555 Monostable Calculator

Updated

555 monostable calculator for one-shot pulse width, or the timing resistor or capacitor for a set delay, with E12 choices, tolerance range, drift, trigger levels and pin 5 control.

555 Monostable

Enter the timing resistor and capacitor. A 555 monostable holds its output high for T = 1.1 × R × C after each trigger.

Supply, Pin 5 & Tolerance--
V
V
%
%
5.17 s Output Pulse Width
T = 1.1 × 100 kΩ × 47 µF
5.163 s Exact (ln 3 × RC)
Time Constant (τ = RC)4.7 s
1.1 Rule Is Long By0.126%
The capacitor charges to 2/3 of VCC, which takes ln 3 = 1.0986 time constants; 1.1 is the rounded rule.
3.929 s to 6.514 s Range
Worst-Case Spread-24% / +26%
Drift per 10 °C Change2.585 ms
Pulse range from the part tolerances, plus the bipolar 555’s 50 ppm/°C and 0.1%/V drift.
3 V Trigger Level (Pin 2)
Threshold (Pin 6)6 V
Reset (Pin 4) Below0.3 V
Pull pin 2 below this level to start the pulse, then let it go high again before the pulse ends.
90 µA Peak Charging Current
Current at Threshold30 µA
Largest Usable R at ±5%5.714 MΩ
The resistor current that charges C; at threshold it must still beat pin 6 and capacitor leakage.
Pulse Waveforms5.17 s high pulse
Pin 2Pin 6Pin 3threshold 6 VT = 5.17 sbelow 3 V
Capacitor Voltage During the Pulse0 to 6 V in 5.163 s
PointTimeCapacitor Voltage% of VCCCharging Current
Trigger0 s0 V0%90 µA
¼ of T1.291 s2.161 V24%68.39 µA
½ of T2.582 s3.804 V42.3%51.96 µA
¾ of T3.873 s5.052 V56.1%39.48 µA
End of pulse5.163 s6 V66.7%30 µA
Step-by-Step Math6 steps
1. Time Constantτ = R × C = 100,000 Ω × 0.000047 F = 4.7 s
2. Pulse WidthT = 1.1 × 4.7 s = 5.17 s
3. Exact ValueT = ln 3 × RC = 1.0986 × 4.7 s = 5.163 s
4. Comparator Levelstrigger 3 V (⅓ VCC), threshold 6 V (⅔ VCC)
5. Tolerance5.17 s × (1 ± 0.05) × (1 ± 0.2)
6. Result5.17 s Output Pulse Width
The Capacitor Sets the Accuracy
With a ±20% capacitor the pulse can land anywhere from 3.929 s to 6.514 s. A film capacitor with a tighter tolerance gives a steadier pulse.

555 Monostable Calculator Formula: 1.1 × R × C and Where It Comes From

A 555 one-shot holds its output high for T = 1.1 × R × C after each trigger. The pulse lasts as long as the timing capacitor takes to charge from 0 V to two-thirds of the supply through R.

T is the pulse width in seconds, R the timing resistor in ohms and C the timing capacitor in farads. Every 555 monostable calculator answer starts from this line. With 10 kΩ and 100 µF, the pulse is 1.1 s.

The 1.1 is ln 3 = 1.0986 rounded up, because charging to two-thirds of the supply takes ln 3 time constants. The rounded rule runs 0.126% long, so a 555 monostable calculator figure of 5.17 s, from 100 kΩ and 47 µF, is really 5.163 s.

The supply voltage drops out of the 555 monostable formula, since the charge target and the threshold both scale with it. In a 555 monostable calculator Excel sheet, the usual value is =1.1*R*C and the exact one is =LN(3)*R*C.

Point in the pulseTimeCapacitor voltageShare of 9 VCharging current
Trigger0 s0 V0%90 µA
¼ of T1.291 s2.161 V24.0%68.39 µA
½ of T2.582 s3.804 V42.3%51.96 µA
¾ of T3.873 s5.052 V56.1%39.48 µA
End of pulse5.163 s6 V66.7%30 µA

The rows use 100 kΩ, 47 µF and a 9 V supply. The voltage climb slows as the capacitor fills, and the current through R falls from 90 µA to 30 µA by the time the threshold trips.

That 30 µA end-of-pulse current is the number to watch in any 555 monostable calculator result with a large R. It has to beat the threshold pin's input current and the capacitor's own leakage, or the pulse never ends.

Delay Grid for Common Resistor and Capacitor Values

Every tenfold step in R or in C makes the pulse ten times longer. One 555 monostable calculator grid of five capacitors and four resistors spans 11 µs to almost two minutes.

R \ C10 nF100 nF1 µF10 µF100 µF
1 kΩ11 µs110 µs1.1 ms11 ms110 ms
10 kΩ110 µs1.1 ms11 ms110 ms1.1 s
100 kΩ1.1 ms11 ms110 ms1.1 s11 s
1 MΩ11 ms110 ms1.1 s11 s1.833 min

The 1 kΩ and 10 nF corner, 11 µs, sits just above the 10 µs floor a bipolar 555 can time reliably. Same-delay pairs along each diagonal are not equal choices: a smaller C with a larger R saves board space but feeds less current.

The longest cells in the grid are the ones most at risk from capacitor leakage, since the charging current near the threshold is smallest there. At 1 MΩ and 9 V, only 3 µA is left to charge the capacitor.

E12 Parts for a Target Pulse Width

To turn a target delay into parts, run the 555 monostable calculator math backwards and solve for the resistor. Fix the capacitor first, since capacitors come in fewer values and wider tolerances than resistors.

T is the wanted pulse in seconds and C the capacitor you have in farads. The capacitor version swaps the two, C = T ÷ (1.1 × R), and works the same way with a fixed resistor.

Target pulseCapacitorExact RE12 belowPulse with itE12 abovePulse with it
1 ms22 nF41.32 kΩ39 kΩ943.8 µs47 kΩ1.137 ms
10 ms100 nF90.91 kΩ82 kΩ9.02 ms100 kΩ11 ms
100 ms2.2 µF41.32 kΩ39 kΩ94.38 ms47 kΩ113.7 ms
1 s4.7 µF193.4 kΩ180 kΩ930.6 ms220 kΩ1.137 s
10 s33 µF275.5 kΩ270 kΩ9.801 s330 kΩ11.98 s
1 min470 µF116.1 kΩ100 kΩ51.7 s120 kΩ1.034 min

Rounded to E12, a 555 monostable calculator resistor misses its target by 2% to 20% here. Where that matters, put a fixed resistor in series with a trimmer, or use the E24 or E96 series, which step about every 10% and 2.4%.

Why C should come first is clear from the 555 monostable calculator math for the capacitor. A 1 s pulse from 100 kΩ needs 9.091 µF; the stock 8.2 µF gives 902 ms and 10 µF gives 1.1 s, a 10% miss either way.

Accuracy of a 555 Timer Pulse Comes From the Parts

A 555 one-shot is only as precise as its capacitor. On a 5.17 s 555 monostable calculator design, a ±5% resistor and a ±20% electrolytic let the pulse land anywhere from 3.929 s to 6.514 s.

Resistor toleranceCapacitor toleranceShortest pulseLongest pulseSpread
±5%±20%3.929 s6.514 s-24% / +26%
±1%±20%4.095 s6.266 s-20.8% / +21.2%
±1%±10%4.606 s5.744 s-10.9% / +11.1%
±1%±5%4.862 s5.483 s-5.95% / +6.05%
±1%±2%5.016 s5.326 s-2.98% / +3.02%

Upgrading the resistor from ±5% to ±1% narrows the spread by only about 4 points on each side. Moving the capacitor from ±20% to ±5% cuts about 15 points per side, which is why tight film capacitors matter more than precision resistors.

The timer chip adds far less. The TI NE555 datasheet lists 50 ppm/°C and 0.1%/V typical monostable drift, which works out to 2.585 ms per 10 °C and 5.17 ms per volt on a 5.17 s pulse.

The SE555 grade halves that, at 30 ppm/°C and 0.05%/V, or 1.551 ms per 10 °C and 2.585 ms per volt on the same 5.17 s pulse.

TI has dropped the initial timing-error figure from current revisions of both the bipolar and CMOS datasheets, so measure a prototype when the first pulse must match the 555 monostable calculator value.

Trigger, Threshold and Reset Levels at Common Supplies

Pulling pin 2 below one-third of the supply starts the pulse, and the pulse ends when pin 6 reaches two-thirds. Pin 4 resets the timer when it drops below 0.3 V.

SupplyTrigger belowThresholdNE555 trigger rangeCurrent at threshold, 1 MΩ
5 V1.667 V3.333 V1.1 V to 2.2 V1.667 µA
9 V3 V6 VNot listed3 µA
12 V4 V8 VNot listed4 µA
15 V5 V10 V4.5 V to 5.6 V5 µA

Trigger levels in a 555 monostable calculator are nominal, and the datasheet ranges show why a trigger that only dips to one-third is risky. At 5 V, drive pin 2 below 1.1 V to fire every part; at 15 V, below 4.5 V.

The trigger must also come back up before the pulse ends. TI requires pin 2 high for at least 10 µs before the end on the NE555, and 1 µs on the CMOS TLC555.

Hold the trigger low longer and the output simply stays high until it is released. A button held for 2 s on a 1.1 s timer gives a pulse of about 2 s, so feed long triggers through a small series capacitor that passes only the falling edge.

Triggers that arrive mid-pulse are ignored, since TI notes the 555 cannot retrigger during the timing cycle. Reset is guaranteed only below 0.3 V; the NE555 can need anything from 0.3 V to 1 V, so tie pin 4 to the supply when it is unused.

Pin 5 Control Voltage Replaces the 1.1 Constant

Driving pin 5 sets the threshold to that voltage and the trigger to half of it, which takes the 555 monostable calculator beyond the fixed 1.1 rule. The 1.1 multiplier then changes with the ratio of pin 5 voltage to supply.

Vc is the voltage on pin 5 and VCC the supply. With pin 5 left open, Vc sits at two-thirds of VCC and the multiplier returns to ln 3, or 1.0986.

Pin 5 voltage (9 V supply)Trigger levelMultiplier kPulse with 100 kΩ, 47 µF
3 V1.5 V0.40551.906 s
4.5 V2.25 V0.69313.258 s
6 V (open)3 V1.0995.163 s
7 V3.5 V1.5047.069 s
8 V4 V2.19710.33 s
8.5 V4.25 V2.89013.58 s

The response bends sharply near the supply: the last half volt, 8 V to 8.5 V, adds 3.25 s. A 555 timer PWM calculator setup uses exactly this effect, swinging pin 5 to modulate the width of each pulse.

The same math explains part-to-part spread. TI allows the open pin 5 voltage to sit anywhere from 9 V to 11 V on a 15 V NE555, which would move a pulse between 0.83 and 1.20 times the 555 monostable calculator value at the extremes.

Typical parts sit near 10 V, but a 10 nF capacitor from pin 5 to ground keeps supply noise off this node. That bypass belongs in every 555 monostable calculator circuit, even when nothing else connects to pin 5.

Capacitor Leakage Stretches Long Delays

Leakage acts as a steady drain on the timing capacitor, so it charges toward a lower voltage and takes longer to reach the threshold. If that lower voltage never reaches two-thirds of the supply, the pulse never ends.

Vp is the voltage the capacitor heads toward, Ileak the leakage current from the capacitor's datasheet and Vth the threshold, two-thirds of VCC. With no leakage this returns to ln 3 × RC, the plain 555 monostable calculator result.

Leakage100 kΩ, 47 µFChange vs 5.17 s1 MΩ, 100 µFChange vs 110 s
None5.163 s-0.13%109.9 s-0.13%
0.1 µA5.174 s+0.08%112.1 s+1.9%
0.5 µA5.216 s+0.9%122.4 s+11.3%
1 µA5.270 s+1.9%138.6 s+26%
2 µA5.382 s+4.1%194.6 s+76.9%
3 µA5.499 s+6.4%Never ends-

Both designs in this 555 monostable calculator comparison run on 9 V. The same 3 µA that adds 6.4% to the 100 kΩ design stops the 1 MΩ design outright, because 3 µA is all the current R can supply at the threshold.

Keep leakage small next to the current R delivers at the threshold. At one-thirtieth of it, 0.1 µA against 3 µA, the pulse runs 1.9% long; at one-third it runs 26% long.

Take the leakage figure from the capacitor maker's datasheet rather than a rule of thumb, since limits vary widely by series. Film and tantalum parts leak far less than general-purpose electrolytics.

Largest Timing Resistor and Shortest Pulse

On a bipolar NE555, keep a 555 monostable calculator resistor below about 3.4 MΩ at 5 V and 10 MΩ at 15 V, as TI advises. Above that, the threshold pin's input current of up to 250 nA can stop the capacitor from ever reaching two-thirds.

SupplyCurrent at threshold, 10 MΩR where current equals 250 nATI suggested maximumLargest ±5% R, 500 nA rule
5 V166.7 nA6.667 MΩAbout 3.4 MΩ3.175 MΩ
9 V300 nA12 MΩNot listed5.714 MΩ
12 V400 nA16 MΩNot listed7.619 MΩ
15 V500 nA20 MΩAbout 10 MΩ9.524 MΩ

TI's figures match a 500 nA allowance, twice the 250 nA worst case, which leaves a 2:1 margin. At 5 V a 10 MΩ resistor delivers only 166.7 nA at threshold, below what the pin may draw, so the pulse can hang.

Size any 555 monostable calculator resistor limit for the top of its tolerance. A ±5% part marked 3.3 MΩ can measure 3.465 MΩ, so at 5 V the safe nominal value is 3.175 MΩ.

Leakage cuts the limit further. Add 1 µA of capacitor leakage at 9 V and the ±5% limit falls from 5.714 MΩ to 1.905 MΩ.

The CMOS TLC555 draws 10 pA typical and 75 pA maximum at the threshold pin. With it, capacitor and board leakage set the limit instead. The TLC555 family runs from 2 V to 15 V, though TI rates the TLC555I from 3 V and the M and Q grades from 5 V.

The short end is set by the trigger rule: 10 µs on the NE555 and 1 µs on the TLC555. A 10 µs pulse needs RC of 9.091 µs, such as 9.091 kΩ with 1 nF, and stray capacitance starts to matter at that size.

One-Shot Timing in Everyday 555 Circuits

Most 555 monostable calculator questions come back to three facts: it has one stable state, it ignores triggers while timing, and its pulse is set by R and C alone.

What is a 555 monostable calculator?

It is the 1.1 × R × C relation solved for whichever value is missing: the pulse from R and C, or the R or C for a wanted pulse. A 500 ms delay with 4.7 µF, for example, needs 96.71 kΩ.

The 555 monostable circuit diagram behind those numbers is simple. R runs from the supply to pins 6 and 7, C from that node to ground, pin 2 takes the trigger, pin 3 gives the pulse, pin 4 goes to the supply and pin 5 gets a 10 nF bypass.

How do I use a 555 timer calculator?

Start from the value the job fixes, usually the delay, then the capacitor you can buy, and solve for the resistor. Round to a stock resistor and recheck the pulse with that part.

Unit slips cause most wrong answers. Using 47 nF where 47 µF was meant turns a 5.17 s pulse into 5.17 ms, a factor of 1,000, so read the prefix on the capacitor body before trusting any 555 timer calculator result.

What does a monostable circuit do?

A monostable sits in one stable state, output low, until a trigger arrives. It then drives the output high for a fixed time, ignores further triggers, and drops back low on its own.

With 100 kΩ and 47 µF on 9 V, a dip of pin 2 below 3 V starts a 5.17 s high pulse. That makes it a delay, a timed relay driver or a debounce for a noisy switch.

What is the difference between monostable mode and astable mode in 555 timer circuits?

Monostable gives one pulse per trigger; astable has no stable state and oscillates on its own. An astable adds a second resistor and runs at about f = 1.44 ÷ ((RA + 2RB) × C), so 10 kΩ, 10 kΩ and 10 µF give 4.8 Hz.

TI rates astable drift at 150 ppm/°C against 50 ppm/°C for monostable on the NE555, so one-shots hold time better. For the free-running case, the 555 Timer Astable Oscillator Circuit covers the two-resistor math.

The third common mode, bistable, uses trigger and reset as set and clear. With pins 2 and 6 tied, the chip also works as an inverting Schmitt trigger; the Schmitt Trigger Calculator handles that kind of hysteresis design.

What is the maximum frequency of a 555 timer?

TI advises keeping the bipolar NE555 at 100 kHz or below to limit distortion. The CMOS TLC555 is rated up to 2.1 MHz typical in astable mode.

In monostable use, any 555 monostable calculator pulse also caps the trigger rate at 1 ÷ T. A 5.17 s pulse allows at most one trigger every 5.17 s, or 0.193 Hz, and the 10 µs minimum pulse caps a bipolar one-shot near 100 kHz.

What are the applications of 555 timer?

Delays, timed relays, switch debouncing, missing-pulse detection, tone and LED flashers, and pulse-width modulation are the usual jobs. Monostable mode covers anything that needs one fixed-length pulse per event.

A hobby servo tester is a good 555 monostable calculator example. Servos expect 1 ms to 2 ms pulses, which a 100 nF capacitor gives with 9.091 kΩ and 18.18 kΩ, so a 9.1 kΩ resistor plus a 10 kΩ pot spans 1.001 ms to 2.101 ms.