Notch filter calculator for passive and active twin-T, wideband, LC tank and trap, speaker resonance and digital biquad notches, with Q, -3 dB width and depth from parts tolerance.
--
Test Signal & Real Parts
Circuit With Your Values
Frequency Response Curve
Response at Key Frequencies
| Frequency | Gain | Cut | Output (1 V In) | Phase |
|---|---|---|---|---|
| 15 Hz | 0.9986 V/V | -0.0123 dB | 998.6 mV | -3.053° |
| 30 Hz | 0.9912 V/V | -0.0765 dB | 991.2 mV | -7.595° |
| 54.3 Hz (-3 dB) | 0.7071 V/V | -3.01 dB | 707.1 mV | -45° |
| 60 Hz (f₀) | 0 V/V | Total | 0 V | ±90° flip |
| 66.3 Hz (-3 dB) | 0.7071 V/V | -3.01 dB | 707.1 mV | 45° |
| 120 Hz (your test) | 0.9912 V/V | -0.0765 dB | 991.2 mV | 7.595° |
| 240 Hz | 0.9986 V/V | -0.0123 dB | 998.6 mV | 3.053° |
Parts for Mains Hum and Harmonics
| Notch | Use | C₁ = C₂ (R = 22 kΩ) | C₃ = 2C |
|---|---|---|---|
| 50 Hz | 50 Hz mains | 144.7 nF | 289.4 nF |
| 60 Hz | 60 Hz mains | 120.6 nF | 241.1 nF |
| 100 Hz | 2nd harmonic, 50 Hz | 72.34 nF | 144.7 nF |
| 120 Hz | 2nd harmonic, 60 Hz | 60.29 nF | 120.6 nF |
| 150 Hz | 3rd harmonic, 50 Hz | 48.23 nF | 96.46 nF |
| 180 Hz | 3rd harmonic, 60 Hz | 40.19 nF | 80.38 nF |
Step-by-Step Math
Twin-T Notch Filter Calculator Values for 50 Hz and 60 Hz Hum
A twin-T notch nulls one frequency set by a single resistor value and a single capacitor value. It uses two series resistors R, two series capacitors C, a shunt resistor R/2 and a shunt capacitor 2C.
R is each series resistor in ohms and C each series capacitor in farads, with R/2 and 2C in the shunt legs. In twin-T notch filter calculator terms, 22 kΩ at 60 Hz needs C = 120.6 nF and a 241.1 nF shunt capacitor.
| Notch | Target | C₁ = C₂ with 22 kΩ | C₃ = 2C | Nearest E12 C | Notch with E12 C |
|---|---|---|---|---|---|
| 50 Hz | 50 Hz mains | 144.7 nF | 289.4 nF | 150 nF | 48.23 Hz |
| 60 Hz | 60 Hz mains | 120.6 nF | 241.1 nF | 120 nF | 60.29 Hz |
| 100 Hz | 2nd harmonic, 50 Hz | 72.34 nF | 144.7 nF | 68 nF | 106.4 Hz |
| 120 Hz | 2nd harmonic, 60 Hz | 60.29 nF | 120.6 nF | 56 nF | 129.2 Hz |
| 150 Hz | 3rd harmonic, 50 Hz | 48.23 nF | 96.46 nF | 47 nF | 153.9 Hz |
| 180 Hz | 3rd harmonic, 60 Hz | 40.19 nF | 80.38 nF | 39 nF | 185.5 Hz |
Stock values move a notch filter calculator result more than people expect. The 120 Hz row lands at 129.2 Hz with a 56 nF part, well off a narrow notch, so build exact values from parallel pairs or trim R instead.
Watch the labeling when comparing sources. Some quote f₀ = 1 ÷ (4πRC) because they call the shunt resistor R and the series resistors 2R. Plug the 22 kΩ and 120.6 nF above into that form and you get 30 Hz, half the real notch.
Passive Twin-T vs Active Twin-T: Q Sets the Width
A passive twin-T has a fixed Q of 0.25, so its -3 dB band spans 4 × f₀. Feeding back a fraction k of the output to the shunt node raises Q to 1 ÷ (4(1 - k)).
k is the share of the output fed back to the R/2 and 2C junction, usually from a divider and buffer. Q is f₀ divided by the -3 dB width, so Q 5 at 60 Hz needs k = 0.95.
| Q | k | Ra with Rb 10 kΩ | -3 dB edges | 20 dB wide | Loss at 50 Hz | Loss at 120 Hz |
|---|---|---|---|---|---|---|
| 0.25 (passive) | 0 | - | 14.16 to 254.2 Hz | 24.12 Hz | -20.8 dB | -9.09 dB |
| 1 | 0.75 | 3.333 kΩ | 37.08 to 97.08 Hz | 6.03 Hz | -9.26 dB | -1.6 dB |
| 2 | 0.875 | 1.429 kΩ | 46.85 to 76.85 Hz | 3.015 Hz | -4.56 dB | -0.458 dB |
| 5 | 0.95 | 526.3 Ω | 54.3 to 66.3 Hz | 1.206 Hz | -1.13 dB | -0.0765 dB |
| 10 | 0.975 | 256.4 Ω | 57.07 to 63.07 Hz | 0.603 Hz | -0.312 dB | -0.0193 dB |
| 25 | 0.99 | 101 Ω | 58.81 to 61.21 Hz | 0.2412 Hz | -0.0514 dB | -0.0031 dB |
| 50 | 0.995 | 50.25 Ω | 59.4 to 60.6 Hz | 0.1206 Hz | -0.0129 dB | -0.0008 dB |
All rows are a 60 Hz notch filter calculator design with 22 kΩ. The passive version takes 20.8 dB off a 50 Hz signal and 9.09 dB off 120 Hz, so it is a poor choice when nearby audio must survive. Q 5 cuts those losses to 1.13 dB and 0.0765 dB.
The catch is the deep part. The band that is cut by 20 dB or more shrinks from 24.12 Hz at Q 0.25 to 1.206 Hz at Q 5 and 0.1206 Hz at Q 50, so a high-Q notch removes hum only if the hum stays exactly on frequency.
Q above 50 puts k within 0.5% of 1, where part drift can tip the loop into oscillation. An active notch filter calculator result in the Q 2 to 10 range is the practical middle ground for mains hum.
Slow op-amps widen the notch filter calculator width but cannot fill the null. Buffers with 10 kHz of gain-bandwidth widen the Q 5, 60 Hz notch from 12 Hz to 13.3 Hz, and 3 kHz widens it to 22.89 Hz; 1 MHz parts change it by under 0.01 Hz.
The null stays complete in every case. At f₀ the twin-T output is zero, so the feedback drive is zero too, and buffer lag has nothing to act on. Part mismatch, not the op-amp, sets the real depth.
Extra stages at 2f₀ and 3f₀ extend a twin-T notch filter calculator design to hum harmonics. With Q 5 stages at 60, 120 and 180 Hz, a 90 Hz signal loses 0.802 dB and 150 Hz loses 1.95 dB, against 0.243 dB and 0.0392 dB with the 60 Hz stage alone.
Part Tolerance Decides the Real Notch Depth
An ideal notch filter calculator null is infinitely deep, but one part off by 1% limits a passive notch to about -54 dB and a Q 5 notch to -27.9 dB. Higher Q makes the null far more sensitive to mismatch.
| Worst single part off by | Passive, Q 0.25 | Active, Q 5 | Active, Q 25 | Q 5 null moves by |
|---|---|---|---|---|
| 0.1% | -74.1 dB | -48 dB | -34 dB | ±0.04% |
| 0.5% | -60.1 dB | -34 dB | -19.8 dB | ±0.19% |
| 1% | -54 dB | -27.9 dB | -13.6 dB | -0.37% to +0.38% |
| 2% | -47.9 dB | -21.7 dB | -6.96 dB | -0.74% to +0.76% |
| 5% | -39.7 dB | -13.4 dB | +1.62 dB | -1.82% to +1.95% |
At Q 25 with 5% parts, the response at f₀ is +1.62 dB: the notch has moved off frequency and there is no cut left at all. Narrow notches need parts matched far tighter than their marked tolerance.
In the 60 Hz, 22 kΩ design, a low C₂ hurts most of the six parts. A trimmer in the R/2 leg lets you tune the null back after assembly, which beats buying 0.1% capacitors.
This is why any passive notch filter design calculator result should be read as a starting point. Measure the finished notch, then trim; the twin-T notch filter calculator math only guarantees the null with perfect parts.
Wideband Notch From a Low-Pass and a High-Pass
A wideband notch adds a low-pass output to a high-pass output, and everything between the two corners is cut. The depth at the center, √(flow × fhigh), depends only on how far apart the corners sit.
flow is the low-pass corner and fhigh the high-pass corner, both first-order. Analog Devices' filter chapter notes this approach suits corners more than an octave apart.
| Upper ÷ lower corner | Depth at center | Center with a 300 Hz low-pass corner |
|---|---|---|
| 1.83× | -3.02 dB | 405.8 Hz |
| 5× | -9.54 dB | 670.8 Hz |
| 20× | -20.4 dB | 1.342 kHz |
| 100× | -34.1 dB | 3 kHz |
| 199× | -40 dB | 4.232 kHz |
| 1000× | -54 dB | 9.487 kHz |
Depth and width come together here: a 40 dB wideband notch filter calculator design needs corners 199× apart. With 4.7 nF, corners at 300 Hz and 30 kHz need 112.9 kΩ and 1.129 kΩ and give -34.1 dB at 3 kHz.
That 300 Hz to 30 kHz design is still 11.8 dB down at 1 kHz and 10.8 dB down at 10 kHz, so a wideband notch shapes a whole region.
Size each corner with the Low Pass Filter Calculator and High Pass Filter Calculator, then sum them as in the Inverting Op Amp Calculator.
LC Notch Filter Calculator Math: Tank vs Trap
An LC notch sits at f₀ = 1 ÷ (2π√(LC)) in both forms, but Q runs the opposite way. A parallel tank in the signal path has Q = R√(C/L); a series trap to ground has Q = √(L/C) ÷ R.
L is the inductance and C the capacitance. For the tank, R is the source plus the load, Rs + RL; for the trap, it is Rs and RL in parallel. In LC notch filter calculator terms, 2.2 µH with 100 pF notches at 10.73 MHz with √(L/C) = 148.3 Ω.
| Resistance R | Tank Q | Tank -3 dB width | Trap Q | Trap -3 dB width |
|---|---|---|---|---|
| 25 Ω | 0.169 | 63.66 MHz | 5.933 | 1.809 MHz |
| 50 Ω | 0.337 | 31.83 MHz | 2.966 | 3.617 MHz |
| 100 Ω | 0.674 | 15.92 MHz | 1.483 | 7.234 MHz |
| 150 Ω | 1.011 | 10.61 MHz | 0.989 | 10.85 MHz |
| 300 Ω | 2.023 | 5.305 MHz | 0.494 | 21.7 MHz |
| 600 Ω | 4.045 | 2.653 MHz | 0.247 | 43.41 MHz |
With 50 Ω on both sides, the tank sees R = 100 Ω and Q 0.674, while the trap sees 25 Ω and Q 5.933. For a sharper tank, lower the L/C ratio, since small L and large C raise R√(C/L).
Both forms also lose 6.02 dB in the passband to the 50 Ω source and load divider. Measure any RF notch filter calculator cut against that -6.02 dB level, not against the input.
Coil resistance sets the real depth. With 0.2 Ω of coil DCR the coil Q is 741.6, so the 50 Ω trap reaches -42 dB and the tank -60.8 dB. A 40 dB notch needs coil Q above 587.4 for the trap and 66.7 for the tank.
The parts also carry stress at f₀. A 1 V source drives 2.943 V across the trap's capacitor, and 6.736 mA circulates in both the tank's L and its C, so rate the parts for the signal level.
Speaker Series Notch at Driver Resonance
A series C, L and R across a driver flattens its impedance peak at resonance. For a driver with Re 3 Ω, fs 436 Hz, Qes 0.54 and Qms 2.5, the parts are 225.3 µF, 591.4 µH and 3.648 Ω.
Re is the voice-coil DC resistance, fs the resonance and Qes and Qms the electrical and mechanical Q from the driver's data sheet. The network is the mirror image of the driver's motional circuit.
| Frequency | Driver alone | Driver with notch | Notch branch |
|---|---|---|---|
| 109 Hz | 3.48 Ω | 3 Ω | 7.086 Ω |
| 218 Hz | 5.229 Ω | 3 Ω | 4.383 Ω |
| 348.8 Hz | 11.44 Ω | 3 Ω | 3.72 Ω |
| 436 Hz | 16.89 Ω | 3 Ω | 3.648 Ω |
| 545 Hz | 11.44 Ω | 3 Ω | 3.72 Ω |
| 872 Hz | 5.229 Ω | 3 Ω | 4.383 Ω |
| 1.744 kHz | 3.48 Ω | 3 Ω | 7.086 Ω |
The 16.89 Ω peak drops to a flat 3 Ω across the whole range, ignoring voice-coil inductance. That matters most in the notch filter calculator crossover case, where a passive crossover in front of the driver assumes a steady load.
The resistor works hard. At 50 W into the 3 Ω coil, a steady tone at fs puts 41.1 W into the notch resistor and 5.44 V across the capacitor, so a speaker notch filter calculator figure must be rated for that worst case.
Coil resistance counts toward R. With a 0.2 Ω inductor, the resistor to buy is 3.448 Ω, and the capacitor must be a bipolar or film type, never a polarized electrolytic.
If the coil's DCR alone exceeds the notch resistor, the peak cannot be fully flattened. A driver with Re 4 Ω, fs 100 Hz, Qes 0.5 and Qms 2 needs 5 Ω; a 10 Ω coil leaves 6.667 Ω at fs, against 20 Ω with no notch.
Digital Biquad Notch Coefficients
Digital notch filter calculator coefficients follow the biquad from Robert Bristow-Johnson's Audio EQ Cookbook. For 60 Hz, Q 5 and 48 kHz, the normalized coefficients are b₀ = b₂ = 0.99921523, b₁ = a₁ = -1.99836882 and a₂ = 0.99843045.
Fs is the sample rate. The cookbook sets b₀ = b₂ = 1, b₁ = a₁ = -2cos ω₀, a₀ = 1 + α and a₂ = 1 - α, then divides all by a₀ so the filter runs with a₀ = 1.
| Sample rate | b₀ = b₂ | b₁ = a₁ | a₂ | Pole radius |
|---|---|---|---|---|
| 8 kHz | 0.99531144 | -1.98841304 | 0.99062288 | 0.99530040 |
| 16 kHz | 0.99764956 | -1.99474529 | 0.99529912 | 0.99764679 |
| 44.1 kHz | 0.99914589 | -1.99821876 | 0.99829177 | 0.99914552 |
| 48 kHz | 0.99921523 | -1.99836882 | 0.99843045 | 0.99921492 |
| 96 kHz | 0.99960746 | -1.99919950 | 0.99921491 | 0.99960738 |
| 192 kHz | 0.99980369 | -1.99960352 | 0.99960738 | 0.99980367 |
A low notch at a high sample rate pushes the poles toward the unit circle: 0.9998 at 192 kHz. Coefficients that close to 1 need 32-bit float or wider, which matters for a programmable notch filter on a small DSP.
The digital width also drifts at high f₀. A 1 kHz, Q 5 notch at 8 kHz has -3 dB edges at 913.3 Hz and 1.093 kHz, an effective Q of 5.56, because the bilinear transform warps frequencies near half the sample rate.
Notch Filter Basics, Answered With Numbers
Every notch filter calculator result comes down to two numbers: where the null sits, and how wide the cut is, which Q sets as f₀ divided by the -3 dB width.
What is a notch filter?
A notch filter is a narrow band-stop filter that removes one frequency and passes the rest. A Q 5 notch at 60 Hz takes 60 Hz hum to zero in theory while 120 Hz passes almost untouched, at -0.0765 dB.
It is the opposite of a band-pass filter, which keeps a band and rejects the rest; the Bandpass Filter Calculator handles that case. At the notch, the phase jumps from -90° just below f₀ to +90° just above.
What is a notch filter calculator?
It solves the notch equations for whichever value is missing: the capacitor or resistor for a target frequency, or the frequency from parts you have. A 50 Hz twin-T with 22 kΩ, for example, needs 144.7 nF and 289.4 nF.
A general filter calculator usually stops at low-pass and high-pass corners. Worked notch filter calculator steps go further, to the width, the depth with real part tolerance, and the response at the frequencies you need to keep.
What is a wideband notch filter calculator?
It sizes the low-pass and high-pass pair whose summed outputs cut a wide band. Each corner uses R = 1 ÷ (2πfC), so with 10 nF, corners at 1 kHz and 10 kHz need 15.92 kΩ and 1.592 kΩ.
That 10× spacing centers the cut at 3.162 kHz with a depth of only -14.8 dB. Wideband notches trade depth for width, so they suit tone shaping more than removing a single interfering frequency.