Gambrel Roof Calculator

Updated

Gambrel Roof Calculator for barn and shed framing from width, length and two slopes, with rafter lengths, knuckle and cut angles, ridge height, roof area, attic volume and framing.

Quick Setup

Enter both slopes and one known measurement. Measure the eaves overhang level from the wall face.

Walls, Framing and Waste10 ft walls, 24 in o.c., 10% waste

Wall height runs from the floor to the top plate. Spacing sets how many gambrel frames you need.

%
Gambrel Roof Area
1,881.7 sq ft Roof Surface
15 ft 9 1/8 in total roof height · 25 ft 9 1/8 in floor to ridge
13 ft 1/8 in Lower Rafter
Lower Rise (y1)11 ft 9 1/2 in
Total Lower Rafter (R1t)15 ft 4 5/8 in
R1 runs from the wall plate to the knuckle. R1t adds the eave tail, e ÷ cos θ along the slope.
9 ft 4 1/2 in Upper Rafter
Upper Run (x2)8 ft 6 in
Upper Rise (y2)3 ft 11 5/8 in
Upper rafter R2 runs from the knuckle to the ridge. Upper run and rise use half the width.
140.00° Knuckle Angle
Lower Pitch (x:12)25.73/12
Upper Pitch (x:12)5.6/12
Inside angle where the two slopes meet. Gussets and the knuckle cut follow it.
10,767 cu ft Attic Volume
Lower Segment (A1)584.5 sq ft
Upper Segment (A2)356.4 sq ft
Space under the roof above the top plates. Segment areas are one side, with eave tail and gable overhangs.
Rafter Cut ListFrom a square cut; steep cuts to the edge
RafterLengthTop CutBottom CutPer Frame
Upper (R2)9 ft 4 1/2 in25.00° at ridge20.00° at knuckle2
Lower (R1t)15 ft 4 5/8 in20.00° at knuckle25.00° to rafter edge, plumb tail2
Framing and Roofing Order19 frames, 63 bundles, 65 sheets
ItemOrderBased On
Gambrel Frames19 frames36.0 ft ÷ 2.00 ft spacing + 1
Rafter Stock940.8 ft19 frames × 4 rafters
Gusset Plates114 plates3 joints per frame, both faces
Roofing Squares20.70 squares1,881.7 sq ft + 10% waste
Shingle Bundles63 bundles3 bundles per square
4×8 Sheathing65 sheets2,069.9 sq ft ÷ 32 sq ft per sheet
Gambrel End View Diagram65.00° and 25.00°, your numbers
28 ft spanθ 65.00° lower · Φ 25.00° upper11 ft 9 1/2 in y115 ft 9 1/8 in H15 ft 4 5/8 in R1t9 ft 4 1/2 in R2θΦ299.1 sq ftend wall above
Gambrel Dimensions by WidthSame angles at other widths
WidthHeight (H)Lower RunLower RafterUpper Rafter
8.0 ft4 ft 6 in1 ft 6 7/8 in3 ft 8 5/8 in2 ft 8 1/8 in
10.0 ft5 ft 7 1/2 in1 ft 11 5/8 in4 ft 7 3/4 in3 ft 4 1/4 in
12.0 ft6 ft 9 in2 ft 4 1/4 in5 ft 6 7/8 in4 ft 1/4 in
14.0 ft7 ft 10 1/2 in2 ft 9 in6 ft 6 1/8 in4 ft 8 1/4 in
16.0 ft9 ft3 ft 1 3/4 in7 ft 5 1/4 in5 ft 4 1/4 in
20.0 ft11 ft 3 1/8 in3 ft 11 1/8 in9 ft 3 1/2 in6 ft 8 3/8 in
24.0 ft13 ft 6 1/8 in4 ft 8 5/8 in11 ft 1 7/8 in8 ft 1/2 in
28.0 ft (yours)15 ft 9 1/8 in5 ft 6 in13 ft 1/8 in9 ft 4 1/2 in
30.0 ft16 ft 10 5/8 in5 ft 10 3/4 in13 ft 11 3/8 in10 ft 5/8 in
36.0 ft20 ft 3 1/8 in7 ft 7/8 in16 ft 8 3/4 in12 ft 3/4 in
Step-by-Step Math7 steps with your numbers
  1. Half width: 28 ft ÷ 2 = 14 ft
  2. Upper run: x2 = 14 - 5.5 = 8.5 ft
  3. Rises: y1 = 5.5 × tan 65° = 11.7948 ft; y2 = 8.5 × tan 25° = 3.9636 ft; H = 15.7584 ft
  4. Rafters: R1 = √(5.5² + 11.7948²) = 13.0141 ft; R2 = √(8.5² + 3.9636²) = 9.3787 ft
  5. Total lower rafter: R1t = R1 + e ÷ cos θ = 13.0141 + 1 ÷ cos 65° = 15.3803 ft
  6. Segment areas: A1 = (36 + 2 × 1) × 15.3803 = 584.5 sq ft; A2 = 38 × 9.3787 = 356.4 sq ft
  7. Total roof area: At = 2 × (A1 + A2) = 1,881.7 sq ft
Steep Lower Slope Over 21/12
Past 21/12, standard shingle nailing no longer holds. Use the shingle maker’s steep-slope fastening and hand-seal each shingle with asphalt roofing cement.

Gambrel Roof Calculator Math for Height, Rafters and Area

A gambrel roof is solved one half at a time. Each side has a steep lower slope and a shallow upper slope, and their two runs always add up to half the building width.

H is the roof height above the wall plates, W is the building width, x1 is the level run of the lower slope, θ is the lower angle and Φ is the upper angle. The upper run is whatever is left of the half width.

Take a 28 x 36 ft barn with a 65° lower slope, a 25° upper slope and a 5.5 ft lower run. The lower rise is 5.5 x tan 65° = 11.79 ft, and the upper run is 14 - 5.5 = 8.5 ft with a rise of 3.96 ft.

That puts the ridge 15 ft 9 1/8 in above the plates, or 25 ft 9 1/8 in above the floor on 10 ft walls. The lower rafter is 13 ft 1/8 in and the upper rafter is 9 ft 4 1/2 in, each from the Pythagorean rule.

A is the roof surface, L is the building length, g is the gable overhang at each end, e is the level eave overhang, and R1 and R2 are the lower and upper rafters. With 1 ft overhangs the barn carries 1,881.7 sq ft of roof.

One known measurement besides the two angles is enough for any gambrel roof calculator estimate. A lower rise, an upper rafter or the total height all fix where the knuckle sits, because the half width is already known.

Shed Gambrel Dimensions at 8 to 16 ft Wide

A 10 ft wide gambrel shed built to 67.5° and 22.5° stands 5 ft tall above the walls and uses four rafters of 3 ft 9 7/8 in each. These angles split a half circle into four equal chords, a common gambrel roof calculator starting point.

The table is a gambrel roof dimensions chart in feet and inches for that layout. It covers the gambrel roof angles 10 ft wide and 12 ft wide sheds most often use, plus 8, 14 and 16 ft spans.

Shed WidthRoof HeightLower RunLower RiseEach RafterLoft Width at Knuckle
8 ft4 ft1 ft 2 in2 ft 10 in3 ft 3/4 in5 ft 7 7/8 in
10 ft5 ft1 ft 5 5/8 in3 ft 6 3/8 in3 ft 9 7/8 in7 ft 7/8 in
12 ft6 ft1 ft 9 1/8 in4 ft 2 7/8 in4 ft 7 1/8 in8 ft 5 7/8 in
14 ft7 ft2 ft 5/8 in4 ft 11 3/8 in5 ft 4 1/4 in9 ft 10 3/4 in
16 ft8 ft2 ft 4 1/8 in5 ft 7 7/8 in6 ft 1 1/2 in11 ft 3 3/4 in

Rafter lengths are wall plate to knuckle and knuckle to ridge, with no eave tail. Add the tail from the eave section below, and take half the ridge board thickness off each upper rafter if you frame with one.

A 12 ft shed at these angles has only 6 ft from plate to ridge. For standing headroom in the loft, a gambrel roof calculator for shed builds usually needs taller walls rather than steeper slopes.

Knuckle and Rafter Cut Angles

Each rafter end at the knuckle is cut at half the difference between the two slopes. For 65° and 25° that is 20°, and the frame closes at a 140° inside angle.

Lower / Upper AnglePitchesInside Knuckle AngleKnuckle Cut, Each RafterRidge CutLevel Seat Cut
60° / 15°20.78/12 and 3.22/12135°22.5°15°30°
65° / 20°25.73/12 and 4.37/12135°22.5°20°25°
67.5° / 22.5°28.97/12 and 4.97/12135°22.5°22.5°22.5°
70° / 25°32.97/12 and 5.6/12135°22.5°25°20°
65° / 25°25.73/12 and 5.6/12140°20°25°25°
60° / 30°20.78/12 and 6.93/12150°15°30°30°

Gambrel roof calculator angles for cuts are miter-saw settings from a square cut, and cuts past 45° read from the rafter edge.

Any half-circle layout puts the upper slope 45° below the lower one, so its knuckle cut is always 22.5° and its knuckle angle always 135°.

The 67.5° and 22.5° pair is the only one where every cut matches. One pattern rafter can then lay out all four pieces of a gambrel truss design, which saves time on a run of identical frames.

Plan six gusset plates per frame in any gambrel roof calculator order, one on each face of the two knuckles and the ridge. The Roof Truss Calculator handles spacing for common trusses on the same building.

Eave Tails Add More Than the Overhang

A 1 ft level eave overhang on a 65° lower slope needs 2 ft 4 3/8 in of extra rafter, and the eave tip ends 2 ft 1 3/4 in below the wall plate. Steep slopes stretch every inch of overhang.

In gambrel roof calculator math, the rafter tail is the level overhang divided by the cosine of the lower angle. Adding the 1 ft straight onto the 28 x 36 barn's rafters would leave the roof 103.8 sq ft short, about one full square of shingles.

Lower Angle0.5 ft Overhang: Tail / Drop1 ft Overhang: Tail / Drop1.5 ft Overhang: Tail / Drop
60°1 ft / 10 3/8 in2 ft / 1 ft 8 3/4 in3 ft / 2 ft 7 1/8 in
65°1 ft 2 1/4 in / 1 ft 7/8 in2 ft 4 3/8 in / 2 ft 1 3/4 in3 ft 6 5/8 in / 3 ft 2 5/8 in
67.5°1 ft 3 5/8 in / 1 ft 2 1/2 in2 ft 7 3/8 in / 2 ft 5 in3 ft 11 in / 3 ft 7 1/2 in
70°1 ft 5 1/2 in / 1 ft 4 1/2 in2 ft 11 1/8 in / 2 ft 9 in4 ft 4 5/8 in / 4 ft 1 1/2 in

The drop matters on a low wall. A 1.5 ft overhang at 70° brings the eave 4 ft 1 1/2 in down a 7 ft shed wall, which can block a door or window head near the corner.

A plumb tail cut on a 65° rafter is 65° from square, past most miter saws, so lay it out as 25° to the rafter edge and cut it with a circular saw. The Birdsmouth Cut Calculator sizes the seat notch where the tail rafter crosses the wall.

Steep Lower Slopes and the 21/12 Shingle Limit

Most gambrel lower slopes are steeper than 21/12, which is 60.26°. The Asphalt Roofing Manufacturers Association treats 21/12 as the top of normal shingle application in its steep slope and mansard guidance.

Above that slope, shingles follow the maker's steep-slope fastening and get hand-sealed. ARMA calls for four quarter-size spots of ASTM D4586 asphalt cement under each laminated shingle, or two under each tab of a three-tab shingle.

Lower AnglePitchOver 21/12?
60°20.78/12No
62°22.57/12Yes
65°25.73/12Yes
67.5°28.97/12Yes
70°32.97/12Yes

The upper slope has the opposite problem. IRC R905.2.2, summarized in the LSU AgCenter roofing guide, bars shingles below 2/12 (9.46°) and requires two layers of underlayment up to 4/12 (18.43°).

In a half-circle gambrel roof calculator layout, a 60° lower slope puts the upper slope at 15°, or 3.22/12, so its top section needs double underlayment. A 65° lower slope lifts it to 20°, clearing 4/12 and the extra layer.

Shingle orders from a gambrel roof calculator for shingles need both checks on one roof. Metal panels are another option for the steep lower section, and the Metal Roof Cost Calculator prices that option.

Square Footage and Framing Order for a 28 x 36 Barn

A gambrel roof calculator estimate for the 28 x 36 ft barn at 65° and 25° comes to 20.70 squares with 10% waste. That comes to 63 bundles of shingles at 3 per square and 65 sheets of 4 x 8 sheathing.

Framing at 24 in on center takes 19 gambrel frames, which is 36 ÷ 2 + 1. That is 76 rafters with 940.8 ft of rafter stock, including eave tails, and 114 gusset plates.

For other barn sizes, the gambrel roof calculator square feet figures below use half-circle layouts, 1 ft eave and gable overhangs, and 10% waste. Frames are at 24 in on center.

BuildingRoof Height65° / 20° Roof AreaBundles67.5° / 22.5° Roof AreaBundlesFrames
12 x 16 ft6 ft415.5 sq ft14424.7 sq ft159
16 x 20 ft8 ft642.4 sq ft22653.8 sq ft2211
24 x 32 ft12 ft1,408.8 sq ft471,426.8 sq ft4817
28 x 36 ft14 ft1,807.0 sq ft601,827.3 sq ft6119
30 x 40 ft15 ft2,125.6 sq ft712,148.2 sq ft7121
32 x 48 ft16 ft2,683.5 sq ft892,710.5 sq ft9025

Steepening a half-circle layout from 65° to 67.5° adds only about 1% to the roof. The two-pitch 65° and 25° barn carries 1,881.7 sq ft against 1,807.0 sq ft for the half-circle version, since its ridge sits 1.76 ft higher.

Gambrel roof calculator cost questions start from these quantities, since prices change by region and roofing type. The Roof Shingle Calculator turns any of these areas into a shingle order.

Loft Space Compared With a Gable

Gambrel roof calculator math puts 10,767 cu ft above the plates of the 28 x 36 ft barn, 35.6% more than a gable of the same 15 ft 9 1/8 in height. That extra space is the gambrel's main advantage over a gable.

Usable floor width shows the gain better than volume. At 7 ft above the plates, the gambrel is 21.5 ft wide inside its rafters, while the same-height gable is only 15.6 ft wide.

The trade is roofing. The same-height gable on this footprint needs 1,716.4 sq ft of roof, so the gambrel adds 165.2 sq ft, or 9.6%. The Gable Roof Area Calculator runs the gable side of that comparison.

The knuckle sets the loft. In the 65° and 25° barn the knuckles sit 11 ft 9 1/2 in above the plates and 17 ft apart, which frames a tall, straight-walled loft under the shallow upper slope.

Pitches, Rafter Lengths and Angles

Feet-and-inch and metric layouts follow the same tangent and Pythagorean steps, so gambrel roof calculator math in inches or meters produces the same shape at any width.

How many pitches does a gambrel roof have?

A gambrel roof has two pitches, repeated on each side, which makes four roof planes. A 65° lower and 25° upper layout works out to 25.73/12 below the knuckle and 5.6/12 above it.

Equal pitches turn any gambrel roof calculator layout into a plain gable. If the upper slope is the steeper one, the pitches were swapped, since a gambrel always has its steep slope below the knuckle.

How do you determine rafter length for a gambrel roof?

Determine each gambrel rafter length as the square root of its run squared plus its rise squared. Add the eave tail to the lower rafter, which is the level overhang divided by the cosine of the lower angle.

In a gambrel roof calculator run in meters, a 6 m wide garage framed to 67.5° and 22.5° has two rafters of 2.296 m per side and a roof height of 3.0 m. A 0.3 m eave stretches the lower rafter to 3.08 m.

On an 8 m long building with 0.3 m gable overhangs, that roof is 92.47 m² and holds 101.82 m³ above the walls. Frames at 600 mm centers come to 14. The Rafter Length Calculator covers single-pitch rafters.

What are the angles of a gambrel roof?

Gambrel roofs usually run a lower slope of 60° to 70° and an upper slope of 15° to 30°. The half-circle layout sets the upper slope exactly 45° below the lower one, such as 65° with 20°.

Two-pitch layouts can pair any angles in gambrel roof calculator math, as long as the lower slope is steeper. Use the Roof Pitch Calculator to turn a measured rise and run into an angle before laying out either slope.