Ice and water shield calculator for eave barrier width by roof pitch under IRC R905.1.2, rows of 36 in membrane, valley and edge strips, laps, roll counts, and whole-deck coverage.
Distances are level. Wall thickness is added for the stricter reading of the code; enter 0 for the literal minimum.
Code Reach, Laps & Other Edges
Waste, Price & Currency
Ice Barrier Diagram
Ice and Water Shield Chart
| Roof Pitch | Barrier Width | Eave Rows | Rolls | Cost |
|---|---|---|---|---|
| 3:12 | 43.3 in | 2 | 4 | $460.00 |
| 4:12 | 44.3 in | 2 | 4 | $460.00 |
| 5:12 | 45.5 in | 2 | 4 | $460.00 |
| 6:12 | 47.0 in | 2 | 4 | $460.00 |
| 7:12 | 48.6 in | 2 | 4 | $460.00 |
| 8:12 | 50.5 in | 2 | 4 | $460.00 |
| 9:12 | 52.5 in | 2 | 4 | $460.00 |
| 10:12 | 54.7 in | 2 | 4 | $460.00 |
| 12:12 | 59.4 in | 2 | 4 | $460.00 |
Step-by-Step Ice Barrier Math
24 Inches Past the Wall: Ice and Water Shield Calculator Widths by Pitch
A 6:12 roof with a 12 in overhang and a 6 in wall needs ice barrier 47.0 in up the slope from the eave edge. That is wider than one 36 in roll, so the ice and water shield calculator answer for that eave is two rows, not one.
The width starts as a level run of overhang plus wall plus 24 in, here 42 in. Pitch then stretches that run along the slope, and every ice and water shield calculator estimate for eaves begins from this sloped width.
W is the barrier width up the slope in inches, O the level eave overhang, T the exterior wall thickness and p the rise per 12 in of run. On roofs of 8:12 and steeper, W is never less than 36 in.
| Roof Pitch | Slope Factor | Barrier Width | Rows of 36 in Roll | Installed Width | Rolls of 200 sq ft |
|---|---|---|---|---|---|
| 3:12 | 1.031 | 43.3 in | 2 | 68.5 in | 4 |
| 4:12 | 1.054 | 44.3 in | 2 | 68.5 in | 4 |
| 6:12 | 1.118 | 47.0 in | 2 | 68.5 in | 4 |
| 8:12 | 1.202 | 50.5 in | 2 | 68.5 in | 4 |
| 10:12 | 1.302 | 54.7 in | 2 | 68.5 in | 4 |
| 12:12 | 1.414 | 59.4 in | 2 | 68.5 in | 4 |
This ice and water shield chart assumes a 100 ft eave, 24 ft of valleys, 8 ft of other edges, a 12 in overhang, a 6 in wall, 3.5 in side laps, 6 in end laps and 10% waste. Pitch moves the width by 16 in, yet the roll count never changes.
The second row is the reason, and it is the step most ice and water shield calculator shortcuts skip.
Two 36 in rows lapped 3.5 in cover 68.5 in, so any width between 36 and 68.5 in buys the same membrane. Pitch only matters for the purchase when it pushes the width past one of those steps.
How do you calculate ice and water shield?
Find the sloped barrier width, divide it into 36 in rows with a 3.5 in lap, then multiply the rows by the eave length.
Add one 36 in strip per foot of valley in the ice and water shield calculator for roof edges, rake wall or skylight edge, add 6 in for each splice where a run is longer than one roll, add waste and divide by the roll length.
For the 6:12 roof above, 2 rows × 100 ft + 24 ft of valleys + 8 ft of other edges is 232 ft of membrane. Each 100 ft row needs one splice in a 66.7 ft roll, adding 1 ft of end lap, and with 10% waste the 233 ft becomes 256.3 ft, or 4 rolls.
What is an ice and water shield calculator?
An ice and water shield calculator is a roll count for self-adhered membrane at eaves, valleys and other leak-prone edges. It rests on the IRC R905.1.2 eave rule and the roll's real coverage after laps, and the 2026 versions use the same rule.
Roof pitch feeds every ice and water shield calculator result, so measure it first or work it out with the Roof Pitch Calculator. A 6:12 and an 8:12 roof differ by 3.5 in of barrier width on a 42 in run.
Rows Double Sooner Than Most Roofers Expect
In ice and water shield calculator terms, one 36 in row covers a typical eave only when the overhang is very short. With a 6 in wall and the 24 in inside reach, a single row works at 6:12 only if the overhang is 2 in or less.
| Level Overhang | 4:12 | 6:12 | 8:12 | 10:12 | 12:12 |
|---|---|---|---|---|---|
| 0 in | 1 row (31.6 in) | 1 row (33.5 in) | 2 rows (36.1 in) | 2 rows (39.1 in) | 2 rows (42.4 in) |
| 6 in | 2 rows (37.9 in) | 2 rows (40.2 in) | 2 rows (43.3 in) | 2 rows (46.9 in) | 2 rows (50.9 in) |
| 12 in | 2 rows (44.3 in) | 2 rows (47.0 in) | 2 rows (50.5 in) | 2 rows (54.7 in) | 2 rows (59.4 in) |
| 18 in | 2 rows (50.6 in) | 2 rows (53.7 in) | 2 rows (57.7 in) | 2 rows (62.5 in) | 2 rows (67.9 in) |
| 24 in | 2 rows (56.9 in) | 2 rows (60.4 in) | 2 rows (64.9 in) | 3 rows (70.3 in) | 3 rows (76.4 in) |
Rows of 36 in membrane with 3.5 in side laps, 6 in wall and 24 in inside the wall. Each extra row adds 32.5 in of coverage, so the third row in an ice and water shield calculator count starts once the width passes 68.5 in.
The largest level run one row can cover is 36 in divided by the slope factor. That is 34.2 in at 4:12, 32.2 in at 6:12, 30.0 in at 8:12 and only 25.5 in at 12:12, so steep roofs with any overhang always need two rows.
How many rows of ice and water shield do I need?
Most houses need two rows at the eaves. A 12 in overhang on a 6 in wall gives a 47.0 in width at 6:12, and the two lapped rows cover 68.5 in, or 21.5 in more than the code line.
Three rows appear in an ice and water shield calculator count with deep overhangs on steep roofs, such as a 24 in overhang at 10:12, which needs 70.3 in.
Grace also suggests a double layer along the eaves in severe ice-dam areas, beyond the code minimum.
The barrier goes as far up the roof as the rows in the count reach, measured along the slope. Water can back up higher than the code line on low roofs with deep snow, so the extra width a second row leaves is useful rather than waste.
Square-Foot Shortcuts Come Up One Roll Short
Dividing barrier area by 200 sq ft per roll under-buys by a roll on most eaves, a gap any ice and water shield calculator for roofing should close.
On the 6:12 roof above, the area shortcut gives 536 sq ft and 3 rolls, while two full-width rows need 4.
The shortcut treats the 47.0 in width as if membrane could be bought 47 in wide. Real rolls are 36 in, so the second row is a full roll width even when the code needs only 11 in more, and 21.5 in of that row sits above the line.
| Roof Pitch | Area Shortcut | Rolls by Area | Rolls by Real Rows |
|---|---|---|---|
| 4:12 | 511 sq ft | 3 | 4 |
| 6:12 | 536 sq ft | 3 | 4 |
| 8:12 | 568 sq ft | 3 | 4 |
| 12:12 | 650 sq ft | 4 | 4 |
100 ft of eave, 32 ft of valleys and other edges as 36 in strips, 12 in overhang, 6 in wall and 10% waste, with 200 sq ft rolls. The real rows lay down about 734 sq ft of membrane including waste.
Laps widen the gap in an ice & water barrier calculator estimate too. Every splice in a long eave row costs 6 in of end lap, and the square-foot method counts neither those splices nor the 3.5 in side lap between rows.
How much ice & water shield do I need?
For each 100 ft of eave on a typical two-row roof, an ice and water shield calculator count comes to about 220 ft of membrane, or 4 rolls of 200 sq ft, before valleys.
The table below holds the ice and water shield length for common eave totals at 6:12, with a 12 in overhang and 10% waste.
| Total Eave Length | Membrane Length | Rolls of 200 sq ft |
|---|---|---|
| 60 ft | 120 ft | 2 |
| 80 ft | 160 ft | 3 |
| 100 ft | 200 ft | 4 |
| 120 ft | 240 ft | 4 |
| 150 ft | 300 ft | 5 |
| 200 ft | 400 ft | 7 |
Membrane length is two rows times the eave, before the 10% waste the roll count includes. Valleys, rake walls and skylights add their own linear feet on top, covered next.
Valleys, Rakes and Skylights Add Strips, Not Rows
Each foot of valley adds one foot of 36 in membrane, centered so 18 in runs up each side. On the 6:12 example, 24 ft of valleys and 8 ft of other edges add 32 ft, about half a roll, to the 200 ft of eave rows.
Grace's instructions call for the valleys to go in before the eaves, working up from the low point and out from the valley center line.
The valley strip then sits under the eave rows where they meet, so water shed down the valley always runs over a lap, whatever the ice and water shield calculator count.
Valley length for any ice and water shield estimate is the true sloped length, measured from the eave corner to the ridge along the valley line itself.
A plan measurement reads about 6% short at 6:12 and 18% short at 12:12, so measure valleys on the roof or from hip-and-valley rafter math with the Hip Roof Calculator.
Rake walls, chimneys and skylight curbs each add to the ice and water shield length with a strip along each edge where water can pond or wind-drive.
A 2 × 4 ft skylight has 12 ft of edge, and a chimney with a cricket adds its perimeter in the same way.
Metal drip edge goes over the membrane at the eaves, per the Grace data sheet. That order means the eave rows start right at the deck edge, and the Drip Edge Calculator counts the trim that covers them.
Laps Take a Tenth of Every Roll
A 200 sq ft roll covers 179.3 sq ft of roof once 3.5 in side laps and 6 in end laps come off, a loss of 10.4%.
Whole-deck jobs that divide by the printed 200 sq ft run short by two rolls on a 2,000 sq ft roof, the main ice and water shield coverage error.
| Roll Size | Printed Area | Net After Laps | Lost to Laps | Rolls per 1,000 sq ft | Rolls for 2,000 sq ft + 10% |
|---|---|---|---|---|---|
| 36 in × 36 ft | 108 sq ft | 96.2 sq ft | 11.0% | 10.40 | 23 |
| 36 in × 50 ft | 150 sq ft | 134.1 sq ft | 10.6% | 7.46 | 17 |
| 36 in × 66.7 ft | 200 sq ft | 179.3 sq ft | 10.4% | 5.58 | 13 |
| 36 in × 75 ft | 225 sq ft | 201.8 sq ft | 10.3% | 4.96 | 11 |
Net coverage per roll in an ice and water shield calculator is (roll length - 0.5 ft) × (36 in - 3.5 in) ÷ 12. On 2,000 sq ft with 10% waste, 200 sq ft rolls need 13, not the 11 that 2,200 ÷ 200 suggests.
The Grace Ice & Water Shield data sheet lists 36 in rolls 36 ft, 66.6 ft and 75 ft long, giving 108, 200 and 225 sq ft.
How much does a roll of ice and water shield cover?
A standard 200 sq ft roll covers about 179 sq ft of deck in an ice and water shield calculator count, or 66.7 ft of eave in a single 36 in row when no splice is needed.
Ice and water shield is 36 in wide in almost every brand, Grace included, so the length printed on the box decides coverage.
On eaves, think in feet rather than square feet. A 225 sq ft roll runs 75 ft, so a 100 ft eave row still needs a splice and the two-row example takes 4 rolls, while 108 sq ft rolls need 8 for the same eave.
Do I need ice and water shield on the entire roof?
Code asks only for eaves where ice dams are a known problem, plus valley lining where the membrane is used for it. Covering the whole deck makes sense on roofs under 4:12, under metal roofing and in deep-snow areas.
The ice and water shield calculator cost gap is large. A 2,000 sq ft roof takes 13 rolls of 200 sq ft for full coverage, against 4 rolls for eaves and valleys on the 100 ft example, so the whole deck buys about three times the membrane.
Below 2:12, asphalt shingles are not allowed at all under the IRC, and from 2:12 up to 4:12 they need two layers of underlayment. Many roofers lay self-adhered membrane over the full deck on those slopes instead.
How much overlap does underlayment need?
Self-adhered ice and water shield needs at least 3.5 in at side laps and 6 in at end laps, per the Grace data sheet. Each new course shingles over the one below, so water always runs over a lap rather than into it.
Those laps set the second-row math in every ice and water shield calculator result. A second 36 in row brings 32.5 in of width, not 36 in, and each splice where one roll ends and the next begins costs 6 in, so lap sizes belong in every roll count.
Wall Line Readings and the IRC R905.1.2 Minimum
The 2021 IRC section R905.1.2 asks for ice barrier from the eave edge to at least 24 in inside the exterior wall line. On roofs of 8:12 and steeper, it must also reach at least 36 in along the slope.
The wall line can be read two ways, and the ice and water shield code reading chosen changes the row count on short overhangs.
Measuring 24 in from the outside face of the wall gives a level run of overhang + 24 in, while measuring from the inside face adds the wall thickness too, the stricter reading many inspectors expect.
| Overhang and Pitch | From Outside Face of Wall | From Inside Face of 6 in Wall |
|---|---|---|
| 6 in at 4:12 | 31.6 in, 1 row | 37.9 in, 2 rows |
| 6 in at 6:12 | 33.5 in, 1 row | 40.2 in, 2 rows |
| 12 in at 6:12 | 40.2 in, 2 rows | 47.0 in, 2 rows |
| 12 in at 12:12 | 50.9 in, 2 rows | 59.4 in, 2 rows |
On short overhangs the reading decides between one row and two. For the outside-face reading, set the wall thickness to 0, and keep the actual thickness when the local inspector measures from the warm side of the wall.
The 36 in steep-roof rule rarely governs. At 8:12 it beats the wall-line rule only when the level run is under 30 in, as with no overhang and the wall left out, where 28.8 in rises to 36 in.
In metric ice and water shield calculator terms, 24 in is 610 mm and a roll is 914 mm wide. A 300 mm overhang and 150 mm wall at 6:12 need 1,185 mm of barrier, which still means two rows.
Is ice and water shield required by code?
Under the IRC, an ice barrier is required on shingle and other steep-slope roofs where the local jurisdiction records a history of ice forming at the eaves, marked in its Table R301.2.
Warm regions mark it as not required, and no national ice and water shield map replaces that local table.
Where it is required, the barrier must be self-adhering polymer-modified bitumen or two layers of cemented underlayment, starting at the lowest edge of every roof surface. Detached accessory buildings without conditioned floor area are exempt.
What's the difference between ice and water shield and regular underlayment?
Ice and water shield sticks to the deck and seals around every nail, so water backing up under shingles cannot follow the fasteners. Felt and synthetic underlayment are mechanically fastened and shed water only when it flows downhill.
That seal is why an ice and water shield calculator only counts the places where ice dams and valleys hold water. The Grace sheet stays flexible down to -20 °F, but it must be installed at 40 °F or warmer and covered within 90 days.
Pricing by the Foot of Eave
At an example ice and water shield calculator price of $115 per 200 sq ft roll, the 100 ft two-row eave with its valleys costs $460 in membrane, or $4.60 per foot of eave. Prices vary by brand and supplier, so set your own roll price.
Roll size changes the ice and water shield calculator buy more than the price per square foot suggests. The same 100 ft eave job needs 8 rolls of 108 sq ft, 6 of 150 sq ft, 4 of 200 sq ft or 4 of 225 sq ft, because each roll is cut into eave runs.
Leftover membrane from an ice and water shield calculator count goes to vents, pipe boots and skylight corners. The 4 rolls in the example leave 10.5 ft spare, enough for several flashing patches without buying a fifth roll.
A roof ice shield cost calculator estimate for a whole deck scales with area instead. The Roofing Calculator gives the sloped roof area, and 5.58 rolls per 1,000 sq ft of 200 sq ft roll turns that into a buy.
Shingle bundles follow the same area as a whole-deck membrane count, and the Roof Shingle Calculator counts them, so the ice and water shield calculator roll count and the shingles can go on one supplier order.