Coplanar Waveguide Calculator

Updated

Coplanar waveguide calculator for a line with or without a bottom ground: get impedance from trace, gap and substrate, or solve width or gap for a target, plus wavelength and loss.

Coplanar Waveguide Setup

Enter the trace, gap and substrate to get the coplanar waveguide impedance.

Bottom Ground Plane
Dk
Ω
Metal, Frequency & Loss1 oz · 2.4 GHz · tanδ 0.02
tanδ
49.1 Ω Characteristic Impedance
Exact 49.122 Ω · grounded CPW with 1.38 mil metal
2.81 Effective Permittivity
Phase Velocity59.7% of c
Field in Substrate (q)53.2%
Share of the field in the substrate sets εeff, which fixes speed, wavelength and delay.
2.93 in Wavelength at 2.4 GHz
Quarter Wave (λg/4)0.734 in
Phase Shift per in123°
Guided wavelength on this line, for sizing stubs, quarter-wave sections and phase.
2.89 pF/in Line Capacitance
Line Inductance6.97 nH/in
Propagation Delay142 ps/in
Per-length capacitance and inductance of the line, from its impedance and delay.
0.155 dB/in Dielectric Loss
Zero-Thickness Z050.7 Ω
TE Surface-Wave Cutoff80.0 GHz
Dielectric loss at your frequency, Z0 if the metal were thin, and where modes start.
CPW Cross-Section DiagramW 30.0 · S 10.0 · h 20.0 mil
Bottom ground planeW 30.0 milS 10.0S 10.0GroundGroundh 20.0 mil · εr 4.4Z0 49.1 Ω · εeff 2.81
Impedance vs Trace Width ChartS 10.0 mil, h 20.0 mil
0050.025.010050.015075.0200100Trace width W (mil)Z0 (Ω)30.0 mil, 49.1 Ω
With groundNo ground
Width Table for Common Z0S 10.0 mil, εr 4.4
Target Z0Width, With GroundWidth, No Ground
25.0 Ω93.0 mil (2.36 mm)Not practical
35.0 Ω55.4 mil (1.41 mm)813 mil (20.6 mm)
49.1 Ω30.0 mil (0.762 mm)93.4 mil (2.37 mm)
50.0 Ω28.9 mil (0.735 mm)84.6 mil (2.15 mm)
75.0 Ω11.1 mil (0.282 mm)12.9 mil (0.328 mm)
100 Ω4.57 mil (0.116 mm)3.94 mil (0.100 mm)
Step-by-Step Math10 steps
1. Inputs in milAll lengths already in mil
2. Modulus k1k1 = W ÷ (W + 2S) = 30 ÷ (30 + 2 × 10) = 0.6; K(k1) ÷ K(k1′) = 0.8774
3. Modulus k3k3 = tanh(πW ÷ 4h) ÷ tanh(π(W + 2S) ÷ 4h) = 0.8601; K(k3) ÷ K(k3′) = 1.264
4. Zero-Thickness εeffq = R3 ÷ (R1 + R3) = 0.5903; εeff = 1 + q(εr - 1) = 1 + 0.5903 × (4.4 - 1) = 3.007
5. Zero-Thickness Z0Z0 = 60π ÷ √εeff ÷ (R1 + R3) = 188.4 ÷ √3.007 ÷ (0.8774 + 1.264) = 50.71 Ω
6. Metal ThicknessΔ = (1.25t ÷ π)(1 + ln(4πW ÷ t)) = 3.625 mil; W + Δ, S - Δ and εeff,t = 2.808 give Z0,t = 49.12 Ω
7. Used for ResultsZ0 = 49.12 Ω, εeff = 2.808, q = (εeff - 1) ÷ (εr - 1) = 0.5319
8. Wave and Delayλg = 299.8 ÷ f(GHz) ÷ √εeff = 299.8 ÷ 2.4 ÷ √2.808 = 74.54 mm; tpd = 84.73 × √εeff = 142 ps/in
9. Dielectric Lossαd = π × εr × q × tanδ ÷ (λ0 × √εeff) = 0.7024 Np/m = 0.155 dB/in; fTE = c ÷ (4h√(εr - 1)) = 80.01 GHz
10. Result49.1 Ω Characteristic Impedance
49.1 Ω Coplanar Line on εr 4.4
Quasi-static conformal mapping from Wadell and Simons, the method most CPW calculators use. Stitch the top grounds to the bottom plane with a via fence along both sides.

Conformal Mapping in a Coplanar Waveguide Calculator

A 30 mil trace with 10 mil gaps on a 20 mil, εr 4.4 board measures 50.7 Ω as grounded coplanar waveguide with thin copper and 49.1 Ω with 1 oz copper. Coplanar waveguide calculator math gets there through ratios of elliptic integrals.

W is the center trace width and S the gap to each side ground, so k1 describes the top-side copper alone. With W at 30 mil and S at 10 mil, k1 is 0.6 and K(k1)/K(k1') is 0.877.

h is the substrate thickness down to the bottom ground, and k3 brings that plane into the math. On the same board k3 is 0.860 and its ratio K(k3)/K(k3') is 1.264; with no bottom ground the tanh terms become sinh terms.

K is the complete elliptic integral of the first kind and k' equals √(1 - k²). With 60π taken as η0/2, or 188.4, the default line works out to 188.4 ÷ √3.007 ÷ 2.142 = 50.7 Ω.

These are the quasi-static equations in Rainee Simons's Coplanar Waveguide Circuits, Components, and Systems and Brian Wadell's Transmission Line Design Handbook, the basis of most coplanar waveguide calculator formula pages online.

The bottom plane pulls field into the dielectric. With thin copper, 59.0% of the field sits in the substrate (q), so εeff is 1 + 0.590 × 3.4 = 3.01, against 2.38 without ground, the widest split between the two coplanar waveguide calculator cases.

Trace Widths for 50 Ω on FR-4 and Rogers

In coplanar waveguide calculator terms, a grounded 50 Ω line on a 0.8 mm FR-4 core at εr 4.4 needs a 0.95 mm trace with 0.2 mm gaps when copper thickness is set to 0. Remove the bottom ground and the same 50 Ω needs a 2.26 mm trace.

Substrate and ThicknessGap SWidth With GroundWidth Without Groundεeff With Ground
FR-4, 0.2 mm0.15 mm0.341 mm3.20 mm3.11
FR-4, 0.2 mm0.3 mm0.380 mm9.79 mm3.28
FR-4, 0.8 mm0.15 mm0.822 mm1.50 mm2.83
FR-4, 0.8 mm0.2 mm0.951 mm2.26 mm2.88
FR-4, 0.8 mm0.3 mm1.12 mm4.22 mm2.95
FR-4, 1.6 mm0.15 mm1.05 mm1.30 mm2.75
FR-4, 1.6 mm0.3 mm1.65 mm3.00 mm2.83
RO4350B, 0.254 mm0.15 mm0.493 mm4.07 mm2.54
RO4350B, 0.254 mm0.3 mm0.557 mm11.4 mm2.66
RO4350B, 0.508 mm0.15 mm0.803 mm2.93 mm2.43
RO4350B, 0.508 mm0.2 mm0.885 mm4.47 mm2.47
RO4350B, 0.508 mm0.3 mm0.986 mm8.14 mm2.54

Widths assume zero metal thickness, with RO4350B taken at εr 3.48. Real 1 oz copper narrows every one, most of all where the gap is tight, as the metal thickness section shows.

On a thin 0.2 mm core the gap hardly matters: doubling it from 0.15 to 0.3 mm only widens the grounded trace from 0.341 to 0.380 mm, since most field already runs to the plane below.

Coplanar waveguide without ground suits thick boards only. On 1.6 mm FR-4 it needs 1.30 mm at 0.15 mm gaps, close to the grounded 1.05 mm, but on thin cores the no-ground width balloons past 9 mm.

The Dk value moves a coplanar waveguide calculator answer as much as the geometry does. Rogers lists RO4350B at 3.48 for process control and 3.66 as its design Dk, and solving at 3.66 narrows the 0.508 mm, 0.2 mm-gap trace from 0.885 to 0.849 mm.

Gap and Substrate Decide Whether the Ground Matters

A bottom ground only changes the answer while the substrate is thin next to the gap. For a 30 mil trace with 10 mil gaps on εr 4.4 with thin copper, the two versions differ by 18.9 Ω on 20 mil substrate but by just 1.9 Ω at 80 mil.

Substrate hZ0 With GroundZ0 Without Groundεeff With Groundεeff Without Ground
5 mil (0.127 mm)22.6 Ω83.0 Ω3.711.67
10 mil (0.254 mm)36.3 Ω75.3 Ω3.352.03
20 mil (0.508 mm)50.7 Ω69.6 Ω3.012.38
40 mil (1.02 mm)60.1 Ω66.7 Ω2.812.59
80 mil (2.03 mm)63.8 Ω65.7 Ω2.732.67
160 mil (4.06 mm)64.9 Ω65.4 Ω2.712.69

Both columns head toward 65.3 Ω, the value for an infinitely thick substrate. Past a substrate about 1.6 times the total W + 2S span, any coplanar waveguide calculator result with or without ground lands within 2 Ω.

Gap S (W 30, h 20 mil, t = 0)S ÷ hZ0 With GroundZ0 Without Ground
4 mil0.243.3 Ω53.2 Ω
6 mil0.346.6 Ω59.6 Ω
10 mil0.550.7 Ω69.6 Ω
15 mil0.7553.6 Ω79.5 Ω
20 mil1.055.4 Ω87.9 Ω
30 mil1.557.3 Ω101.9 Ω
60 mil3.059.9 Ω132.7 Ω

Opening the gap past the substrate thickness barely moves a grounded line: 55.4 Ω at S equal to h, 59.9 Ω at three times h. The line has become microstrip with distant side grounds, so keep S at or below h when the gap is meant to set the impedance.

The Microstrip Impedance Calculator covers that wide-gap limit directly. Coupled or differential coplanar pairs need even- and odd-mode equations that a single-line coplanar waveguide calculator does not include.

Effective Permittivity, Wavelength and Delay

The default line with 1 oz copper has an εeff of 2.81, so signals travel at 59.7% of light speed, or 142.0 ps per inch. Without the bottom ground the same geometry drops to εeff 2.24 and 126.9 ps per inch.

λg is the guided wavelength on the line, c is 299.8 mm/ns and f the frequency in GHz. Stubs, quarter-wave transformers and phase lengths all scale from λg, so every coplanar waveguide calculator wavelength is the guided one.

FrequencyGuided WavelengthQuarter Wave (mm)Quarter Wave (in)
915 MHz195.5 mm48.9 mm1.92 in
2.4 GHz74.5 mm18.6 mm0.734 in
5.8 GHz30.8 mm7.71 mm0.304 in
10 GHz17.9 mm4.47 mm0.176 in
24 GHz7.5 mm1.86 mm0.073 in

Per-length capacitance and inductance follow from Z0 and delay alone. C is tpd ÷ Z0, or 2.89 pF/in, and L is Z0 × tpd, or 6.97 nH/in, which answers coplanar waveguide capacitance and inductance questions without separate formulas.

Choosing the wrong ground option before a coplanar waveguide calculator estimate puts every stub off frequency. With εeff 2.24 instead of 2.81, a 2.4 GHz quarter wave comes out 12% too long, pulling a notch down by about 255 MHz.

Loss Tangent and Dielectric Loss per Inch

On the default grounded line over 20 mil FR-4 at tanδ 0.02 with 1 oz copper, dielectric loss is 0.155 dB/in at 2.4 GHz and 0.646 dB/in at 10 GHz. The same geometry on RO4350B at tanδ 0.0037 drops to 0.025 and 0.104 dB/in.

αd is in nepers per metre, multiplied by 8.686 for dB, λ0 is the free-space wavelength and q the filling factor. It is the quasi-TEM dielectric loss from David Pozar's Microwave Engineering, with q equal to (εeff - 1) ÷ (εr - 1).

FrequencyFR-4, εr 4.4, tanδ 0.02RO4350B, εr 3.48, tanδ 0.0037FR-4 Loss Over 4 in
1 GHz0.065 dB/in0.010 dB/in0.26 dB
2.4 GHz0.155 dB/in0.025 dB/in0.62 dB
5.8 GHz0.375 dB/in0.060 dB/in1.50 dB
10 GHz0.646 dB/in0.104 dB/in2.58 dB
28 GHz1.81 dB/in0.291 dB/in7.23 dB

The laminate choice outweighs any coplanar waveguide calculator geometry tweak at millimetre-wave frequencies. At 28 GHz, 4 in of FR-4 grounded CPW loses 7.23 dB to the dielectric alone, against 1.16 dB on RO4350B.

Copper and foil-roughness loss come on top and grow with √f, so total loss on a long line runs higher than these figures. A coplanar waveguide loss calculator estimate that includes only the dielectric is the floor, not the total.

Metal Thickness Shifts the Impedance

Copper thickness lowers impedance by widening the trace edge and narrowing the gap. On the default geometry, 1 oz copper takes the 50.7 Ω thin-copper result down to 49.1 Ω, and 2 oz copper takes it to 46.7 Ω.

t is the metal thickness, W the trace width and Δ the extra effective width that the copper's edges add to the trace.

The trace is then treated as W + Δ wide and the gap as S - Δ, with εeff trimmed as well, following the thickness correction in Gupta, Garg, Bahl and Bhartia's Microstrip Lines and Slotlines.

CopperThickness tW 30, S 10, h 20 mil (50.7 Ω)W 10, S 4, h 10 mil (59.1 Ω)
0.5 oz0.689 mil-0.80 Ω-2.82 Ω
1 oz1.378 mil-1.59 Ω-7.61 Ω
2 oz2.756 mil-4.01 ΩCorrection fails

Narrow gaps feel thickness most in coplanar waveguide calculator math. The 10 mil line with 4 mil gaps loses 7.61 Ω at 1 oz, and at 2 oz the edge growth exceeds the gap, so a field solver has to take over.

Solder mask or coating over the gaps pulls impedance below the bare-copper coplanar waveguide calculator figure. For a trace under a layer, the Embedded Microstrip Impedance Calculator is the closer model.

Surface-Wave Cutoff and Via Fence Pitch

Grounded CPW on 1.6 mm FR-4 begins to support TE surface waves at 25.4 GHz, while 0.508 mm RO4350B holds out to 93.7 GHz. Above that cutoff the quasi-static impedance and loss stop holding.

fTE is the lowest TE surface-wave cutoff on a grounded slab, per Simons, with h the substrate thickness. Thinner and lower-Dk cores push it higher, widening the range where coplanar waveguide calculator results hold.

Substrate ThicknessFR-4 (εr 4.4)RO4350B (εr 3.48)
0.1 mm406.5 GHz475.9 GHz
0.2 mm203.2 GHz238.0 GHz
0.254 mm160.0 GHz187.4 GHz
0.508 mm80.0 GHz93.7 GHz
0.8 mm50.8 GHz59.5 GHz
1.6 mm25.4 GHz29.7 GHz

Stitching vias tie the top grounds to the bottom plane so the two cannot resonate as a parallel-plate guide, an effect outside quasi-static coplanar waveguide calculator math.

The Seeed Studio Wio-LR2021 PCB design guide spaces them at λ/20 or less, while looser guidance stops at λ/10.

Frequencyλg, Default Line on 20 mil FR-4Pitch at λg/10Pitch at λg/20
2.4 GHz74.5 mm7.45 mm3.73 mm
5.8 GHz30.8 mm3.08 mm1.54 mm
10 GHz17.9 mm1.79 mm0.89 mm
28 GHz6.39 mm0.64 mm0.32 mm

At 5.8 GHz the tighter λg/20 rule asks for vias every 1.54 mm, which routes easily. At 28 GHz it falls to 0.32 mm, close to a standard drill diameter, which pushes most designs toward smaller vias or a thinner, lower-Dk core.