Cabinet Door Calculator

Updated

Cabinet door calculator for face-frame overlay, inset and frameless doors, with door size, shaker rails, stiles and panel, door weight, hinge count, plus the lumber and sheet cost.

Cabinet Opening & Door Mounting

Measure the face-frame opening, or the outside of the box for frameless cabinets.

in
in
in
in
in
in
in
in
Door Style, Stiles, Rails & PanelSingle panel, 2 1/4 in frame
in
in
in
in
in
Wood, Quantity & PricesRed Oak, 6 doors
%
lb/ft³
$/ft
Cabinet Door Size, Overlay
15 7/16 × 25 in Each Door
Exact 15.4375 × 25 in, pair spans 31 in, opening + 2 × overlay
2 Rails at 11 11/16 in per Door
Stiles per DoorTwo at 25 in
Total Frame Stock36.69 ft, 24 pieces
Rails run between the stiles plus a stub tenon at each end equal to the groove depth. Stiles run the full door height.
11 9/16 × 21 1/8 in Panel
Panel Opening10 15/16 × 20 1/2 in
Panel Stock1 sheet, 32% used
The panel fills the opening plus both groove depths, less the expansion gap per side so it can move with humidity.
12 Hinges, 2 per Door
Door Weight4.6 lb each
Load per Hinge2.3 lb
Hinge count follows the maker chart by door weight and height, plus one more for doors wider than 23 5/8 in.
$107.76 Material Cost
Frame Lumber8.12 bd ft
Cost per Door$17.96
Frame stock is priced in board feet of 4/4 rough lumber with the waste allowance. Panels come from 4 × 8 sheets.
Cabinet Door Diagram15 7/16 × 25 in
Pair: 15 7/16 in × 25 in each, 1/8 in center gapStiles and rails 2 1/4 in wide, panel 11 9/16 in × 21 1/8 in
Cut List & Hardware6 doors
PartQtySizeNotes
Stile122 1/4 × 25 in3/4 in thick
Rail122 1/4 × 11 11/16 in3/4 in thick
Panel611 9/16 × 21 1/8 in1/4 in thick
Concealed hinge1235 mm cup (1 3/8 in)2 per door
Door pull or knob6-one per door
Overlay vs Inset Door Sizes3 styles
Mount StyleEach DoorRail LengthPanel
Inset, 1/16 in gap14 7/8 × 23 7/8 in11 1/8 in11 × 20 in
Lipped, 3/8 in rabbet (1/4 per side)15 3/16 × 24 1/2 in11 7/16 in11 5/16 × 20 5/8 in
Partial, 1/2 in overlay15 7/16 × 25 in11 11/16 in11 9/16 × 21 1/8 in
Stile and Rail Width Options2 1/4 in selected
Stile and Rail WidthRail LengthPanelDoor Weight
1 3/4 in12 11/16 in12 9/16 × 22 1/8 in4.2 lb
2 in12 3/16 in12 1/16 × 21 5/8 in4.4 lb
2 1/4 in11 11/16 in11 9/16 × 21 1/8 in4.6 lb
2 1/2 in11 3/16 in11 1/16 × 20 5/8 in4.8 lb
3 in10 3/16 in10 1/16 × 19 5/8 in5.2 lb
Step-by-Step Door Math8 steps
Door width(30 + 2 × 0.5 - 0.125) ÷ 2 = 15.4375 in
Door height24 + 2 × 0.5 = 25 in
Rail length15.4375 - 2 × 2.25 + 2 × 0.375 = 11.6875 in
Panel width(15.4375 - 2 × 2.25) + 2 × 0.375 - 2 × 0.0625 = 11.5625 in
Panel height(25 - 2 × 2.25) + 2 × 0.375 - 2 × 0.0625 = 21.125 in
Board feet165.0938 cu in (at 4/4) ÷ 144 × 6 × 1.18 = 8.12 bd ft
Door weight182.3535 cu in ÷ 1,728 × 44.029 lb/cu ft = 4.6 lb
Hinges2.11 kg, 635 mm tall, 392 mm wide → 2 per door × 6 = 12
Bore 35 mm Cups for 2 Concealed Hinges per Door
Standard concealed hinges use a 35 mm cup. Place them as far apart as the door allows; the wider the spacing, the more securely the door hangs.

Cabinet Door Calculator Formulas by Mounting Style

Face-frame overlay doors equal the opening plus twice the overlay. Inset doors equal the opening minus twice the gap. Frameless doors equal the outside of the box minus twice the reveal.

Each rule works the same way on width and height, by hand or in cabinet door calculator math. A pair of doors splits the total width after the center gap comes out, so only the width changes when one door becomes two.

D is the door width or height, O is the opening and v is the overlay on each side. For inset doors swap the plus for a minus and use the gap. For frameless doors use the box size and the reveal.

D single is the width one door would have, and c is the gap where the two doors meet. On a 30 × 24 in opening with a 1/2 in overlay and a 1/8 in gap, each door is (31 - 0.125) ÷ 2 = 15 7/16 in wide.

Mounting (30 × 24 in opening)Per SideSingle DoorEach Door of a Pair
Partial overlay1/2 in overlay31 × 25 in15 7/16 × 25 in
Full overlay1 1/4 in overlay32 1/2 × 26 1/2 in16 3/16 × 26 1/2 in
Inset1/16 in gap29 7/8 × 23 7/8 in14 7/8 × 23 7/8 in
Inset1/8 in gap29 3/4 × 23 3/4 in14 13/16 × 23 3/4 in
Frameless (30 × 24 in box)1/16 in reveal29 7/8 × 23 7/8 in14 7/8 × 23 7/8 in
Frameless (30 × 24 in box)1/8 in reveal29 3/4 × 23 3/4 in14 13/16 × 23 3/4 in

The frameless reveal sets the shadow line between neighboring boxes. At 1/16 in per side, two boxes side by side show a 1/8 in line between doors. The common "box minus 1/4 in" rule uses 1/8 in per side and doubles that line to 1/4 in.

Settle the reveal before a cabinet door calculator run on frameless boxes, because the 1/16 in and 1/8 in choices change a single door by 1/8 in each way and each door of a pair by 1/16 in in width.

Match the row to the hinge already on the cabinet. A cabinet door calculator result in the overlay row is wrong for an inset hinge, and the error is more than an inch each way on this opening.

Choosing an Overlay Size for Face-Frame Cabinets

A 1/2 in partial overlay is the usual starting value in a cabinet door calculator estimate, and 1 1/4 in is the common full overlay.

Door maker Cabinet Doors 'N' More lists both as its common sizes and offers overlays from 0 to 3 in, in 1/8 in steps.

The face-frame stile between two openings limits how far doors can overlay. Each door covers part of it, so the frame left showing is the stile width minus both overlays. Below zero, the doors hit no matter what a cabinet door calculator size says.

Shared Stile Width3/8 in Overlay1/2 in Overlay1 1/4 in Overlay
1 1/2 in3/4 in frame shows1/2 in frame showsDoors overlap by 1 in
1 3/4 in1 in frame shows3/4 in frame showsDoors overlap by 3/4 in
2 in1 1/4 in frame shows1 in frame showsDoors overlap by 1/2 in

A full 1 1/4 in overlay on both sides needs a shared stile of at least 2 5/8 in to keep a 1/8 in gap. On standard 1 1/2 in stiles, a full overlay look comes from a smaller overlay on the inside edges and the full amount only on the outside edges.

Full overlay and half overlay differ in how much frame they hide. Full overlay leaves only a gap between doors. Half overlay, also called partial, leaves a strip of frame between every pair of doors, as the 1/2 in column shows.

Uneven overlays need two runs of the math. If the top rail takes a 3/4 in overlay and the sides take 1/2 in, size the width with 1/2 in and the height with 3/4 in, since one overlay figure in cabinet door calculator math covers all four edges.

Measuring Openings for Replacement Doors

Measure the cabinet opening inside the face frame, not the old door, to the nearest 1/16 in (1.6 mm) before any cabinet door calculator work. For frameless cabinets, measure the outside of the box instead, since there is no frame opening to read.

Take the width at the top, middle and bottom of the opening, and the height at both sides. Use the smallest reading for inset doors, because an inset door that is 1/16 in too big will not close in the tight spot.

The overlay of the old doors can be backed out before they come off, which gives cabinet door calculator numbers the right starting value. Subtract the opening from the old door and halve it.

D old is the old door size and O is the opening. A 14 3/4 × 30 in opening with a 16 × 31 1/4 in door gives (16 - 14.75) ÷ 2 = 5/8 in on the sides and the same 5/8 in on the top and bottom.

When the two directions give different overlays, the old doors used uneven overlay. Size width and height separately, or the new doors will sit off from the old hinge plates.

Old hinges set the overlay for any cabinet door measurement calculator estimate. Keeping 1/2 in overlay hinges means every new door must be the opening plus 1 in each way.

Pairs, Center Gaps and Wide Openings

Split an opening into a pair once one door would pass 23 5/8 in (600 mm) wide. Blum's hinge guide caps doors at 600 mm wide and says a door must not be wider than it is tall, which sets the maximum size for a cabinet door on concealed hinges.

With a 1/2 in overlay, a single door passes 600 mm on openings from 22 5/8 in wide. The cabinet door calculator figures below use a 24 in tall opening, red oak shaker doors with a 1/4 in panel and a 1/8 in center gap.

Opening WidthSingle DoorHinges (Single)Each Door of a PairHinges per Door (Pair)
15 in16 × 25 in27 15/16 × 25 in2
18 in19 × 25 in29 7/16 × 25 in2
21 in22 × 25 in210 15/16 × 25 in2
22 3/4 in23 3/4 × 25 in311 13/16 × 25 in2
27 in28 × 25 in (wider than tall)313 15/16 × 25 in2
36 in37 × 25 in (wider than tall)318 7/16 × 25 in2
48 in49 × 25 in (wider than tall)324 7/16 × 25 in3

A door past 23 5/8 in wide sits outside the hinge maker's tested range, so these counts add a third hinge as a margin. That extra hinge does not make a door wider than it is tall acceptable, since Blum rules those out.

A 48 in opening shows the limit of a pair. Each door is 24 7/16 in wide, still past 600 mm, so three doors or a center stile is the better layout for that kitchen cabinet door calculator case.

The center gap only touches the width of a pair in a cabinet door calculator result. A 1/8 in gap takes 1/16 in off each door of a pair, and a zero gap leaves the doors rubbing as soon as the wood swells.

Shaker Rail, Stile and Panel Sizes

Shaker stiles run the full door height on any shaker cabinet door calculator cut list. Rails equal the door width minus two stile widths plus two groove depths, because each rail carries a stub tenon into the stile groove.

R is the rail length, W is the door width, s is the stile and rail width and g is the groove depth. A 15 7/16 in door with 2 1/4 in stiles and a 3/8 in groove gets rails of 15.4375 - 4.5 + 0.75 = 11 11/16 in.

P is the panel width, and e is the expansion gap on each side that lets a solid panel move with humidity. Panel height uses the same formula with the door height.

With 2 1/4 in stiles, a 3/8 in groove and a 1/16 in gap, the shortcuts match a cabinet door calculator cut list built on those three numbers. Rails are W - 3 3/4 in, and the panel is W - 3 7/8 in by H - 3 7/8 in.

Door Size2 Stiles2 RailsPanelFrame Stock per Door
12 × 30 in30 in8 1/4 in8 1/8 × 26 1/8 in6.38 ft
15 × 30 in30 in11 1/4 in11 1/8 × 26 1/8 in6.88 ft
18 × 30 in30 in14 1/4 in14 1/8 × 26 1/8 in7.38 ft
21 × 36 in36 in17 1/4 in17 1/8 × 32 1/8 in8.88 ft
18 × 42 in42 in14 1/4 in14 1/8 × 38 1/8 in9.38 ft

Stile width is a style choice, but it moves every number in a wooden cabinet door calculator estimate. On a 15 7/16 × 25 in door, going from 1 3/4 in to 3 in stiles shortens the rails by 2 1/2 in and adds about a pound.

Stile and Rail WidthRail LengthPanelRed Oak Door Weight
1 3/4 in12 11/16 in12 9/16 × 22 1/8 in4.2 lb
2 in12 3/16 in12 1/16 × 21 5/8 in4.4 lb
2 1/4 in11 11/16 in11 9/16 × 21 1/8 in4.6 lb
2 1/2 in11 3/16 in11 1/16 × 20 5/8 in4.8 lb
3 in10 3/16 in10 1/16 × 19 5/8 in5.2 lb

Tall doors often get a mid rail. An 18 × 60 in door with one panel takes a 14 1/8 × 56 1/8 in panel, while a mid rail splits it into two 14 1/8 × 27 1/4 in panels that are easier to keep flat.

Raised panel doors use the same frame sizes. Only the panel edge changes, since it is shaped down to fit the groove, so a raised panel cabinet door calculator cut list matches a flat shaker one part for part.

Cope-and-stick doors follow the same cabinet door calculator rail formula, with the profile depth of the bit set, often 3/8 in, in place of the groove depth.

The same stile, rail and panel math also lays out a paneled wall section in the Wainscoting Calculator.

Hinge Count by Height and Weight

Doors up to 900 mm (about 35 3/8 in) tall take two hinges, up to 1600 mm (just under 63 in) take three, up to 2000 mm (just under 78 3/4 in) take four and up to 2400 mm (94 1/2 in) take five. A heavy door moves up a step sooner.

Blum's hinge catalog adds a spacing rule: the top and bottom hinges must sit farther apart than the door is wide. The counts below are for 18 in wide red oak doors, 3/4 in thick.

Door HeightShaker WeightShaker HingesSlab WeightSlab Hinges
24 in5.0 lb28.3 lb2
30 in6.1 lb210.3 lb2
36 in7.1 lb312.4 lb3
48 in9.3 lb316.5 lb3
60 in11.4 lb320.6 lb3
72 in13.5 lb424.8 lb4
84 in15.6 lb528.9 lb5
90 in16.6 lb531.0 lb5

Height sets the count on most doors, but weight takes over on wide, solid ones. A 22 × 34 in red oak slab weighs 14.3 lb and needs three hinges, while a shaker door of the same size weighs 7.9 lb and hangs on two.

Short wide doors can fail the spacing rule even with the right cabinet door calculator hinge count. On an 18 × 24 in door, hinges set 3 in from each end are exactly 18 in apart, so move them closer to the ends to clear the door width.

Wardrobe doors sit at the top of the cabinet door calculator hinge table, with five hinges on an 84 in pantry or wardrobe door. Past 2400 mm tall a door is beyond these hinge counts and needs a heavier hinge system or a split into two doors.

Door Weight by Wood Species

A 15 7/16 × 25 in red oak shaker door with a 1/4 in panel weighs about 4.6 lb. Door weight is volume times density in cabinet door calculator math, and density comes from specific gravity at 12% moisture content.

G is the specific gravity at 12% moisture, 62.4 lb/ft³ is the density of water and 1.12 adds the 12% water in the wood. The G values come from Table 5-3a of the USDA Wood Handbook.

SpeciesSpecific GravityDensity15 7/16 × 25 in Shaker18 × 72 in Shaker18 × 30 in Slab
White oak0.6847.5 lb/ft³ (761 kg/m³)5.0 lb14.6 lb11.1 lb
Red oak0.6344.0 lb/ft³ (705 kg/m³)4.6 lb13.5 lb10.3 lb
Hard maple0.6344.0 lb/ft³ (705 kg/m³)4.6 lb13.5 lb10.3 lb
Cherry0.5034.9 lb/ft³ (560 kg/m³)3.7 lb10.7 lb8.2 lb
Poplar0.4229.4 lb/ft³ (470 kg/m³)3.1 lb9.0 lb6.9 lb
Red alder0.4128.7 lb/ft³ (459 kg/m³)3.0 lb8.8 lb6.7 lb

Blum bases its hinge guide on 19 mm chipboard at 750 kg/m³. Only white oak is denser, so a white oak slab near a hinge step is the door most likely to need one more hinge than its height suggests.

These weights assume the panel is the same wood as the frame. An 18 × 72 in shaker door still needs four hinges in every species, because height governs at that size, not the 5.8 lb spread between white oak and alder.

Lumber, Sheets and Cost for a Kitchen

Five 30 × 24 in openings with pairs, or ten shaker doors, need 13.53 board feet of 4/4 red oak with 18% waste and one 4 × 8 sheet for the panels. At $6.50 per board foot and $55 per sheet, that is $142.94, or $14.29 per door.

w is the stile width, L is the part length and t is the rough thickness, all in inches, with 144 cubic inches in one board foot.

Doors 13/16 in thick or less are priced as 4/4 rough stock, and 7/8 or 1 in doors move to 5/4, which raises a 15 7/16 × 25 in door from 1.15 to 1.43 board feet before waste.

Openings (Pairs)DoorsShaker LumberPanel SheetsShaker CostSlab SheetsSlab Cost
122.71 bd ft1$72.591$59.72
368.12 bd ft1$107.761$69.15
51013.53 bd ft1$142.942$133.59
81621.65 bd ft1$195.702$147.74
122432.47 bd ft2$321.043$221.61

Slab totals in the cabinet door calculator table include edge banding at $0.35 per foot, which is 6.74 ft per 15 7/16 × 25 in door. Each extra sheet jumps the total, so five slab pairs cost almost as much as eight.

Area math undercounts sheets in any cabinet door calculator estimate that skips kerf. Ten 15 7/16 × 25 in slabs cover 26.8 sq ft, under one 32 sq ft sheet, but only nine fit with 1/8 in kerfs.

A slab door has to come from one piece of sheet stock, so 48 × 96 in, the size of one 4 × 8 sheet, is the largest slab door.

Tall doors also lose more to layout. Six 18 × 72 in slabs total 54 sq ft, which area math rounds to two sheets, yet only two fit on each 48 in wide sheet, so the job takes three.

Painted doors need finish on both faces and all edges, on top of the cabinet door calculator lumber and sheet cost. One 15 7/16 × 25 in face is 2.68 sq ft, so a pair of doors carries about 10.7 sq ft of surface for the Paint Calculator.

Gap, Overlay and Hinge Answers

Gaps, overlay type and hinge size decide whether a cabinet door calculator result fits the cabinet already on the wall, so each is worth settling before the first cut.

How much gap should you leave around and between cabinet doors?

Leave 1/16 to 1/8 in around inset doors and about 1/8 in between the two doors of a pair. A 3/32 in inset gap splits the difference and gives a 29 13/16 × 23 13/16 in door on a 30 × 24 in opening.

Solid wood doors move with the seasons, so a gap tight enough to look crisp in dry winter air can bind by summer. Overlay doors have no side gap to set, since the overlay covers the frame edge.

What is the difference between inset and overlay cabinet doors?

Inset doors sit inside the face frame, flush with it, and are smaller than the opening. Overlay doors sit on the face of the frame and are larger than the opening, so they hide the gap and the frame edge.

On a 30 × 24 in opening, a 1/2 in overlay door has 775 sq in of face against 713 sq in for a 1/16 in inset door, about 9% more wood. Inset doors also need inset hinges and tighter gaps.

What size concealed hinge do I need?

Most concealed cabinet hinges use a 35 mm (1 3/8 in) cup. Blum's US catalog lists a 13 mm minimum depth for its 35 mm holes, so a 3/4 in (19 mm) door leaves enough wood behind the cup.

The hinge overlay must match the door overlay. A 1/2 in overlay door takes a 1/2 in overlay hinge, a full overlay door takes a full overlay hinge and an inset door takes an inset hinge.