Roof Tile Spacing Calculator

Updated

Roof Tile Spacing Calculator for even batten gauge from rafter length, tile length and headlap, with batten set-out marks, plain or interlocking tile counts, battens and fasteners.

Quick Setup

Measure along the top of the rafter from the fascia line up to the ridge.

Tile Type and WidthSingle-lap, 11.625 in cover

Cover width is the width one tile adds to a course after side interlock. Light tile and snow areas need more nails.

Eave and Ridge Setout2 in overhang, 2 in top gap

Measure along the slope. The lug offset runs from the top of the tile to the face that hooks the batten.

Slopes, Waste and Battens2 slopes, 10% waste

A gable roof has two slopes and four rake edges; a hip roof has none. Waste covers cuts and breakage.

slopes
%
edges
Roof Tile Spacing
13 9/16 in Batten Gauge
13 equal gauges · headlap 3.44 in
14 Batten Rows per Slope
First Batten from Fascia13 3/4 in
Top Batten from Fascia15 ft 10 in
Each batten row holds one tile course, counting the first batten at the eave and the top batten.
1,294 Tiles to Order
Tiles per Course42 tiles
Tiles per Square91.4
Courses times tiles per course on every slope, plus waste. The per-square count uses your gauge.
1,120 ft of Battens
Battens to Buy, 8 ft154 pcs
Batten per Square88.5 ft
Batten rows times course length on every slope. The stock count adds your waste to the batten run.
904 Tile Fasteners
NailingEdges + every other tile
Underlay1 layer of felt
Tile nails set by roof pitch and tile weight per the tile fastening table. Waste tiles are excluded.
Batten Count OptionsFewest rows that keep the headlap
Batten RowsGaugeHeadlapTiles per Slope
1314.69 in2.31 in short546
14 (yours)13.56 in3.44 in588
1512.59 in4.41 in630
1611.75 in5.25 in672
1711.02 in5.98 in714
Batten Setout MarksTop edge of each batten
BattenFrom FasciaFrom First Batten
First13 3/4 in0 in
22 ft 3 5/16 in13 9/16 in
33 ft 4 7/8 in2 ft 3 1/8 in
44 ft 6 7/16 in3 ft 4 11/16 in
55 ft 8 in4 ft 6 1/4 in
66 ft 9 9/16 in5 ft 7 13/16 in
77 ft 11 1/8 in6 ft 9 3/8 in
89 ft 5/8 in7 ft 10 7/8 in
910 ft 2 3/16 in9 ft 7/16 in
1011 ft 3 3/4 in10 ft 2 in
1112 ft 5 5/16 in11 ft 3 9/16 in
1213 ft 6 7/8 in12 ft 5 1/8 in
1314 ft 8 7/16 in13 ft 6 11/16 in
Top15 ft 10 in14 ft 8 1/4 in
Tile and Batten Order List1,294 tiles, 154 battens
ItemOrderBased On
Field tiles1,29414 courses × 42 × 2 slopes + 10%
Rake tiles5614 courses × 4 rake edges
Battens, 1x2 min1,120 ft14 rows × 40 ft × 2
Batten stock154 pcs1,120 ft + 10% ÷ 8 ft
Batten nails, 8d58824 in (610 mm) on center per row
Tile fasteners904Edges + every other tile
Underlayment1 layer of feltSet by roof pitch
Step-by-Step Math6 steps with your numbers
  1. Max gauge: 17 - 3 = 14 in
  2. First batten: 17 - 1.25 - 2 = 13.75 in up from the fascia
  3. Batten span: 192 - 13.75 - 2 = 176.25 in
  4. Gauges: 176.25 ÷ 14 = 12.589 → 13 (round up)
  5. Even gauge: 176.25 ÷ 13 = 13.558 in, headlap 17 - 13.558 = 3.442 in
  6. Tiles: 480 ÷ 11.625 → 42 per course × 14 rows × 2 = 1,176 + 10% → 1,294
Batten Setout Ready
Mark the first and top battens, then step the even gauge between them. Never stretch a gauge past the max.

Batten Gauge Math Behind a Roof Tile Spacing Calculator

Batten gauge is the tile length minus the minimum headlap, then reduced so every course between the first and top battens is equal. A 17 in tile with 3 in headlap on a 16 ft rafter sets out at 13 9/16 in, 14 batten rows per slope.

In roof tile spacing calculator math, S is the batten span from the first batten to the top batten, T the tile length and H the minimum headlap. n is the number of equal gauges, rounded up, and g the gauge actually used, with n + 1 batten rows.

Rounding up is the safety rule. That 176 1/4 in span divided by a 14 in maximum gauge is 12.59, so it takes 13 gauges of 13.56 in, and the headlap grows from 3 in to 3.44 in instead of shrinking.

Metric roofs follow the same roof tile spacing calculator steps. A 420 mm interlocking tile with 75 mm headlap has a 345 mm maximum gauge, so a 3,800 mm span needs 12 gauges of 316.7 mm, giving 103 mm of headlap.

That roof tile spacing calculator result surprises people. The span is only 5 mm longer than 11 gauges of 345 mm, but stretching to 345.5 mm would break the headlap, so the whole roof drops to 316.7 mm.

The same metric setout answers a roof tile spacing calculator India search, where clay and concrete tiles go on battens in millimeters. Only the tile length and the maker's headlap change the numbers.

Rows Versus Headlap: Picking the Batten Count

Adding a batten row shortens the gauge and raises the headlap, at the cost of one more tile course per slope. On the 16 ft rafter, 14 rows is the fewest that keep 3 in of headlap.

Batten rowsGaugeHeadlapTiles per slope
1314.69 in2.31 in, too short546
1413.56 in3.44 in588
1512.59 in4.41 in630
1611.75 in5.25 in672
1711.02 in5.98 in714

Each extra row in a roof tile spacing calculator count costs 42 tiles per slope on a 40 ft eave. Extra headlap helps on low pitches, so 15 rows can be worth 84 more tiles near the bottom of a tile's pitch range.

Roof tile gauge never goes above the maximum to save a course. Marley warns that exceeding the maximum gauge leaves too little headlap and can void the tile warranty.

Plain Tiles Versus Interlocking: Gauge and Count per m²

Double-lap plain tiles use half the usual gauge, because each tile laps the course two below it. A 265 mm plain tile with 65 mm headlap has a 100 mm gauge, (265 - 65) ÷ 2, about 10 battens per meter of rafter.

TileLengthHeadlapMax gaugeBatten per m² of roofTiles per m²
Plain, 165 mm wide265 mm65 mm100 mm10.0 m60.6
Interlocking, 295 mm cover17 in (432 mm)3 in (76 mm)14 in (356 mm)2.9 m at 344 mm9.8 at 344 mm
Interlocking, 420 mm420 mm75 mm345 mm3.2 m at 316.7 mmSet by cover width

Batten per m² in roof tile spacing calculator terms is 1,000 ÷ gauge in mm, so how much batten per m² plain tiles take is about 10 m, against roughly 3 m for interlocking. That answers how many roof battens per m² before laps and waste.

Tiles per m² is 1,000,000 ÷ (gauge × cover width) in mm. Plain tiles land near 60 per m², while a 295 mm cover interlocking tile at 344 mm gauge needs about 9.8, so the tile type changes the count six times over.

Marley sets the plain tile maximum at 100 mm with a 65 mm minimum headlap, and 75 to 100 mm for interlocking tiles depending on pitch. A roof tile spacing calculator figure is only as good as the headlap the maker sets for your pitch.

Eave and Ridge Setout: First and Top Batten

In a roof tile spacing calculator setout, the first batten sits one tile length, less the lug offset and the overhang, up from the fascia. A 17 in tile with a 1 1/4 in lug offset and 2 in overhang puts its top edge 13 3/4 in up the rafter.

Marley sets the tile tail at least 50 mm over the fascia and the top batten below the ridge by the nib depth plus 5 to 15 mm. The ridge tiles must then cover the top course by at least 75 mm.

BattenTop edge from fasciaBattenTop edge from fascia
First1 ft 1 3/4 in89 ft 5/8 in
22 ft 3 5/16 in910 ft 2 3/16 in
33 ft 4 7/8 in1011 ft 3 3/4 in
44 ft 6 7/16 in1112 ft 5 5/16 in
55 ft 8 in1213 ft 6 7/8 in
66 ft 9 9/16 in1314 ft 8 7/16 in
77 ft 11 1/8 inTop15 ft 10 in

Mark the first and top battens on every rafter, then step the gauge between them. Marks taken from the fascia each time stop small errors from adding up, which a running tape measured batten to batten does not.

The rafter length itself comes from run and pitch. The Rafter Length Calculator gives it with overhang, and the Roof Pitch Calculator converts a tile maker's minimum pitch in degrees to x/12.

Sizes, Lengths and Nails for Roof Battens

Marley specifies 38 × 25 mm battens for rafters at up to 450 mm centers and 50 × 25 mm at up to 600 mm for single-lap tiles. Every batten should be at least 1.2 m long so it spans three rafters.

A roof tile spacing calculator order for the 40 ft gable is 1,120 ft of batten, 14 rows × 40 ft × 2 slopes, or 154 pieces of 8 ft stock with 10% extra. Nailed at every 24 in rafter, that is 588 batten nails.

Batten per square in a roof tile spacing calculator is 1,200 ÷ gauge in inches, or 88.5 ft at 13.56 in. Roof batten spacing for clay roof tiles follows the same rule, since clay and concrete differ in weight and lap, not in setout.

Joints need care too. For gauges over 200 mm, Marley allows no more than one batten in four courses to be joined over the same rafter, so stagger the 8 ft lengths as they go on.

Fastening Tiles by Pitch and Weight

On battens, IRC Table R905.3.8 needs no fasteners away from the edges below 5/12, one per tile in every other row from 5/12 to 12/12, and one per tile from 12/12 to 24/12.

Perimeter tiles, three courses but not less than 36 in from each edge, are always fastened, at every pitch and on every tile weight.

40 ft gable, 14 rowsRuleTile fasteners
4/12, 9 psf or morePerimeter tiles only632
6/12, 9 psf or morePerimeter plus every other row904
12/12, 9 psf or moreEvery tile1,176
6/12, under 9 psfEvery tile1,176
Over 24/12Head and nose of every tile2,352

Lightweight tile under 9 psf takes one fastener per tile at any pitch, which adds 272 fasteners to the roof tile spacing calculator count on the 6/12 roof.

In snow areas the code asks for two fasteners per tile, or battens plus one, so a battened roof there fastens every tile, the same 1,176 on this roof.

The perimeter band and the nose fastening past 24/12 both come from the footnotes to the tile attachment table, as printed in the Massachusetts building code. On 4 in plain tile gauges, 36 in means 9 courses, not 3.

Tile needs at least 2.5/12 under IRC R905.3.2, with two underlayment layers up to 4/12, per the California Residential Code text of R905.3. A flat roof tile spacing calculator answer below that pitch is no tile at all.

Tile weight drives the framing too. Clay and concrete tile add far more dead load than asphalt shingles, so check the rafters with the Roof Weight Calculator before a reroof from asphalt.

Tile Counts, Squares and Spacing

Roof tile spacing calculator answers below use the 17 in tile, 3 in headlap and 11 5/8 in cover width from the examples above, unless a question names other sizes.

How do I calculate the correct spacing for roof tiles?

Subtract the maker's minimum headlap from the tile length for the maximum gauge, divide the batten span by it, round up, and divide the span by that whole number. Marley's interlocking example runs from 320 to 345 mm, about 12 1/2 to 13 1/2 in.

A 3,800 mm span with 345 mm tiles gauges at 316.7 mm, while plain tiles sit at 100 mm. The spacing between tiles across the course is fixed by the interlock, so only the batten gauge is set on site.

What is a roof tile spacing calculator?

It is a setout aid that turns rafter length, tile length and headlap into an even batten gauge, the number of rows and the mark for every batten. It also counts tiles and battens from the gauge.

The useful part is the even gauge. Dividing by the maximum gauge alone leaves a short last course at the ridge, while an even gauge keeps every course the same and the headlap at or above the minimum.

How do you calculate the number of tiles on a roof?

In roof tile spacing calculator math, multiply batten rows by tiles per course, then by the number of slopes, and add waste. Fourteen rows of 42 tiles on two slopes is 1,176 tiles, or 1,294 with 10% waste.

A gable's 4 rake edges add one rake tile per course, 56 more for 14 rows, ordered as a separate line from the field tiles.

As a tile calculator square feet figure, the same tile works out to about 91 tiles per 100 sq ft, 14,400 ÷ (13.56 × 11.625). For a single room's roof, measure that slope's area and scale from 91 per 100 sq ft.

How many roof tiles per sq meter?

Interlocking tiles run about 9.8 per m² at a 344 mm gauge and 295 mm cover, while plain tiles run about 60 per m² at 100 mm gauge and 165 mm width. The count is 1,000,000 ÷ (gauge × cover) in mm.

A tile calculator m2 figure from a product brochure assumes its own gauge. If your even gauge comes out shorter, the count per m² rises, so recompute it from your setout gauge.

How many squares is a 30x40 roof?

A 30 × 40 ft footprint is 12 squares flat, but at 6/12 the roof surface is 1,342 sq ft, or 13.42 squares. With the roof tile spacing calculator example tile at 91.4 per square, that is about 1,227 tiles before waste.

The pitch factor, 1.118 at 6/12, is what turns footprint into roof area. The Gable Roof Area Calculator works it out with overhangs included.

How do you calculate the total area covered by tiles?

Multiply the tile count by the gauge and the cover width. The 1,294 tiles ordered for the 40 ft gable cover 1,294 × 13.56 × 11.625 ÷ 144 = 1,416 sq ft, including the 10% spare.

Tile area calculator results use the exposed area per tile, not the full tile size. The full 17 in tile covers more board, but the headlap hides 3.44 in of it on every course.

What is the 3/4/5 rule for tile?

The 3-4-5 rule squares a layout line by making a right triangle with sides of 3, 4 and 5 units. On a roof, mark 3 ft along the eave and 4 ft up the rafter; when the diagonal reads exactly 5 ft, the line is square.

Scaling to 6, 8 and 10 ft improves accuracy on long eaves. A square vertical line keeps tile columns straight up the slope, while the roof tile spacing calculator gauge keeps the courses even.