SMD Resistor Code Calculator

Updated

SMD resistor code calculator for 3-digit, 4-digit, EIA-96, R and milliohm marks, with the tolerance range, nearest E-series value and the voltage limit for each case, 0201 to 2512.

SMD Resistor Code

Type the code printed on the SMD resistor, such as 472, 1002, 01C, 4R7 or R010.

Underline, Case Size & Voltage0603 · 5 V
V
4.7 kΩ SMD Resistor
4,700 Ω · code 472 = 47 × 10² Ω
±5% Typical (3-Digit)
Lowest Reading4.465 kΩ
Highest Reading4.935 kΩ
The resistance a good part can measure, from what this code style usually means.
1/10 W Rating (0603)
Max Voltage Here21.7 V
Max Current Here4.61 mA
The most voltage and current this value can take in the chosen case size.
4701 4-Digit Code
Nearest EIA-9666B = 4.75 kΩ
BandsYellow Violet Red
The same value in other SMD marking styles, and as through-hole color bands.
5.32 mW at 5 V
Current Drawn1.06 mA
Safety Factor18.8×
Heat and current with this voltage across the resistor, checked against the case.
How to Read This Marking472
47247Significant digits: 472× 10² (add 2 zeros), in Ω06031/10 W, 75 V max
SMD Resistor Code Chart, 1 Ω to 10 MΩ4.7 kΩ highlighted
Resistance3-Digit4-DigitEIA-96
1 Ω1R01R0001Y
1.5 Ω1R51R5018Y
2.2 Ω2R22R20-
3.3 Ω3R33R30-
4.7 Ω4R74R70-
6.8 Ω6R86R80-
10 Ω10010R001X
15 Ω15015R018X
22 Ω22022R0-
33 Ω33033R0-
47 Ω47047R0-
68 Ω68068R0-
100 Ω101100001A
150 Ω151150018A
220 Ω2212200-
330 Ω3313300-
470 Ω4714700-
680 Ω6816800-
1 kΩ102100101B
1.5 kΩ152150118B
2.2 kΩ2222201-
3.3 kΩ3323301-
4.7 kΩ4724701-
6.8 kΩ6826801-
10 kΩ103100201C
15 kΩ153150218C
22 kΩ2232202-
33 kΩ3333302-
47 kΩ4734702-
68 kΩ6836802-
100 kΩ104100301D
150 kΩ154150318D
220 kΩ2242203-
330 kΩ3343303-
470 kΩ4744703-
680 kΩ6846803-
1 MΩ105100401E
1.5 MΩ155150418E
2.2 MΩ2252204-
3.3 MΩ3353304-
4.7 MΩ4754704-
6.8 MΩ6856804-
10 MΩ106100501F
EIA-96 Code Table & Case Sizes0603 highlighted

EIA-96 Code Index (1% Values)

CodeValueCodeValueCodeValueCodeValue
01100251784931673562
02102261825032474576
03105271875133275590
04107281915234076604
05110291965334877619
06113302005435778634
07115312055536579649
08118322105637480665
09121332155738381681
10124342215839282698
11127352265940283715
12130362326041284732
13133372376142285750
14137382436243286768
15140392496344287787
16143402556445388806
17147412616546489825
18150422676647590845
19154432746748791866
20158442806849992887
21162452876951193909
22165462947052394931
23169473017153695953
24174483097254996976

EIA-96 Multiplier Letters

LetterMultiplier
Z× 0.001
Y or R× 0.01
X or S× 0.1
A× 1
B or H× 10
C× 100
D× 1,000
E× 10,000
F× 100,000

Case Size Ratings at 70 °C

SizeMetricBodyPowerMax VUsual Marking
020106030.6 × 0.3 mm1/20 W25 VUsually unmarked
040210051.0 × 0.5 mm1/16 W50 VUsually unmarked
060316081.6 × 0.8 mm1/10 W75 V3-digit 5%, EIA-96 1%
080520122.0 × 1.25 mm1/8 W150 V3-digit 5%, 4-digit 1%
120632163.2 × 1.6 mm1/4 W200 V3-digit 5%, 4-digit 1%
121032253.2 × 2.5 mm1/2 W200 V3-digit 5%, 4-digit 1%
201050255.0 × 2.5 mm3/4 W200 V3-digit 5%, 4-digit 1%
251263326.35 × 3.2 mm1 W200 V3-digit 5%, 4-digit 1%
Step-by-Step Math9 steps
1. Significant Digits4, 7 → 47
2. Multiplier2 → 10² = 100
3. Resistance47 × 100 = 4,700 Ω
4. Convert4,700 Ω = 4.7 kΩ
5. Tolerance±5% Typical (3-Digit) → 4.465-4.935 kΩ
6. Case Limits0603: 1/10 W (0.1 W), 75 V working limit
7. Max Voltage Here√(0.1 W × 4,700 Ω) = 21.7 V
8. Power at 5 V5² ÷ 4,700 Ω = 5.32 mW
9. Result4.7 kΩ SMD Resistor
Test It Out of Circuit
Lift one end or remove the part, then measure. Other parts on the board can pull the reading low.

472, 103 and 4R7 in an SMD Resistor Code Calculator

An SMD resistor marked 472 is 4.7 kΩ. The first two digits are the value and the last digit is the number of zeros, in ohms, so 472 reads as 47 followed by two zeros: 4,700 Ω.

R is the resistance in ohms, D1D2 is the two-digit number printed first and n is the last digit. On 4-digit codes the first three digits are the value, so 4701 is 470 × 10 = 4.7 kΩ and 4992 is 49.9 kΩ.

Count the characters before any SMD resistor code calculator lookup. Three digits point to a 5% part, four digits to a 1% part, and two digits plus a letter to the EIA-96 table below.

3-digit codeResistance4-digit codeResistance
10010 Ω1000100 Ω
22022 Ω2200220 Ω
101100 Ω4700470 Ω
471470 Ω10011 kΩ
1021 kΩ47014.7 kΩ
3323.3 kΩ100210 kΩ
4724.7 kΩ499249.9 kΩ
10310 kΩ1003100 kΩ
47347 kΩ7503750 kΩ
104100 kΩ10041 MΩ
1051 MΩ47044.7 MΩ

A 4-digit SMD resistor code calculator result is never a different value from the 3-digit one, only a finer one. Code 1002 and code 103 are both 10 kΩ; the extra digit lets 1% parts show values like 49.9 kΩ.

Code 100 is the one that catches people out. It looks like 100 Ω, but the last 0 adds no zeros, so the part is 10 Ω; a 100 Ω part is marked 101 or, on a 4-digit part, 1000.

Below 10 Ω the letter R stands in for the decimal point, so 4R7 is 4.7 Ω and 1R0 is 1 Ω. Four-character forms such as 15R0 carry one more digit, and R010 is 0.010 Ω, a current-sense value.

The same 4.7 kΩ appears as 472 on a 5% part and 4701 on a 1% part, so an SMD resistor code calculator reading is partly a tolerance clue as well as a value.

Through-hole parts mark that value with yellow, violet and red bands instead of digits, and the Resistor Color Code Calculator decodes those bands.

EIA-96 Codes Like 01C and 68X

An SMD resistor marked 01C is 10 kΩ. In the EIA-96 system the two digits are not the value but a position in the 96-value 1% table, so 01 means 100, and the letter C multiplies it by 100.

LetterMultiplierExampleResistance
Z× 0.00101Z0.1 Ω
Y or R× 0.0101Y1 Ω
X or S× 0.168X49.9 Ω
A× 188A806 Ω
B or H× 1066B4.75 kΩ
C× 10024C17.4 kΩ
D× 1,00001D100 kΩ
E× 10,00096E9.76 MΩ
F× 100,00001F10 MΩ

An EIA-96 value in any SMD resistor code calculator is the table entry times the letter. Index 68 is 499, so 68A is 499 Ω and 68X is 49.9 Ω, while 24C is 174 × 100, or 17.4 kΩ.

EIA-96 exists because 0603 parts only have room for three characters. Yageo's RC_L datasheet marks 0603 ±1% E96 values this way, with Y for × 0.01 and X for × 0.1; the R, S and H letters come from other makers.

E24 and E96 overlap in only six values: 10, 11, 13, 15, 20 and 75. In an SMD resistor code calculator check, a 1% 0603 part of those values takes an EIA-96 code. Other E24 values at 1%, such as 47 kΩ, carry a 3-digit code with a short bar under it.

That split is why a 1% 4.7 kΩ part has no exact EIA-96 code. The nearest entry is 66B, 4.75 kΩ, so a 0603 marked 66B is an E96 part rather than a 4.7 kΩ one that drifted.

Underlines, R Letters and Milliohm Marks

A short bar under a 3-digit 0603 code means a 1% part from the E24 series. The same Yageo datasheet describes one short bar under the marking for 0603 ±1% E24 values, so an underlined 473 is 47 kΩ ±1%.

A bar under the whole code means something else on some current-sense parts, where it puts an R in front. On those, an underlined 068 reads as R068, or 0.068 Ω, rather than 6.8 Ω, so the part's datasheet decides which reading applies.

Two digits and an R are the most common mixed-up marking. As EIA-96, 10R is index 10 at × 0.01, or 1.24 Ω, while read with R as a decimal point it is 10 Ω, a factor of eight apart in any SMD resistor code calculator reading.

Because Yageo's EIA-96 table uses Y rather than R, a 10R or 47R on a 5% part is far more likely 10 Ω or 47 Ω. A meter settles any SMD resistor code calculator doubt in seconds, since 47R would otherwise mean 3.01 Ω.

Milliohm current-sense parts use M or L as the decimal point in milliohms, so 1M50 is 1.50 mΩ. A 10 mΩ R010 part carrying 2 A drops just 20 mV and dissipates 40 mW, which is why ordinary meter leads read it wrong.

Case Size, Wattage and Voltage Limits

A 4.7 kΩ 0603 resistor can take up to 21.7 V before it reaches its 1/10 W rating. The safe voltage on any chip resistor is the lower of two limits: the power rating and the case's maximum working voltage.

Vmax is the highest continuous voltage, P is the rated power in watts at 70 °C, R is the resistance in ohms and Vwork is the case's maximum working voltage. Yageo uses this same rule in its rated-voltage definition.

CasePower at 70 °CMax working VMax V at 4.7 kΩMax V at 100 kΩCritical resistance
02011/20 W25 V15.3 V25 V12.5 kΩ
04021/16 W50 V17.1 V50 V40 kΩ
06031/10 W75 V21.7 V75 V56.3 kΩ
08051/8 W150 V24.2 V112 V180 kΩ
12061/4 W200 V34.3 V158 V160 kΩ
12101/2 W200 V48.5 V200 V80 kΩ
20103/4 W200 V59.4 V200 V53.3 kΩ
25121 W200 V68.6 V200 V40 kΩ

A value from an SMD resistor code calculator says nothing about wattage, so the case size has to be read off the board. An 0603 is 1.6 × 0.8 mm and an 1206 is 3.2 × 1.6 mm, each with its own limit.

Critical resistance is where the two limits meet, Vwork² ÷ P. Below it, power sets the limit; above it, voltage does. A 100 kΩ part in 0603 sits above 56.3 kΩ, so its 75 V working limit governs.

The ratings match Yageo's RC_L series, rated at 70 °C. A hotter board derates them, and other makers rate the same case sizes differently, so the actual part's datasheet sets the final limit.

Small cases fail on power first, whatever the SMD resistor code calculator value. A 100 Ω part with 5 V across it dissipates 0.25 W, 2.5 times the rating of an 0603, so it needs at least a 1206 at 1/4 W; 4.7 kΩ at 5 V uses just 5.32 mW.

Jumpers and Unmarked 0402 Parts

An SMD part marked 0, 00, 000 or 0000 is a zero-ohm jumper, a link that bridges two pads. Yageo specifies jumpers at under 50 mΩ, so a jumper carrying 1 A drops less than 50 mV.

Only those four all-zero marks are jumpers. A code such as 001 or 0003 has zero as its value digits, so in any SMD resistor code calculator lookup it is a misread or a worn print, never 0 Ω.

On a jumper the current matters more than the voltage, since the part is rated in amps rather than watts. Check the rated current for the case size on the maker's datasheet before routing a supply through one.

A jumper is not a resistor and should never have a supply voltage across it. If a jumper sits where a voltage appears, the circuit has a fault or the part was fitted in place of a real resistor.

Many small chips carry no code at all. Yageo prints no marking on 0402, 0201 and smaller parts, so no SMD resistor code calculator can help with them, and the value has to come from a meter, the reel label or the board's parts list.

For 0805 and larger parts the SMD resistor code calculator rule is simple in Yageo's scheme. Values at 5% get three digits and values at 1% or 0.5% get four digits, whether the value comes from the E24 or the E96 series.

Marking and Testing Answers

Most SMD resistor code calculator questions come down to which marking system the part uses and how far its reading may stray. The answers below follow Yageo's marking rules unless they name another source.

What is a SMD resistor code calculator?

It is a converter between the short code printed on a chip resistor and its value in ohms, in both directions. An SMD resistor code calculator result covers 3-digit, 4-digit, EIA-96, R and milliohm markings.

The conversion matters because one value has several markings. A 10 kΩ part reads 103 at 5%, 1002 at 1% in 0805 and larger, and 01C at 1% in 0603, and all three are the same 10,000 Ω.

How do you mark a SMD resistor?

Makers mark by size and tolerance. A 0603 part at 5% gets a 3-digit code, an 0603 at 1% gets an EIA-96 code, parts of 0805 and larger at 1% get a 4-digit code, and 0402 and smaller get no marking.

The marking is printed on the top of the resistive layer during manufacture. On 0603 1% E24 values outside the E96 table, Yageo adds a short bar under the code to show the tighter tolerance.

How do I know if my SMD resistor is tolerance?

The code style shows the tolerance on most parts, and an SMD resistor code calculator range follows from it. A 3-digit code means 5%, so 472 should read 4.465-4.935 kΩ, and a 4-digit or EIA-96 code means 1%, so 4701 reads 4.653-4.747 kΩ.

A short bar under a 3-digit 0603 code also means 1%. Unmarked 0402 and smaller parts give no clue, so the tolerance has to come from the reel label or the part number, where Yageo uses J for 5% and F for 1%.

Do all SMD resistors use the same coding system?

Not all makers or sizes use one system. 3-digit, 4-digit and EIA-96 codes all follow the same E-series values, but the multiplier letters vary: Yageo uses Y and X, while other makers print R and S for the same × 0.01 and × 0.1.

Current-sense parts add their own marks, such as M for milliohms or a bar under the whole code. When a marking fits two systems in an SMD resistor code calculator, as 10R does, a resistance reading out of circuit is the quickest way to decide.

Can SMD resistor codes be confused with capacitor codes?

The digits follow the same rule, so 104 means 10 with four zeros on both. On a resistor that is 100 kΩ, while on a capacitor it is 100,000 pF, or 100 nF, decoded with the Capacitor Code Calculator.

The body tells them apart. Chip resistors usually have a black top with white printing, while ceramic chip capacitors are mostly tan or grey and usually unmarked, so a printed 104 on a black chip is a 100 kΩ resistor.

How do you test an SMD resistor?

Measure it out of circuit, or with one end lifted, on a resistance range. In circuit, other parts in parallel pull the reading down, so a good 10 kΩ part beside another 10 kΩ path reads close to 5 kΩ.

Compare the meter with the SMD resistor code calculator range for that code, not the nominal value. A good 5% 472 reads 4.465-4.935 kΩ, while a 1% 4701 reads 4.653-4.747 kΩ.

A burned part on a phone or laptop board often reads open or far high; replace it with the same value, tolerance and case size, and check that the voltage across it stays under the case's limit.