Gutter Size Calculator

Gutter size calculator for K-style and half-round gutters from roof area, pitch and 5-minute rainfall, with gutter slope, downspout count and size, peak runoff and installed costs.

Roof Area, Pitch & Rainfall

Use the level roof depth from the eave to the ridge or the far edge that drains into this one gutter.

ft
ft
/ 12
in/hr
sq ft
Gutter Slope & Downspouts2×3 in, every 40.0 ft
ft
Gutter & Downspout Price$8.00/ft, $60.00 each
$/ft
$/each
Sized for 4 in/hr Rainfall
5 in K-Style Gutter
Uses 23.9% of its capacity at a 1/16 in/ft slope
660 sq ft Design Roof Area
Level Roof Area600 sq ft
Pitch Factor at 6:121.10
Steeper roofs catch more wind-driven rain, so the level area is raised by a pitch factor before sizing the gutter.
27.5 gpm Peak Runoff
Flow per Downspout13.7 gpm
Water per Inch of Rain411 gal
Peak flow off the roof at your rainfall rate, from design area times rainfall times 0.0104, the figure the gutter must carry.
2 Downspouts, 2×3 in
Spacing Between Downspouts20.0 ft
If Using 3×4 in1 downspout
Enough outlets for the roof area and flow each downspout can take, spaced so no run of gutter is longer than your limit.
$440.00 Gutter Cost
Gutter Run Cost$320.00
Downspout Cost$120.00
Gutter length times your installed price per foot, plus each downspout at your price, for comparing quotes and sizes.
Gutter and Downspout Diagram2 outlets along the run
40.0 ft gutter run, 27.5 gpm at the peak2 downspouts, 20.0 ft of gutter eachGutter slopes down toward each downspout from the high points between them
Gutter Size ChartEvery size at your rainfall
GutterMax Area per Downspout at 4 in/hrCapacity UsedPeak Flow It Carries
5 in K-Style1,380 sq ft24%57.4 gpm
6 in K-Style1,990 sq ft17%82.8 gpm
4 in Half-Round360 sq ft92%15.0 gpm
5 in Half-Round625 sq ft53%26.0 gpm
6 in Half-Round960 sq ft34%39.9 gpm
7 in Half-Round1,380 sq ft24%57.4 gpm
8 in Half-Round1,990 sq ft17%82.8 gpm
Step-by-Step Gutter Sizing Math7 steps
Level roof area40.00 ft × 15.00 ft = 600 sq ft
Design area600 sq ft × 1.10 pitch factor = 660 sq ft
Peak flow660 sq ft × 4 in/hr × 0.0104 = 27.5 gpm
Downspoutslargest of ⌈660 sq ft ÷ 600 sq ft⌉ = 2, ⌈27.5 gpm ÷ 74.0 gpm⌉ = 1 and ⌈40.0 ft ÷ 40.0 ft⌉ = 1, so 2
Load per section660 sq ft ÷ 2 × 4 in/hr = 1,320 sq ft at 1 in/hr
Gutter sizesmallest K-Style that carries it: 5 in, rated 5,520 sq ft at 1 in/hr at this slope
Cost40.0 ft × $8.00/ft + 2 × $60.00 = $440.00
5 in K-Style Handles This Roof
Use your local 5-minute rainfall rate from NOAA Atlas 14, not the hourly figure. Keep the gutter level-to-sloped at least 1/16 in per ft toward each downspout.

Where Rainfall Sets the Gutter Size Calculator Answer

A 5 in K-style gutter drains about 1,380 sq ft of roof at 4 in/hr of rain, not the 5,520 sq ft often quoted. That bigger figure is its capacity at 1 in/hr, so it only holds where storms are mild.

Gutter charts in the International Plumbing Code list roof area at a rainfall of 1 in/hr, the base of any gutter size calculator.

Dividing by the local design rainfall gives the area a gutter really drains, which is the step most gutter size charts leave out.

Rainfall Intensity5 in K-Style6 in K-Style5 in Half-Round6 in Half-Round
2 in/hr (51 mm/hr)2,760 sq ft3,980 sq ft1,250 sq ft1,920 sq ft
3 in/hr (76 mm/hr)1,840 sq ft2,653 sq ft833 sq ft1,280 sq ft
4 in/hr (102 mm/hr)1,380 sq ft1,990 sq ft625 sq ft960 sq ft
5 in/hr (127 mm/hr)1,104 sq ft1,592 sq ft500 sq ft768 sq ft
6 in/hr (152 mm/hr)920 sq ft1,327 sq ft417 sq ft640 sq ft
8 in/hr (203 mm/hr)690 sq ft995 sq ft312 sq ft480 sq ft

Maximum design roof area draining to one outlet, gutter level-pitched at 1/16 in per ft. Half-round values are IPC Table 1106.6 at 1 in/hr divided by the rainfall; K-style uses the 5,520 and 7,960 sq ft figures that This Old House lists.

Every gutter size calculator value in one column carries the same flow. A full 5 in K-style moves about 57 gpm at its limit, whatever the rainfall, so a storm twice as hard halves the roof area it can serve.

How to calculate gutter size?

Multiply the roof's level area by its pitch factor, then by the 5-minute rainfall in in/hr, and split that load over the downspouts. Choose the smallest gutter whose rated area at 1 in/hr covers one section's share.

A 40 ft eave draining a roof 15 ft deep is 600 sq ft of plan in a gutter size calculator example. At 6:12 the pitch factor of 1.1 makes it 660 sq ft, and at 4 in/hr the load is 2,640 sq ft at 1 in/hr.

Two 2 × 3 in downspouts split it to 1,320 each, so a 5 in K-style rated 5,520 runs at 24%, or 48% with one outlet.

Q is peak runoff in gallons per minute, A the design roof area in sq ft and i the rainfall in in/hr. One inch of rain on 1 sq ft is 0.623 gallons, and spread over 60 minutes that is 0.0104 gpm, so the 660 sq ft roof sheds 27.5 gpm.

The same steps sit behind any gutter calculation formula or spreadsheet. A gutter size calculator in square feet that skips the rainfall step gives the 1 in/hr answer, which oversizes the roof area by four times at 4 in/hr.

What rainfall intensity should I use?

Use the 5-minute rainfall for your location at a 10-year or 100-year return period, in in/hr. NOAA's Precipitation Frequency Data Server gives it for any US address from the Atlas 14 data.

Hourly totals are far too low for a gutter size calculator input. Gutters overflow in the first few minutes of a downpour, and a 5-minute peak can run two to three times the 1-hour average rate for the same storm.

Pitch Factors Add Up to 30% of Roof Area

In gutter size calculator math, a 12:12 roof sizes its gutter for 30% more area than its level footprint, while a roof under 4:12 adds nothing. The extra allows for rain driven sideways onto steep slopes, not for the longer sloped surface.

Roof PitchPitch FactorSloped Area MultiplierDesign Area for 600 sq ft Plan5 in K-Style Load at 4 in/hr, One Outlet
Flat to 3:121.00up to 1.031600 sq ft43.5%
4:12 to 5:121.051.054 to 1.083630 sq ft45.7%
6:12 to 8:121.101.118 to 1.202660 sq ft47.8%
9:12 to 11:121.201.250 to 1.357720 sq ft52.2%
12:12 and up1.301.414 and up780 sq ft56.5%

Pitch factors from the roofing trade tables reported by This Old House. Using the sloped roof area instead, as some guides suggest, overstates the design area by about 9% at both 8:12 and 12:12.

Why does roof pitch matter in gutter sizing?

Rain rarely falls straight down in a storm, which a roof gutter size calculator has to allow for, as a steep roof face catches wind-driven rain that a flat one would not. The factor raises the design area by up to 30% to cover that extra water.

Measure the roof area for gutter sizing in plan, as length along the eave times the level depth from eave to ridge. A 40 ft eave on a roof that runs 15 ft back to the ridge is 600 sq ft, whatever its pitch.

Roof pitch can be read off a rafter or worked out with the Roof Pitch Calculator. On a hip roof, each of the four eaves drains its own face, so a roof gutter size calculator count runs once per face.

Slope in the Gutter Buys Capacity

Hanging a 5 in K-style at 1/8 in per ft instead of 1/16 in lets it drain 1,950 sq ft at 4 in/hr instead of 1,380, a 41% gain. At 1/4 in per ft it reaches 2,760 sq ft, double the level-pitched value.

Gutter SlopeDrop Over 40 ft5 in K-Style at 4 in/hr6 in K-Style at 4 in/hr
1/16 in per ft2 1/2 in1,380 sq ft1,990 sq ft
1/8 in per ft5 in1,950 sq ft2,800 sq ft
1/4 in per ft10 in2,760 sq ft3,980 sq ft
1/2 in per ft20 in3,900 sq ft5,600 sq ft

Gutter size calculator capacity scales with slope in IPC Table 1106.6. The catch is the drop, since a 40 ft run at 1/4 in per ft falls 10 in from end to end, which shows on the fascia and can pull the low end away from the roof edge.

How much should gutters slope?

Most residential gutters slope 1/16 to 1/8 in per ft toward the downspout. This Old House cites about 1/4 in per 10 ft as standard, a gentler pitch that looks level from the ground but still drains.

A 1/8 in per ft slope is a good compromise for a gutter size calculator check that falls just short at 1/16 in. On a 40 ft run with a center outlet, each 20 ft half drops only 2 1/2 in at that slope.

Downspouts Decide What Each Gutter Carries

For a downspout calculator count, each 2 × 3 in downspout drains about 600 sq ft of design roof area, and each 3 × 4 in drains about 1,200 sq ft. That rule, 1 sq in of outlet per 100 sq ft of roof, comes from the same trade sources.

Design Roof Area2 × 3 in (600 sq ft)3 × 4 in (1,200 sq ft)3 in Round (706 sq ft)4 in Round (1,255 sq ft)
600 sq ft1111
1,000 sq ft2121
1,500 sq ft3232
2,000 sq ft4232
2,500 sq ft5342

The area rule behind a gutter size calculator downspout count is conservative. IPC Table 1106.2 rates a 3 in round leader for 8,800 sq ft at 1 in/hr, or 2,200 sq ft at 4 in/hr, because the gutter outlet, not the pipe, limits how much water gets in.

Flow still caps each pipe. IPC Table 1106.2 works out to about 92 gpm for a 3 in round leader and 192 gpm for a 4 in, so the flow check only overtakes the area rule above roughly 12.5 and 14.7 in/hr of rain.

How many downspouts do I need for my house?

Use the largest of three counts: design roof area divided by the downspout's rated area, peak flow divided by its flow rating, and gutter length divided by the longest run you allow, often 40 ft. A 40 ft eave draining 660 sq ft needs 2 of 2 × 3 in.

Area sets that count, not flow or length, since one 2 × 3 in outlet covers only 600 sq ft. Switching to a 3 × 4 in downspout drops it to 1, because 660 sq ft fits inside its 1,200 sq ft rating and the 40 ft run is within the length limit.

Why does adding downspouts change the gutter recommendation?

Each gutter section only carries the water between its high point and its own outlet, so the gutter size calculator load belongs to one section at a time.

A center downspout splits a run into two halves, so each half carries half the roof and the gutter can often drop a size.

On a 52 ft eave draining 1,201 sq ft at 7 in/hr, one end outlet needs more than a 6 in K-style can carry level-pitched.

Two halves of 4,204 sq ft at 1 in/hr each fit a 5 in K-style at 76%, and the three 2 × 3 in downspouts its area calls for bring each third down to 51%.

Sizing a 2,000 Sq Ft House

A 2,000 sq ft single-story house needs only 5 in K-style gutters up to 8 in/hr once each long eave has the downspouts its area calls for. With one outlet per eave, it needs 6 in K-style from about 5 in/hr up.

The gutter size calculator house below is 40 × 50 ft with 12 in overhangs, a 6:12 gable and the ridge along the 52 ft length.

RainfallLoad per 52 ft EaveOne Outlet per EaveThree 2 × 3 in DownspoutsTwo 3 × 4 in DownspoutsPeak Runoff per Eave
3 in/hr3,604 sq ft5 in K, 65%5 in K, 22%5 in K, 33%37.5 gpm
4 in/hr4,805 sq ft5 in K, 87%5 in K, 29%5 in K, 44%50.0 gpm
5 in/hr6,006 sq ft6 in K, 75%5 in K, 36%5 in K, 54%62.5 gpm
6 in/hr7,207 sq ft6 in K, 91%5 in K, 44%5 in K, 65%75.0 gpm
8 in/hr9,610 sq ftOver 6 in K5 in K, 58%5 in K, 87%99.9 gpm

In this gutter size chart, each eave drains 52 × 21 ft of plan, or 1,092 sq ft, raised to 1,201 sq ft by the 6:12 pitch factor.

Load is design area times rainfall, shared equally between the outlets and compared against each gutter's rating at 1 in/hr, level-pitched at 1/16 in per ft.

A two-story 2,000 sq ft house has half the roof. A 25 × 40 ft footprint with the same overhangs drains 624 sq ft per eave, and a 5 in K-style handles it at 90% at 8 in/hr even with a single outlet.

What size gutters do I need for a 2,000 sq. ft. house?

For the one-story house above, 5 in K-style gutters work at any rainfall up to 8 in/hr with three 2 × 3 in downspouts per 52 ft eave. With a single corner downspout per eave, 5 in works only up to 4 in/hr.

The floor area matters less to a gutter size calculator than how the roof drains, since one eave carries whatever roof slopes down to it.

A two-story house of the same floor area has half the roof per eave and stays at 5 in in almost any US climate, while a long single-story ranch needs more outlets or 6 in sooner.

Is a 5 inch or 6 inch gutter better for my house?

A 6 in K-style carries 44% more than a 5 in at the same slope, 7,960 against 5,520 sq ft at 1 in/hr. It costs more per foot and needs larger downspouts, so it pays only where a gutter size calculator check puts the 5 in above about 85%.

Gutters running above 85% of gutter size calculator capacity overflow easily once leaves, ice or a sagging hanger cut the flow.

The 2,000 sq ft ranch at 4 in/hr sits at 87% with 5 in gutters and one outlet per eave. Adding the downspouts drops it to 29%, which costs less than upgrading the whole run to 6 in.

What is a standard size for gutters?

The standard residential gutter is 5 in K-style, with 6 in K-style common on large or steep roofs. Half-round gutters come in 4 to 8 in, and the IPC table starts at 3 in half-round, which drains only 170 sq ft at 4 in/hr.

A 4 in half-round drains only 360 sq ft at 4 in/hr, so it suits porches and sheds rather than houses. A 5 in K-style drains 1,380 sq ft at the same rainfall, nearly four times as much, which is why 4 in gutters lose to 5 in on almost any home.

Half-Round Runs Two Sizes Behind K-Style

In sizing gutters and downspout chart terms, a 5 in K-style drains as much as a 7 in half-round, and a 6 in K-style matches an 8 in half-round. The flat bottom and ogee face give K-style more water depth at the same top width.

Design Roof Area at 4 in/hrK-Style NeededHalf-Round Needed
500 sq ft5 in5 in
800 sq ft5 in6 in
1,000 sq ft5 in7 in
1,500 sq ft6 in8 in
2,000 sq ftOver 6 inOver 8 in

Level-pitched at 1/16 in per ft, one outlet. Half-round gutters are chosen for older and historic homes, and a half-round gutter size calculator check usually lands one or two sizes above the K-style answer for the same roof.

Past 2,000 sq ft of design area at 4 in/hr, neither style handles one run alone. Add an outlet to split the run, steepen the slope or move to a box gutter, and on low-slope roofs the Scupper Size Calculator sizes the wall outlets instead.

Cost of 20, 30 and 60 Foot Runs

At an example installed price of $8 per ft and $60 per downspout, a 20 ft gutter run costs $220 and a 60 ft run costs $600. Prices vary by material and region, so set your own rates before comparing quotes.

Gutter RunDesign Area DrainedDownspouts (2 × 3 in)Example Installed Cost
20 ft330 sq ft1$220
24 ft396 sq ft1$252
30 ft495 sq ft1$300
40 ft660 sq ft2$440
60 ft990 sq ft2$600

Gutter size calculator values for a roof 15 ft deep at 6:12, 4 in/hr rainfall, with a downspout at least every 40 ft. Every run in the table needs only a 5 in K-style, so the cost differences come from length and outlets alone.

How much is a 20 ft gutter?

About $160 for 20 ft of gutter at $8 per ft installed, plus $60 for its single downspout, or $220 in all at the example rates. A 24 ft run is $252, a 30 ft run $300 and a 60 ft run $600 with its second downspout.

Downspouts add up faster than gutter on short runs in a gutter size calculator cost. At 40 ft, the second outlet needed for 660 sq ft of roof adds $60 to a $320 gutter, about a sixth of the job, while a 3 × 4 in downspout would cover it alone.

Gutters hang under the drip edge, so a roof job that replaces both can count the trim with the Drip Edge Calculator along the same eave lengths.

UK, Australia and New Zealand Work in mm/hr

A rainfall of 100 mm/hr is 3.94 in/hr, so a 5 in K-style drains about 130 m² of design roof area at that rate. Each m² at 100 mm/hr sheds 0.028 L/s, so 100 m² gives 2.78 L/s.

Converted K-style figures at 100 mm/hr give about 130 m² for 5 in and 188 m² for 6 in, level-pitched with one outlet. At 75 mm/hr, closer to many UK design rates, the 5 in figure rises to about 174 m².

Outside the US, local rules set the gutter size calculator method. A gutter size calculator for Australia or New Zealand should follow AS/NZS 3500.3, and UK work follows BS EN 12056-3, both with their own gutter profiles and rainfall return periods.

Those standards use quad, ogee and box profiles that differ from US K-style, so treat a US gutter size calculator UK or NZ result as a cross-check. The rainfall and roof-area steps carry over directly.