Stucco Calculator

Updated

Stucco calculator for 2-coat and 3-coat walls that turns wall area or house size into base coat and finish coat bags, cement and sand, water, weight and an installed cost estimate.

Wall and Stucco Setup

Measure every wall to be stuccoed, then subtract doors and windows larger than a few square feet.

%
floors
Coat Thickness and Bag Yield3-coat, 7/8 in
parts
Stucco Prices and Labor$14.00/bag, $6.00/sq ft labor
$/bag
$/bag
$/bag
$/ton
Stucco Needed
33 Bags of Base Coat Stucco
In 80 lb bags, plus 6 finish coat bags of 80 lb
12 sq ft per Bag at 3/4 in
Base Bags per 100 sq ft8.33
Material per sq ft8.86 lb
Coverage falls as base coats get thicker. One bag spreads half as far at 3/4 in as it does at 3/8 in.
1.05 cu yd Mixed Stucco
Total Material Weight3,120 lb
Mixing Water57.4 gal
Volume covers every coat plus waste. Water is about 5 1/2 quarts per 80 lb base bag and 2 gallons per finish bag.
$594.00 Material Cost
Installed Estimate$2,706.00
Installed per sq ft$7.69
Material cost uses whole bags with waste. The installed estimate adds your labor rate on the net wall area.
352 sq ft Net Stucco Area
Gross Wall Area400 sq ft
Area with Waste387.2 sq ft
Net area takes doors and windows off the gross wall. Waste is added on top for scratching, drops and corners.
Stucco Coats Diagram7/8 in total
Finish Coat, 1/8 in5.5 finish bagsBrown Coat, 3/8 in16.1 bagsScratch Coat, 3/8 in16.1 bagsLath and Wall Sheathing
Stucco Coverage by ThicknessFor 387.2 sq ft with waste
Base ThicknessPer 80 lb BagPremix BagsPer Cement BagCement Bags
1/4 in36 sq ft11150 sq ft3
3/8 in24 sq ft17100 sq ft4
1/2 in18 sq ft2275 sq ft6
5/8 in14.4 sq ft2760 sq ft7
3/4 in12 sq ft3350 sq ft8
7/8 in10.29 sq ft3842.9 sq ft10
1 in9 sq ft4437.5 sq ft11
Step-by-Step Stucco Math10 steps
Wall area40 ft × 10 ft = 400 sq ft
Net area400 - 48 = 352 sq ft
Area with waste352 × 1.1 = 387.2 sq ft
Base thickness3/8 in + 3/8 in = 3/4 in
Bag coverage0.75 cu ft × 80 ÷ 80 = 0.75 cu ft ÷ (0.75 in ÷ 12) = 12 sq ft per bag
Base coat bags387.2 ÷ 12 = 32.27, rounded up to 33
Finish coat bags387.2 ÷ (70 × 1/8 in ÷ 1/8 in = 70) = 5.53, rounded up to 6
Total weight33 × 80 lb + 6 × 80 lb = 3,120 lb
Material cost33 × $14.00 + 6 × $22.00 = $594.00
Installed estimate$594.00 + 352 sq ft × $6.00 = $2,706.00
Mist-Cure Each Base Coat
Keep each base coat damp with a fine mist once it reaches final set, and let it cure before the next coat. Weather sets the wait, so follow the bag instructions.

Coat Thickness Drives Every Stucco Calculator Bag Count

An 80 lb bag of base coat stucco covers 24 sq ft at 3/8 in but only 12 sq ft at 3/4 in. A three-coat wall builds 3/4 in of base before the finish, so its stucco calculator bag count doubles against a single 3/8 in coat.

In stucco calculator math, N is the number of bags, A is the net wall area in square feet, w is the waste allowance as a decimal, t is the total base coat thickness in inches and Y is the bag yield in cubic feet. The 12 turns inches into feet.

The Quikrete Scratch and Brown Base Coat Stucco data sheet puts the yield at about 0.75 cu ft per 80 lb bag. It lists 20 to 24 sq ft at 3/8 in, 15 to 18 at 1/2 in and 10 to 12 at 3/4 in, which matches stucco calculator math at the top of each range.

A 40 × 10 ft wall with 48 sq ft of windows and doors leaves 352 sq ft to cover. With 10% waste that becomes 387.2 sq ft. A stucco calculator count for two 3/8 in base coats is 387.2 × 0.75 ÷ 12 ÷ 0.75 = 32.27, so 33 bags.

The finish coat gets its own stucco calculator line because it is thinner and uses a different bag. The Quikrete Finish Coat Stucco data sheet gives about 70 sq ft per 80 lb bag at 1/8 in, so the same wall takes 5.53 bags, rounded to 6.

Base Coat Thicknesssq ft per 80 lb BagBags per 100 sq ftsq ft per 94 lb Cement Bag, 3 Parts Sand
1/4 in362.78150
3/8 in244.17100
1/2 in185.5675
5/8 in14.46.9460
3/4 in128.3350
7/8 in10.299.7242.9
1 in911.1137.5

One bag of stucco coverage quoted without a thickness means little. The common "24 sq ft per bag" figure holds only at 3/8 in, so a stucco calculator how many bags estimate built on it for a 3/4 in base runs half short.

For a stucco calculator estimate in smaller bags, a 60 lb bag of the same mix yields three quarters as much, 0.5625 cu ft. At 3/4 in it covers 9 sq ft, so the 387.2 sq ft wall needs 44 bags of 60 lb instead of 33 bags of 80 lb.

Bags of Stucco per 100 sq ft and per m²

Three-coat stucco takes 8.33 bags of 80 lb base coat and 1.43 bags of finish per 100 sq ft, before waste. In a two-coat stucco calculator estimate over block or concrete, the base halves to 4.17 bags, with the same 1.43 bags of finish.

SystemBase Coats80 lb Base Bags per 100 sq ft80 lb Finish Bags per 100 sq ft94 lb Cement Bags per 100 sq ftSand per 100 sq ft
3-coat over lath3/8 + 3/8 in8.331.4326 cu ft
2-coat over masonry3/8 in4.171.4313 cu ft

Stucco per sq ft works out to 0.083 bags of 80 lb base mix for a three-coat wall, or about 6.7 lb of dry base mix per square foot. The finish adds about 1.1 lb per square foot at 1/8 in.

In metric, an 80 lb bag yields about 21.2 L. At 10 mm that covers 2.12 m², so a stucco calculator square feet figure converts to 4.71 bags per 10 m² for one coat, or 8.95 bags per 10 m² for a 19 mm three-coat base.

Base Thicknessm² per 80 lb BagBags per 10 m²
6 mm3.542.83
10 mm2.124.71
13 mm1.636.12
16 mm1.337.53
19 mm1.128.95
25 mm0.8511.77

Stucco calculator waste goes on top of these rates. Stucco drops off the hawk, fills the lath keys and builds up at corners, so 10% is a working minimum, and a stucco wall calculator figure for a heavily cut-up elevation needs more.

Scratch, Brown and Finish Coat Quantities

On the 352 sq ft example wall, the scratch coat and the brown coat each take about 16.1 bags of 80 lb base mix, and the finish takes 5.5 bags. A stucco calculator order split by coat helps, because the coats go on a week or more apart.

The IRC calls for at least three coats over metal or wire lath and at least two over masonry or concrete, according to the exterior plaster rules printed in Minnesota Rules 1309.0703, which adopt the IRC text.

CoatThickness80 lb Bags, ExactMixed Volume
Scratch3/8 in16.1312.1 cu ft
Brown3/8 in16.1312.1 cu ft
Finish1/8 in5.534 cu ft
Total7/8 in33 base + 6 finish bags1.05 cu yd

A scratch coat stucco calculator count can come out low if the lath is ignored. The scratch coat has to push through and embed the lath.

Actual use on the first coat often runs past the 3/8 in figure, which is why the waste allowance belongs in the base count rather than only on the finish.

Base coats thinner than 3/8 in crack and can leave lath showing, and the Quikrete base coat sheet gives no coverage below that thickness. A two-coat wall over block, at 3/8 in base and 1/8 in finish, needs 17 base bags and 6 finish bags for the same 352 sq ft.

Finish bags scale with finish thickness. At 3/16 in one 80 lb finish bag covers 46.7 sq ft, and at 1/4 in only 35 sq ft, so a heavy texture can double the finish order compared with a smooth 1/8 in coat.

Premix Bags or Site-Mixed Cement and Sand

The 352 sq ft three-coat wall takes 33 premix base bags, or 8 bags of 94 lb plastic cement with 24 cu ft of sand. Site mixing cuts the stucco calculator bag count but moves the work of batching sand to the crew.

The Quikrete Plastic Cement data sheet mixes one 94 lb bag with 3 parts sand, five 50 lb bags of plaster sand, for about 3 cu ft of mortar. That covers approximately 100 sq ft at 3/8 in.

Nc is the cement bag count and Yc is the mixed yield of one cement bag, taken from its coverage at 3/8 in. At 100 sq ft per bag, Yc = 100 × 0.375 ÷ 12 = 3.125 cu ft.

Base Mix for 352 sq ft, 3-CoatBagsSandBase Material Weight
80 lb premix base coat33None2,640 lb
94 lb plastic cement, 3 parts sand824 cu ft, 40 bags of 50 lb2,752 lb

Quikrete's stucco mix ratio chart runs 2 1/4 to 5 parts sand for base coats and 1 1/2 to 3 parts for finish coats, with cement meeting ASTM C1328. Leaner mixes stretch each cement bag in a stucco calculator total but cut workability and strength.

Sand is the hidden haul. Eight cement bags at 3 parts need 40 bags of 50 lb plaster sand, a full ton, and that sand must be clean plaster sand to ASTM C897, not fill or play sand.

The same sand and cement ratio work shows up in masonry. The Mortar Calculator handles bags and sand for the brick or block wall that a two-coat stucco job often goes over.

Square Footage From House Size

A one-story 1,500 sq ft house with 9 ft walls has about 1,423 sq ft of exterior wall before windows and doors. Wall area, not floor area, sets every stucco calculator by square footage estimate, and the conversion takes a footprint shape.

Aw is the gross wall area, L and W are the footprint length and width, h is the wall height per story and s is the number of stories. The footprint is the floor area divided by the story count.

In a stucco calculator house estimate, 1,500 sq ft as a 1.5 to 1 rectangle gives a footprint of 47.4 × 31.6 ft. Its perimeter is 158.1 ft, and 158.1 × 9 = 1,423 sq ft of wall.

HouseStoriesFootprintPerimeterWall Area, 9 ft Walls
1,200 sq ft142.4 × 28.3 ft141.4 ft1,273 sq ft
1,500 sq ft147.4 × 31.6 ft158.1 ft1,423 sq ft
1,500 sq ft233.5 × 22.4 ft111.8 ft2,013 sq ft
2,000 sq ft154.8 × 36.5 ft182.6 ft1,643 sq ft
3,000 sq ft167.1 × 44.7 ft223.6 ft2,013 sq ft
3,000 sq ft247.4 × 31.6 ft158.1 ft2,846 sq ft

Floor area is a poor stucco calculator input on its own. A two-story 3,000 sq ft house carries 2,846 sq ft of wall, 41% more than a one-story house of the same floor area, because it has twice the wall height on a smaller footprint.

Shape moves the number less than stories do. A 1,500 sq ft square footprint gives 1,394 sq ft of wall and a 2 to 1 rectangle gives 1,479, a 6% spread. Gables, bump-outs and garage walls add more, so measured walls beat any floor-area estimate.

Subtract windows and garage doors from the gross stucco calculator figure. A house with 150 sq ft of openings on 1,423 sq ft of wall leaves 1,273 sq ft of stucco, which trims 14 base bags from a three-coat order.

Cost to Stucco a 1,200, 1,500 or 3,000 sq ft House

Labor drives stucco cost. At $14 per base bag, $22 per finish bag and $6 per sq ft of labor, a one-story 1,500 sq ft house comes to about $10,878, and $8,538 of that is labor.

HouseWall AreaBase + Finish BagsMaterialsLabor at $6/sq ftInstalled
1,200 sq ft, 1 story1,273 sq ft117 + 21$2,100$7,637$9,737
1,500 sq ft, 1 story1,423 sq ft131 + 23$2,340$8,538$10,878
2,000 sq ft, 1 story1,643 sq ft151 + 26$2,686$9,859$12,545
3,000 sq ft, 1 story2,013 sq ft185 + 32$3,294$12,075$15,369
3,000 sq ft, 2 story2,846 sq ft261 + 45$4,644$17,076$21,720

These stucco calculator cost figures assume three coats, 10% waste and no openings removed, and the prices are sample inputs, not market quotes. Swap in local bag prices and a contractor's labor rate, since both vary widely by region.

Stucco price per sq ft quotes are per square foot of wall, not floor. The one-story 1,500 sq ft house works out to $7.64 per sq ft of wall, or $7.25 per sq ft of floor, while the two-story 3,000 sq ft house hits $7.24 per floor sq ft.

Site-mixed base coat cuts the stucco calculator material bill. With 8 cement bags at $18 and sand at $45 a ton, the 1,500 sq ft house's materials drop from $2,340 to about $1,262, yet the installed total only falls about 10% because labor is unchanged.

A stucco estimate calculator total also leaves out lath, two layers of water-resistive barrier, weep screed and scaffolding. Price those as separate lines, since a two-story wall needs scaffold for every coat.

Water, Weight and Cure Time Between Coats

Mixing water follows the stucco calculator bag count, since each 80 lb bag of base coat takes about 5 1/2 quarts of water, so 33 bags need about 45 gallons.

Finish coat takes about 2 gallons per 80 lb bag, or 12 gallons for 6 bags, both per the Quikrete data sheets. Together the wall needs about 57.4 gallons of clean mixing water.

The stucco calculator dry load for the 352 sq ft wall is 33 base bags and 6 finish bags, 3,120 lb in all. That is over a ton and a half of material, so check vehicle payload or arrange delivery before the first coat.

StepMinimum WaitCondition
Any coat before the next48 hours moistKeep damp unless an ASTM C926 exception applies
Scratch to brown, 3-coat48 hoursAfter the first coat
Brown to finish, 3-coat7 daysAfter the second coat
Base to finish, 2-coat7 daysAfter the first coat

Those waits come from the IRC exterior plaster rules in Minnesota Rules 1309.0703. A three-coat stucco calculator schedule therefore spans at least 9 days from scratch to finish, which is why the finish bags can be bought later and color-matched to one batch.

The Quikrete plastic cement and finish coat sheets call for a fine fog spray about twice a day, morning and evening, for several days. The plastic cement sheet also rules out work below 40°F or with freezing expected within 48 hours.

Stucco Exterior Choices and Lifespan

Three common questions follow once the bag count is in hand. The answers use the same stucco calculator wall, house and price figures as the tables.

Is stucco the cheapest material?

Stucco materials are cheap, but the labor is not, which is also why stucco is expensive. On the 1,500 sq ft example house, bags cost $2,340 while labor at $6 per sq ft adds $8,538, so labor is about 78% of the job.

The labor share comes from the process. Three hand-applied coats, a 48-hour wait and a 7-day wait mean a crew returns at least three times, and lath, two barrier layers and weep screed all go on before the first coat.

How to stucco a house exterior?

A three-coat exterior starts with two layers of water-resistive barrier over wood sheathing, then corrosion-resistant metal lath nailed or stapled no more than 6 in apart, per the IRC rules in Minnesota Rules 1309.0703.

A weep screed goes at the foundation plate line, at least 4 in above earth or 2 in above paving. Then come a 3/8 in scratch coat, a 3/8 in brown coat 48 hours later and a 1/8 in finish at least 7 days after that.

Over masonry or concrete, the IRC minimum drops to two coats. The Concrete Block Calculator counts the CMU for a block wall that will get a two-coat stucco finish.

How long will a stucco exterior last?

Stucco lasts as long as water stays out of the wall behind it. The IRC's two barrier layers, the weep screed set 4 in above soil and full 48-hour and 7-day cure times exist to stop the trapped moisture that ends most stucco jobs early.

Coat thickness matters too. A base thinned below 3/8 in to stretch bags cracks sooner, so the 33 bags the example wall needs at full thickness are cheaper over time than 22 bags spread as two 1/4 in coats.