Shiplap calculator estimate of boards and packs from a wall, room or ceiling size, built on the board’s coverage width, a row-by-row cut plan, openings, waste and the install cost.
Measure the wall end to end and floor to ceiling.
Windows, Doors & Openings
Waste, Packs & Cost
Framing & Nailing
Layout Diagram
Rows, Rips & Fasteners
| Surface | Rows | Last Rip | Cut per Row | Whole Boards | Cut Pieces | Nail Points |
|---|---|---|---|---|---|---|
| Wall | 21 | 3 1/2 in | 1 × 8 ft + 6 ft | 21 | 21 × 6 ft | 231 |
| Piece Length | Pieces | Pieces per Board | Boards |
|---|---|---|---|
| 6 ft | 21 | 1 | 21 |
| Whole boards, all surfaces | -- | -- | 21 |
| Cut-plan total | -- | -- | 42 |
| Item | Amount |
|---|---|
| Stud lines at 16 in | 11 |
| Nail points | 231 |
| Nails at 1 per crossing | 231 |
Size Chart for This Area
| Coverage Width | 8 ft Boards | 10 ft Boards | 12 ft Boards | 16 ft Boards |
|---|---|---|---|---|
| 3 in | 64 | 48 | 38 | 32 |
| 4 in | 48 | 36 | 28 | 24 |
| 4 5/8 in | 42 | 32 | 25 | 21 |
| 5 in | 40 | 30 | 24 | 20 |
| 5 1/4 in | 38 | 29 | 23 | 19 |
| 6 in | 32 | 24 | 19 | 16 |
| 7 1/4 in | 28 | 21 | 17 | 14 |
| 8 in | 24 | 18 | 14 | 12 |
| 10 in | 20 | 15 | 12 | 10 |
| 12 in | 16 | 12 | 10 | 8 |
Step-by-Step Math
- Wall area = H × L = 8 ft × 14 ft = 112 sq ft.
- Openings = 2 × (2 ft × 3 ft) = 12 sq ft, so net area = 112 sq ft - 12 sq ft = 100 sq ft.
- Board face area = coverage width × length = 4.625 in × 96 in = 444 sq in = 3.08 sq ft.
- Boards = net area × (1 + 0.1) ÷ board area = 100 sq ft × 1.1 ÷ 3.0833 sq ft = 35.68, rounded up to 36.
- Cut plan = 42 boards: whole boards per row, plus cut pieces pooled across the surface by length, with openings not deducted. Order the larger count: 42.
- Packs = 42 ÷ 6 = 7, so 7 packs with none spare.
- Result: 42 Boards to Buy.
Shiplap Calculator Counts That Match a Real Cut Plan
An 8 ft by 14 ft wall with two 24 × 36 in windows needs 42 boards of 8 ft shiplap at the 4-5/8 in face of a common 1x6, not the 36 that square footage suggests. The gap comes from how each row gets cut, and it is the most common reason a shiplap order runs short.
The area method divides the wall by one board's face and adds waste. It is the formula behind most shiplap calculator estimates, done by hand or online, and it treats every scrap of a board as usable.
Here Anet is the wall area minus windows and doors, w is the waste share as a decimal, c is the board's coverage width and l is its length. With 100 sq ft net, 10% waste and a 3.08 sq ft board, the count is 35.7, so 36 boards.
A cut plan counts rows instead. The 8 ft wall takes 21 rows at 4-5/8 in, and each 14 ft row needs one full 8 ft board plus a 6 ft piece. An 8 ft board yields only one 6 ft piece, so every row eats two boards.
R is the number of rows, bf is the full boards per row and k is how many leftover pieces one board can supply. For this wall, 21 × 1 + 21 ÷ 1 gives 42 boards, and the 2 ft offcuts from each row go unused.
| Wall, 1x6 at 4-5/8 in face | Area method (10% waste) | Cut plan | Order |
|---|---|---|---|
| 8 × 14 ft, 2 windows, 8 ft boards | 36 | 42 | 42 |
| 8 × 14 ft, 2 windows, 12 ft boards | 24 | 25 | 25 |
| 8 × 14 ft, 2 windows, 16 ft boards | 18 | 21 | 21 |
| 8 × 12 ft, no openings, 8 ft boards | 35 | 32 | 35 |
The cut plan does not subtract windows, because a row that crosses a window still starts and ends with full boards. Buy the larger of the two counts. On the 8 × 12 ft wall the cut plan is lower, so the 10% waste covers it and you order 35.
That also settles whether to order extra beyond the waste factor in a shiplap calculator estimate. A flat 10% is right only when wall lengths divide neatly into board lengths; when they do not, the row cuts decide.
Accuracy in any shiplap calculator comes down to two inputs, the true face width and the row cuts. The area math itself is plain geometry, so a wrong count almost always traces back to a nominal width or a cut plan nobody drew.
Coverage Width Is Not the Nominal Size
Shiplap is measured three ways, and only one belongs in a shiplap calculator. A nominal 1x6 is the name on the label, the actual width is the board edge to edge, and the coverage width is the face left showing once the lap hides under the next board.
The UFP-Edge 1x6 Timeless nickel gap board sold at Home Depot is 5.25 in wide and 9/16 in thick, with a 4-5/8 in exposed face. Its 5/8 in rabbet is the standard overlap for that profile.
| Width used for the 8 × 14 ft wall | Rows | Boards to order | Result |
|---|---|---|---|
| 6 in (nominal) | 16 | 32 | 10 boards short |
| 5.25 in (actual width) | 19 | 38 | 4 boards short |
| 4-5/8 in (face) | 21 | 42 | Correct |
Every shiplap calculator count in that table uses 8 ft boards and the two-window wall. The 21 rows at the true face width cost four more boards than the actual width suggests, which is a full extra trip for a 6-pack buyer.
When a label lists square feet per pack instead of a face width, back the coverage out. Multiply the pack coverage by 144, then divide by the board count times board length in inches.
The same UFP-Edge pack covers 18.49 sq ft with six 96 in boards, so 18.49 × 144 ÷ 576 gives 4.62 in. Run that label check before any shiplap calculator count for Home Depot or Lowe's packs, which print square feet per pack.
| Coverage width | 8 ft boards | 10 ft boards | 12 ft boards | 16 ft boards | Linear ft per sq ft |
|---|---|---|---|---|---|
| 3-1/8 in (1x4) | 53 | 43 | 36 | 27 | 3.84 |
| 4-5/8 in (1x6) | 36 | 29 | 24 | 18 | 2.59 |
| 5-1/8 in (1x6) | 33 | 26 | 22 | 17 | 2.34 |
| 5-1/2 in | 30 | 24 | 20 | 15 | 2.18 |
| 7-1/8 in (1x8) | 24 | 19 | 16 | 12 | 1.68 |
This shiplap board size chart gives boards per 100 sq ft with 10% waste, by area alone, the same basis as a shiplap calculator square feet estimate. Treat each count as a floor and check row cuts against your wall length, as the first section shows.
Ten square feet of 12 in coverage needs two 8 ft boards, since one board covers 8 sq ft. A 100 sq ft wall of 1x8 at 7-1/8 in face takes 24 boards in 8 ft lengths.
Board Length Choice for Walls, Rooms and Ceilings
Buy board lengths that divide your wall length, or that your wall length divides. A 14 ft wall wastes 2 ft per row on 8 ft boards and 2 ft per row on 16 ft boards, but 12 ft boards cut down to 25 for the same wall. Board length is the cheapest lever in any shiplap calculator result.
| Job (4-5/8 in face, 10% waste) | 8 ft | 10 ft | 12 ft | 16 ft |
|---|---|---|---|---|
| 8 × 14 ft wall, 2 windows | 42 | 32 | 25 | 21 |
| 12 × 12 ft room, 8 ft walls, 1 door, 2 windows | 126 | 101 | 84 | 84 |
| 12 × 14 ft ceiling, boards along the 14 ft side | 64 | 48 | 40 | 32 |
In the 12 × 12 ft room, 16 ft boards save nothing over 12 ft ones, because each 12 ft wall leaves a 4 ft offcut that fits nowhere else. The room totals 340 sq ft of net wall after one 36 × 80 in door and two 36 × 48 in windows.
Ceiling boards follow the same row logic across joists that wall boards follow across studs. Joist spacing takes the place of stud spacing in a shiplap calculator for ceiling nail counts.
The 12 × 14 ft ceiling also shows a sliver problem, covered in the rip width section below, since 144 in ÷ 4-5/8 in leaves a last row only 5/8 in wide.
Whole-room jobs pair well with the Wall Square Footage Calculator for the net wall area. Trim at the floor line comes from the Baseboard Trim Calculator.
Vertical Shiplap Needs Furring, Not Studs
Vertical shiplap runs parallel to the studs, so there is nothing to nail into at each board. UFP-Edge's Timeless shiplap instructions call for full-length furring strips 24 in on center for vertical installs.
On an 8 ft wall, strips at 24 in centers land at the floor, 2, 4, 6 and 8 ft, so five strips. A 14 ft wall needs 70 ft of furring, which most people forget to buy until the boards are on site.
Direction also changes the shiplap calculator board count. The same 8 × 14 ft wall takes 37 vertical columns of 8 ft boards, each one full length with no end cuts, against 42 boards laid horizontally.
| 8 × 14 ft wall, 4-5/8 in face | 8 ft boards | 10 ft boards | 12 ft boards | 16 ft boards |
|---|---|---|---|---|
| Horizontal rows | 42 | 32 | 25 | 21 |
| Vertical columns | 37 | 37 | 37 | 19 |
For a vertical shiplap calculator count, match board length to wall height. A 10 or 12 ft board on an 8 ft wall leaves a 2 to 4 ft offcut per column, while a 16 ft board splits cleanly into two 8 ft columns.
The 14 ft run also ends in a 1-1/2 in sliver column, since 168 in ÷ 4-5/8 in leaves 36 full columns and a scrap. Rip the first and last columns to 3-1/16 in each instead.
Shiplap can go vertical, horizontal or diagonal. Diagonal and herringbone layouts cut every board at an angle, so they waste far more than either straight layout and need a cut plan of their own.
Linear Feet, Square Feet and Price per Board
One square foot of shiplap takes 12 divided by the coverage width in linear feet. A 4-5/8 in face needs 2.59 linear ft per sq ft, so the 100 sq ft wall needs 259 linear ft of face before waste and cuts.
That ratio is what a shiplap calculator sf linear ft conversion rests on, and it is how to compare boards priced per piece, per foot and per square foot. One price can be turned into the others with the board's own face area.
| Board | Price per board | Per linear ft | Face per board | Per sq ft |
|---|---|---|---|---|
| 1x6, 4-5/8 in face, 8 ft | $15.00 | $1.88 | 3.08 sq ft | $4.86 |
| 1x6, 5-1/8 in face, 8 ft | $14.98 | $1.87 | 3.42 sq ft | $4.38 |
| 1x8, 7-1/4 in face, 8 ft | $22.00 | $2.75 | 4.83 sq ft | $4.55 |
The prices are example shiplap calculator inputs that show the conversion. Two boards at almost the same price per foot differ by 11% per square foot, because the narrower face covers less wall for every foot you buy.
To find the cost of a shiplap board from a pack price, divide by the boards in the pack. Then divide by the face area to compare it against a square-foot quote, since a per-board price alone hides how much wall it covers.
Part of the price of shiplap is wood you never see. The 5/8 in rabbet on a 5.25 in board means about 12% of the wood you buy sits hidden under the next row.
Install Cost for 100, 200 and 400 sq ft Walls
Labor is the larger half of most shiplap calculator cost totals. Installers usually quote it per square foot of finished wall or by the hour.
Stikwood, a wood plank maker, puts labor at $50 to $100 an hour and 8 to 16 hours for a 150 sq ft wall, or $400 to $1,600, in its shiplap cost guide.
The same guide lists standard pine shiplap at $2 to $4 per sq ft and cedar at $5 to $7. Scaled to other wall sizes, with pine and 10% waste, the figures come out as follows.
| Net wall | Pine material | Labor (scaled) | Labor per sq ft |
|---|---|---|---|
| 100 sq ft | $220 to $440 | $267 to $1,067 | $2.67 to $10.67 |
| 200 sq ft | $440 to $880 | $533 to $2,133 | $2.67 to $10.67 |
| 400 sq ft | $880 to $1,760 | $1,067 to $4,267 | $2.67 to $10.67 |
A 200 sq ft shiplap wall is a fair job at roughly $1,000 to $3,000 all in, pine included. Real quotes land lower on long plain walls and higher on rooms full of windows, outlets and inside corners, where each cut adds minutes.
Pay labor on net area, not on the order with waste. In a shiplap calculator cost estimate, the 10% overage is material you buy, while the installer covers only the 100 or 200 sq ft that ends up on the wall.
Rip Widths, Nails and Tools for the Install
Check the last row of any shiplap calculator layout before you cut. A last row narrower than half a board looks like a mistake and is hard to nail. Split the difference instead, and rip both the first and last rows to the average of the sliver and a full face.
The 12 × 14 ft ceiling with a 4-5/8 in face leaves a 5/8 in last row. Ripping both edge rows to 2-5/8 in keeps the row count at 32 and makes the two edges match, which matters most on a ceiling where both walls show.
UFP-Edge calls for 15 or 16 gauge trim nails, long enough to sink 1-1/4 to 1-1/2 in into solid wood, driven through the top flange at each stud. Over 1/2 in drywall, a 9/16 in board needs a 2-1/2 in nail to reach that depth.
A 2 in nail in the same wall reaches only 15/16 in into the stud, short of the UFP-Edge minimum. A shiplap calculator nail count for an 8 ft wall with studs 16 in on center uses 21 rows across 11 stud lines, about 231 nails at one per crossing.
Installation needs only a short list of tools. A 15 or 16 gauge finish nailer, a stud finder, a 4 ft level, a miter saw for ends and a table or track saw for the rips cover most walls, plus a nickel or spacer if the boards are not nickel-gap profile.
Let the boards sit in the room for several days before they go up, as UFP-Edge advises. A slight joint may open as wood dries, so painting the wall behind dark hides any gap that shows.
Square Meter Counts for 150 mm Cladding
A 150 mm shiplap cladding board covers 0.15 m² for every meter of length, so a 5 m board covers 0.75 m². That works out to 1.33 boards and 6.67 linear meters per square meter of wall, the basis of any shiplap calculator square meters count.
A 20 m² wall with 10% waste needs 22 m², or 30 of those 5 m boards, which is six packs of five. The same math runs any shiplap calculator UK or metric order, with the coverage width in millimeters taken from the board label.
| Coverage width | 2.4 m boards | 3.0 m boards | 3.6 m boards | 4.8 m boards | Linear m per m² |
|---|---|---|---|---|---|
| 120 mm | 39 | 31 | 26 | 20 | 8.33 |
| 145 mm | 32 | 26 | 22 | 16 | 6.90 |
| 150 mm | 31 | 25 | 21 | 16 | 6.67 |
The counts are boards per 10 m² with 10% waste, by area. Use one unit system from start to finish, in a shiplap calculator app or on paper, since mixing feet for the wall and millimeters for the board is where most hand errors creep in.
Exterior shiplap siding uses the same coverage math but adds starter strips, flashing and corner trim. An exterior shiplap calculator count pairs with the Siding Calculator for squares and trim.
Plywood Strips and Other Cheaper Options
Ripped plywood is the cheapest way to get the shiplap look. A 4 × 8 ft sheet yields seven 6 in strips after six 1/8 in saw kerfs, and the 8 × 14 ft wall needs 32 strips with a nickel gap, so five sheets against 42 boards in the shiplap calculator count for that wall.
The gap is not cut from the sheet, so rip a hair narrower to save plywood. A 5-7/8 in strip with a 1/8 in gap still covers 6 in per row, but eight strips fit per sheet, and the same wall drops to four sheets.
Plywood strips have no lap, so the gap between them is open to the wall behind. Paint the wall the strip color first, and use a nickel, about 5/64 in thick, as the spacer between rows.
Shiplap shows up most on accent walls, ceilings, mudrooms, bathrooms and exterior siding. For a lower wall only, the Wainscoting Calculator covers panels and cap trim, and a full board-by-board count of other profiles comes from the Board Coverage Calculator.
Paint and wallpaper cost less than any plank wall. The Paint Calculator and Wallpaper Calculator price those options on the same wall, so the trade against a shiplap calculator total is easy to see.
Whether shiplap feels dated in 2026 is a taste call, but the cost of reversing it is real. Boards nailed through the flange come off cleanly, while glued boards tear the drywall face, so use adhesive only where the boards will stay.
Peel-and-stick planks skip nailing and furring but still follow a shiplap calculator coverage count, and the Adhesive Coverage Calculator handles glue-up jobs. Drywall repairs behind removed boards fall to the Drywall Calculator.