Roof Truss Calculator

Updated

Roof Truss Calculator for count, spacing, top chord length, overall height with heel, roof angle and package cost of common or mono trusses with gable ends and a truss order sheet.

Quick Setup

Span is the outside-to-outside wall width. Pitch is the rise for every 12 of run.

ft
ft
in
trusses
Truss Type, Overhang and HeelFink, 12 in overhang, 4 in heel
in
in
in
Roof Truss Prices$3,710 package
$ each
$ each
$ total
Order Quantity
21 Roof Trusses
19 common + 2 gable end trusses, every bay equal
14 ft 6 7/16 in Top Chord per Side
Without Overhang13 ft 5 in
Length per Foot of Run13.42 in
Sloped length along the top edge, from the peak or high end out to the tail, with the overhang included.
26.57° Roof Angle
Angle at the Peak126.87°
Slope50%
Angle from level at the heel, plus the angle inside the peak or high-end joint, for cuts and gusset layout.
6 ft 4 in Overall Truss Height
Rise, Wall Line to Peak6 ft
Tail Drop Below Wall Line6 in
Heel height plus rise, from the bottom of the bottom chord to the peak. Check headroom and clearances.
$3,710 Truss Package
Trusses Only$3,210
Per Sq Ft of Floor$3.86 / sq ft
Common and gable end truss prices plus delivery and installation. A truss plant quote sets the final price.
Live Truss DiagramYour numbers to scale
Truss Count by Spacing12 to 48 in on center
Truss Member LengthsFink pattern

Lengths run line to line, before lumber depth and joint cuts. Webs count common trusses only; gable ends get studs.

Truss Order SheetFor the truss supplier
Step-by-Step Roof Truss MathWith your numbers
    Ready for a Truss Quote
    Truss plants engineer each design for your local snow, wind and ceiling loads. Send them the order sheet above.

    Roof Truss Calculator Counts by Building Length

    In roof truss calculator math, a 40 ft building with trusses at 24 in on center takes 21 trusses. That is 20 bays of 24 in, plus the starter truss at the first end wall.

    Here N is the number of trusses, L is the building length along the ridge in feet, and S is the on-center spacing in inches. Round the division up before adding the one.

    The same roof truss calculation formula drops straight into a spreadsheet as =ROUNDUP(L*12/S,0)+1. That covers anyone hunting for a free truss calculator in Excel.

    Building Length16 in O.C.19.2 in O.C.24 in O.C.
    20 ft1614 (last bay 9 5/8 in)11
    24 ft1916 (last bay 19 3/16 in)13
    30 ft24 (last bay 8 in)20 (last bay 14 3/8 in)16
    32 ft2521 (last bay 19 3/16 in)17
    36 ft2824 (last bay 9 5/8 in)19
    40 ft3126 (last bay 19 3/16 in)21
    48 ft3731 (last bay 19 3/16 in)25
    50 ft39 (last bay 8 in)33 (last bay 4 13/16 in)26
    60 ft4639 (last bay 9 5/8 in)31

    Gable end trusses sit inside any roof truss calculator count, not on top of it. On the 40 ft building, the 21 positions are 19 common trusses plus 2 gable end trusses. Adding the gable ends as extras over-orders two trusses.

    A building length that does not divide evenly leaves a short last bay in the roof truss calculator layout. A 41 ft building at 24 in needs 22 trusses with a 12 in last bay. Spread evenly, the same 22 trusses land at 23 7/16 in on center.

    Either layout works, because truss drawings list spacing as a maximum, such as the 24 in maximum on MiTek's standard gable truss details. Even spacing just keeps sheathing joints tidy.

    Overall Height With the Heel Included

    A 24 ft span at 6/12 rises 6 ft from the wall line to the peak. With a 4 in heel, the truss stands 6 ft 4 in from the bottom of the bottom chord. That roof truss calculator height, not the rise, decides delivery and gable wall framing.

    H is the overall truss height, hheel is the heel height at the outside wall line, W is the span, and P is the pitch in inches of rise per 12. For a mono truss, use the full span instead of W/2.

    Span4/126/128/1212/12
    20 ft3 ft 8 in5 ft 4 in7 ft10 ft 4 in
    24 ft4 ft 4 in6 ft 4 in8 ft 4 in12 ft 4 in
    28 ft5 ft7 ft 4 in9 ft 8 in14 ft 4 in
    30 ft5 ft 4 in7 ft 10 in10 ft 4 in15 ft 4 in
    32 ft5 ft 8 in8 ft 4 in11 ft16 ft 4 in
    36 ft6 ft 4 in9 ft 4 in12 ft 4 in18 ft 4 in
    40 ft7 ft10 ft 4 in13 ft 8 in20 ft 4 in

    Each roof truss calculator height above uses a 4 in heel. Many roof truss calculator height formulas measure only half-span times pitch and skip the heel, so they read 4 in short on a standard truss and 12 in short on an energy heel truss.

    Switching the 24 ft, 6/12 truss to a 12 in raised heel lifts it from 6 ft 4 in to 7 ft. Check that against any height limit, and against the gable siding and soffit you planned.

    A standard heel is the vertical depth of the top chord plus the butt cut, which SBCA puts at 1/4 in at most truss plants. The top chord gets deeper vertically as the pitch steepens.

    TC is the actual width of the top chord lumber, 3.5 in for a 2x4 or 5.5 in for a 2x6. P is the pitch per 12 and B is the butt cut. Results below use a 1/4 in butt cut.

    Pitch2x4 Top Chord Heel2x6 Top Chord Heel
    3/123 7/8 in5 15/16 in
    4/123 15/16 in6 1/16 in
    5/124 1/16 in6 3/16 in
    6/124 3/16 in6 3/8 in
    8/124 7/16 in6 7/8 in
    10/124 13/16 in7 7/16 in
    12/125 3/16 in8 in

    Use the heel from this table for a quick roof truss calculator estimate before the plant drawing arrives. Anything taller is a raised heel, usually chosen to fit full-depth attic insulation over the top plate.

    For the ridge height from span and pitch alone, without heel or chord details, the Roof Height Calculator gives the quick figure.

    Pitch, Angle and Low-Slope Limits

    A 6/12 pitch is a 26.57° roof angle and leaves 126.87° inside the peak of a common truss. Those two roof truss calculator angles set the heel cut, the peak cut and the gusset layout.

    PitchRoof AnglePeak Angle, CommonHigh-End Angle, MonoSlopeTop Chord per Foot of Run
    1/124.76°170.47°85.24°8.33%12.04 in
    2/129.46°161.08°80.54°16.67%12.17 in
    3/1214.04°151.93°75.96°25%12.37 in
    4/1218.43°143.13°71.57°33.33%12.65 in
    5/1222.62°134.76°67.38°41.67%13.00 in
    6/1226.57°126.87°63.43°50%13.42 in
    7/1230.26°119.49°59.74°58.33%13.89 in
    8/1233.69°112.62°56.31°66.67%14.42 in
    9/1236.87°106.26°53.13°75%15.00 in
    10/1239.81°100.39°50.19°83.33%15.62 in
    12/1245°90°45°100%16.97 in

    A roof truss angle calculator answer comes from two short rules. The peak of a common truss is 180° minus twice the roof angle, and the high end of a mono truss is 90° minus the roof angle.

    Here θ is the roof angle in degrees and P is the rise per 12 of run. Going the other way, a 22.5° roof equals 12 times tan(22.5°), or about 4.97/12.

    Pitch from a roof truss calculator also limits the roofing. Under IRC Section R905.2.2, asphalt shingles need at least 2/12, and roofs from 2/12 up to 4/12 need two layers of underlayment.

    So a 3/12 truss order should come with a double-underlayment line in the roofing budget. Below 2/12, price a membrane or a metal panel rated for that slope in the Metal Roof Cost Calculator.

    If you only have a rise and a run from an old roof, the Roof Pitch Calculator converts them to the pitch these tables use.

    Mono Truss Numbers for Shed Roofs

    A mono truss uses the whole span as its run, so it rises twice as high as a common truss at the same pitch. A 12 ft span at 4/12 rises 2 ft as a common truss but 4 ft as a mono truss.

    The roof truss calculator top chord grows the same way. With a 12 in overhang, that 12 ft common truss has a 7 ft 4 9/16 in top chord per side, while the mono version runs one 13 ft 8 7/16 in chord.

    Mono truss calculator results for common shed and lean-to spans are below. Each cell gives overall height with a 4 in heel, then the top chord with a 12 in low-side overhang.

    Span1/122/123/124/12
    8 ft1 ft / 9 ft 3/8 in1 ft 8 in / 9 ft 1 1/2 in2 ft 4 in / 9 ft 3 5/16 in3 ft / 9 ft 5 13/16 in
    10 ft1 ft 2 in / 11 ft 7/16 in2 ft / 11 ft 1 13/16 in2 ft 10 in / 11 ft 4 1/16 in3 ft 8 in / 11 ft 7 1/8 in
    12 ft1 ft 4 in / 13 ft 9/16 in2 ft 4 in / 13 ft 2 1/8 in3 ft 4 in / 13 ft 4 13/16 in4 ft 4 in / 13 ft 8 7/16 in
    14 ft1 ft 6 in / 15 ft 5/8 in2 ft 8 in / 15 ft 2 1/2 in3 ft 10 in / 15 ft 5 9/16 in5 ft / 15 ft 9 3/4 in
    16 ft1 ft 8 in / 17 ft 11/16 in3 ft / 17 ft 2 13/16 in4 ft 4 in / 17 ft 6 1/4 in5 ft 8 in / 17 ft 11 1/16 in

    The 1/12 column covers most flat roof truss searches. It keeps a shed nearly level, but it falls below the 2/12 shingle minimum, so it pairs with a membrane or low-slope metal panel.

    Inside a 12 ft, 4/12 mono truss, the verticals at the third points run 1 ft 8 in and 3 ft, the diagonals run 5 ft and 5 ft 10 3/4 in, and the high-end vertical is 4 ft 4 in.

    These roof truss calculator top chord lengths include the low-side overhang only. Add any overhang past the high wall separately, using the top chord length per foot of run from the angle table above.

    Fink and King Post Web Lengths

    On a 24 ft, 6/12 Fink truss with a 4 in heel, the two short webs run 3 ft 10 5/8 in and the two long webs run 7 ft 5 7/8 in. Those are line-to-line lengths along member centerlines.

    Fink webs rise from the third points of the bottom chord. The short web meets the top chord at the quarter point of the span, and the long web meets it at the peak.

    W is the span, hheel is the heel height, P is the pitch per 12 and H is the overall truss height. A king post equals H, and each king post diagonal runs from the foot of the post to the quarter point of a top chord.

    Member, 24 ft SpanPer Truss4/126/128/12
    Top Chord with 12 in Overhang213 ft 8 7/16 in14 ft 6 7/16 in15 ft 7 1/2 in
    Bottom Chord124 ft24 ft24 ft
    Fink Short Web23 ft 7/8 in3 ft 10 5/8 in4 ft 9 1/4 in
    Fink Long Web25 ft 10 3/4 in7 ft 5 7/8 in9 ft 2 15/16 in
    King Post14 ft 4 in6 ft 4 in8 ft 4 in
    King Post Diagonal26 ft 5 1/4 in6 ft 10 3/8 in7 ft 4 13/16 in
    Heel Vertical24 in4 in4 in

    Cut lengths come out shorter than these roof truss calculator figures once lumber depth and joint cuts are taken off. Lay the first truss out full size on the deck and use it as the pattern for the rest.

    The bottom chord is where the two patterns differ most. A Fink truss supports a 24 ft bottom chord at its third points, leaving 8 ft panels, while a king post supports it only at midspan, leaving two 12 ft panels.

    Roof truss calculator web totals barely change between them. At 6/12, the four Fink webs total 22 ft 9 in and the three king post webs total 20 ft 3/4 in, so the Fink pattern costs about 2 ft of extra web per truss.

    Count webs only on common trusses when you build a cut list. On a 40 ft building with 19 common and 2 gable end trusses, that is 38 short and 38 long Fink webs, since gable end trusses use vertical studs instead.

    Site-built trusses still need a design your building department accepts. Lengths from roof truss calculator geometry stop short of the plate sizes, lumber grade and nailing that make the joints carry load.

    Spacing Choices and Roof Trusses Prices

    On a 24 x 40 ft building, moving from 24 in to 16 in spacing adds 10 trusses. At $150 per common truss, that is $1,500 more before any change in delivery or labor.

    C is the package cost, Nc and Ng are the common and gable end truss counts, Pc and Pg are their unit prices, and D is delivery plus installation as one total.

    The table runs that roof truss cost calculator math on a 24 ft span, 40 ft long, with example prices of $150 per common truss, $180 per gable end truss and $500 for delivery and setting.

    SpacingTrussesCommon + Gable EndPackage CostPer Sq Ft of Floor
    12 in4139 + 2$6,710$6.99
    16 in3129 + 2$5,210$5.43
    19.2 in2624 + 2$4,460$4.65
    24 in2119 + 2$3,710$3.86
    48 in119 + 2$2,210$2.30

    Prices per truss vary by region, lumber market and design, so swap in your own quote figures for any roof truss calculator estimate. Gable end trusses cost more because they carry studs for the end wall sheathing.

    The cheapest roof truss calculator count is not always the cheapest roof. Wider spacing makes each truss carry more load, so the plant may upsize chords and raise the unit price, and the sheathing must be rated for the wider span.

    The 19.2 in spacing seen in roof truss calculator charts exists for 8 ft sheets. Five bays of 19.2 in equal 96 in, so every sheet edge lands on a truss, the same way 16 in and 24 in divide evenly into 48 in.

    Metric Truss Layouts in Millimeters

    In a metric roof truss calculator run, a 12 m building at 600 mm centers takes 21 trusses. At 900 mm it takes 15, with a 300 mm last bay, because 12,000 mm does not divide evenly by 900.

    Builders searching for a roof truss calculator in Australia, New Zealand, the UK or South Africa order trusses in millimeters. The count formula is the same with length in millimeters divided by spacing in millimeters.

    Building Length450 mm600 mm900 mm1200 mm
    9 m2116119 (last bay 600 mm)
    12 m28 (last bay 300 mm)2115 (last bay 300 mm)11
    15 m35 (last bay 150 mm)2618 (last bay 600 mm)14 (last bay 600 mm)

    For a metric roof truss calculator check, take an 8 m span at 22.5° with a 450 mm overhang and a 100 mm heel. The top chord runs 4,817 mm per side and the rise is 1,657 mm.

    That truss stands 1,757 mm overall with a 135° angle inside the peak. As a Fink, its short webs run 1,143 mm and its long webs 2,206 mm, line to line.

    Over a 12 m building with 450 mm rakes at both gable ends, the roof deck covers 124.3 m². That is 44 sheets of 1200 x 2400 mm before waste, three more than the 41 sheets without rakes.

    Load Capacity Belongs to the Truss Plant

    Load capacity cannot come from roof truss calculator geometry alone. Under IRC Section R802.10, metal-plate-connected wood trusses are designed to ANSI/TPI 1, and the plant's design drawing sets lumber grade, plates and bracing.

    Truss drawings state loads in pounds per square foot as top chord live, top chord dead, bottom chord live and bottom chord dead. MiTek's standard details list a 40-10-0-10 maximum in that order.

    Spacing in a roof truss calculator layout scales those loads. At 24 in, each truss carries a 2 ft strip, or 100 lb per foot of span from 40 + 10 psf on the top chord. At 16 in, the strip is 1.33 ft and the load drops to 66.7 lb per foot.

    So a roof truss calculator with load capacity is really a design request. Send the plant your ground snow load from the Snow Load Calculator and your roofing dead load from the Roof Weight Calculator.

    Roof truss calculator count and length math holds for steel roof trusses too, since a 40 ft building at 24 in still needs 21 positions. A floor truss calculator is different, because floor trusses have parallel flat chords and no pitch.

    Truss Order, Length and Spacing Answers

    The three questions below cover what truss suppliers ask for on every quote. The worked numbers use a 24 ft span, 6/12 pitch, 12 in overhang, 4 in heel and a 40 ft long building.

    How do I calculate a roof truss order?

    Count the trusses first, then list the roof truss calculator geometry. A 40 ft building at 24 in on center needs 21 trusses, split as 19 common trusses and 2 gable end trusses for a gable roof with both ends closed.

    For each truss type, the supplier needs the span, pitch, web pattern, level overhang, heel height and spacing. The example order reads 24 ft span, 6/12, Fink, 12 in overhang, 4 in heel, 24 in on center.

    Add the roof truss calculator results of 6 ft 4 in overall height and a 14 ft 6 7/16 in top chord per side, so the plant can confirm your numbers against its drawing.

    With 12 in eaves and 12 in rakes at both gable ends, the roof deck covers about 1,221 sq ft, or 39 sheets of 4 x 8 sheathing before waste. Leaving the rakes out would under-order by two sheets.

    For roofing quantities beyond the sheathing, the Gable Roof Area Calculator works out the deck area from span, pitch and length.

    How do you calculate truss length?

    A truss has two lengths. The bottom chord equals the span, and the top chord equals run plus overhang, multiplied by the slope factor for the pitch.

    T is the top chord length, R is the run (half the span on a common truss, the full span on a mono), O is the level overhang and P is the pitch per 12. All lengths share one unit.

    For the 24 ft, 6/12 roof truss calculator example, the run is 12 ft and the slope factor is 1.1180. The top chord is 13 ft 5 in to the wall line and 14 ft 6 7/16 in with the 12 in overhang, or 13.42 in per foot of run.

    The same Pythagorean math sizes stick-framed rafters, so the Rafter Length Calculator gives the same top chord figure for a site-built roof.

    How do you calculate truss spacing?

    Divide the building length in inches by the roof truss calculator count minus one. That gives the even on-center spacing that puts a truss at each end wall.

    S is the spacing in inches, L is the building length in feet and N is the number of trusses. A 40 ft building with 22 trusses spaces them 22 7/8 in on center, and with 25 trusses, exactly 20 in.

    Most residential roofs use 24 in, with 16 in or 19.2 in where heavy roofing, high snow or thin sheathing calls for it. Whatever spacing you use, it must not exceed the maximum on the truss design drawing.