Crown Molding Calculator

Updated

Crown molding calculator for flat and nested miter and bevel angles at any corner and spring angle, plus the sticks to buy by room size with waste, scarf joints, drop and its cost.

Room, Crown Sticks & Spring Angle

Measure wall to wall at the ceiling; each room this size has 4 inside corners.

ft
ft
ft
°
ft
corners
corners
Corner Angle, Crown Size & Ceiling90° corners, 5 1/4 in crown
°
in
ft
rooms
Waste & Crown Price15% waste, $2.50/ft
%
$/ft
Crown Molding to Buy
7 Sticks of 8 ft Crown
Larger of the 15% waste rule (7) and the wall-by-wall cut plan (6)
50.6 Linear ft With Waste
Wall Length Around the Room44.0 ft
Length You Buy56.0 ft
Wall length plus the overhang outside corners need, plus your waste allowance for test cuts and mistakes.
31.62° Miter, 33.86° Bevel
Nested Miter, Bevel 0°45.00°
Flat for 45° Spring Crown35.26° / 30.00°
Compound saw settings for the crown laid flat, back down, plus the nested cut with the crown upside down.
4 1/8 in Drop Down the Wall
Projection Onto Ceiling3 1/4 in
Usual for 8 ft CeilingWithin 2 1/2 to 6 in
Drop and projection come from crown width and spring angle; snap the chalk line at the drop to keep runs straight.
$140.00 Crown Cost
Cost per Stick$20.00
Cost per Foot of Wall$3.18
Every stick you buy at your price per foot, so offcuts and the waste allowance are counted in the total.
Crown Layout Diagram4 scarf joints
12 ft12 ft10 ft10 ftDots mark inside corners, bars mark scarf joints at 8 ft sticks
Stick Length ComparisonEvery common length
Stick LengthSticks to BuyLength BoughtScarf JointsCost
8 ft756.0 ft4$140.00
10 ft660.0 ft2$150.00
12 ft560.0 ft0$150.00
14 ft456.0 ft0$140.00
16 ft464.0 ft0$160.00
Saw Setup for Each PieceFour pieces, both methods
PieceLaid Flat, Blade Tilted 33.86° LeftNested Upside Down, Bevel 0°
Inside corner, left pieceCeiling edge on fence, miter 31.62° right, keep left sideWall edge on fence, miter 45.00° right, keep right side
Inside corner, right pieceWall edge on fence, miter 31.62° left, keep left sideWall edge on fence, miter 45.00° left, keep left side
Outside corner, left pieceWall edge on fence, miter 31.62° left, keep right sideWall edge on fence, miter 45.00° left, keep right side
Outside corner, right pieceCeiling edge on fence, miter 31.62° right, keep right sideWall edge on fence, miter 45.00° right, keep left side
Crown Molding Miter Angle ChartAt 38° spring
Corner AngleFlat MiterFlat BevelNested Miter
60°46.84°43.03°60.00°
72°40.28°39.61°54.00°
90°31.62°33.86°45.00°
108°24.10°27.59°36.00°
120°19.57°23.20°30.00°
135°14.31°17.55°22.50°
150°9.37°11.77°15.00°
Step-by-Step Crown Molding Math10 steps
Wall length2 × (12.00 ft + 10.00 ft) × 1 = 44.00 ft
Crown on the wall5 1/4 in × cos 38° = 4 1/8 in drop; × sin 38° = 3 1/4 in projection
Order length44.00 ft × 1.15 = 50.60 ft
Waste rule⌈50.60 ft ÷ 8.00 ft⌉ = 7 sticks
Cut plan4 walls cut into 8 pieces, each scarf overlapping 3 1/4 in, offcuts packed with a 1/8 in kerf = 6 sticks
Flat miteratan(sin 38° ÷ tan 45°) = 31.62°
Flat bevelasin(cos 38° × cos 45°) = 33.86°
Nested miter90° - 90° ÷ 2 = 45.00°
Cost7 × 8.00 ft × $2.50/ft = $140.00
Sticks to buylarger of 6 and 7 = 7 sticks of 8 ft
Cut List Ready
Real corners are seldom exactly 90°, so check each with an angle finder and cut a test pair from scrap before the good stock.

Saw Angles Behind Every Crown Molding Calculator Result

Standard US 52/38 crown laid flat on a compound miter saw cuts a 90° corner at a 31.62° miter and a 33.86° bevel. Crown with a 45° spring angle needs 35.26° and 30.00° for the same corner.

In crown molding calculator math, laying crown flat changes one simple corner into two saw settings, because the molding leans out from the wall. Both angles depend on the corner angle and on how far the crown leans, its spring angle.

M is the miter angle, S the spring angle measured from the wall and W the corner angle between the two walls. For 52/38 crown in a square corner, M = atan(0.616 ÷ 1.000) = 31.62°.

B is the blade bevel. For the same corner, B = asin(0.788 × 0.707) = 33.86°. The DeWalt DW718 manual lists 31.62° and 33.85° for 52/38 crown, the same angle cut short at the second decimal.

CornerBevelMiterEdge Against the FenceKeep
Inside, left piece33.85° left31.62° rightTop of moldingLeft end
Inside, right piece33.85° right31.62° leftTop of moldingRight end
Outside, left piece33.85° right31.62° leftTop of moldingLeft end
Outside, right piece33.85° left31.62° rightTop of moldingRight end

DeWalt's chart for 52/38 crown with the broad back flat on the table, on a dual-bevel saw. A saw that only tilts one way cuts the other two pieces with the bottom edge against the fence instead, at the same two angles.

What is the crown molding calculator?

A crown molding calculator is a combined estimate of the miter and bevel for each corner and the number of molding sticks to buy, from the room size, spring angle and corner angles.

Both halves of a crown molding calculator answer matter on the same job. A 12 × 10 ft room with 52/38 crown takes 31.62° and 33.86° at all four corners and 7 sticks of 8 ft molding with 15% waste.

What is the miter angle for crown molding?

The miter for crown in a 90° corner is 31.62° laid flat with a 33.86° bevel, or 45° nested upside down against the fence with no bevel. Both cut the same joint.

Inside and outside corners use the same crown molding calculator angles. The difference is only which side of the blade the piece sits and which end you keep, as the table above sets out.

Why is crown molding cut at 31.6 degrees?

The 31.6° figure is the flat-cut miter for 52/38 crown in a square corner, the most common case in US homes. It comes from atan(sin 38°), since tan 45° is exactly 1, and pairs with a 33.9° bevel.

Most miter saws have a detent at 31.6° and a mark at 33.9° for this reason, so the standard corner needs no fiddly fine adjustment.

Those crown molding calculator for miter saw values only apply to 38° spring crown at 90°, so 45° spring crown or an out-of-square wall needs its own settings.

Spring Angle Mix-Ups Ruin Corners

Entering 52° instead of 38° for standard crown gives a 38.24° miter and 25.81° bevel instead of 31.62° and 33.86°, a corner that gaps by more than 6°. The spring angle must be measured from the wall.

In crown molding calculator terms, crown called 52/38 meets the wall at 38° and the ceiling at 52°, per the DeWalt manual. Crown called 45/45 sits at 45° to both. The table compares the three settings people mix up.

Spring Angle UsedFlat Miter at 90°Flat Bevel at 90°Drop on Wall, 5 1/4 in CrownProjection on Ceiling
38° (52/38 crown)31.62°33.86°4 1/8 in3 1/4 in
45° (45/45 crown)35.26°30.00°3 11/16 in3 11/16 in
52° (wrong for 52/38)38.24°25.81°3 1/4 in4 1/8 in

Drop is crown width times cos S down the wall, and projection is width times sin S out on the ceiling. Entering 52° flips them, which is why a crown molding calculator angle result can look right yet miss by several degrees.

How do you measure a crown molding angle?

Hold a short offcut upside down in a framing square, back flat against both legs, then measure the angle between the back flat that touches the wall leg and that leg's edge. On standard crown it reads 38°.

A simpler check before any crown molding calculator run is the two back flats. If one is clearly narrower than the other, the crown is 52/38; if they match, it is 45/45.

The corner angle itself comes from an angle finder for crown molding set against both walls, read as the full angle between them.

What's the difference between 38 and 45 degree spring angle crown molding?

A 38° crown stands more upright, with more drop on the wall than projection on the ceiling, and 45° crown splits them equally. On 5 1/4 in crown that is 4 1/8 in by 3 1/4 in against 3 11/16 in each way.

The saw settings differ by about 4° in each axis, 31.62° and 33.86° against 35.26° and 30.00°. Mixing stock with different spring angles in one room makes corners that cannot close at any setting.

What is the best angle for a crown molding?

No spring angle is better, but 52/38 is the US stock profile and fits most saw detents. A 45/45 crown reads larger on the ceiling and suits shallow wall space above windows and cabinets.

Match the angle to what the lumberyard stocks in the profile you want, before running a crown molding calculator. Every saw chart depends on that number, so check the end of a stick before cutting.

Odd Corners From 60° to 150°

A 135° corner, common at bay windows, takes a 14.31° miter and 17.55° bevel for 52/38 crown laid flat, or a 22.5° miter nested. Using the 90° settings there leaves each piece 22.5° off.

Corner Angle52/38 Flat Miter52/38 Flat Bevel45/45 Flat Miter45/45 Flat BevelNested Miter
60°46.84°43.03°50.77°37.76°60.00°
72°40.28°39.61°44.22°34.89°54.00°
90°31.62°33.86°35.26°30.00°45.00°
108°24.10°27.59°27.19°24.56°36.00°
120°19.57°23.20°22.21°20.70°30.00°
135°14.31°17.55°16.32°15.70°22.50°
150°9.37°11.77°10.73°10.55°15.00°

Corner angle is the angle between the two walls, read with an angle finder. An outside corner of 270° uses the same settings as a 90° inside corner, since only the side you keep changes.

Tight corners push saws past their stops in any crown molding angle calculator chart. Many miter saws stop near a 45° bevel and a 50° miter, so a 60° corner in 45/45 crown, at 50.77°, is easier cut nested at 60° with no bevel.

Real walls are seldom exactly 90°. A drywall corner at 92° moves the 52/38 settings to 30.73° and 33.19°, and one at 88° to 32.52° and 34.53°, so reading the actual angle beats any crown molding angle cut chart. Flat trim such as casing and baseboard needs no bevel, and the Miter Angle Calculator gives its single miter for the same corner.

How do I cut 22.5 degree crown molding flat?

A 22.5° crown cut is the nested miter for a 135° corner. Laid flat, 52/38 crown at that corner needs a 14.31° miter and 17.55° bevel, and 45/45 crown needs 16.32° and 15.70°.

Use the flat crown molding calculator settings only when the saw lacks the fence height to nest the crown. Nested at 22.5° with no bevel is simpler and needs only one setting change between the two pieces.

Nested Cuts Need No Bevel

Cutting crown upside down, nested against the fence, needs only a miter: 45° for a 90° corner, 22.5° for 135° and 30° for 120°. The miter is 90° minus half the corner angle.

N is the nested miter and W the corner angle. Spring angle drops out because the crown sits on the saw exactly as it sits on the wall, with the ceiling edge on the table and the wall edge on the fence.

The trade-off against flat crown molding calculator settings is capacity. A 5 1/4 in crown at 38° spring stands 4 1/8 in up the fence, and wider crown needs a tall fence or a sliding saw. Flat cuts handle any width the saw can cross.

Is crown molding a 45 degree angle?

Crown cut nested is a 45° miter for a square corner, which is where the idea comes from. Laid flat, the same joint needs 31.62° and 33.86° on 52/38 crown, so 45° alone is only right for the nested method.

To cut 45° angles on crown molding, set the saw to 45° miter and 0° bevel, place the crown upside down with its ceiling edge on the table, and cut each piece of the pair from opposite sides of the blade.

Do you cut crown molding upside down?

For the nested method, the crown sits upside down, with the edge that meets the ceiling on the saw table and the edge that meets the wall against the fence. Flat cutting lays it face up with the back flat on the table.

Upside down is what makes the left-right logic of a crown molding installation angle chart feel reversed. An inside corner's left piece keeps its right side when nested, but its left end on DeWalt's flat chart.

Linear Feet Undercount Sticks

A 12 × 12 ft room has 48 ft of wall and needs 55.2 ft of crown with 15% waste, or 7 sticks of 8 ft by the length rule. Cutting each wall from whole sticks takes 8, because 12 ft walls leave 4 ft offcuts that will not fill the next wall.

RoomWall LengthWith 15% Waste8 ft Sticks by Rule8 ft Sticks by Cut PlanSticks to Buy
10 × 10 ft40 ft46.0 ft666
12 × 10 ft44 ft50.6 ft767
12 × 12 ft48 ft55.2 ft788
12 × 14 ft52 ft59.8 ft888
14 × 16 ft60 ft69.0 ft989
16 × 20 ft72 ft82.8 ft111011
20 × 24 ft88 ft101.2 ft131213

52/38 crown, 5 1/4 in wide, square corners. The crown molding calculator cut plan packs offcuts into the fewest sticks with a 1/8 in kerf between pieces, and the safe buy is whichever count is larger.

How do I calculate how much crown molding I need?

Add the lengths of every wall that gets crown, add 15% for test cuts and mistakes, then divide by the stick length and round up. A 12 × 10 ft room is 44 ft of wall, 50.6 ft with waste and 7 sticks of 8 ft.

Outside corners need a little more in any crown molding calculator count, since each piece runs past the wall corner by the crown's projection. One outside corner adds about 6 1/2 in for 5 1/4 in crown at 38° spring, before the waste allowance.

Check the result wall by wall. For a 12 × 12 ft room, how much crown molding you need in sticks is 8, not 7, because the offcuts are too short to reuse, so a crown molding calculator for square feet or linear feet alone runs short.

How much extra crown molding should I add for waste?

For a crown molding calculator waste allowance, add 15% for a simple room with four corners, and 20% or more where there are many short walls, bump-outs or outside corners. On a 48 ft room, 15% adds 7.2 ft, about one extra 8 ft stick.

Waste covers the test pairs every installer cuts from scrap before the good stock, plus miter offcuts too short to reuse. Rooms with long walls waste less once the sticks match the wall lengths. Baseboard runs along the same walls, and the Baseboard Trim Calculator counts its pieces from the same room size.

Longer Sticks, Fewer Scarf Joints

A 12 × 12 ft room needs 8 sticks of 8 ft with 4 scarf joints, or 5 sticks of 12 ft with none. At $2.50 per ft the 8 ft order costs $160 and the 12 ft order $150, so the longer stock is cheaper and cleaner.

Stick Length12 × 12 ft RoomScarf JointsExample Cost16 × 20 ft RoomScarf JointsExample Cost
8 ft84$160118$220
10 ft64$15096$225
12 ft50$15074$210
14 ft40$14064$210
16 ft40$16062$240

Example price of $2.50 per ft, 15% waste, 52/38 crown. Every stick bought is paid for in a crown molding calculator cost, offcuts included, so the cheapest length is the one that wastes least on your wall lengths.

A scarf joint splices two pieces on a long wall with matching 45° nested cuts, glued and nailed over a stud. Each joint overlaps by one ceiling projection, 3 1/4 in on 5 1/4 in crown, so a 16 ft wall needs more than two 8 ft sticks.

Fewer joints mean less filling and sanding, so 14 ft stock in a 12 × 12 ft room wins on both cost and finish at $140.

What lengths does crown molding come in?

Crown molding is sold in 8, 10, 12, 14 and 16 ft lengths in most US yards, and 2.4 to 4.8 m sticks in metric markets.

Match the stick to the longest wall where possible when choosing crown molding calculator lengths. A 14 ft stick covers a 14 ft wall in one piece, while 8 ft stock needs a scarf joint on any wall over 8 ft.

An 8 ft wall fits one 8 ft stick with no margin, because each miter's long point sits right at the stick end, so buy a spare.

How much does crown molding cost per linear foot?

Prices vary widely by profile, width and material, so set your own price per foot. At an example $2.50 per ft, a 12 × 10 ft room costs $140 for 7 sticks of 8 ft.

A crown molding cost calculator figure should include the full sticks bought, not just the wall length. The 12 × 10 ft room has 44 ft of wall but buys 56 ft, so pricing the wall alone would undercount by $30.

Drop and Projection Set the Chalk Line

A 5 1/4 in crown at 38° spring drops 4 1/8 in down the wall and projects 3 1/4 in onto the ceiling. Snapping a chalk line at that crown molding calculator drop on every wall keeps runs straight and corners matched.

Crown Width Across the BackDrop at 38°Projection at 38°Drop at 45°Projection at 45°
3 1/2 in2 3/4 in2 1/8 in2 1/2 in2 1/2 in
4 1/4 in3 3/8 in2 5/8 in3 in3 in
5 1/4 in4 1/8 in3 1/4 in3 11/16 in3 11/16 in
6 1/4 in4 15/16 in3 7/8 in4 7/16 in4 7/16 in
7 1/4 in5 11/16 in4 7/16 in5 1/8 in5 1/8 in

Drop is width × cos S and projection is width × sin S, rounded to the nearest 1/16 in. The drop is the size the eye reads from below, so it is the number to compare against the ceiling height.

How to choose crown molding size?

The Horner Millwork sizing guide, used in this crown molding calculator check, puts crown at 2 1/2 to 6 in for 8 ft ceilings, 3 to 7 1/2 in for 9 ft ceilings and at least 4 in from 10 ft up. Wider rooms carry the larger end of each range.

For a 9 ft ceiling, 5 1/4 in crown at 38° spring drops 4 1/8 in, near the middle of the range, and 7 1/4 in crown drops 5 11/16 in for a heavier look. Above windows and cabinets, the drop must also clear the trim below.

Ceiling height also sets how the crown reads against window casing and door heads. Crown that drops past 6 in on an 8 ft ceiling tends to crowd door casings, so judge size by drop rather than the width on the label.