Roof Weight Calculator for the total weight of a roof in lb or kg from roofing material, pitch, layers, deck, rafters, insulation and ceiling, with dead load and snow or live load.
Pick a roofing material from the list beside its weight, or type the weight from the product sheet.
Overhang, Layers, Sheet or Slab
Deck, Framing, Insulation and Ceiling
Solar, Snow and Live Load
Live Roof Assembly Diagram
Roofing Material Weight Chart
Step-by-Step Roof Weight Math
Shingle, Tile and Slate Roof Weight Calculator Chart
Asphalt shingles weigh 2 psf (9.76 kg/m²), fiberglass shingles 3 psf, concrete tile 12 psf and Spanish clay tile 19 psf. Every roof weight calculator figure below is a dry unit weight from Boise Cascade Tech Note GE-1.
The last two columns put each covering on one real house in roof weight calculator math: a 40 x 30 ft footprint, 18 in overhang, 6/12 pitch, 1,586 sq ft of sloped roof, with deck, rafters, insulation and drywall included.
| Roofing | psf | kg/m² | lb per Square | Roofing Only | Whole Roof |
|---|---|---|---|---|---|
| PVC Membrane, 0.05 in | 0.35 | 1.71 | 35 | 555 lb | 10,127 lb |
| Single-Ply Membrane | 0.7 | 3.42 | 70 | 1,111 lb | 10,682 lb |
| Steel Sheet, 0.47 mm | 0.97 | 4.76 | 97 | 1,546 lb | 11,118 lb |
| Three-Ply Ready Roofing | 1 | 4.88 | 100 | 1,586 lb | 11,158 lb |
| Asphalt Shingles | 2 | 9.76 | 200 | 3,173 lb | 12,744 lb |
| Fiberglass Shingles | 3 | 14.65 | 300 | 4,759 lb | 14,331 lb |
| Wood Shingles | 3 | 14.65 | 300 | 4,759 lb | 14,331 lb |
| Four-Ply Felt and Gravel | 5.5 | 26.85 | 550 | 8,726 lb | 18,297 lb |
| Lightweight Clay Tile | 6 | 29.29 | 600 | 9,519 lb | 19,090 lb |
| Five-Ply Felt and Gravel | 6 | 29.29 | 600 | 9,519 lb | 19,090 lb |
| Slate, 3/16 in | 7 | 34.18 | 700 | 11,105 lb | 20,677 lb |
| Slate, 1/4 in | 10 | 48.82 | 1,000 | 15,865 lb | 25,436 lb |
| Single-Ply, Ballasted | 11 | 53.71 | 1,100 | 17,451 lb | 27,023 lb |
| Concrete Roof Tile | 12 | 58.59 | 1,200 | 19,038 lb | 28,609 lb |
| Spanish Clay Tile | 19 | 92.77 | 1,900 | 30,143 lb | 39,715 lb |
The whole-roof column is the roof weight calculator number that matters for framing. On this house, the parts under the roofing weigh 9,571 lb no matter which covering goes on top, so shingles are only a third of the total.
Switching from fiberglass shingles to concrete tile adds 14,279 lb, or 4 times the covering weight. That jump is why a roof weight calculator estimate for shingles cannot be reused when the plan changes to tile.
Shingle figures vary by product line, so a shingle wrapper or data sheet with a weight per square beats any chart. Divide the pounds per square by 100 to get psf, then the Roof Shingle Calculator converts the same area into bundles.
Dead Load on the Slope vs the Horizontal Plan
The 40 x 30 ft house above carries 9.03 psf of dead load on its sloped surface but 10.10 psf on the horizontal plan. Rafter and truss tables use the plan value, so quoting the sloped one understates the load by 1.07 psf, or 10.6%.
Dh is the dead load per square foot of horizontal plan, Wdead is the total roof weight in pounds, and Aplan is the footprint plus overhang seen from above. Snow and live loads act on the same plan area.
Pitch widens that gap in any roof weight calculator result. The table keeps the same house, materials and assembly, and changes only the pitch, so every difference comes from the extra sloped area.
| Pitch | Slope Factor | Sloped Area | Total Dead Weight | psf on Slope | psf on Plan | Design Load on Plan |
|---|---|---|---|---|---|---|
| Flat | 1.0000 | 1,419 sq ft | 13,175 lb | 9.28 | 9.28 | 29.28 psf |
| 3/12 | 1.0308 | 1,463 sq ft | 13,476 lb | 9.21 | 9.50 | 29.50 psf |
| 4/12 | 1.0541 | 1,496 sq ft | 13,705 lb | 9.16 | 9.66 | 29.66 psf |
| 6/12 | 1.1180 | 1,586 sq ft | 14,331 lb | 9.03 | 10.10 | 30.10 psf |
| 8/12 | 1.2019 | 1,705 sq ft | 15,151 lb | 8.88 | 10.68 | 30.68 psf |
| 12/12 | 1.4142 | 2,007 sq ft | 17,231 lb | 8.59 | 12.14 | 32.14 psf |
The psf on the slope drops as the pitch rises, while the plan value climbs. That happens because insulation and drywall sit on the flat ceiling, which never gets bigger, while the roofing, deck and rafters follow the slope.
Design load on plan in this roof weight calculator example is the plan dead load plus a 20 psf roof live load. Spread over 16 in rafter spacing, the 6/12 roof puts 40.1 lb on every foot of rafter, and the 12/12 roof puts 42.9 lb.
Sheet Metal Weight per Square Meter
In roof weight calculator math, a 0.47 mm steel roof sheet weighs 3.69 kg/m² as flat steel and 4.76 kg/m² as laid, once 29% extra metal for ribs and laps is counted. That is 0.97 psf, the lightest covering after membranes.
Here w is the sheet weight in kg/m² of covered roof, t is the total coated thickness in millimeters, ρ is the metal density (7,850 kg/m³ for steel, 2,700 for aluminum), and r is the percent of extra metal in ribs and side laps.
| Sheet | Flat Sheet, kg/m² | With 29% Ribs and Laps, kg/m² | With 29% Ribs and Laps, psf | Per Running Meter, 686 mm Cover |
|---|---|---|---|---|
| Steel, 0.35 mm | 2.75 | 3.54 | 0.73 | 2.43 kg |
| Steel, 0.40 mm | 3.14 | 4.05 | 0.83 | 2.78 kg |
| Steel, 0.47 mm | 3.69 | 4.76 | 0.97 | 3.26 kg |
| Steel, 0.50 mm | 3.93 | 5.06 | 1.04 | 3.47 kg |
| Steel, 0.63 mm | 4.95 | 6.38 | 1.31 | 4.38 kg |
| Aluminum, 0.50 mm | 1.35 | 1.74 | 0.36 | 1.19 kg |
| Aluminum, 0.70 mm | 1.89 | 2.44 | 0.50 | 1.67 kg |
| Aluminum, 0.90 mm | 2.43 | 3.14 | 0.64 | 2.15 kg |
The rib allowance is the number most GI roof sheet weight calculator charts skip. A corrugated or trapezoidal profile uses a wider coil than the width it covers, so the flat-sheet figure underweighs the laid roof by the same percentage.
Check your profile's coil width against its cover width to set that percentage. A 1,220 mm coil rolled to cover 1,000 mm carries 22% extra metal, and a coil that covers 860 mm of a 1,110 mm width carries 29%.
Roof sheeting weight per meter of sheet length is the kg/m² times the cover width from the maker's chart. A 0.47 mm steel sheet with a 686 mm (27 in) cover weighs 3.26 kg per running meter, or 2.19 lb per foot.
wrm is the weight per running meter of sheet, w is the laid weight in kg/m² from the formula above, and b is the cover width in meters. The same sheet with a 1,000 mm cover weighs 4.76 kg per running meter.
Galvanized sheet sold by base-steel thickness weighs more than steel density alone predicts. IS 875 Part 1, Table 1 lists flat 0.63 mm GI sheet at 5.32 to 5.70 kg/m², against 4.95 kg/m² for bare steel.
That 0.37 to 0.75 kg/m² gap is the zinc coating, which varies by coating class. Use the total coated thickness from the data sheet, not the base-steel gauge, and a GI roof sheet weight calculator figure lands on the code value.
For a steel roof weight calculator estimate on a whole house, the 0.47 mm sheet puts 1,546 lb of steel on the 1,586 sq ft example roof. The Metal Roof Cost Calculator turns that same roof into panel counts and price.
Layers Left Under a Recover
A second layer of asphalt shingles adds 3,173 lb to the example house, and fiberglass shingles add 4,759 lb. Each recover stacks the full weight of the old roof under the new one, and a roof weight calculator total has to count it.
| Covering | Layers | Roofing Weight | Whole Roof | Dead Load on Plan | Design Load on Plan |
|---|---|---|---|---|---|
| Asphalt, 2 psf | 1 | 3,173 lb | 12,744 lb | 8.98 psf | 28.98 psf |
| Asphalt, 2 psf | 2 | 6,346 lb | 15,917 lb | 11.22 psf | 31.22 psf |
| Asphalt, 2 psf | 3 | 9,519 lb | 19,090 lb | 13.45 psf | 33.45 psf |
| Fiberglass, 3 psf | 1 | 4,759 lb | 14,331 lb | 10.10 psf | 30.10 psf |
| Fiberglass, 3 psf | 2 | 9,519 lb | 19,090 lb | 13.45 psf | 33.45 psf |
| Fiberglass, 3 psf | 3 | 14,278 lb | 23,850 lb | 16.81 psf | 36.81 psf |
The third-layer rows in this roof weight calculator table are for weighing a tear-off, not planning a recover. IRC Section R908.3.1.1 bars a new roof over two or more existing layers, so a two-layer roof must be stripped to the deck.
That tear-off weight matters for the dumpster too. Two layers of fiberglass shingles on this house come to 9,519 lb, close to 4.8 US tons of debris before any damaged decking is counted.
Deck, Framing and Insulation Weights
On the example house, 1/2 in plywood or OSB weighs 2,697 lb and 2x8 rafters at 16 in weigh 3,490 lb. Together they outweigh the shingles by 1,428 lb, which is why a covering-only roof weight calculator estimate runs light.
| Layer | psf | Area It Covers | Weight on Example House |
|---|---|---|---|
| 3/8 in Plywood or OSB | 1.2 | 1,586 sq ft slope | 1,904 lb |
| 1/2 in Plywood or OSB | 1.7 | 1,586 sq ft slope | 2,697 lb |
| 3/4 in Plywood or OSB | 2.5 | 1,586 sq ft slope | 3,966 lb |
| 1-1/2 in Wood Decking | 4.6 | 1,586 sq ft slope | 7,298 lb |
| 2x6 Rafters at 16 in | 1.7 | 1,586 sq ft slope | 2,697 lb |
| 2x8 Rafters at 16 in | 2.2 | 1,586 sq ft slope | 3,490 lb |
| 2x12 Rafters at 16 in | 3.5 | 1,586 sq ft slope | 5,553 lb |
| Blown Wool, R-38 | 0.62 | 1,200 sq ft ceiling | 744 lb |
| Loose Cellulose, 10 in | 1.4 | 1,200 sq ft ceiling | 1,680 lb |
| Wood Fiberboard, 2 in | 3 | 1,200 sq ft ceiling | 3,600 lb |
| Polyiso Foam Board, 2 in | 0.33 | 1,200 sq ft ceiling | 396 lb |
| 1/2 in Gypsum Board | 2.2 | 1,200 sq ft ceiling | 2,640 lb |
| 5/8 in Gypsum Board | 2.75 | 1,200 sq ft ceiling | 3,300 lb |
Roof weight calculator sheathing weights here are the top of Boise Cascade's plywood and OSB ranges, so a lighter panel may come in 0.2 to 0.3 psf under. The rafter figures assume 16 in spacing; at 24 in, each one drops to two-thirds.
Rigid insulation is where generic charts go wrong. The 1.5 psf per inch often listed for rigid board fits wood fiberboard, while Mule-Hide's Poly ISO 2 data sheet lists polyiso foam at 2 lb per cubic foot.
That density works out to 0.17 psf per inch. Over the 1,200 sq ft ceiling, 2 in of polyiso weighs 396 lb against 3,600 lb for 2 in of wood fiberboard, so the wrong board choice swings a roof weight calculator total by 3,204 lb.
Flat Roof Weight Calculator Totals by Covering
A 40 x 30 ft flat roof with a single-ply membrane weighs 8,904 lb with a plywood deck, 2x8 joists, R-38 and drywall. Ballasting the same membrane with stone raises it to 21,264 lb, a gain of 12,360 lb.
| Flat Roof Covering | psf | Covering Weight | Whole Roof | Dead Load | With 20 psf Live Load |
|---|---|---|---|---|---|
| PVC Membrane, 0.05 in | 0.35 | 420 lb | 8,484 lb | 7.07 psf | 27.07 psf |
| Single-Ply Membrane | 0.7 | 840 lb | 8,904 lb | 7.42 psf | 27.42 psf |
| Three-Ply Ready Roofing | 1 | 1,200 lb | 9,264 lb | 7.72 psf | 27.72 psf |
| Four-Ply Felt and Gravel | 5.5 | 6,600 lb | 14,664 lb | 12.22 psf | 32.22 psf |
| Five-Ply Felt and Gravel | 6 | 7,200 lb | 15,264 lb | 12.72 psf | 32.72 psf |
| Single-Ply, Ballasted | 11 | 13,200 lb | 21,264 lb | 17.72 psf | 37.72 psf |
A flat roof has no slope factor, so sloped area, plan area and footprint are all 1,200 sq ft in this case. Every flat roof weight calculator result is just psf times footprint, which makes the material choice the whole story.
Built-up roofs carry most of their weight in the gravel. Boise Cascade lists dry gravel alone at 8.7 psf, which is why a felt-and-gravel roof weighs 5.5 to 6 psf while three-ply ready roofing without gravel weighs 1 psf.
Concrete Slab Roof Weight in kN/m²
In roof weight calculator terms, a 125 mm reinforced concrete roof slab weighs 3.125 kN/m², or 318.7 kg/m², at 25 kN/m³. On a flat 15 x 10 m roof that is 47,799 kg of concrete before waterproofing, screed or finishes.
ws is the slab self-weight in kN/m², t is the slab thickness in meters and γ is the unit weight of reinforced concrete in kN/m³. Divide kN/m² by 0.00981 for kg/m².
| Slab Thickness | kN/m² | kg/m² | psf | 150 m² Slab |
|---|---|---|---|---|
| 100 mm | 2.500 | 254.9 | 52.21 | 38,239 kg |
| 115 mm | 2.875 | 293.2 | 60.05 | 43,975 kg |
| 125 mm | 3.125 | 318.7 | 65.27 | 47,799 kg |
| 150 mm | 3.750 | 382.4 | 78.32 | 57,359 kg |
| 175 mm | 4.375 | 446.1 | 91.37 | 66,919 kg |
| 200 mm | 5.000 | 509.9 | 104.43 | 76,479 kg |
The 25 kN/m³ roof weight calculator figure sits at the heavy end of the code range. IS 875 Part 1, Table 1 puts reinforced concrete at 22.75 to 24.20 kN/m³ with 1% steel and 24.80 to 26.50 kN/m³ with 5% steel, so 25 is a safe round number.
A slab roof is its own deck and structure, so no plywood or rafter weight goes on top of it. Even so, the 125 mm slab weighs 7.2 times the 9.03 psf shingle roof from the chart, per square meter of roof.
Add a 20 psf (0.98 kN/m²) roof live load and the 125 mm slab carries 4.08 kN/m² on plan. That figure goes to the beams and columns, which an engineer sizes for the slab span, not to any roof weight calculator rule of thumb.
Snow, Solar and Live Load on Top
In a roof weight calculator run with 30 psf of roof snow, the example 6/12 house carries 40.10 psf on plan and 56,901 lb in total. Below 20 psf of snow, the 20 psf roof live load governs, so 0 and 20 psf of snow give the same 30.10 psf design load.
P is the design load on plan, Dh is the plan dead load, Lr is the roof live load and S is the roof snow load. ASCE 7 load combinations take roof live load or snow in the same combination, never the two added together.
| Roof Snow Load | Design Load on Plan | Total Design Weight | Load per Foot of Rafter at 16 in | Dead Load Share |
|---|---|---|---|---|
| 0 psf | 30.10 psf | 42,711 lb | 40.1 lb/ft | 33.6% |
| 20 psf | 30.10 psf | 42,711 lb | 40.1 lb/ft | 33.6% |
| 30 psf | 40.10 psf | 56,901 lb | 53.5 lb/ft | 25.2% |
| 50 psf | 60.10 psf | 85,281 lb | 80.1 lb/ft | 16.8% |
| 70 psf | 80.10 psf | 113,661 lb | 106.8 lb/ft | 12.6% |
The 20 psf live load is the IRC Table R301.6 minimum for roofs up to 4/12 with small tributary areas. Get your roof snow load from the Snow Load Calculator, not from the ground snow map value.
Rafter spacing scales the roof weight calculator line load directly. The same 30 psf snow roof framed at 24 in instead of 16 in puts 80.2 lb on every foot of each rafter, half again as much as the 53.5 lb at 16 in.
In a roof weight calculator estimate, solar panels count as dead load spread over the array area. If panels and racking add 3 psf across the example roof, the dead weight rises by 4,759 lb and the design load on plan reaches 33.45 psf.
A roof load bearing calculator check stops at these loads. Whether 2x8 rafters at 16 in can carry 53.5 lb per foot depends on span, species and grade. For trusses, send these loads to the plant along with the layout from the Roof Truss Calculator.
Calculating Roof Weight, Step by Step
The four questions below come up most when people size a roof. The worked numbers reuse the materials above, with metric figures for the roof sizes asked about outside the US.
What is a roof weight calculator?
A roof weight calculator is an estimate of the total dead weight of a roof, built from area and unit weight per layer. On a 40 x 30 ft house with fiberglass shingles, the answer is 14,331 lb, or 7.17 US tons.
The useful version adds every layer, not just the covering. On that house the shingles are 4,759 lb, deck and rafters 6,187 lb, and insulation with drywall 3,384 lb, so a shingle-only estimate misses two-thirds of the weight.
How do you calculate roof weight & dead load?
For a roof weight calculator total, multiply each layer's psf by the area it covers, then add the layers. Roofing, deck and rafters cover the sloped area, while insulation and ceiling cover the ceiling area under the walls.
W is the total weight, wr the roofing psf, n the number of roofing layers, wd the deck, wf the framing, wi the insulation and wc the ceiling. As is the sloped area and Ac the ceiling area.
For the example house, that is (3 + 1.7 + 2.2) psf x 1,586 sq ft plus (0.62 + 2.2) psf x 1,200 sq ft, or 14,331 lb. Dead load is then 14,331 lb divided by the 1,419 sq ft plan area, or 10.10 psf.
How do you calculate a sloping roof?
In roof weight calculator math, multiply the plan area, overhangs included, by the slope factor for the pitch. The slope factor is the square root of 1 plus the pitch squared, with the pitch written as rise over run.
As is the sloped roof area, Aplan is the footprint plus overhang and P is the rise per 12 of run. A 40 x 30 ft house with 18 in overhangs has a 43 x 33 ft plan, or 1,419 sq ft.
At 6/12, the slope factor is 1.1180, so that roof covers 1,586 sq ft. The same formula works for a hip roof when every plane shares one pitch, and the Roof Pitch Calculator finds the pitch from a measured rise and run.
How much does a 15 m 10 m roof weigh?
A flat 15 x 10 m roof covers 150 m², so its covering weighs 714 kg in 0.47 mm steel sheet, 2,197 kg in fiberglass shingles and 8,788 kg in concrete tile. With a deck, rafters, insulation and drywall, the shingle roof reaches 7,119 kg.
Pitched at 6/12 with no overhang, the same footprint grows to 167.7 m² of roof. The covering then weighs 798 kg in steel sheet, 2,456 kg in fiberglass shingles, 9,826 kg in concrete tile and 15,557 kg in Spanish clay tile.
In the full roof weight calculator total, the pitched roof with fiberglass shingles comes to 7,715 kg, or 46.0 kg/m² of sloped surface. Swap the shingles for the 0.47 mm steel sheet and the whole roof drops to 6,057 kg.
Built as a flat 125 mm reinforced concrete slab, the same 15 x 10 m roof weighs 47,799 kg, close to 48 tonnes. That is 6.7 times the full shingle roof, before any waterproofing or screed.