Drywall Calculator

Updated

Drywall calculator for walls and ceilings that counts 4 × 8, 4 × 12 or 54 in sheets after doors, windows and gables, plus joint compound, paper tape, screws, board weight and cost.

Drywall Setup

Measure each wall at the floor and the height to the ceiling.

Doors, Windows & Gables2 Doors · 2 Windows
Board, Framing & Waste1/2 in · 16 in O.C. · 10% Waste
Prices & Labor$215.00 Total
Drywall to Buy
13 Sheets of 4 × 8 ft Drywall
9 for walls and 4 for the ceiling, 10% waste included
356 sq ft of Drywall Surface
Openings Removed64 sq ft
Waste and Offcuts60 sq ft, 14.4%
Surface to cover, less any openings, and the board you pay for that ends up as offcuts after rounding to whole sheets.
3.2 gal Joint Compound
4.5-Gal Pails1 Pail
Joint Tape132 ft, 1 × 250 ft roll
Ready-mixed compound and paper tape at the rates USG gives for finishing gypsum board, about two pails per 1,000 sq ft.
334 Drywall Screws
Screws per Sheet28 wall, 35 ceiling
Board Weight541 to 582 lb
Screws at USG spacing of 16 in on walls and 12 in on ceilings, the corner bead or screws per sheet, and the board weight.
$215.00 Material Cost
Per Sq Ft of Surface$0.60
Boards$195.00
Boards and mud pails at your prices, plus hanging and finishing labor when entered, spread over the surface.
Every Sheet Size for This Job4 × 8 ft row marked
Sheet SizeSheetsBoard BoughtOffcutsScrewsWeight
4 × 8 ft13416 sq ft14.4%334541-582 lb
4 × 9 ft12432 sq ft17.6%298562-605 lb
4 × 10 ft11440 sq ft19.1%305572-616 lb
4 × 12 ft9432 sq ft17.6%319562-605 lb
4 × 14 ft8448 sq ft20.5%301582-627 lb
54 in × 12 ft9486 sq ft26.8%350632-680 lb
1200 × 2600 mm13437 sq ft18.5%319568-611 lb
1200 × 3000 mm11426 sq ft16.5%316554-597 lb
Sheets and Supplies by Surface Area10% waste on sheets
Drywall Surface4 × 8 Sheets4 × 12 SheetsCompoundTape
100 sq ft430.9 gal37 ft
250 sq ft962.25 gal92.5 ft
356 sq ft (yours)1393.2 gal132 ft
500 sq ft18124.5 gal185 ft
1,000 sq ft35239 gal370 ft
1,200 sq ft422810.8 gal444 ft
2,000 sq ft694618 gal740 ft
3,000 sq ft1046927 gal1,110 ft
Step-by-Step Math356 sq ft surface
  1. Walls = 2 × (10 ft + 10 ft) × 8 ft = 320 sq ft - openings 64 sq ft = 256 sq ft.
  2. Ceiling = 10 ft × 10 ft = 100 sq ft.
  3. Wall sheets = 256 sq ft × 1.1 ÷ 32 sq ft per 4 × 8 ft sheet, rounded up = 9.
  4. Ceiling sheets = 100 sq ft × 1.1 ÷ 32 sq ft per 4 × 8 ft sheet, rounded up = 4.
  5. Compound = 356 sq ft × 9 gal per 1,000 sq ft = 3.2 gal, 1 pail; tape at 370 ft per 1,000 sq ft = 132 ft.
  6. Screws = 28 per wall sheet and 35 per ceiling sheet on 16 in framing, over the net area = 334.
  7. Cost = boards $195.00 + mud $20.00 = $215.00.
  8. Result: 13 Sheets of 4 × 8 ft Drywall.
13 Sheets, 416 sq ft of Board
Hang wall board horizontally across the studs and fasten at 16 in on walls and 12 in on ceilings, as USG specifies.

Sheet Count in a Drywall Calculator Estimate

By drywall calculator math, a 10 × 10 ft room with 8 ft walls, two doors and two windows takes 13 sheets of 4 × 8 drywall: 9 for the walls and 4 for the ceiling, with 10% added for cuts and breakage.

L and W are the room length and width, H is the wall height, G is any gable triangle area, O is the door and window area, w is the waste allowance as a decimal and S is the area of one sheet. In any drywall calculator count, walls and ceiling round up separately because ceiling board rarely comes from wall offcuts.

For the 10 × 10 drywall calculator example, those 13 sheets hold 416 sq ft of board for 356 sq ft of surface, so 14.4% of what you pay for ends up as offcut. That share is the real waste, and it is higher than the 10% allowance because every surface rounds up to whole sheets.

A drywall calculator with windows and doors is only as good as its measurements, so measure each wall along the floor and the height to the ceiling, then round up to the next half foot. A wall that measures 8 ft 1 in still needs a strip above two rows of 4 ft board, and that strip comes from a full sheet.

Openings: Subtract Them or Keep the Board

In a drywall calculator for walls, subtracting doors and windows saves 2 sheets in the 10 × 10 room: 13 sheets with the openings taken out against 15 with none removed. The two doors at 3 × 6.67 ft and two windows at 3 × 4 ft cover 64 sq ft of wall.

Some makers tell you not to subtract at all. CertainTeed's drywall estimator asks for area without deducting doors, windows or outlets, which builds the cutouts into the board count as spare stock.

Subtract openings when they are large and grouped, such as a patio door or a run of windows, because those cutouts leave pieces too small to reuse. Keep the board for a single small window, since the sheet over it is usually cut from one piece anyway.

For a room with many openings, the Wall Square Footage Calculator nets each wall separately. That same net area also drives the paint order in the Paint Calculator.

Room Sizes From 10x10 to 20x20

A drywall calculator walls and ceiling total scales with the room's perimeter and ceiling, not its floor area alone. With 8 ft walls, one door and one window, a 12 × 12 ft room takes 18 sheets of 4 × 8 or 13 sheets of 4 × 12.

RoomDrywall Surface4 × 8 Wall + Ceiling4 × 8 Total4 × 12 TotalCompoundScrews
10 × 10 ft388 sq ft10 + 414103.5 gal362
10 × 12 ft440 sq ft11 + 516114.0 gal412
12 × 12 ft496 sq ft13 + 518134.5 gal466
12 × 14 ft552 sq ft14 + 620135.0 gal520
14 × 16 ft672 sq ft16 + 824176.0 gal637
16 × 20 ft864 sq ft19 + 1130217.8 gal826
20 × 20 ft1,008 sq ft21 + 1435249.1 gal970

Every row of this drywall calculator table is based on one 3 × 6.67 ft door, one 3 × 4 ft window and 10% waste. A 4 × 12 sheet covers 1.5 times the area of a 4 × 8, so the larger sheet cuts the count by about a third and leaves fewer butt joints to tape.

The trade-off is handling. A 4 × 12 sheet of 1/2 in lightweight board weighs over 60 lb and needs two people, while a 4 × 8 can go up a stairway and onto a ceiling lift alone.

Tall Walls and 54 in Board

Tall walls change the drywall calculator sheet count: a 9 ft wall wastes board when it is hung in 4 ft rows, since two rows reach only 8 ft and the last foot comes from a third row. Board 54 in wide covers 9 ft in two rows with one horizontal seam, and National Gypsum makes it for that reason.

Sheet SizeSheets for 12 × 12 ft, 9 ft WallsBoard BoughtOffcut ShareScrews
4 × 8 ft19608 sq ft10.5%508
4 × 9 ft18648 sq ft16.1%452
4 × 10 ft15600 sq ft9.3%464
4 × 12 ft14672 sq ft19.1%484
54 in × 12 ft12648 sq ft16.1%531

In this drywall size calculator comparison, the room has 544 sq ft of surface after one door and one window. The 54 in sheet needs the fewest pieces, while 4 × 10 buys the least board, so the choice comes down to seams against cost.

Fewer seams usually win on finish quality. Every horizontal seam is a joint to tape and feather, and the 54 in board removes the strip seam that a 4 ft board leaves near the ceiling of a 9 ft wall.

Joint Compound and Tape per 1,000 Sq Ft

Finishing 1,000 sq ft of drywall takes about two 4.5 gal pails of ready-mixed joint compound, or 9 gal. That is USG's own coverage figure for its Sheetrock UltraLightweight All Purpose compound.

A common drywall calculator shortcut of 0.05 lb of compound per square foot works out to only 50 lb for 1,000 sq ft, well under the weight of the two pails USG quotes. Order from the pail rate and you finish the job; order from the shortcut and you buy again before the second coat.

Drywall Surface4 × 8 Sheets4 × 12 SheetsCompound4.5 gal PailsPaper Tape
100 sq ft430.9 gal137 ft
250 sq ft962.25 gal193 ft
500 sq ft18124.5 gal1185 ft
1,000 sq ft35239 gal2370 ft
1,200 sq ft422810.8 gal3444 ft
2,000 sq ft694618 gal4740 ft
3,000 sq ft1046927 gal61,110 ft

In the drywall calculator square feet table above, sheet counts include 10% waste, while compound and tape are figured on the surface itself. Tape runs about 370 ft per 1,000 sq ft, so a 250 ft roll covers a room up to about 675 sq ft and a 500 ft roll most of a 1,350 sq ft job.

Texture adds compound on top of finishing. A knockdown or orange-peel coat is a separate order sized by the texture maker's coverage, so price it apart from the tape-and-finish mud.

Outside corners need metal or paper-faced corner bead, one stick per corner at full wall height. Bead is commonly stocked in 8 ft and 10 ft sticks, so 3 outside corners on a 9 ft wall take 27 ft, or three 10 ft sticks, since an 8 ft stick would need a joint.

A plain rectangular room has only inside corners, which are taped, not beaded. Bump-outs, soffits, window returns and the end of a half wall are where outside corners add up, so count them before the drywall calculator order goes in.

Screws per Sheet on 16 or 24 in Framing

For a drywall calculator screw count, a 4 × 8 sheet hung on a wall over studs at 16 in takes 28 screws, and the same sheet on a ceiling takes 35. Fasteners go into every framing member the sheet crosses, at 16 in apart on walls and 12 in apart on ceilings.

Sheet SizeWall, 16 in FramingCeiling, 16 in FramingWall, 24 in FramingCeiling, 24 in Framing
4 × 8 ft28352025
4 × 10 ft32402430
4 × 12 ft40502835
54 in × 12 ft50603542

A 4 × 8 sheet laid across studs at 16 in spans seven studs, with four screws down each one. Framing at 24 in drops that to five studs, so the same wall uses about 30% fewer screws.

The 10 × 10 room with two doors and two windows needs 334 screws. Screws are sold by the pound and counts per pound vary with length and thread, so check the box count before you buy by weight.

Houses of 1,000 to 3,000 Sq Ft

A whole-house drywall calculator by square footage starts from one ratio: a house needs about three times its floor area in drywall surface, because every room has four walls and a ceiling. A 1,200 sq ft house comes to roughly 3,770 sq ft of surface, or 130 sheets of 4 × 8 with 10% waste.

Floor AreaRoomsDrywall Surface4 × 8 Sheets4 × 12 SheetsCompound Pails
1,000 sq ft63,170 sq ft109737
1,200 sq ft73,770 sq ft130878
1,500 sq ft84,590 sq ft15810610
2,000 sq ft106,000 sq ft20713813
3,000 sq ft148,830 sq ft30420318

The table models square rooms of equal size with 8 ft walls, two door faces and one window per room. Real plans with hallways, closets and long narrow rooms add wall per square foot, so treat each row as a floor for budgeting, not a final order.

A house order is far more accurate room by room. Summing each room's own drywall calculator count catches the closets, stairwells and vaulted ceilings that a floor-area ratio cannot see.

Half-Inch, Type X and Sheet Weight

Standard walls and ceilings use 1/2 in drywall, and assemblies that need a fire rating use 5/8 in Type X; check your local code for where it applies. Weight rises with thickness, which matters when one person is lifting board overhead.

BoardWeight per Sq Ft4 × 8 Sheet4 × 12 Sheet
1/2 in lightweight1.3 to 1.4 lb42 to 45 lb62 to 67 lb
5/8 in Firecode 30 or LITE 301.6 to 1.8 lb51 to 58 lb77 to 86 lb
5/8 in Type X lightweight1.9 lb61 lb91 lb

Weight belongs in a drywall calculator plan too: the 13 sheets for the 10 × 10 room weigh 541 to 582 lb in 1/2 in lightweight board. Check the floor load and the stair route before a delivery is dropped in one spot upstairs.

A 4 × 8 sheet is sold as 48 × 96 in, and the standard US sizes run 4 × 8, 4 × 9, 4 × 10, 4 × 12 and 4 × 14 ft, plus 54 in wide board. Drywall and Sheetrock are the same material: Sheetrock is USG's brand name for gypsum board.

To check the thickness of board already on a wall, pull a switch-plate cover with the power off and measure the cut edge beside the box. A door jamb that stops short of the wall face also shows the board edge.

Gables, Ceilings and Metric Sheets

A gable wall adds a triangle above the rectangle: half the base times the height. Two gable ends 10 ft wide and 4 ft tall add 40 sq ft, or 1.25 more sheets of 4 × 8 before waste.

Ceiling area in a drywall calculator estimate is length times width, the same math as walls, but ceilings hang on 12 in screw spacing and often in longer sheets to cut butt joints overhead. A 10 × 10 ceiling takes 4 sheets of 4 × 8 or 3 of 4 × 12 with waste.

Metric board follows the same rule for a drywall calculator metric estimate. A 1200 × 2600 mm sheet covers 3.12 m², or 33.6 sq ft, and a 1200 × 3000 mm sheet suits walls a little under 3 m tall.

Ceiling drywall calculator totals are where longer sheets pay off most. Every butt joint on a ceiling is finished overhead, so a sheet that spans the room in one piece saves more labor than the same choice on a wall.

Material and Labor Cost per Sheet

For the drywall calculator cost line, at $15 per 4 × 8 sheet and $20 per pail of compound, board and mud for the 10 × 10 room cost $215, or $0.60 per sq ft of surface. The board alone works out to $0.47 per sq ft of sheet bought.

Labor is usually quoted per square foot of surface hung and finished. At an example rate of $2.00 per sq ft, the same room adds $712 of labor, which is more than three times the material.

For a quick drywall cost estimator check, multiply sheets by sheet price, add pails at your store price, then add labor on the net surface. Tape and screws add only a few dollars a room, so compound and board drive the material line.

The rest of the room has its own orders. Count baseboard with the Baseboard Trim Calculator and seal the corners with the Sealant Calculator once the walls are painted.