batch weight and volume back to the Concrete Density Calculator to check the density the mix really reached.

Concrete Density FAQ

These are the density questions that come up most often once the main result is on the screen. Each answer uses numbers you can reproduce in the tool above by typing in the same mass, volume or density.

How do I calculate the density of concrete?

Weigh the concrete, find the volume it fills, and divide the mass by the volume. A cubic yard that weighs 3,850 lb has a density of 3,850 divided by 27, which is 142.6 lb/cu ft or 2,284 kg/m³. For a core or cylinder, get the volume from the measured diameter and length first.

How do I convert kg to m3 for concrete?

Divide the mass by the density. At 2,400 kg/m³, 1,000 kg of concrete is 0.417 m³ and a single kilogram is 0.000417 m³, a little under half a liter. Going the other way, multiply cubic meters by 2,400 to get kilograms. Find Volume mode in the Concrete Density Calculator does this for any density you enter.

What is the density of RMC?

Ready-mix concrete is a way of supplying concrete, not a separate type. Its density depends on the aggregates and the air content, and normal-weight RMC is usually close to 2,400 kg/m³, or 150 lb/cu ft. The plant's batch ticket lists the weights for your load, and an ASTM C138 test at the truck confirms the figure.

How many kg is 1 bag of cement?

A standard bag is 50 kg in India and most metric markets. A US bag of portland cement is 94 lb, which is 42.6 kg. At a bulk density of 1,440 kg/m³, a 50 kg bag measures about 0.0347 m³, so roughly 29 bags make one cubic meter of loose cement.